Tx07 - Bike accessory Prophete - Free user manual and instructions

Product Type	Bicycle Helmet
Brand	Prophete
Model	Tx07
Safety Standards	EN 1078:1997, PPE 89/686/EEC, GS and CE certified
Adjustment	Adjustment ring with rotary knob (turn right to tighten)
Straps	Adjustable strap holders, buckle closure
Lighting (depending on model)	LED with flashing modes (1 press), steady (2 presses), off (3 presses)
LED Power	Batteries (replaceable, type not specified)
Weight	Approximately 300-400 g (estimated for a standard bicycle helmet)
Shell Material	Rigid plastic (not specified, but typical for helmet)
Padding	Removable washable pads
Intended Use	Bicycle, skateboard, roller skates
Max Storage Temperature	60 °C
Maintenance	Clean with lukewarm soapy water; no solvents or paints
Recommended Lifespan	5 to 6 years after first use
Replacement After Impact	Mandatory after any serious fall, even without visible damage
Warranty	2 years from date of purchase (receipt required)
Spare Parts and Repairability	Pads, adjustment ring, straps and buckle available from manufacturer or retailer

Frequently Asked Questions - Tx07 Prophete

How to properly adjust the Prophete Tx07 helmet?

Place the helmet horizontally on your head, not too low on the forehead or on the back of the neck. Adjust the adjustment ring with the rotary knob: turn right to tighten, left to loosen. Then adjust the straps so that the strap holders are just under the ears, then close the buckle and tighten the ends.

How to clean the Prophete Tx07 helmet?

Clean the shell, removable pads, adjustment ring and straps with lukewarm soapy water. You can remove the pads and ring. Never use thinners or harsh detergents. Dry thoroughly before reassembling.

How to replace the batteries of the helmet (LED model)?

Follow the diagram in the manual: open the battery compartment (usually located at the back of the helmet), insert new batteries respecting polarity, then close. The battery type is not specified, check the used batteries.

When should I replace my Prophete Tx07 helmet?

Replace it after 5 to 6 years of use, or immediately after a serious fall, even if no damage is visible. Material wear reduces protection.

Can I paint or put stickers on the helmet?

No, do not paint or apply stickers. Chemical substances can damage the stability of the helmet and reduce its protection.

What is the warranty for the Prophete Tx07 helmet?

The warranty is 2 years from the date of purchase (upon presentation of the receipt). It covers material and functional defects, but excludes batteries, falls and impacts.

Is the Prophete Tx07 helmet suitable for skateboarding or roller skates?

Yes, it is certified according to EN 1078:1997, which covers bicycle, skateboard and roller skates. Do not use it for motorcycle or scooter.

How to adjust the helmet straps?

Start by adjusting the rear strap (B), then position the strap holders (C and D) just under each ear. Close the buckle (E) and pull on the ends (A and B) to tighten. Check regularly that the straps do not loosen.

What do the presses on the LED button mean?

1 press = flashing, 2 presses = steady on, 3 presses = off. These modes are available depending on the model.

Can I use this helmet for motorcycle or scooter?

No, this helmet is only designed for bicycle, skateboard and roller skates. It does not provide sufficient protection for motorized vehicles.

USER MANUAL Tx07 Prophete

prophete keep moving

D Bedienungsanleitung
I Manuale d'uso
F Notice d'utilisation
NL Gebruiksaanwijzing
GB Operating Instructions
PL Instrukcja obsługi
H Kezelési útmutató
RO Manual de utilizare

Inspected and certified by TÜV Rheinland (MOT Rhineland)

LGA Products GmbH, Tillystr.2,

D-90431 Nuernberg; notified Body Nr. 0197

Inhaltsverzeichnis

2. Helmanprobe

Batterie:

3V Lithium,

CR 2032

Batteria:

Litio 3V, CR

2032

Pile:

Lithium 3 V,

CR 2032

2. Helm passen

Batterij:

3V Lithium,

CR 2032

1. General information
2. Fitting the helmet
3. Adjusting the inner part
4. Adjusting the webbings
5. LED explanation

(model dependent)

1. Changing the battery (model dependent)
2. Recommendations for use, care and maintenance
3. Warranty provisions

1. General information

This bicycle helmet meets the highest safety requirements. It cannot, however, absolutely guarantee the prevention of injuries.

The safety standards applied in inspecting and approving the helmet include: PSA 89/686/EWG.

EN 1078: 1997 European standards of helmets for cyclists and users of skateboards and skates.

Please make absolutely sure that children remove their helmet before entering children's playgrounds. There is a risk of strangling if children get caught in the gaps of the nets when climbing while wearing the helmet.

This helmet is exclusively suitable for the exclusive use of bicycles, skateboards and skates and not for: mopeds, scooters and motorcycles.

2. Fitting the helmet

Optimal protection is only provided if the helmet fits securely.

The helmet should enclose the head properly and be worn in a horizontal position; it should not sit on the back of the head, and should not be tilted down towards the forehead or to one side.

3. Adjusting the inner part

Check that helmet is firmly fitted by a light shake of the head with the chin strap open. If the helmet slips about at all, then you must set the adjusting ring (1) more tightly.

This is done using the rotary knob (2). Turning it to the right will tighten it, and turning it to the left will loosen it.

4. Adjusting the webbings

In the event of an accident, the helmet will only optimally protect your head if the webbings are properly set and tightly closed.

Setting the webbings (Figures 1 + 2)

1. Push strap holder D up to the left ear.
2. Tighten nape strap B.
3. Push strap holder C up to the right ear and lock. Fig. 3
4. Close strap using buckle E. Fig. 4
5. Tighten strap by pulling the two ends of the strap A + B. Fig. 5

Check the setting at regular intervals to make sure that the strap has not become loose and that the helmet fits securely.

5. LED explanation (model dependent)

6. Changing the battery (model dependent)

Change the battery as shown in the illustrations below:

Battery: 3V Lithium, CR 2032

7. Recommendations for use, care and maintenance

• The helmet should be checked for any visible damage at regular intervals.
- Following a heavy fall, the helmet must be replaced, even if there is no visible damage to it.
- Only ride with strap closed.
- Do not paint or attach stickers to the helmet. Paint and stickers may contain components that reduce the stability of the helmet and therefore the protective effect.
- Do not make any modifications to the helmet. Only use original parts for repair.
- Do not expose the helmet to temperatures above 60 °C; this may result in the loss of its protective properties. Please do not leave the helmet near radiators or in the sun behind glass (e.g. in a car).
- The helmet shell, the detachable pads, the adjusting ring as well as the strap can be cleaned with lukewarm water using a mild soap solution. For this purpose, remove the pads and adjusting ring from the helmet. When putting the inner parts back in place afterwards, check for secure fit of the helmet. Do not use any solvent (e.g. thinner or similar) to clean the helmet.
- The bicycle helmet should be replaced after 5 - 6 years by a new one, as the optimal protection can then no longer be guaranteed due to the deterioration of the material properties.
- Dispose of the helmet with household waste (residual waste).

8. Warranty provisions

We provide a 2-year warranty for this bicycle helmet. The warranty period begins with the date of purchase (purchase receipt, proof of purchase). During the warranty period, please address any complaints concerning defective bicycle helmets to your dealer or the service address specified. In this period, we will repair all defects due to faulty operation free of charge. Batteries, defects caused by improper handling, a fall, impact and the like are excluded from the warranty. Please note that the warranty period is not affected by any repair or replacement. The 2-year warranty period starting from the purchase date shall remain in effect.

- Please keep the instruction manual in a safe place -

Spis treści

Bateria

litowa: 3V,

CR 2032

Elem:

3V lítium,

CR 2032

2. Probarea căștii

Baterie:

3V Litiu, CR

2032