TE615209RW - Coffee machine SIEMENS - Free user manual and instructions

USER MANUAL TE615209RW SIEMENS

• Contents Dear Co󰀨ee Connoisseur, Congratulations on purchasing this fully automatic co󰀨ee machine from Siemens. This instruction manual describes a number of versions of the appliance with minor di󰀨erences. Please also take note of the enclosed Quick reference guide, which you can then keep in the specially provided compartment 16 until you need it again. How to use these instructions: You can open up the front cover of this instruction manual to see illustrations of the appliance with each part numbered. These numbers will be referred to throughout the text. Example: brewing unit 14 These instructions also show display texts and symbols in a special way so that you can clearly see where we refer to texts displayed by the appliance or symbols that are marked on it. Example of display texts: Espresso Example of control elements: C Intended use 27 Important safety information 27 Included in delivery 29 Overview29 Overview of control elements 30 Display 31 Initial use 32 Childproof lock 33 Preparing drinks 33 Preparing co󰀨ee drinks p. 35
• Preparation using milk p. 35
• Preparation using ground co󰀨ee p. 36
• Dispensing hot water p. 36
• Adjusting the grind setting p. 36
• Menu 37 Care and daily cleaning 39 Cleaning the milk system p. 40
• Cleaning the brewing unit (Figure G) p. 41
• Service programmes 42 Cleaning the milk system p. 42
• Descaling p. 43
• Cleaning p. 43
• calc‘nClean Tips on energy saving 45 Frost protection 45 Storing accessories 45 Accessories 45 Disposal45 Guarantee 45 Simple troubleshooting 46 Technical specications 4827 p. 44

Intended use Intended use This appliance is intended for domestic use only. Only use the appliance indoors at room temperature and up to 2000 m above sea level. Important safety information Please read and follow the operating instructions carefully and keep them for later refer- ence! Enclose these instructions when you give this appliance to someone else. This appliance can be used by children aged from 8 years and above and by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervi- sion or instruction concerning use of the appliance in a safe way and if they understand the hazards involved. Keep children under 8 years of age away from the appliance and connecting cable and do not allow them to use the appliance. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children unless they are older than 8 years and supervised. Intended use Important safety information28 en Important safety information W Warning Risk of electric shock! ■ The appliance may only be connected to a power supply with alternating current via a correctly installed socket with earthing. Ensure that the protective conductor system of the domestic supply has been correctly installed. ■ Connect and operate the appliance only in accordance with the speci cations on the rating plate. ■ Do not use the appliance if the power cord and/or appli- ance are damaged. ■ Only our customer service may repair the appliance, e.g. by replacing a damaged power cord, in order to avoid hazards. ■ Never immerse the appliance or mains cord in water. ■ If there is a fault, pull out the mains plug immediately or switch o󰀨 the power supply. W Warning Hazard due to magnetism! The appliance contains perma- nent magnets which can a󰀨 ect electronic implants such as pacemakers or insulin pumps. Persons wearing electronic implants must maintain a minimum distance of 10 cm from the appliance and from the following parts upon removal: milk container, milk system, water tank and brewing unit. W Warning Risk of su󰀨 ocation! ■ Do not allow children to play with packaging material. ■ Store small parts safely as they can be easily swallowed. W Warning Risk of injury! ■ Do not reach into the grinding unit! ■ Improper use of this appliance may result in injury. W Warning Risk of burns! ■ The milk system becomes extremely hot. After use, always let it cool down before you touch it. ■ After use the surfaces of the heating element or hotplate can remain hot for some time.29

Included in delivery 1 Mains switch J 2 Control panel (see next page) 3 Display 4 Drinks outlet (co󰀨ee, milk, hot water), height-adjustable a) Cover b) Milk system /co󰀨ee outlet (two-part) c) Milk tube d) Suction pipe 5 Removable water tank 6 Lid for water tank 7 Storage compartment for measuring spoon 8 Measuring spoon (insertion aid for water lter) 9 Bean container 10 Aroma cover 11 Dial selector for grinding level 12 Drawer (for ground co󰀨ee/cleaning tablet) 13 Door to brewing unit 14 Brewing unit a) Locking mechanism b) Cover 15 Eject lever 16 Storage compartment for quick reference guide 17 Drip tray a) Drip tray panel b) Drip plate c) Co󰀨ee grounds container d) Floater * 18 Compartment for power cord 19 Rating plate (E number, FD)

• These user instructions describe a number of appliance versions. Items marked * are not present in all models. Overview (Figures B, C, D, E, F and G on the fold-out pages) Included in delivery (Figure A on the fold-out pages) a Fully automatic co󰀨ee machine b User Manual c Quick reference guide d Milk tube and suction pipe e Water hardness testing strip f Measuring spoon g Water lter

h Milk container with “freshLock” lid

i Descaling tablets *30 en Overview of control elements Overview of control elements (Figure B on the fold-out pages) The following symbols are visible or backlit depending on the appliance’s current operating mode:Espresso Caffe LatteCoffee Milk frothCappuccino Warm milkLatte Macchiato Hot waterstart stop C – Start/stop button I – Selection downF – Back menu A – Open menuG – Dispense two cups simultaneously B – Conrm / StoreH – Set co󰀨ee strength

D – Select cup size milk clean E – Service program for milk system (touch briey) and childproof lock (touch for at least 3 seconds).31

Display Mains switch J The mains switch J is used to switch the appliance on or o󰀨. The appliance rinses itself automatically when it is switched on and o󰀨. The appliance does not rinse if: ● it is still warm when switched on, or ● no co󰀨ee was dispensed before it was switched o󰀨. The appliance is ready for use when the symbols and the display on the control panel are lit. Control panel (touch eld) In the control panel you can easily navigate the controls just by touching the symbols and characters. You will hear an audible signal. These audible signals can be switched on or o󰀨 (see the section “Menu – Key tones”). Drink selection Touching the corresponding symbol selects the desired drink (see the section “Preparing drinks”). Start/stop button Touching C either begins preparing a drink or launches a service programme. If you touch C again while the drink is being prepared, dispensing will be prematurely halted. Menu Touching A calls up the menu, the navigation symbols will be activated and light up. Touch I, B and F to navigate through the menu and call up information or change settings (see the section “Menu”). Drink options Touching H or D adjusts the strength or size of the drink, touching G prepares two cups simultaneously as soon as you touch C to begin dispensing (see the section “Preparing drinks”). milk clean and childproof lock Briey touching E calls up the cleaning programme for the milk system (see the section “Daily maintenance and cleaning – Cleaning the milk system”). Touching E for 3 seconds or more activates or deactivates the childproof lock (see the section “Childproof lock”). Display The display shows the selected drinks and settings plus messages reporting the appliance’s operating status. Espresso regular medium Please refill water tank These messages are cleared as soon as the action has been carried out.32 en Initial use Initial use General Fill the appropriate container using only pure, cold, uncarbonated water and solely roasted beans. Do not use co󰀨ee beans that have been glazed, caramelised or treated with other additives containing sugar, since they will block the brewing unit. The water hardness setting on the appliance can be adjusted. The factory setting for the water hardness is 4. Use the enclosed test strip to determine the hardness of your water supply. If this shows a value other than 4, you will need to programme the appliance appropriately after it has been taken into service (see section “Menu – Water hardness”). Setting up the appliance ● Remove any protective plastic lm. ● Place the fully automatic co󰀨ee machine on a level, waterproof surface that is able to support its weight. ● The appliance’s ventilation slits must not be covered or obscured.

Important: Only use the appliance in a frost-free room. If it has been transported or stored at temperatures below 0°C, wait at least 3 hours before taking it into operation. ● Connect the power supply (cable storage compartment 18) to the socket. You can adjust the length of the cable by pulling it further out or pushing it back in. To do this, place the appliance with its back ush with the edge of the work surface and either pull the cable out downwards or push it in upwards. ● Flip up the lid of the water tank 6. ● Remove the water tank 5, rinse it out and ll it with fresh cold water. Do not ll it past the “max” mark. ● Replace the water tank 5, making sure that it is straight, and push it right down into place. ● Reclose the lid of the water tank 6. ● Fill the bean container 9 with co󰀨ee beans. ● Use the main switch J 1 to switch on the appliance. The control panel and the display will be activated. The display will show the previously specied language, which will also be used for all subsequent display texts. A number of di󰀨erent languages are available. ● Touch I repeatedly until the display indicates the desired language. Deutsch English Français ● Touch C to conrm your selection. The chosen language is now stored. The brand logo will light up on the display 3. The appliance will heat up and rinse itself, a small amount of water will run out of the drink outlet 4. The appliance is ready for use when the symbols and the display on the control panel are lit.

The factory settings of the fully automatic coffee machine are programmed for optimal perfor- mance. The appliances switches off automatically after a configured time (see the section “Menu – Automatic shut-down”).33

When the appliance is used for the first time, after a service program has been run and when it has not been operated for a long period, the first beverage will not have the full aroma and should not be consumed.

When the fully automatic coffee machine is first used, you will achieve a suitably thick and stable “crema” only after the first few cups have been dispensed.

If the appliance is in use for a long period of time, water droplets will form on the ventilation slits. This is normal. Childproof lock The appliance can be locked to protect children against scalding and burns. ● Touch E for at least 3 seconds. A key symbol appears on the display 3. The childproof lock is now active. It is no longer possible to operate the appliance. ● Touch E for at least 3 seconds. The key symbol disappears from the display 3. The childproof lock is now deactivated. The appliance can be used in the usual way. Preparing drinks This fully automatic co󰀨ee machine grinds fresh beans for every brewing. For optimum quality, store the beans in a cool place in sealed containers.

Important: Fill the water tank 5 with fresh clean water every day. The tank 5 should always contain sufficient water for operating the appliance.

Cups should be prewarmed, e.g. with hot water. This applies particularly to small thick-walled espresso cups.

For a number of settings, coffee is prepared in two stages (see “ aromaDouble Shot”). Please wait until the process is completely finished. Di󰀨erent beverages can be prepared just by touching a key. Drink selection Touching the appropriate symbol selects the desired drink. Your selection is indicated by lines above and below the symbol. The name of the drink and the currently active values for strength and cup size are shown in display 3. You can choose from the following drinks: Espresso Caffe Latte Coffee Milk froth Cappuccino Warm milk Latte Macchiato Hot water34 en Preparing drinks Adjusting the strength, selecting ground co󰀨ee Touch H to set the strength of your co󰀨ee individually or to specify that ground co󰀨ee is to be used. The following settings are possible: very mild very strong mild doubleshot strong regular doubleshot strong+ strong Ground coffee ● Touching the appropriate symbol selects the desired drink. ● Touch H repeatedly until the desired setting e.g. strong or Ground coffee (see the section “Preparation using ground co󰀨ee”) appears on the display. aromaDouble Shot The longer the co󰀨ee is brewed, the more bitter substances and undesired aromas are released. This has a negative e󰀨ect on the taste and makes the co󰀨ee less easily digestible. So for extra strong co󰀨ee, the appliance has a special aromaDouble Shot function. When half the quantity has been prepared, it grinds and brews fresh co󰀨ee beans so that only the pleasant, aromatic scents are released.

The aromaDouble Shot function can be selected for any drink containing a proportion of at least 35 ml coffee volume. It is not available for small drinks such as a small espresso or when the G setting is enabled. Select cup size Touching D selects the volume of co󰀨ee desired. The following settings are possible: small medium large ● Touching the appropriate symbol selects the desired drink. ● Touch D repeatedly until the display indicates the desired setting.

An arrow or multiple arrows next to the setting, e.g. „large ˆ”, indicate that the preset capacity (see the section “Menu – Set cup size”) has been changed. Two cups at once Once you have selected a black co󰀨ee or milky co󰀨ee drink (for some appliances, this applies only to black co󰀨ee), touching G prepares two cups simultaneously as soon as you touch C to begin dispensing. The setting is shown on the display. ● Touching the appropriate symbol selects the desired drink. ● Touch G. ● Place two prewarmed cups at left and right underneath the beverage outlet 4. ● Touch C to begin dispensing the beverage. The selected drink will be brewed and will then be dispensed into the two cups.

The drink is prepared in two stages (two grinding operations). Please wait until the process is completely finished.

Depending on the type of appliance: The function “Two cups at once” may be available only for black coffee, not for milky coffee drinks.35

Preparing drinks Preparing co󰀨ee drinks The appliance must be ready for use. ● Place a prewarmed cup underneath the beverage outlet 4. ● Touch the appropriate symbol to select the desired drink, Espresso or Coffee. The name of the drink and the currently active values for strength and cup size are shown in display. Coffee regular medium

You can change the cup size and coffee strength by touching D and H. If you select Ground coffee, follow the procedure described under “Preparation using ground coffee”. For example: ● Touch D repeatedly until the display shows large. ● Touch H repeatedly until the display shows mild. ● Touch C to begin dispensing the beverage. The co󰀨ee is brewed and then dispensed into the cup.

You can touch C again to prematurely halt dispensing. Preparation using milk This fully automatic co󰀨ee machine possesses an integrated milk system that enables you to prepare co󰀨ee with milk or milk froth or warm milk alone.

Risk of burns! The upper and lower sections of the milk system 4b become extremely hot. After use, always let them cool down before you touch them.

Caution! Dried milk residues are difficult to remove, so you should always clean the appliance after each use (see the section “Cleaning the milk system”).

While milk is being prepared you may hear a whistling sound. This is due to the technical nature of the milk system 4b.

Touch C again to prematurely halt dispensing. The appliance must be ready for use. The milk tube and suction pipe must be connected. ● Insert the suction pipe 4d into the milk container. ● Place a prewarmed cup or glass under- neath the beverage outlet. Co󰀨ee-based drinks with milk ● Touch the appropriate symbol to select Caffe Latte, Latte Macchiato or Cappuccino. The name of the drink and the previously specied values for strength and cup size are shown in display.

You can change the cup size and coffee strength by touching D and H. If you select Ground coffee, follow the procedure described under “Preparation using ground coffee”. ● Touch C to begin dispensing the beverage. The milk or milk froth is dispensed into the cup or glass rst. Then the co󰀨ee is brewed and runs into the cup or glass. You can touch C again to prema- turely halt dispensing of the milk or co󰀨ee, touching C twice stops the entire dispensing process.36 en Preparing drinks Milk froth or warm milk ● Touch the appropriate symbol to select Milk froth or Warm milk. ● Touch C to begin dispensing the beverage. Milk froth or warm milk is dispensed from the beverage outlet. Preparation using ground co󰀨ee This fully automatic co󰀨ee machine can also be operated using ground co󰀨ee (but not instant co󰀨ee).

When using ground coffee, the setting for the strength of the coffee, dispensing two cups at once and aromaDouble Shot is not available. The appliance must be ready for use. ● Place a prewarmed cup underneath the beverage outlet 4. ● Touch the appropriate symbol to select a black or milky co󰀨ee drink. ● Touch H repeatedly until the display shows Ground coffee. ● Open the ground co󰀨ee drawer 12. ● Place no more than two level measuring spoons of ground co󰀨ee in the drawer.

Caution! Do not place co󰀨ee beans or instant co󰀨ee in this drawer. ● Close the ground co󰀨ee drawer 12. ● Touch C to begin dispensing the beverage. The co󰀨ee is brewed and then dispensed into the cup.

Touch C again to prematurely halt dispensing. Dispensing hot water Before hot water is dispensed the milk system should be cleaned and the milk tube removed (see the section “Cleaning the milk system”). If the milk system is not cleaned small amounts of milk may be dispensed together with the hot water.

Risk of burns! The milk system 4b becomes extremely hot. After use, always let them cool down before you touch them. The appliance must be ready for use. ● Place a prewarmed cup underneath the beverage outlet 4. ● Touch the symbol for Hot water. ● Touch C to begin dispensing the beverage.

If you see the message Please remove suction hose, proceed as follows: ● Take o󰀨 the milk tube 4c and then touch C again. Hot water will ow out of the outlet 4.

Touch C again to prematurely halt dispensing. Adjusting the grind setting You can use the rotary selector 11 to adjust the grind setting from coarse to ne.

Caution! Adjust the grind setting only while the grinding unit is running, otherwise you may damage the appliance.

Risk of injury! Do not reach into the grinding unit.37

Menu ● With the grinding unit running, adjust the selector 11 from ne (a: turn anticlock- wise) to coarse (b: turn clockwise). a b

The new setting will not become apparent until after the second cup of coffee.

For dark roast coffee beans, choose a finer grind, for lighter beans a coarser grind. Menu The menu is used for changing individual settings, accessing information and launching processes. ● Touch A to open the menu. In the display you will see the various setting options, the navigation symbols light up. The current setting is marked on the display. Navigating through the menu: I = move down B = conrm / store F = go back A = open the menu / exit from the menu

Touching I displays each setting or selection option in order. After you reach the lowest menu item the topmost one is shown again. For example: Setting the co󰀨ee temperature to max. : ● Touch A. The menu is opened. ● Touch I repeatedly until the display shows Coffee temperature. ● Touch B, the display shows e.g. high. ● Touch I repeatedly until the display shows max. ● Touch B to store the setting. The display shows the conrmation. ● The menu item Coffee temperature appears. ● Touch F to exit from the menu. You can specify the following settings: Set cup size Set up the volume dispensed for each drink and each size of cup. The volumes set up in the factory can be adjusted stepwise. ● Use I to choose a drink and touch B to confirm your choice. ● Use I to choose the desired volume and touch B to confirm your choice. The setting is then saved. Languages Setting up the language to be used for display texts. ● Use I to choose the desired language and touch B to confirm your choice. Water hardness Set this to the hardness of the local water supply. Level 1, 2, 3, 4 or Softening system can be selected. The preset level of water hard- ness is level 4. ● Use I to choose the desired water hardness and touch B to confirm your choice.

It is important to set the water hard- ness correctly, so that the appliance indicates accurately when the descaling programme should be run.38 en Menu You can check the water hardness using the enclosed test strip or by asking your local water supplier. If a water softening system is installed in the house, please select the Softening system setting. ● Briey dip the test strip in the water and check the result after one minute. Level Water hardness German (°dH) French (°fH)

1-7 8-14 15-21 22-30 1-13 14-25 26-38 39-54 Automatic shut-down Setting how long the appliance should wait after the last drink was prepared before it automatically switches itself o󰀨. You can specify values from 15 minutes to 8 hours. The factory setting is 30 minutes. ● Use I to choose the desired interval and touch B to confirm your choice. Coffee temperature Specifying the temperature for co󰀨ee drinks and hot water. You can choose normal, high, or max. The setting applies to all types of drink preparation. ● Use I to choose the desired temperature level and touch B to confirm your choice. Water filter Specifying whether a water lter should be activated or whether no lter is used. You can choose Activate new filter or No filter.

Using a water filter can prevent the build-up of limescale. Water lters are available from retail outlets or from customer services (see the section “Accessories”).

Important: Before you can use a new water filter it will need to be rinsed. ● Use the measuring spoon 8 to press the water lter rmly into the water tank 5. ● Fill the water tank with water up to the “max” mark. ● Connect the milk tube 4c to the milk system 4b and the suction pipe 4d. ● Insert the end of the suction pipe 4d into the drip plate 17b. ● Touch A and use I to select Water filter. ● Touch B and use I to select Activate new filter. ● Empty the drip tray and re-insert. ● Touch B to conrm. Water will now ow through the lter to rinse it. ● Then empty the drip tray and re-insert. The appliance is ready for use again.

Rinsing the filter simultaneously activates the setting for displaying the message “Please change water filter”. When this message appears, or at the latest after two months, the lter will no longer be e󰀨ective. It needs to be replaced for reasons of hygiene and to prevent a build-up of limescale (which could damage the appliance). If you do not intend to insert a new lter, select the setting No filter and touch B to conrm.39

Care and daily cleaning

If the appliance has not been used for a prolonged period (for example, while you are on holiday), the existing filter should be rinsed before the appliance is used again. To do this, simply dispense a cup of hot water. Cleaning and care Starting the special service programmes. You can select Rinse the milk system, Descale, Clean or calc’nClean. ● Use I to choose the desired programme and touch B to confirm your choice. ● Touch C to begin running the programme.

Important: Be sure to take note of the section on “Service programmes”. Info Service programmes (depending on the type of appliance) Display how many beverages can still be prepared before it will be necessary to run one of the service programmes. ● Use I to display Clean after --- c or Descale after --- c. ● Touch F to exit from the display.

For technical reasons the counter does not represent a precise number of cups. Frost protection Service programme to prevent frost damage during transportation and storage. This programme completely empties the appliance.

The appliance must be ready for use and the water tank 5 must be filled. ● Touch C to begin running the programme. ● Remove the water tank; the appliance automatically empties all its pipes and then switches itself o󰀨. ● Empty the water tank 5 and the drip tray 17. Key tones Switches on or o󰀨 the tones that you hear when you touch the control panel. ● Touch B to confirm your choice. ● Use I to choose Key tones ON or Key tones OFF and touch B to confirm your choice. Beverage statistics (depending on the type of appliance) Shows the volume of drinks dispensed since the appliance was taken into service. ● Touch F to exit from the display. Factory settings Resets your own settings to the condition when delivered. ● Touch C to clear all your own settings. Care and daily cleaning

Risk of electric shock! Before cleaning the appliance, unplug it from the mains. Never immerse the appliance in water. Do not use a steam cleaner. ● Wipe the outside of the appliance with a soft, damp cloth. ● Clean the control panel with a microbre cloth. ● Do not use any cleaning agents containing alcohol or spirits. ● Do not use abrasive cloths or cleaning agents.40 en Care and daily cleaning ● Always immediately remove any lime- scale, or residues of co󰀨ee, milk, cleaning or descaling solution. It is possible for corrosion to form underneath such deposits. ● New sponge cloths may contain salts that can cause rust lms to form on stainless steel, so such cloths should always be thoroughly rinsed before use. ● Pull the drip tray 17 and co󰀨ee grounds container 17c towards the front and remove them. Take o󰀨 the panel 17a and drip plate 17b. Empty and clean the drip tray and co󰀨ee grounds container. ● Wipe out the inside of the appliance (holder, trays) and the drawer for ground co󰀨ee (this cannot be removed). ● Remove the oat 17d and clean it with a moist cloth (depends on the type of appliance).

Do not put the following parts in the dishwasher: Panel of drip tray 17a, cover 4a, brewing unit 14, water tank 5 and aroma cover 10.

The following parts may be cleaned in the dishwasher: Drip tray 17, drip plate 17b, co󰀨ee grounds container 17c, measuring spoon 8 and the upper and lower parts of the milk system 4b.

Important: The drip tray 17 and coffee grounds container 17c should be emptied and cleaned every day in order to prevent deposits.

If the appliance is cold when switched on, or if it is switched off after dispensing coffee, it rinses auto- matically. The system is therefore self-cleaning.

Important: If at any time the appli- ance is not used for a lengthy period (e.g. holiday), clean the entire appli- ance thoroughly, including the milk system 4b and brewing unit 14. Cleaning the milk system

Be sure to clean the milk system 4b every time you make a drink involving milk! You can clean the milk system 4b automati- cally using programme E or by hand. Automatic cleaning: ● Touch E and then R. ● Place an empty glass under the beverage outlet 4 and stand the end of the suction pipe 4d in it. ● Touch C to begin running the programme. The milk system 4b will now clean itself automatically. ● Then empty the glass and clean the suction pipe 4d. Cleaning by hand:

Risk of burns! The milk system 4b becomes extremely hot. After use, always let them cool down before you touch them. Take the milk system 4b apart to clean it: ● Push the beverage outlet 4 right down. ● Take o󰀨 the cover 4a towards the front and pull o󰀨 the milk tube.41

Care and daily cleaning ● Remove the milk system 4b by pulling it straight forward. ● Take apart the upper and lower parts of the milk system 4b. ● Separate the milk tube from the suction pipe. ● Clean the individual parts with washing- up liquid and a soft cloth. ● Rinse all parts with clean water and dry them.

The upper and lower parts of the milk system 4b, the milk tube 4c and the suction pipe 4d can also be cleaned in a dishwasher. ● Reassemble the individual parts. ● Place the milk system 4b back in the appliance from the front, making sure it is straight. ● Replace the cover 4a. Cleaning the brewing unit (Figure G)

See also the Quick reference guide in the storage compartment 16. In addition to the automatic cleaning programme, the brewing unit 14 should be removed regularly for cleaning. ● Use the main switch J 1 to switch the appliance completely o󰀨. ● Open the door 13 to the brewing unit. ● Slide the red latch 14a on the brewing unit 14 all the way to the left. ● Press the eject lever 15 right down. The brewing unit will be released. ● Take hold of the brewing unit 14 by the recessed grips and carefully remove it.

Important: Clean it without using washing-up liquid and do not put it in the dishwasher. ● Remove the cover 14b and thoroughly clean the brewing unit 14 under running water. ● Thoroughly clean the strainer of the brewing unit under the water jet.42 en Service programmes ● Thoroughly clean the inside of the appli- ance with a moist cloth, removing any co󰀨ee residues. ● Allow the brewing unit 14 and the inside of the appliance to dry. ● Replace the cover 14b on the brewing unit and then push the brewing unit 14 back into the appliance until it latches into place. ● Press the eject lever 15 right up. ● Slide the red latch 14a all the way to the right and close the door 13. Service programmes

See also the Quick reference guide in the storage compartment 16. Following prior notication, either Descaling necessary or Cleaning necessary or calc’nClean necessary. appears in display 3 at certain intervals. The unit should immediately be cleaned or descaled using the appropriate programme. The two processes Descale and Clean can optionally be carried out together using the calc’nClean function (see the section “calc’nClean”). Failure to carry out the service programme according to the instruc- tions may damage the appliance.

Important: if descaling is not performed on the appliance in good time, then the following appears: Descaling overdue. Appliance will soon be locked --> press menu for 3 sec. Immediately perform the descaling process in accordance with the instructions. If the appliance is locked, it can only be operated again once the descaling process has been carried out.

Caution! For each of the service programmes, use descaling and cleaning agents as described in the instructions. Never interrupt a service programme. Do not swallow any cleaning uids! Never use vinegar, citric acid or any vinegar-based or citric acid-based agents. Never place descaling tablets or other descaling materials in the co󰀨ee drawer 12! Before starting the service program (Descale, Clean or calc’nClean) remove the brewing unit, clean it as instructed and replace it. Specially developed suitable descaling and cleaning tablets are available from retail outlets or from customer services (see the section “Accessories”) Cleaning the milk system Takes about 1 minute. ● Touch A to open the menu. ● Use I to choose Cleaning and care and touch B to conrm your choice. ● Use I to choose Rinse the milk system and touch B to conrm your choice. ● Touch C to begin running the programme.

The milk system can also be cleaned by pressing E. The display 3 will indicate the progress of the programme: ● Place an empty glass under the beverage outlet 4 and stand the end of the suction pipe 4d in it. ● Touch C. The milk system will now clean itself automatically. ● Then empty the glass and clean the suction pipe 4d. You should also regularly clean the milk system manually (dishwasher or by hand).43

Service programmes Descaling Takes about 30 minutes. The line at the bottom of the display indicates the progress of the descaling process.

If there is a water filter in the water tank 5, be sure to remove it before starting the service programme. ● Touch A to open the menu. ● Use I to choose Cleaning and care and touch B to conrm your choice. ● Use I to choose Descale and touch B to conrm your choice. ● Touch C to begin running the programme. The display 3 will indicate the progress of the programme: ● Empty and re-insert the drip tray 17.

The following request appears: Remove water filter if inserted ¢start. ● Remove the lter and then touch C again. ● Pour lukewarm water into the empty water tank 5 up to the “05 l” mark and then dissolve one Siemens descaling tablet TZ80002 in it. ● Touch C. ● Place a container with a capacity of 0.5 litre under the beverage outlet 4. ● Place the end of the suction pipe 4d in the container. ● Touch C. The descaling programme will now run for about 20 minutes.

If there is not enough descaling solu- tion in the water tank 5, you will see the prompt Refill descaler ¢start. ● Add more descaling solution and then touch C again. ● Rinse the water tank 5 and rell it with fresh water up to the “max” mark. ● If you use a lter, replace it now. ● Touch C. The descaling programme will now run for about 1 minute and rinse the appliance. ● Empty and re-insert the drip tray 17.

Important: Wipe over the appliance with a soft damp cloth to ensure that you immediately remove any traces of descaling solution. It is possible for corrosion to form underneath such deposits. New sponge cloths may contain salts that can cause rust films to form on stainless steel, so such cloths should always be thoroughly rinsed before use. Clean the suction pipe 4d of the drinks outlet particu- larly carefully. The appliance has nished descaling and is ready for use again. Cleaning Takes about 9 minutes. The line at the bottom of the display indicates the progress of the descaling process. ● Touch A to open the menu. ● Use I to choose Cleaning and care and touch B to conrm your choice. ● Use I to choose Clean and touch B to conrm your choice. ● Touch C to begin running the programme. The display 3 will indicate the progress of the programme: ● Empty and re-insert the drip tray 17. ● Open the ground co󰀨ee drawer 12. ● Drop one Siemens cleaning tablet in the drawer 12 and close it. ● Touch C. The cleaning programme will now run for about 7 minutes.44 en Service programmes ● Empty and re-insert the drip tray 17. The appliance has nished cleaning and is ready for use again. calc‘nClean Takes about 43 minutes. calc’nClean combines the functions Descale and Clean. If both programmes are due to be carried out close together the fully automatic co󰀨ee machine will automatically suggest this service programme. The line at the bottom of the display indicates the progress of the descaling process.

If there is a water filter in the water tank 5, be sure to remove it before starting the service programme. ● Touch A to open the menu. ● Use I to choose Cleaning and care and touch B to conrm your choice. ● Use I to choose calc’nClean and touch B to conrm your choice. ● Touch C to begin running the programme. The display 3 will indicate the progress of the programme: ● Empty and re-insert the drip tray 17. ● Open the ground co󰀨ee drawer 12. ● Drop one Siemens cleaning tablet in the drawer 12 and close it. ● Touch C.

The following request appears: Remove water filter if inserted ¢start. ● Remove the lter and then touch C again. ● Pour lukewarm water into the empty water tank 5 up to the “05 l” mark and then dissolve one Siemens descaling tablet TZ80002 in it. ● Touch C. ● Place a container with a capacity of 1 litre under the beverage outlet 4. ● Place the end of the suction pipe 4d in the container. ● Touch C. The descaling programme will now run for about 28 minutes.

If there is not enough descaling solu- tion in the water tank 5, you will see the prompt Refill descaler ¢start. ● Add more descaling solution and then touch C again. ● Rinse the water tank 5 and rell it with fresh water up to the “max” mark. ● If you use a lter, replace it now. ● Touch C. The descaling programme will now run for about one more minute, and then the cleaning programme will run for about 7 minutes and rinse the appliance. ● Empty and re-insert the drip tray 17.

Important: Wipe over the appliance with a soft damp cloth to ensure that you immediately remove any traces of descaling solution. It is possible for corrosion to form underneath such deposits. New sponge cloths may contain salts that can cause rust films to form on stainless steel, so such cloths should always be thoroughly rinsed before use. Clean the suction pipe 4d of the drinks outlet particu- larly carefully. The appliance has nished descaling and is ready for use again.

Important: If any of the service programmes is ever interrupted, for instance by a power failure, please proceed as follows:45

Tips on energy saving ● Rinse the water tank 5 and rell it with fresh water up to the “max” mark. ● Touch C. The appliance will be rinsed for approx. 2 minutes for safety reasons. ● Empty and re-insert the drip tray 17. The aborted service programme must be restarted. Tips on energy saving ● When the fully automatic co󰀨ee machine is not in use, use the mains switch J 1 on the front of the appliance to switch it o󰀨. ● In the menu, set the Automatic shut-down period to 15 minutes. ● If possible, do not interrupt the dispensing of co󰀨ee or milk froth. Stopping a process prematurely results in higher energy consumption and the drip tray lls up more quickly. ● Descale the appliance regularly to avoid a build-up of limescale. Limescale residues cause higher energy consumption. Frost protection

Caution! To prevent frost damage during trans- portation and storage, completely empty the appliance beforehand. See the section “Menu – Frost protection”. Storing accessories The fully automatic co󰀨ee machine has special compartments to hold the meas- uring spoon and the Quick reference guide. ● To store the measuring spoon 8, lift o󰀨 the water tank 5 and place the spoon in the preformed recess 7. ● To store the Quick reference guide, open the door to the brewing unit 13 and insert the guide into the space provided 16. Accessories The following accessories are available from retailers or from customer service: Accessories Order number Retail / Customer service Cleaning tablets TZ80001 / 00311807 Descaling tablets TZ80002 / 00576693 Water lter TZ70003 / 00575491 Care set TZ80004 / 00576330 Milk container with “freshLock” lid TZ80009N / 00576166 Disposal

Dispose of packaging in an environ- mentally-friendly manner. This appliance is labelled in accordance with European Directive 2012/19/EU concerning used electrical and electronic appliances (waste electrical and electronic equipment – WEEE). The guideline determines the frame- work for the return and recycling of used appliances as applicable throughout the EU. Please ask your specialist retailer about current disposal facilities. Guarantee The guarantee conditions for this appliance are as de ned by our representative in the country in which it is sold. Details regarding these conditions can be obtained from the dealer from whom the appliance was purchased. The bill of sale or receipt must be produced when making any claim under the terms of this guarantee. Changes reserved.46 en Simple troubleshooting Simple troubleshooting Problem Cause Solution Co󰀨ee or milk froth quality varies considerably. Build-up of limescale in the appliance. Descale the appliance as described in the instructions. No hot water dispensed. The milk system or its holder is not clean. Clean the milk system or its holder (see the section “Cleaning the milk system”). Too little milk froth, or none at all, or the milk system is not taking in any milk. The milk system or its holder is not clean. Clean the milk system or its holder (see the section “Cleaning the milk system”). Milk not suitable for foaming. Do not use milk that has already been boiled. Use cold milk with a fat content of at least 1.5%. The milk system is incor- rectly assembled. Moisten the upper and lower sections and t them together. Build-up of limescale in the appliance. Descale the appliance as described in the instructions. The selected per-cup quantity is not reached. Co󰀨ee dispensing slows to a trickle or stops completely. Co󰀨ee is being ground too nely, or the pre-ground co󰀨ee is too ne. Adjust the grinding unit to a coarser setting. Use a coarser ground co󰀨ee. Heavy build-up of lime- scale in the appliance. Descale the appliance as described in the instructions. Co󰀨ee has no “crema”. Unsuitable type of co󰀨ee. Use a type of co󰀨ee with a higher proportion of robusta beans. The beans are no longer fresh. Use fresh beans. The grinding setting is not suitable for the beans. Adjust the grinding unit to a ner setting. Co󰀨ee is too “acidic”. The grinding setting is too coarse or the pre-ground co󰀨ee is too coarse. Adjust the grinding unit to a ner setting or use ner pre-ground co󰀨ee. Unsuitable type of co󰀨ee. Use a darker roast. Co󰀨ee is too “bitter”. The grinding setting is too ne or the pre-ground co󰀨ee is too ne. Adjust the grinding unit to a coarser setting or use coarser pre-ground co󰀨ee. Unsuitable type of co󰀨ee. Change the type of co󰀨ee. If you are unable to solve the problem, always call the hotline! You will nd the telephone numbers at the back of these instructions.47

Simple troubleshooting Problem Cause Solution The co󰀨ee tastes “burnt”. The brewing temperature is too high Reduce the temperature, see the section “Menu – Coffee temperature”. The grinding setting is too ne or the pre-ground co󰀨ee is too ne. Adjust the grinding unit to a coarser setting or use coarser pre-ground co󰀨ee. Unsuitable type of co󰀨ee. Change the type of co󰀨ee. The water lter does not stay in position in the water tank. The water lter is not mounted correctly. Firmly press the water lter straight down into the tank connection. The co󰀨ee grounds are not compact and are too wet. The grinding setting is too ne or too coarse, or not enough ground co󰀨ee has been used. Adjust the grinding unit to a coarser or ner setting, or use 2 level measuring spoons of ground co󰀨ee. Water dripped onto the inner oor of the appli- ance when the drip tray was removed. Drip tray was removed too soon. Wait a few seconds after the last drink was dispensed before removing the drip tray. Display shows Please refill bean container although the container is already full, or the grinder is not grinding any beans. Beans are not falling into the grinding unit (beans too oily). Gently tap the bean container. Possibly change the type of co󰀨ee used. When the bean container is empty, wipe it with a dry cloth. Display shows Please empty drip tray despite the drip tray being empty. Emptying is not detected when the appliance is switched o󰀨. When the appliance is switched on, remove and re-insert the drip tray. The drip tray is soiled. Clean the drip tray thoroughly. Display shows Refill with still water or change filter Water tank wrongly inserted. Insert water tank correctly. Carbonated water in the water tank. Fill the water tank with fresh tap water. Float is stuck in the water tank. Remove the tank and clean thoroughly. New water lter did not rinse according to the instructions. Rinse the water lter according to instructions and then switch on. Air in the water lter. Dip the water lter into water until no more air bubbles escape, replace the lter. Water lter is old. Insert a new water lter. If you are unable to solve the problem, always call the hotline! You will nd the telephone numbers at the back of these instructions.48 en Technical specications Problem Cause Solution Display shows Please clean brewing unit, then replace Brewing unit is soiled. Clean the brewing unit. Too much pre-ground co󰀨ee in the brewing unit. Clean the brewing unit. Place no more than two level measuring spoons of ground co󰀨ee in the drawer. The mechanism of the brewing unit is sti󰀨. Clean the brewing unit (see the section “Daily maintenance and cleaning”). Display shows Please restart appliance Appliance is too warm. Leave the appliance to cool down. Brewing unit is soiled. Clean the brewing unit. Display shows Descaling insufficient. Repeat process Incorrect or insu󰀩cient descaler or excessive scale existing on appliance. Perform descaling programme again. Display shows Please let appliance cool down Appliance is too hot. Switch o󰀨 appliance for 30 minutes. Display shows Error Please contact hotline The appliance has a fault. Please contact the hotline. If you are unable to solve the problem, always call the hotline! You will nd the telephone numbers at the back of these instructions. Technical specications Power connection (voltage – frequency) 220–240 V – 50/60 Hz Heater wattage 1500 W Maximum static pump pressure 15 bar (TE603) 19 bar (TE605 / TE607) Maximum water tank capacity (without lter) 1.7 l Maximum capacity of the co󰀨ee bean container ~300 g Length of power cable 100 cm Dimensions (H x B x D) 385 x 301 x 458 mm Weight, empty 10–12 kg Type of grinding unit Ceramic49