IAN 275342 - Bike helmet CRIVIT - Free user manual and instructions

USER MANUAL IAN 275342 CRIVIT

3. Size adjustment system

8. Padding for size adjustment

des tailles6 Congratulations! With your purchase you have decided on a high-quality product. Get to know the product before you start to use it. Carefully read the following instructions for use. Use the product only as described and only for the given areas of application. Keep these instructions safe. When passing the product on to a third party, always make sure that the documentation is included. Important information Please read the following instructions and information carefully before using your new helmet for the first time. This helmet was deve- loped for use with bicycles, skateboards, inline skates, roller skates and similar groups, and manufactured according to state of the art. Despite maximum safety standards, serious accidents may result in injuries. In some cases, the impact may be so strong the helmet does not effectively protect the rider from head injuries. Compliance with the requirements according to Annex II of European Directive 89/686/EEC (and subsequent amendments) as well as those of harmonizing technical standard EN 1078 was certified by the issuing authority TÜV Rheinland LGA Products GmbH, Tillystr. 2, D-90431 Nürnberg, Germany, Notified Body No 0197. Intended use This article is made for bicycle riders, skateboarders, inline and roller skaters, and other groups with similar pursuits. It is not suitable for other sports or motorcycling. GB/IE7GB/IE Safety notices

• Do not allow children to wear this helmet while climbing or playing as this carries a risk of strangulation.

• The helmet must be firmly seated and the chin strap closed tightly.

• Do not shift the helmet toward the neck, as this will leave your forehead unprotected.

• Do not wear headgear under the helmet.

• Be sure not to restrict air circulation.

• Never modify the helmet, its structure or the individual components.

• Never paint the helmet and/or apply decals or labels.

• The impacts of paint, decals, cleaning liquids or other solvents can seriously impair the protection of the helmet.

• The helmet is intended to protect the head in the event of an impact. This protection is no longer warranted after just one (even minor) impact. The helmet must therefore immediately be replaced following an accident, even without visible damage.

• Never use solvents or abrasive cleaners containing petroleum to clean the helmet, neither inside nor outside. Always use a pH- neutral detergent diluted in clear water; carefully rub with a soft cloth. Then dry with a lint-free cloth. The padding may be cleaned with a little soap, using a soft brush.

• Only use OEM replacement parts for your helmet.

• The life of this product varies by use. However, the product must be replaced no later than five years from the date of manufacture (Version: 06/2016).8 FIDLOCK magnetic lock FIDLOCK magnetic lock This patented, globally unique lock technology is very simple to operate. The magnets move together almost on their own when closing the lock because of their attraction force. The magnetic locking force is assisted by mechanical lock-in position: the lock thus fixes securely and reliably. Only a small impetus is required when opening the lock: the magnets reverse their polarity when displaced and thus repel one another. Helmet sizing Size table Size S ‒ M L ‒ XL Head circumference 56 ‒ 59cm 60 ‒ 62cm

• Measure the circumference of the head and select the helmet size accordingly. Try several helmets before deciding. Ideally, the skin over your temples moves along when wearing the helmet.

• Verify the helmet does not move much on your head even with chin strap loose. GB/IE9

• The chin strap must be closed firmly for a secure seat. It is fitted correctly when it is difficult to slide your fingers under the chin straps. However, you must still be able to comfortably breathe, swallow and turn your head.

• The helmet is seated correctly if it is tight, yet comfortable on your head (Fig. B).

• If the helmet is too large (wiggles, cannot be adjusted tightly enough) or too small (pinches, forehead exposed), please select the next larger or smaller size.

• Two additional sets of internal pads of different thicknesses are supplied with the article for further size adjustment. If the fitted internal pads do not correspond to your head size, then remove them and replace them with a different pair of internal pads.

• Never use the helmet if it cannot be adjusted correctly. Adjusting the chin strap (Fig. C) The general length of the chin strap can be adjusted with the loop. You can also adjust the length of the chinstrap using the strap divider. Please ensure that the strap divider does not bother you, the straps do not cover your ears, and the fastener does not rest on your chin. GB/IE10 Headband width adjustment (Fig. D) Use the wheel for variable adjustment to your head size to ensure the helmet is seated optimally. Turn the wheel clockwise to tighten the headband and counter-clockwise to loosen the headband. Opening and closing the magnet lock (Fig. E/F) In order to close the buckle, slide the upper section of the buckle over the lower section. The magnets will click audibly into place. Pull on the chinstrap to test that the magnet lock is securely closed. In order to open the buckle, slide the upper section away from the lower section until the magnets release. Maintenance and care Regular maintenance and care contributes to ensuring the safety and preservation of the helmet.

• Always use a pH-neutral detergent diluted in clear water; carefully rub with a soft cloth. Then dry with a lint-free cloth.

• The padding may be cleaned with a little soap, using a soft brush. Inner pads