305W Elite - Pets Cat Mate - Free user manual and instructions

Frequently Asked Questions - 305W Elite Cat Mate

USER MANUAL 305W Elite Cat Mate

Super Selective LD.DISC CAT FLAP WITH

LD-MARKE KATZENKLAPPE MIT ZEITSCHALTUHR FUNKTION
CHATIÈRE DISQUE DIDENTIFICATION AVEC FONCTION DE TEMPORISATION
GATERA CON DISCO DE I.D. CON CONTROL DE TIEMPO
NL ID.DISCKATTENDEUR MET TNDKLOK FUNCTIONERING

© PET MATE Ltd · Lyon Road · Hersham · Surrey · KT12 3PU · England

N.America only:

Ani Mate 104A Longview Drive Conroe Texas 77301

www.pet-mate.com

30503-0115

±b www.pet-mate.com

[phone] N America [phone]

Pet Mate Ltd. guarantees your product for a period of 3 years from the date of purchase, subject to the registration of your purchase details on our website www.pet-mate.com within 14 days of purchase. (If you do not have access to a computer, please send details of your purchase with copy of receipt along with your name and address.) In the event of a fault developing contact Pet Mate customer services for a returns authorisation number. The manufacturer will be responsible for any arising due to faulty materials or manufacture. Any defective item will be repaired or replaced free of charge at the manufacturer's discretion, provided that the defect has not been caused by neglect, misuse or normal wear and tear. Your statutory rights are not affected.

GARANTIE

1. SET button
2. Microchip / I.D. Disc search indicator
3. INDIVIDUAL' lock setting indicator (Rel. 305 only)
4. Low battery indicator
5. AM/PM indicators (12Hr clock mode)
6. 'TIMER' function indicator
7. 'TIMER' mode 'Start/Finish' indicators
8. "TIMER" button
   9.4WAY' button
9. CAT 1 location symbol
10. CAT 2 location symbol
11. CAT 3 location symbol
12. PROGRAM' button (under battery cover)
13. 4WAY lock indicators
14. Alphanumeric display (normally states time)
15. ADVANCE' button

IMPORTANT - READ BEFORE USE

WICHTIG-BITTEVORVERWENDUNG

1. SET-Table
2. Mikrochtil D-Wankan
   SCHAVAGE
3. Average for INDIVIDUAL Value of total capitalization (in 10
   Net.365
   Betheranaeandanzeige
   5.AWPM-Azngn
   (12-Shnder-Lrrn

Seiten 12-19

fentheisbembei
MESTASTE
edckel

ganzelgr

eae Uerznege
5 Tasa

IMPORTANT-A LIRE AVANT USAGE

100
ACUMC H
Statement figure:

[Tab]

E IMPORTANTE-LEA ANTES DE USAR

1. Botoin SCT
2. Indecor de biquet de
   mecnhadnado 1.0
3. Indicate the use of these terms.
   INDIVIDUALR
   eckawenie
4. Indicador de pia doja

5. Indeces APV (in millions)
   ande anodrrcjcde 12 nore

6. Indicador de funcao 'TIMER'

7. Indicaedes de Startfinihern
   clmono TIMEN
8. Bank TIMBER
9. Union 4WAY
10. Simbo de la cuestion del
    QAT01
11. Sinboc da bacecon del
    GATO2

Paginas 28-35

1. SET knop
2. Zoekindcator mrochpi
   L.D. cteo
   3.INDIVIDUALS
   (ashrc)
   (Ref. 105)
   Lana bellnng

5.AMPM-1y080r(12-3)KcK

1. "TICKER' functor-Inducer
   TIMEN-StdExisEtxkster
   1、《关于（2017年限制性股票激励计划）及其摘要的议案》
2. TIMER loop
   A. 16 kpc times
3. 100
   10.KATIinssybnen

A
1
1. 实验原理
engereongindicator
dsdsysysoh
0001k1188

1. SFT Inap 6.TIMER' Functie Indlctor 12.KAT3 ccsaysbod
   2.Zoinkindor mchnp 7.TIMER- StarFshnH Indclator 13.PROGRMWA Inap (ndar deaklae balei)
2. INDIVIDUAL Vorgandling (dialkiv) 8.TIMER Inp 14.VAP Wergencngndoktor 15.Altomudere daysychoem 16.Gaet gewenik (kifse)
   4.Lage ballinndsoor 10.KAT 1 fataosybnol 11.KAT 2 fataosybnol 16.ADVANCE Inp

Contents

1. Introduction 4
2. Fitting the Batteries 5
3. Programming 5
4. Access Options 6

4.1 Setting access options 6
4.2 Setting INDIVIDUAL access options (2-9 Cats) 6
4.3 Setting timer control / lock for ALL cats 6

1. Fitting I.D. Disc(s) to Your Cat(s) 8
2. Viewing your cat(s) location 8
3. To view how long since the cat(s) last used the cat flap 8
4. Training Your Cat to Use the Cat Flap or if Your Cat Has Lost its I.D. Disc 8
5. Battery Replacement 9
6. Reprogramming a New I.D. Disc or Microchipped Cat 9
7. Factory Reset 9
8. Energy Saving Mode 10
9. Troubleshooting 10

1. Introduction

Thank you for choosing the Cat Mate Elite Cat Flap with Timer Control.

CAREFULLY READ THESE INSTRUCTIONS AND PROGRAM / TEST THE CAT FLAP BEFORE YOU INSTALL IT.

The Cat Mate Elite Cat Flap with Timer Control allows you to control up to 9 cats to have access to and from your property. Furthermore, it will allow you to monitor the movement of up to 3 individual cats: showing when your cat last entered or left the house, and how many hours since your cat last used the flap.

To ensure that your chosen settings cannot easily be tampered with, we have made the control buttons so that they need to be pressed firmly to operate.

If you wish to stop any task (except programming) at any stage, the system will time out after 60 seconds.

Settings will not be saved unless you press the 'SET' button.

The Microchip Cat Flap with Timer Control (Ref. 355) is suitable for all popular microchips. Alternatively it may be operated by an I.D. Disc (available separately).

You may wish to use an I.D. Disc for cats without a microchip or in the event that your cat's microchip is faulty or poorly positioned.

2. Fitting the Batteries

2.1 Remove the battery cover by pushing the battery cover upwards (see Fig. 2). The cover will snap off.
2.2 Insert 4 x AA (R6) batteries as shown (Fig. 3), by sliding the 2 end batteries in first.
2.3 The cat flap will self-check for up to 60 seconds after which only the IN & OUT arrows will be visible on the LCD display. The flap is ready to program.

You may use all popular batteries including rechargeable and lithium batteries but the 'BATTERY INDICATOR' will only work correctly with alkaline batteries. Good quality alkaline batteries should last approximately 12 months (depending on number of cats and usage).

3. Programming

The next step is to program the microchip or I.D. Disc belonging to each cat. We recommend that you now choose a number for your cat(s) and, if appropriate, mark it on the I.D. Disc label and on the table at the end of these instructions.

NOTE: The programming sequence is time sensitive and the LCD will revert to the normal display if each step is not completed within approximately 15 minutes.

In order for the flap to recognise your cat(s) microchip or I.D. Disc, you need to do the following:

3.1 Press and hold the 'PROGRAM' button on the circuit board for 5 seconds (Fig. 4) until the search indicator (Fig. 1) appears.
3.2 'CAT 1' and the number '1' will flash - there will be lines moving around the first TWO ZEROS'.
3.3 Place the front of the I.D. Disc in the tunnel opening (Fig. 5) or to program your cat's microchip, encourage your cat to slowly pass through the tunnel by holding the flap open as shown in Fig. 6.
3.4 When programmed, the 'TWO ZEROS' will disappear and 'Pr1' will flash.
3.5 Press the 'SET' button to save the setting
For additional cats, up to a maximum of 9, repeat steps 3.1 to 3.5.

4. Access Options

The access options available are shown below.

In & Out Your cat(s) can come in and out of the flap

In Only Your cat(s) can come in through the flap but cannot leave through the flap

'Out Only' Cat(s) can go out through the flap but cannot enter through the flap

'Locked' Cat(s) cannot use the flap

4.1 Setting Access Options for ALL Cats

If you wish ALL of your cats to have the same access option, e.g. you require ALL cats to be able to come in and go out of the flap, proceed as follows:

4.1.1 Press and hold the '4 WAY' button for 5 seconds until the display flashes.

4.1.2 Repeatedly press the '4 WAY' button to scroll through the available access options (Fig. 7), until you come to the one you want.

4.1.3 Press the 'SET' button to save the setting.

4.2 Setting INDIVIDUAL Access Options (2-9 Cats)

NOTE: This feature is only available on ID Disc Cat Flap with Timer Control (Ref. 305).

If you wish to assign an individual access option to each of your cats, e.g. to keep Cat 1 'LOCKED' in but allow Cat 2 'OUT ONLY', proceed as follows:

NOTE: This setting will not prevent a cat that is not allowed out following 'head to tail' another cat that is allowed out.

4.2.1 Press and hold the '4 WAY' button for 5 seconds until the display flashes.

4.2.2 Repeatedly press the '4 WAY' button until 'IND' appears on the LCD display.

4.2.3 Press the 'SET' button to save the setting.

4.2.4 Repeatedly press the '4 WAY' button until the required access option for Cat 1 is obtained.

4.2.5 Press the 'SET' button to save the setting.

4.2.6 Repeat 4.2.4 and 4.2.5 above for all of your cats with a programmed I.D. Disc.

NOTE: To see the individual settings you have made for your cat(s) at any time, press the '4 WAY' button for 1 second and release repeatedly.

4.3 Setting Timer Control/Clock for ALL Cats

If you wish to set your cat flap to ensure that ALL cats have a particular access option, over a selected timed period, e.g. to keep your cat(s) in at night between 19:00 and 06:00, you will first need to decide:

a) Which lock setting should apply DURING the timed period, (in the above example 'IN ONLY' will apply). Outside the timed period, the lock setting made in section 4.1 or 4.2 will apply.

b) When the timed period should 'START' (In the above example 19:00hrs).

c) When the timed period should FINISH' (in the above example 06:00hrs).

d) You will also need to know the current time.

Proceed as follows:

NOTE: if you do not press a button for more than 60 seconds the display will revert to normal and you will need to start again.

4.3.1 Press the 'TIMER' button for 5 seconds until the Timer function indicator flashes.

4.3.2 Repeatedly press the '4 WAY' button to select the required access options from: IN & OUT, IN ONLY, 'OUT ONLY', 'LOCKED' or 'OFF'.

4.3.3 Press the 'SET' button to save the setting.

4.3.4 The display will show time with the Minute symbol flashing. Repeatedly press the +2 button until the current Minutes setting is shown (i.e. 10 if the current time is 12:10).

4.3.5 Press the 'SET' button to save the setting.

4.3.6 The display will now show the time with the Hour symbol flashing. If you wish to change between a 24 hour clock and AM/PM setting, press the 'TIMER' button.

4.3.7. Repeatedly press the +1 until the correct Hour setting is shown (e.g. 12 if the current time is 12:10).

4.3.8. Press the 'SET' button to save the setting.

4.3.9. The display will show the word 'START' and the minutes will flash. Press the +' button until the desired minutes setting is shown, (in the above example '00'). Press the 'SET' button to save the setting.

4.3.10 Then set the hours in the same way (in the above example 19:00).

4.3.11 The display will show the FINISH' time. Set in the same way as the START' time. Remember to press 'SET' to save the setting.

When the Timer is set, the Timer function indicator (Fig. 1) will be shown on the display.

When the timed lock is active, the access option symbol chosen at 4.3.2 will flash slowly.

To check the time settings, briefly press the 'TIMER' button and release. The display will show the timed access option selected and the 'START' time. Press the 'TIMER' button again to show 'FINISH' time. The display will revert to current time after 5 seconds.

To cancel timer control and revert back to the normal access option:

4.3.12 Press the 'TIMER' button for 5 seconds.
4.3.13 Press the '4 WAY' button and go back through the options until you come to 'OFF'.
4.3.14 Press the 'SET' button 3 times to keep the current clock time and return to the normal display.

5. Fitting I.D. Disc(s) to your Cat(s)

5.1 If desired, record your cat's details on the I.D. label by writing on the label in pen and sticking the clear waterproof cover over the writing.
5.2 IMPORTANT: Attach the I.D. Disc directly to the collar, NOT from a ring attached to the collar) so that it is as high as possible and parallel to flap (as shown in Fig. 7).

We recommend the use of a fabric collar without large metal attachments (other name discs etc.).

6. Viewing Your Cat's Location

The LCD shows at a glance, the location of up to three cats (1-3).

The cat last went through the flap, coming into the house;

The cat last went through the flap, going out of the house.

Please note this display is only a guide to your cats' location. The cat flap determines the location of your cat by recording its last movement through the cat flap. The results may be misleading if the cat has an alternative entrance/exit to the house or if the cat has followed another cat through the cat flap; if it only puts its nose out of the cat flap etc.

7. To View How Long Since the Cat(s) Last Used the Cat Flap

7.1 To view how many hours and minutes since cats 1, 2 or 3 last used the cat flap, press the + button.
7.2 The display will show the symbol for 'CAT 1' and how many hours and minutes ago 'CAT 1' used the flap up to a maximum of 99 hours.
7.3 Press ^+ again for similar information on Cats 2 and 3.
7.4 Press ' + ' a fourth time (or leave for 20 seconds) and the normal display will be resumed.

8. Training Your Cat to Use the Cat Flap or if Your Cat Has Lost its I.D. Disc

It may take a little time for your cat to get used to its new cat flap. To help your cat get used to entering and exiting the flap, the flap can be set to 'TRAINING MODE' by pressing and holding the 'PROGRAM' button and within 3 seconds briefly pressing the '4 WAY' button. After 5 seconds the lock will unlock and the 'PROGRAM' button should then be released. The 'IN & OUT' symbol will remain flashing.

Please be aware that in 'TRAINING MODE' your cat flap will allow access for other animals.

To exit the 'TRAINING MODE', press and hold the 'PROGRAM' button and within 3 seconds briefly press the '4WAY' button. After 5 seconds the flap will re-lock and the 'PROGRAM' button should then be released.

For very hesitant cats, whilst in the TRAINING MODE', the cat flap can be taped or propped open, and food used to encourage the cat to enter and exit the flap.

NOTE: We do NOT recommend that cats, particularly kittens, are left alone to use their cat flap until you are satisfied that they are completely familiar with its operation.

9. Battery Replacement

When the 'BATTERY INDICATOR' comes on, alkaline batteries should be replaced. (See Section 2).

Please note, after fitting new batteries:

'BATTERY INDICATOR' may remain on for up to 15 minutes.
- Flap will remember all I.D. Disc(s) and microchip(s), Lock Settings and Lock Times but 'TIMER' SETTINGS WILL NEED RESETTING. (See section 4.3).

10. Reprogramming a New I.D. Disc or Microchipped Cat

10.1 Press the 'PROGRAM' button on the circuit board (Fig. 4), for 5 seconds, the next unused Cat number will flash and there will be lines moving around the first TWO ZEROS'.
10.2 Press the +1 button to select the appropriate Cat number for a replacement I.D. Disc or select the next available Cat number. (A 'P' next to the Cat number indicates that it has already been programmed, although you may reprogram as follows).
10.3 Place the front of the I.D. Disc in the tunnel opening (Fig. 5) or to program your cat's microchip, encourage your cat to slowly pass through the tunnel by holding the flap open as shown in Fig. 6.
10.4 When programmed, the TWO ZEROS' will disappear and 'Pr' will flash.
10.5 Take the I.D. Disc or your cat well away from the flap and then press the 'SET' button to save the setting.

For additional cats, up to a maximum of 9, repeat steps 10.1 to 10.5.

11. Factory Reset

To reset the cat flap back to the setting when you first bought it, press and hold the 'PROGRAM' button and within 3 seconds press and release the '4 WAY' button, then press and release the 'SET' button. Release the 'PROGRAM' button when all symbols show on LCD. After a period of self checking, the 'IN & OUT' symbol will be all that is visible on the LCD display. This procedure will erase all I.D. Disc(s) / microchip(s) and all other settings. You will then need to re-program the I.D. Disc(s) / microchip(s) (See Section 3).

12. Energy Saving Mode

The flap is supplied with energy saving mode disabled as this makes it easy for your cat to get used to its new flap. In this mode the flap has the quickest possible response time to the cat's microchip.

Once the cat has become accustomed to using the cat flap it is recommended that energy saving mode is enabled. This gives the longest battery life and better security against entrance by raccoons and persistent neighbourhood cats.

You can switch the flap to energy saving mode ('Eon') as follows:

12.1 Press and hold 'PROGRAM' button and within 3 seconds briefly press the 'SET' button. When the display shows 'EOFF' or 'Eon' release the 'PROGRAM' button.
12.2 You may toggle between 'EOFF' and 'Eon' by pressing the '4 WAY' button. Press 'SET' to save the setting.

13. Troubleshooting

13.1 Cat will not use the flap

It may take time for timid cats to learn how to use the cat flap - even if they have used another cat flap before.
- First try using 'TRAINING MODE' (See Section 8).
- Check the energy saving mode is disabled so your cat will find it easier to use the flap (See Section 12).

13.2 Flap does not open in response to programmed I.D. Disc or microchip

• Check '4 WAY' lock is programmed to permit access in the chosen direction.
• Ensure a timed lock is not activated, (evident by flashing '4 WAY' lock setting). If required, cancel the timed lock, (See Sections 4.3.12 to 4.3.14).
• Product Ref. 305 only: If display shows 'IND' check that the cat seeking access is allowed access in the direction being sought by pressing the '4 WAY' button for 1 second and release repeatedly. If necessary, reprogram the cats individual access option. (See Section 4.2).
• The energy saving circuitry may have been activated (denoted by 'Eon' on the display). Do not move the flap until 'Eon' disappears.
• Check batteries are correctly orientated (Fig.3) and the low battery symbol (Fig.1) does not show.
• Check the I.D. Disc is correctly fitted to cat's collar (See Section 5.2).
• If possible, try operation with another programmed I.D. Disc / microchip to ascertain if there is a fault with a particular I.D. Disc / microchip.
• Check that the cat flap is mounted at correct height (See Fitting Instructions).
• If all else fails, remove batteries and wait a minimum of 5 minutes. Refit batteries and then perform a 'FACTORY RESET' (See Section 11).

13.3 Flap has not fully closed

This problem may happen very occasionally and will normally self correct within 30 minutes. If problem persists remove batteries for 5 minutes before replacing when correct lock action should be resumed.

13.4 Difficulty in setting required functions/times

• Buttons need to be pressed firmly.
• Remember to press the 'SET' button after making any change to save the setting.

13.5 Display locks up

• Remove batteries for 5 minutes, then replace.
• If the display is still locked perform a 'FACTORY RESET' (See Section 11).

13.6 Flap does not lock

• Check flap not in 'TRAINING MODE' (slowly flashing arrows).
• Wait 30 minutes for self correction.

FCC STATEMENT

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.

1. Changes or modifications not expressly approved by the party responsible

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

D

Inhalt Seite

Oh, I am so happy to see that the new Kalzenklappe are now in their hands. The Kalzenklappe has been given to me by the Gesellschaft für die Gewöhnung des Konzerns, which is a company of the German Association for the Study of Technology (GAS). The GAS has been established in Germany since 1960 and has been active in research on the application of information technology (IT) in the fields of IT, business management, and information technology.

1.1 Place exterior frame in desired position on door. We recommend the bottom of the aperture is approximately 150mm (6") above ground level. (Fig. 1a/b). If you must fit higher consider providing a step to help your cat enter.
1.2 Draw around the aperture (Fig. 1a), then using an electric jigsaw cut 5mm (^3 / 6^ ) outside of the line. (Fig. 2a).

Installation in metal doors: Draw around the OUTSIDE of the frame. (Fig. 1b). Using an electric jigsaw cut 12mm([1]2) INSIDE the line (Fig. 2b) and go to instruction 1.6.

Be careful to cut hole square to the door, particularly with thicker doors. Ensure interior frame is free fitting in hole.

1.3 Determine thickness of door panel, (t). (Fig. 3).

1.4 Holding the interior frame and the exterior frame in position, mark the 2 screw holes. (Fig. 4).

1.5 Remove the frames and drill screw clearance holes in panel to 6mm ( 14 ) diameter.

1.6 Position interior frame on inside of door and screw exterior frame to it by using appropriate screws for panel thickness, (t), as shown in Fig. 6. If necessary, cut supplied screws to length. Finally fit two screw caps.

1.7 For metal panels:

Product Ref. 305, 355, 356 - remove batteries for a minimum of 2 minutes after installation. This will enable the cat flap to retune itself to its new location for maximum performance.

Product Ref. 306 - remove battery cover and push electrical connector (E) on to pins as shown in Fig. 5.

2. Glass Panels 0-50mm (0-2") Thick

2.1 We recommend that you ask a glazier to cut a hole of 232mm ( 9^1/3 ) diameter in the position required and then install the cat flap as detailed below.

Alternatively, you may prefer to replace the glass panel with a clear plastic panel and install as instructions 1.1 to 1.6.

Note: It is not possible to cut a hole in double glazed or toughened glass. You will need a new panel with the hole already cut from your glazier.

2.2 Determine thickness of door panel, (t). (Fig. 3).
2.3 The black foam seal is not suitable for fitting to glass and should be removed. If desired, the exterior frame may be sealed to the glass panel using silicone sealant.
2.4 Position interior frame on inside of door, screw exterior frame to it by using appropriate screws for panel thickness, (t), as shown in Fig. 6. If necessary, cut supplied screws to length. Finally fit two screw caps.

3. Wall Fitting

If you are installing your cat flap in a wall, you will need to purchase Elite wall liners. You will need 1 wall liner for every 50mm (2^ ) of wall thickness over 50mm (2^ ) for Product Ref. 305, 306, 307 or 100mm (4^ ) for Product Ref. 355, 356 cat flaps.

3.1 Create a rectangular hole in your wall 205mm (8") high by 180mm (7") wide.
3.2 Remove interior frame battery cover by pushing up as shown, (Fig. 7). Product Ref. 307 only: Remove the 4-way knob as shown in Fig. 12 using a thin screwdriver to lever off cover (A) as shown.
3.3 Remove interior frame cover by unscrewing 2 screws in rear of interior frame (Fig. 8). (Note: these screws may be discarded as it will be impossible to refit them). Next remove the 2 screws under the battery cover and remove the interior frame by pivoting down (Fig. 9).
3.4 Carefully remove 2 screw clips with pliers. (Fig. 10).
3.5 Fit interior frame assembled with requisite number of wall liners to interior wall securing in position with 2 suitable screws as shown in Fig. 11. (Note: you will need to fit a washer (not supplied) under the head of the screws). If required, the wall liners may be glued in place, although a firm push fit will usually suffice.
3.6 Refit interior frame cover with 2 screws under battery cover, taking great care not to trap electrical wires. (Product Ref. 307 only: Refit the 4-way knob using a hand screwdriver.) Replace the battery cover.
3.7 Fit exterior frame using 2 off 25mm (1") screws supplied and finally, fit 2 screw caps.

D

WICHTIG:

Pet Mate Ltd. guarantees your product for a period of 3 years from the date of purchase, subject to the registration of your purchase details on our website www.pet-mate.com within 14 days of purchase. (If you do not have access to a computer, please send details of your purchase with copy of receipt along with your name and address.) In the event of a fault developing contact Pet Mate customer services for a returns authorisation number. The guarantee is limited to any defect arising due to faulty materials or manufacture. Any defective item will be repaired or replaced free of charge at the manufacturer's discretion, provided that the defect has not been caused by neglect, misuse or normal wear and tear. Your statutory rights are not affected.

D GARANTIE