Puma Fit - Wristwatch

Fit - Wristwatch Puma - Free user manual and instructions

Find the device manual for free Fit Puma in PDF.

📄 47 pages English EN Download 💬 AI Question 11 questions ⚙️ Specs
Notice Puma Fit - page 3
Pick your language and provide your email: we'll send you a specifically translated version.
Product Type Sports Watch
Brand Puma
Model Fit
Power CR2016 Battery
Modes 5 modes: Time, Chrono, Data, Timer, Alarm
Time zones 2 time zones (T1 and T2)
Chronograph Records up to 9 lap times
Timer 3 types: CD-S (stop), CD-U (continuous), CD-R (repeat up to 30 cycles)
Alarm 2 programmable daily alarms
Lighting Backlight via S4 button
Buttons 4 push buttons: S1 (Start/Stop), S2 (Stop/Reset), S3 (Mode), S4 (Setting/Light)
Display Digital display with icons
Maintenance and cleaning Replace the CR2016 battery when the display fades or disappears
Repairability Battery replacement recommended at an authorized service center

Frequently Asked Questions - Fit Puma

How to set the time on the Fit Puma watch?
Make sure you have the desired time zone displayed (T1 or T2). Press and hold S4 until the seconds flash. Use S1 to change the value, S2 to move to the next option. Press S3 or S4 to exit.
How to switch between the two time zones?
In Time mode, press and hold the S2 button until the T2 or T1 icon stops flashing. Release to switch.
How to use the chronograph?
In CHRO mode, press S1 to start. Press S1 again to record a lap/split time. Press S2 to stop, then press S2 again to reset.
How to view lap times after a session?
Switch to Data mode (DATA). Press S1 to scroll through laps. To view split times, press S4 or wait 4 seconds.
What are the available timer types?
Three types: CD-S (countdown then stop), CD-U (countdown then counting up), CD-R (repeat countdown up to 30 cycles).
How to set the timer?
In Timer mode, press S4 until the digit flashes. Use S1 to change, S2 to move to minutes/hours then to timer type. Press S3 or S4 to exit.
How to set an alarm?
In Alarm mode, press S2 to select AL1 or AL2. Press S4 until the hours flash. Use S1 to change, S2 to move to minutes and time zone. Press S1 to enable/disable the alarm and/or chime.
How to change the watch battery?
When the display fades or disappears, replace the battery with a CR2016. We recommend having this done at an authorized service center.
What does the flashing icon on the screen mean?
Icons indicate the status of functions: alarm enabled, chime enabled, time zone displayed (T1 or T2). Refer to the manual for the exact meaning of each icon.
How to reset the chronograph after stopping it?
When the chronograph is stopped, press S2 to reset it. Note: this erases all session data.

User questions about Fit Puma

1 question about this device. Answer the ones you know or ask your own.

Ask a new question about this device

The email remains private: it is only used to notify you if someone responds to your question.

How to set up beeps or alerts on my Puma Fit watch?
Frequently Asked Questions - 12/06/2026
Response Notice-Facile

The Puma Fit watch offers two programmable daily alarms with configurable chime.

Setting up an alarm with beep:

  • Access the Alarm mode and press S2 to choose between AL1 or AL2
  • Press S4 until the hours start flashing
  • Use S1 to adjust the values (hours and minutes)
  • Press S2 to move to the next settings

Activating the chime (beep):

Once the alarm is set, you can enable or disable the chime by pressing the S1 button. The activated alarm icon will appear on the screen to confirm your setting.

Note: The Fit watch does not have a continuous hourly beep function (every hour). It only offers the 2 programmable daily alarms with chime. If you are looking for an alert every hour, check the timer settings or a third-party app if your watch supports custom notifications.

Respond (be the first)

Download the instructions for your Wristwatch in PDF format for free! Find your manual Fit - Puma and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Fit by Puma.

USER MANUAL Fit Puma

natural_image White Puma logo on red background, no text or symbols present

P.4 ENGLISH
P.12 ČESKY
P.20 HUNGARIAN
P.28 DEUTSCH
P.36 ESPAÑOL
P.44 PORTUGUÊS
P.52 ITALIANO
P.60 FRANÇAIS
P.68 DUTCH
P.76 中文
P.84 日本語

FASS200-250 SS12

APU00586

11/11-HW-20K

ENGLISH

This watch is a dual time sports watch with a unique count down timer. This watch also allows you to view your individual lap times for the duration of your exercise.

Push button Location:
S4 WE25 10:28 38 S1 S3 S2

S1 - Start/ Split/ Set

S2 - Stop/ View/ +

S3 - Mode

S4 - Light

ICON

Puma Fit - ICON - 1

Alarm is on

Puma Fit - ICON - 2

Chime is on

Puma Fit - ICON - 3

Time 1 is displayed

Puma Fit - ICON - 4

Time 2 is displayed

Changing modes

The watch has 5 modes. You can change modes by pressing S3.

Puma Fit - Changing modes - 1

flowchart
graph TD
    A["TIME"] --> B["CHro"]
    B --> C["DATA"]
    C --> D["AL"]
    D --> E["Tm r"]
    E --> A

TIME Mode

The watch has a dual time feature, to view time 2 just press S2 and to switch from time 1 to time 2 or vice versa press and hold S2 until T2 or T1 icon stops blinking.

WE25 10:28 38 Release S2 #TU24 1:28 38 Hold S2 #TU24 1:28 38

From TIME mode you can directly go to TIMER mode by pressing S1.

WE25" 10:28 38 → Tmr

Setting the Time

Time 1 and Time 2 can only be set separately, to set time 1 make sure that the watch is currently displaying time 1. Then press and hold S4 until you see the seconds digit blinking.

WE25" 10:28 38 Hold S4 WE25" 10:28 38

Press S1 to change the current value of the blinking digit.

WE25" 10:28 38 S1 WE25" 11:28

Press S2 to move on to the next option and press S3 or S4 to exit time settings.

Second Hour Minute Weekday 12/24H Date Month Year

To set Time 2 just follow the same steps in setting Time 1 but this time make sure Time 2 is displayed on the watch.

CHRONO Mode

The Chrono mode for this watch can take up to 9 laps. The time for each lap can be viewed in DATA mode.

Press S1 to start the Chrono timer.

"5T P 00'00 00 Sstart "Run 00'09 98

Press S1 again to take a lap or split time.

"Run 00'09 98" ⇒ "'LAP1' 00'09 98" ⇒ "'SPL1' 00'09 98" ⇒ "'Run' 00'17 98" 4 Sec Or Press S4 4 Sec Or Press S4

Press S2 to stop the Chrono timer. Press S2 again while Chrono timer isn't running to reset the timer.

Please take note, once timer has been reset all data for that run can no longer be viewed in DATA mode.

Run 00'17 98 ST P 00'17 98 ST P 00'00 00

DATA Mode

In this mode you can view the individual lap/ split time for you exercise as long as chrono timer has not been reset to zero.

To view the different laps, press S1.

4.4 LAP1 00'09 98 S1 4.4 LAP2 00'06 00

To view the split time of the different laps, press S4 or wait for 4 seconds.

LAP Spilt ** LAP I 00'09 98 4 Sec Or Press S4 ↔ 4 Sec Or Press S4 ** SPL I 00'09 98

TIMER Mode

The watch has 3 types of timers in this mode CD-S (Count Down Stop), CD-U (Count Down Up) and CD-R (Count Down Repeat).

The watch has 3 types of timers in this mode CD-S (Count Down Stop), CD-U (Count Down Up) and CD-R (Count Down Repeat).

Cd 5 1:00 00 S4 Cd 5 1:00

Press S1 to change the value of the blinking digit.

d-4 Cd-5 1:00 S1 d-4 Cd-5 2:00

Press S2 to go to the next option.

Hour Minute **Cd*5 1:00 → **Cd*5 1:00 → **Cd*5 1:00 CD-S/CD-U/CD-R

Press S3 or S4 to exit timer settings.

The CD-S timer or count down stop timer function just like a regular count down timer, once it reaches zero, it stops. While the CD-U or count down up timer, counts down using the set count down time and then when it reaches zero will start to count up until timer is stopped or reaches 99:59'59. The CD-R or count down repeat will continually repeat the set count down time for 30 cycles or until timer is stopped.

All the 3 timers count down timers will start giving out a 5 beep alert sound at 5 minutes, 2 beeps at 2 minutes, 1 beep at 1 minute and a 10 seconds beep just before reaching zero.

Press S1 to start the timer.

44 Cd 5 1:00 00 S1 44 1:00 0:59 59

Press S4 to view the type of timer selected.

X 1:00 0:59 S1 X Cd 5 0:59 S9

Press S2 to stop the timer.

d-4 100 0:59 S9 S2 d-4 100 0:59 S9

Press S4 to reset timer to set value while timer is not running.

X 1:00 0:59 59 S4 X Cd 5 1:00 00

ALARM Mode

This watch has 2 daily alarms, which can be set for T1 or T2.

Press S2 to select Alarm 1 or 2.

44 AL - 1" 12:00 ON S2 44 AL - 2" 12:00 ON

Press S1 to turn on or off the selected alarm or chime.

Alarm ON & Chime ON 12:00 AL - 1 12:00 Alarm OFF & Chime OFF AL - 1 12:00 AL - 1 12:00 Alarm ON Chime ON AL - 1 12:00

Press and hold S4 until the hour digits start to blink, to set the selected alarm.

AL - 17 12:00 ON 3 /4 $4 AL - 17 12:00 ON

Press S1 to change the value of the blinking digit.

AL - i71 12:00 S1 AL - i71 1:00

Press S2 to go to the next option.

Hour ** AL - 1 12:00 on Minute ** AL - 1 12:00 on T1/T2 ** AL - 1 12:00 on

Press S3 or S4 to exit alarm settings.

Battery Replacement:

If the display goes dim or goes totally blank, it is time to replace the battery. The user is recommended to go to authorized service center for correct battery replacement (CR2016).

Česky

chemical Chemical reaction diagram showing conversion of Cd²S to Cd²S and then to Cd²S with 1:00 ratio

Modo de ALARME

flowchart
graph TD
    A["设置调铃"] --> B["S2 S2 S3"]
    B --> C["S3/ S4"]
    C --> D["12:00"]
    D --> E["S3/ S4"]
    E --> F["12:00"]
    F --> G["S3/ S4"]
    G --> H["12:00"]
    H --> I["12:00"]
    I --> J["12:00"]
    J --> K["12:00"]
    K --> L["12:00"]
    L --> M["12:00"]
    M --> N["12:00"]
    N --> O["12:00"]
    O --> P["12:00"]
    P --> Q["12:00"]
    Q --> R["12:00"]
    R --> S["12:00"]
    S --> T["12:00"]
    T --> U["12:00"]
    U --> V["12:00"]
    V --> W["12:00"]
    W --> X["12:00"]
    X --> Y["12:00"]
    Y --> Z["12:00"]
    Z --> AA["12:00"]
    AA --> AB["12:00"]
    AB --> AC["12:00"]
    AC --> AD["12:00"]
    AD --> AE["12:00"]
    AE --> AF["12:00"]
    AF --> AG["12:00"]
    AG --> AH["12:00"]
    AH --> AI["12:00"]
    AI --> AJ["12:00"]
    AJ --> AK["12:00"]
    AK --> AL["12:00"]
    AL --> AM["12:00"]
    AM --> AN["12:00"]
    AN --> AO["12:00"]
    AO --> AP["12:00"]
    AP --> AQ["12:00"]
    AQ --> AR["12:00"]
    AR --> AS["12:00"]
    AS --> AT["12:00"]
    AT --> AU["12:00"]
    AU --> AV["12:00"]
    AV --> AW["12:00"]
    AW --> AX["12:00"]
    AX --> AY["12:00"]

Figure 12

注:

Manual assistant
Powered by Anthropic
Waiting for your message
Product information

Brand : Puma

Model : Fit

Category : Wristwatch