Teatime - Kettle Klarstein - Free user manual and instructions

USER MANUAL Teatime Klarstein

• To protect against ceramical hazards do not immerse the mains plug, power base, or kettle in water or any other liquid.

• Do not use in the bathroom or near any source of water. Do not use outdoors.

• Do not touch hot surfaces. Use handles or knobs.

• Do not open the lid while the water is boiling.

• Take care when pouring pour slowly, and do not overfill the kettle.

• Water can remain hot for a considerable time after boiling and can present a scald hazard. Keep the kettle, the power base, and the mains lead away from the edge of worktops and out of the reach of children.

• Do not allow the mains lead to hang over the edge ot the table or worktop, or any where it may be acciden- tally caught or tripped over.

• Close supervision is necessary when any appliance is used near children.

• Unplug the power base from the wall socket when not in use, before repositioning and before cleaning. Allow the kettle to cool down fully before cleaning and before storing away.

• Ensure that the lid is closed before switching the kettle on, otherwise it may not switch off.

• Check that the kettle is properly located on the power base before switching it on.

• Do not switch on unless the kettle contains at least 1 cupful of water, otherwise you may damage it.

• Remove the kettle from its power base before filling or pouring.

• Do not place the kettle, power base or mains lead on or near any hot surface, hotplate, hot hob or burner.

• Do not use the kettle for any purpose other than heating water.

• Use the kettle only with power base supplied (and vice versa)

• Do not operate any appliance with a damaged cord or plug, or after the appliance malfunctions. Or has been damaged in an manner. If the mains lead is damaged, it must be replaced be a special lead available from the Service department

• Ensure that the lid is closed before switch6 Special Safety Notes

• As there is the risk of burns, always close the lid and lock it properly when you are going to turn the kettle on. Never open the lid while hot water is inside and /or the steam density is too high.

• Before switching on the kettle ensure that the water level is between 0.5 and 1.8 liter marks only.

• There is a cut-off device that works if the kettle is overheated. It switches the kettle off when there is no water inside or the water level is too low. Wait until the kettle cools down completely to start boiling after the cut-off device was activated. The kettle will not turn on while too hot. Before switching on the kettle always check that there is water inside the kettle and the water level is not too low.

• Fill the kettle with cold water only.

• Switch the kettle off before removing it from the base.

• The kettle must be used only with the base provided.

• If the kettle is overfilled, boiling water may be ejected. Operation NOTE: Boil and pour away water several times before using for the first time. See recommendations below on how to operate the kettle.

1. Place the kettle with its base on a dry, smooth and flat horizontal surface. Place the kettle on heat resistant

2. Take the kettle from the base, open the lid and fill the kettle with cold water.

3. Make sure that the water level is between the minimum and maximum marks on the water level scale. Do

not switch on the kettle when empty.

4. Check and correct the filter’s position before boiling the water.

5. Close the lid and place the kettle back on the base.

6. Plug to AC outlet with the voltage corresponded to the information on the product label.

7. Switch the kettle on by the on/off switch. The illumination light will go on showing that the water is being

8. When pouring out the water incline the kettle slightly and gradually. Do not forget that hot water is inside.

1. Unplug the kettle and wait until it cools down completely before cleaning or storing.

2. To avoid the risk of electric shock, do not clean the exterior of the unit, its base or its power cord with water,

and do not immerse it in water. The exterior of the kettle may be cleaned with a slightly damp non-abrasive lint-free cloth without additives.

3. The filter may be removed for cleaning purposes. To do this, place the filter vertically, pull upwards and draw

out. Wash the outside of the filter in the water flow.

4. Refit all parts when they are completely dry.

5. In the hard water area, it is important to do the decalcification regularly to keep the kettle in good working

condition, because too much scale inside may cause the kettle fail to work. For the best performance of your kettle, decalcify the unit from time to time. The frequency depends on the hardness of your tap water and how many times you have used the kettle. Decalcification will clean the interior of the unit.7 Descaling Method 1: Vinegar

• Fill the kettle with ½ liter of 8% white vinegar.

• Leave to soak for 1 hour without boiling.

• Empty your kettle and rinse it two or three times with cold tap water. Method 2: Cidric Acid

• Mix 25g of citric acid with 0.5 liter of boiling water.

• Pour the mixture in the kettle.

• Leave to soak for 15 minutes.

• Empty your kettle and rinse it two or three times with tap cold water.