K5740 - Watch Calypso - Free user manual and instructions

USER MANUAL K5740 Calypso

• The operation of buttons are indicated by using the letters shown in the illustration. A -- Reset B -- Mode C -- EL backlight D -- Start / Stop

• Press “B” to change mode to mode in the following Sequence: Timekeeping Mode - Alarm Mode - Stopwatch Mode - Dual Time Mode.

• Hour, Minutes, Seconds, Day of week, Date.

• The alarm sounds at the preset time each day.

• The time for other time zone.

• The screen shown in below:

• The backlight that uses an EL (electro-luminescent) cause the display to glow for easy reading in the dark. Use EL Backlight

• In any mode, press “C” to illuminate the display about 3 seconds.

1. In the timekeeping

mode,press and hold “A” until the seconds to flash (flashing indicated in set mode).

2. Press “D” to reset the

3. Press “B” change to the

4. Press “D” to increase the number,

press and hold to increase at high speed.

5. Repeat step 3 and 4, the selection in

the following sequence: Seconds - Hour - Minutes - Year Month - Date.

6. Press “A” to exit the set state,

after you set(The day of week is automatically displayed in accordance with year, month and date setting). 12/24H Format

• In the timekeeping mode, press “A” to switch between 12/24H formats. Calendar

• In the timekeeping mode, press and hold “D” to display: Year, Month, Date18 19 English English STOPWATCHALARM Alarm and Chime

• In the alarm mode, press “D” to on/off the alarm and chime in the following sequences: Alarm & Chime off - Alarm on Chime on - Alarm & Chime on. Alarm Time Setting

1. In the alarm mode, press “A” the hour to

flash(flashing indicated in set mode.

2. Press “D” to increase the hour, press and

hold to increase at high speed.

3. Press “B” to select the minutes.

4. Press “D” to increase the minutes,press and

hold to increase at high speed.

5. Press “A” to exit the set state, after you set.

• The alarm sounds at the preset time each day for about 60 seconds, press any button to break it. A Lap Time Split Time

1. In the stopwatch mode, press “D” to

start the stopwatch.

2. To stop the stopwatch by pressing

3. Press “A” to reset the stopwatch.

1. In the stopwatch mode,press “D” to start

2. Press “A” to display the split time,

stopwatch timing continues internally.

3. Press “A” to clear the split time and to

continue time measurement.

4. Repeat step 2 and 3, you can measure

themulti split time.

5. Press “D” to stop the stopwatch.20 21

English English DUAL TIME Dual Time Setting

1. In the dual time mode, press “A” the

hour to flash (flashing indicated in set mode).

2. 2. Press “D” to increase the hour, press

and hold to increase at high speed.

3. Press “B” to select the minutes.

4. Press “D” to change the minutes(press

once change 30 minutes).

5. Press “A” to exit the set state, after

This watch contains electronic components. Never attemp to open the case or remove the back cover.

2. Do not operate push buttons below the surface of the water while swimming

3. Should water or condensation appear in the watch, have the watch checked

inmediately. Corrosion of electronic parts can occur inside the case.

4. Avoid severe impact. The watch is designed to withstand impact under

normal use. It is inadvisable to subject it to severe impact of rough usage.

5. Avoid exposing the watch to extreme temperature.

6. Clean the watch with soft cloth and clean water only. Avoid using chemicals.

7. Keep your watch away from the conditions of strong electric field and estatic

electricity.23 English

English By virtue of the regulations pursuant to the handling of waste products deriving from electronic and electrical equipment, end of lifecycle watch making products must be selectively collected for processing. You may therefore dispose of your quartz watch making products at any of our retail outlets or any other authorized collection point. The selective collection, processing, rating and recycling of these products helps contribute to safeguarding the environment and protecting our health.24 25 Français Français BOUTONS SÉLECTION DES MODES DE CONFIGURATION