Dream - Baby bed Babyhome - Free user manual and instructions

USER MANUAL Dream Babyhome

Please read label carefully. Machine wash warm, gentle cycle. Line dry. Metallic and plastic parts can be hand washed with warm water and neutral soap. Do not use aggressive substances. IMPORTANT: Do not use solvents or bleach which can damage materials. This product is covered for 1 year from the date of purchase from any manufacturer’s defect. Please retain your receipt as a proof of purchase. If the repairs carried out on warranty would not be satisfactory and the item would not keep the best conditions, the guarantee holder would have the right to replace the purchased item by another one in similar characteristics or the devolution of the paid price. Babyhome reserves the right to fix or replace a defective item at its sole discretion. Warranty is voided if the item has been repaired or manipulated by non-authorized personnel. WARRANTY WASHING INSTRUCTIONS5 To avoid any risk, remove the protective plastics before use. They must be destroyed or out of the reach of the baby. If someone else must take care of the baby, explain him/her the instructions for use and safety. When the child can sit down, kneel down or stand up by himself, cot must not be used by this child anymore. Do not use this product if some part breaks or gets lost. Before using the cot, check that block mechanisms are locked and adjusted correctly. All assembly fittings should always be tightened properly and that care should be taken that no screws are loose, because a child could trap parts of the body or clothing (e.g. strings, necklaces, ribbons for babies’ dummies, etc), which would pose a risk of strangulation. Product must always be on the floor and over a safe and flat surface. Do not allow any other children to play nearby the cot without an adult’s vigilance In case of leaving baby without vigilance, it is necessary to use block position. The thickness of the mattress chosen shall be such that the vertical internal height (surface of the top of the mattress to the upper edge of the bed sides) is a least 200mm in the highest position of the bed base. - In gaps between extra padding and side of the bassinet / cradle. - On soft bedding Use only the pad provided by manufacturer. NEVER add a pillow, comforter, or another mattress for padding. SUFFOCATION HAZARD Infants have suocated6 Use just sold or approved accessories. Use just recommended spare parts. Pay attention to the eventual risk of fire and other important sources of heat, as central heating or gas heaters nearby the cot. The grey line drawn on the inner wall of the product marks the height of the mattress. WARNING! Failure to follow these warnings and the instruction could would results in serious injury or death FALL HAZARD - To help prevent falls, do not use this product when the infant begins to push up on hands and knees or has reached 9 kg. weight, whichever comes first. To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep, unless otherwise advised by your physician. If a sheet is used with the pad, use only the one provided by the bassinet or cradle manufacturer or one specifically designed to fit the dimension of the bassinet or cradle mattress. Strings can cause strangulation! Do not place items with a string around a child's neck, such as hood strings or pacifier cords. Do not suspend strings over a bassinet or cradle or attach strings to toys.

INSTRUCTIONS FOR ASSEMBLY AND USE

All the components can be found in the packing To assemble the structure, the most convenient is to put component A on the floor. Then, join cot’s legs to the direction shown in picture 1. To assemble each leg correctly it is necessary to push the buttons situated in both join pieces, according to detail of picture 1. Make sure the unblock systems are as in the picture; after assembling this piece will be situated to the left. The next step is to assemble the fabric. Fabric will be introduced into the metal structure until the base is supported on join axis between legs. Fabric gets fixed to upper structure closing the 4 zips at the perimeter of the textile, according to picture 3. Subsequently, you should close the safety locks located under the fabric with the aluminum bar. Image 4 refers to it with more detail. List and description of components: Main structure (A) Legs Textile Outside fabric: polyester 600D Inside fabric: cotton 100% Fitted Sheet: cotton 100% To take to pieces, remind to remove all the fixation elements and safety locks. This cot has 3 use positions: 4 wheels, stop and rock. Stop and rock positions are blocked. To change them, release the safety lock by moving the handle at the leg’s upper side. It is shown at the pictures below. To change from 4 wheels position to stop position, put foot over the revolving legs and spin it following the arrows in picture 5. To change from Stop position to rock position proceed the same way than before (picture 6). Before spinning the leg, make sure block is released by means of each’s leg side handle. In picture 7 it is shown how to put back the block position, from rock’s one. In this case, put foot under the revolving leg and spin it following the arrows in picture. Start position is blocked, so before spinning, lift the handle to release this movement. To get the 8 wheels position again, proceed in the same way than before (picture 8). Use also the side handle to unlock this position. NOTE: all movements before described can be done by hand7 CONSERVAR PARA FUTURAS CONSULTAS. LEER DETENIDAMENTE ESTE MANUAL DE INSTRUCCIONES PARA GARANTIZAR LA MÁXIMA SEGURIDAD DEL NIÑO.COMPROBAR EL FUNCIONAMIENTO DEL ARTÍCULO SIN NIÑO ANTES DE USARLO. IMPORTANTE