Curv - Lighting in-lite - Free user manual and instructions
Find the device manual for free Curv in-lite in PDF.
| Product Type | Outdoor LED wall light |
| Brand | in-lite |
| Model | Curv |
| Category | Outdoor lighting |
| Power supply | 12 V (low voltage system) or 100-240 V via separate transformer |
| Light source | High-quality LED |
| LED lifespan | Approximately 50,000 hours |
| Power | 2 W |
| Dimensions (L x H x D) | 300 x 50 x 5 mm |
| Housing material | Aluminium |
| Lens material | High-quality plastic |
| Package contents | 1 x Curv, 3 screws, 3 wall plugs, 1 Easy-Lock connector |
| Main functions | Decorative lighting for entrance doors, garden doors, terrace, sheds, fences |
| Installation | Wall mounting with drilling, screwing and connection to 12 V cable or transformer |
| Connector | Easy-Lock for connection to main cable |
| Protection | Clip-on protective cover |
| Maintenance and cleaning | Clean at least once a year with a clean cloth and warm water |
| Safety | Use only with in-lite 12 V system or suitable transformer; cut off power before maintenance |
| Warranty | Void if used with non-in-lite products |
| Repairability | Integrated LED light source not replaceable; spare parts available from distributor |
Frequently Asked Questions - Curv in-lite
User questions about Curv in-lite
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Lighting in PDF format for free! Find your manual Curv - in-lite and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Curv by in-lite.
USER MANUAL Curv in-lite
High quality plastic lens
Please read the following instructions before installing. You are advised to keep these installation instructions in a safe place.
Although a 12 V system is safe, we advise you to have a qualified electrician check the installation.
Use
Wall-mounted light fixture for installation near the front or back door, shed or fence, etc.
Lamp
The fixture is equipped with a high-quality LED lamp. These lamps have a long life (about 50,000 hours) and a high light output and their power consumption and the heat produced are extremely low.
#
Important!
Never connect the low-voltage cable directly to a 100-240 V power source. It is only suitable for use in combination with a 12 V low-voltage system. This product should only be used within the in-lite system. Use of products other than those made by in-lite will invalidate the warranty.
Enjoy the lighting in your yard.
EN
Connecting the fixture to 12 V
Step 1
Mark the position of the three attachment holes and the cable hole (A) in the wall plate on the wall. Make a hole for the cable of at least 13 mm at the location of the cable hole. Attach the wall plate to the surface using the screws supplied and plugs if necessary. (Fig. 1)
Step 2
Pass the 12V cable through the hole. Ensure that the two clamps for the covering plate (B) are free of cable. Then slide the covering plate over the wall plate until it clicks into place. (Fig. 2)
Step 3
Join the Easy-Lock connector to the main cable. (Fig. 3)
a. Clamp the cable duct on top of the main cable.
b. Place the cable duct (with the cable at the bottom) in the EasyLock connector.
c. Tighten the threaded cap on the Easy-Lock connector. This will cause the contacts to be pushed through the insulation on the cable. In tightening the cap, a little gel is applied to the contacts in the Easy-Lock connector. This serves to protect the contacts against moisture. A little gel may possibly come out of the Easy-Lock connector: so after installation (and/or before a meal), wash your hands with soap and water, and avoid the gel coming into contact with your eyes.
Step 4
Connect the main cable to the fixture by connecting the mini-connector. (Fig. 4)
If the lamp does not work correctly, check that the Easy-Lock connector is properly connected to the main cable. Do the same for the mini-connector. Repeat steps 3 and 4. When the fixture is connected to the main cable also check that the contacts of the Easy-Lock connector are not bent. If you have any problems, contact your dealer.
General maintenance advice
We advise wiping the fixture down at least once a year using a clean cloth and warm water.
EN
Connecting the fixture to 100-240 V
If you want to connect the fixture to a 100-240 V power source, you must use the separately available internal transformer. Your dealer can advise you about this. The appliance should only be connected to a 100-240 V power source by an authorised installer.
Step 1
Mark the position of the three attachment holes and the cable hole (A) in the wall plate on the wall. Make a hole for the cable of at least 13 mm at the location of the cable hole. Attach the wall plate to the surface using the screws supplied and plugs if necessary. (Fig. 1)
Step 2
Position the transformer in the fixture and then fix it in place using the supplied screw. Make sure that you place the screw in the opening with the metal ring (safety earthing) on the side of the 100-240 V power cable. (Fig. 1a)
Step 3
Connect the 100-240 V power cable from the transformer to the connecting block (C) in the wall plate. (Fig. 1b)
Step 4
Connect the internal transformer to the fixture by connecting the minicnector. (Fig. 1b and Fig. 4)
Step 5
The appliance should only be connected to a 100-240 V power source by an authorised installer. See the manual that accompanies the internal transformer.
Step 6
Ensure that the two clamps for the covering plate (B) are free of cable. Then slide the covering plate over the wall plate until it clicks into place. (Fig. 2)
General maintenance advice
We advise wiping the fixture down at least once a year using a clean cloth and warm water.
#
Important!
Before starting maintenance switch off the power.
DE
Inhalt
1x CURV 12 V/2 W
Abmessungen 300 × 75 × 150 ~mm
3x Schrauben
3xDubel
1x Easy-Lock
Material
Aluminium-Gehäuse
