Silence Force Extreme MultiCyclonic - Vacuum Cleaner ROWENTA - Free user manual and instructions

Product type	Cyclone bagless vacuum cleaner
Brand	Rowenta
Model	Silence Force Extreme MultiCyclonic
Filtration system	Multi-cyclonic + HEPA filter (ref. ZR9015 01) + black foam filter + microfilter
Power supply	Mains, electric cord
Weight	Approximately 5.5 kg
Dust container capacity	Main container + fine dust container, do not exceed max level
Main filter	HEPA filter (ref. ZR9015 01) to be replaced every 12 months
Black foam filter	Washable (every 6 months or if suction is insufficient)
Microfilter	Washable (every 6 months)
Power control	Yes, on the handle (POWER CONTROL): 3 positions (min, medium, max)
Tube	Metal telescopic with locking system (LOCK SYSTEM)
Included accessories	Hose with ERGO COMFORT SILENCE handle, all-floor nozzle, telescopic crevice tool, upholstery nozzle, Delta parquet nozzle, rectangular parquet nozzle, turbo brush, mini turbo brush (depending on model)
Main functions	Vacuuming hard floors, carpets, rugs, furniture, corners
Storage and transport	Carrying handle, parking position, accessory holder
Safety	Motor overheating protection, filter cassette presence safety system
Maintenance and cleaning	Empty container after each use, wash foam and microfilters every 6 months, clean air/dust separation system
Spare parts and repairability	Filters and accessories available from retailer or Rowenta Authorized Service Center. Repairs by specialists using original parts.
Warranty	International warranty (conditions in manual)

Frequently Asked Questions - Silence Force Extreme MultiCyclonic ROWENTA

How to empty the dust container?

Take the dust container by the handle and pull it (fig.15). Unlock the fine dust container (5b) from the main container (5a) (fig.16). Empty the main container over a trash can (fig.17) then the fine dust container (fig.18). Clean the seals with a cloth, then reassemble and replace the container (fig.19-20). Never exceed the max level.

How often should the black foam filter be washed?

Every 6 months or when suction is no longer satisfactory. Open the cover, remove the filter, wash it with clean water, wring it out and let it dry for at least 12 hours before replacing. Never put it back damp.

How to clean the HEPA filter?

Open the HEPA filter access hatch (fig.28), remove it and tap it gently over a trash can (fig.30). Do not wash it. Replace it and close the hatch until it clicks. Replace it every 12 months (ref. ZR9015 01).

The vacuum cleaner is not suctioning, what to do?

Check that no accessory, tube or hose is blocked. Clean the black foam filter, microfilter and HEPA filter. Empty and wash the dust container. Make sure the cover is properly closed and the container is correctly positioned. If the problem persists, contact a Rowenta Authorized Service Center.

How to assemble the tube and accessories?

Insert the hose into the suction inlet (fig.1). Attach the metal telescopic tube to the handle until it clicks (fig.3). Attach the all-floor nozzle to the tube (fig.4). Adjust the tube length with the telescopic button (fig.5). To change accessories, always stop and unplug the vacuum cleaner.

What to do if the separator fills with dust?

Check that nothing is blocking the duct between the separation compartment (4c) and the dust container. Clean the container seals. Open the cover, press the separator ejection button (fig.33), remove and wash the parts (4a+b and 4c) with clean water, let dry for 6 hours, then reassemble respecting the closing direction until it clicks.

How to adjust the suction power?

Use the mechanical power control (POWER CONTROL) located on the handle (fig.9). MIN position for delicate fabrics, MEDIUM for daily vacuuming, MAX for hard floors and heavily soiled carpets.

How to store the vacuum cleaner after use?

Press the stop pedal and unplug. Store the cord by pressing the cord rewind pedal (fig.11). Place the tube in the storage at the back of the appliance (fig.13). Use the carrying handle to move the vacuum. Never carry by the container handle.

Where to buy replacement filters?

Filters and accessories are available from your retailer, at Rowenta Authorized Service Centers or by contacting consumer service. The HEPA filter has reference ZR9015 01, the filter cassette (foam + microfilter) reference RS-RT3587.

How to clean the air/dust separation system?

Remove the hose, open the cover, press the separator ejection button (fig.33), then remove the separation system (fig.34). Separate the separation compartment (4c) by turning slightly (fig.35-36). Wash the parts with clean water (fig.37) and let dry for 6 hours. Reassemble by clicking into place (fig.38-40) and close the cover.

USER MANUAL Silence Force Extreme MultiCyclonic ROWENTA

1. Terms and conditions for use 8
2. Power supply 8
3. Repairs 8

DESCRIPTION 8

BEFORE FIRST USE 9

1.Unpacking 9
2. Recommendations and precautions 9

USE 9

1. Fitting the elements onto the appliance 10
2. Plugging in the power cord and switching on the appliance 10
3. Storing and transporting the appliance 10

CLEANING AND MAINTENANCE 10

1. Emptying the dust compartment 10
2. Cleaning the black foam filter 10
3. Cleaning the microfilter 10
4. Cleaning the HEPA filter 11
5. Cleaning the air/dust separator system 11
6. Cleaning your vacuum cleaner 11

TROUBLESHOOTING 11

WHERE TO BUY ACCESSORIES 12

DISPOSAL/ENVIRONMENT 12

WARRANTY

• This appliance is for domestic use only; any misuse or use - Read the instructions for use carefully before using your that does not conform to the instructions will release the appliance for the first time: use that does not conform to the brand from all liability and the warranty will be cancelled. instructions will release Rowenta from all liability.

SAFETY INSTRUCTIONS

For your safety, this appliance complies with all applicable and store the appliance out of the reach of children.

standards and regulations (Low Voltage 2006/95/EC, Electromagnetic Compatibility 2005/108/EC, Environm directives, etc.).

Never leave the vacuum on unsupervised.

This appliance should not be used by persons (including children) with reduced physical, sensory or mental abilities, or by persons lacking experience or knowledge, unless they are not watched over or trained on how to use the appliance.

Do not place the nozzle or the end of the tube near the eyes or ears.

Do not vacuum wet surfaces, any type of liquids, hot substances, supersmooth substances (platinum, cement, ash, etc.), large sharp waste (glass), harmful products (solvents, abrasives, etc.), aggressive products (acids, cleaning products, etc.), inflammable and explosive products (oil or alcohol based).

Never immerse the appliance in water; do not spill water on the appliance and do not store it outside.

Do not use the appliance if: it has been dropped and there is visible damage or it fails to function correctly.

In this case, do not open the appliance but send it to the nearest Approved Service Centre or contact Rowenta Customer Services.

Children should be supervised to ensure they not play with the appliance.

This device can be used by children over 8 years old and by persons with reduced physical, sensory or mental capacities, and by persons lacking experience or knowledge, if they are correctly watched over, or if they have received proper instructions relative to the safe use of the appliance and if they have fully understood the risks implied.

Children must not play with the appliance. Cleaning and maintenance of this appliance m not be carried out by children unless they are least 8 years old and supervised by a respons' person. Keep the device and its cord away fro children under 8 years old.

2. Power supply

Check that your vacuum cleaner voltage corresponds to that of your domestic power supply. Switch off and disconnect the appliance by unplugging without pulling the cord: immediately after use, before changing accessories, before cleaning, maintenance or changing the filter. Do not use the appliance if the power cord is damaged. The cord under and cord for your vacuum cleaner must be replaced by Approved Service Centre as special tools are required for repair to avoid any risks.

Important: the mains plug should be protected with a 16 A fuse at least. If the circuit breaker is triggered while the appliance is in operation, this may be due to the fact that other appliances with high connected power are connected at the same time to the same electrical circuit. This can be avoided by setting the appliance to a low power before turning on and then adjusting to a higher power.

1·Terms and conditions for use

Your vacuum cleaner is an electrical appliance: is should be under normal conditions for use.

3·Repairs

Repairs should only be performed by specialists using original spare parts.

Repairs carried out by the user can pose a risk and cancel the warranty.

DESCRIPTION

1 Cover
2 Cover release button
3 Front cover
4 Air/dust separation system a - Cone separator
b - Air/dust separation grille
c - Separation compartment
5 Dust compartment
a - Main compartment
b - Fine dust compartment
c - Dust compartment seals
6 Maximum fill level for dust compartment
7 Dust compartment housing
8 Carrying handle

9 Suction inlet
10 Air outlet grille
11 ON/OFF button
12 Power cord wind button
13 Parking positions
14 Wheels
15 Multi-direction wheel
16 HEPA filter housing
17 HEPA filter (ref. ZR9015.01)
18 Filtration cassette (ref. RS-RT3587)
a - Black foam filter
b - Microfilter
19 Filtration cassette detection system (18)

DESCRIPTION

Accessories

20 Flexible hose with power nozzle ERGO COMFORT SILENCE (21)

21 a - ERGO COMFORT SILENCE ergonomic nozzle b - Integrated brush (EASY BRUSH) c - Manual power switch (POWER CONTROL)

22 ERGO COMFORT SILENCE metal telescopic tube a - Nozzle/tube locking system (LOCK SYSTEM) b - Tube adjustment button (TELESCOPIC SYSTEM)

23 ERGO COMFORT SILENCE multi-surface nozzle

a - Nozzle/tube locking system (LOCK SYSTEM)

b - 2-position button: brush retracted for rugs and carpets/brush released for parquet and smooth floors

24 Telescopic crevice nozzle*

25 Upholstery nozzle*

26 Delta parquet nozzle*

27 Rectangular parquet nozzle*

28 Turbo-brush*

29 Mini turbo-brush*

30 Accessory support*

BEFORE FIRST USE

1·Unpacking

Unpack your appliance and remove any labels, keep your warranty form and read the instructions carefully before using your appliance for the first time.

2. Recommendations and precautions

Unwind the power cord completely before each use. Do not jam it and do not allow it to rub against sharp edges.

If you are using an electrical extension, check that it is in perfect condition and that it is suited to the power of your vacuum cleaner. Do not unplug the appliance by pulling on the power cord.

Do not move the vacuum cleaner by pulling on the power cord, the appliance must be moved using its carrying handle.

USE

1 · Fitting the elements onto the appliance

Clip the end of the hose to the suction inlet located at the front of the appliance (fig.1)To remove, unclip the end using the clip and remove.

Fix the accessory support to the notch in the parking position located at the back of the vaccuum cleaner (fig.2) and store the accessories on top.

Note: The accessory support does not need to be removed to open the vacuum cleaner lid.

• Fit the metal telescopic tube to the end of the nozzle until you hear a click indicating that it is locked (fig.3b remove, press the tube lock button and remove.

• Fit the multi-surface nozzle (23) to the end of the metal telescopic tube until you hear a click indicating that it is locked (fig.4). To remove, press the nozzle lock button and remove.

• Adjust the metal telescopic tube to the desired length using the telescopic system (TELESCOPIC SYSTEM) (fig.5).

Fit the corresponding accessory to the end of the metal telescopic tube or the nozzle:

• For rugs and carpets: use the multi-surface nozzle in the retracted brush nozzle position or the Turbo-brush* (fibres and animal hairs).

Do not use the power cord or the hose to lift the appliance. Switch off and unplug your vacuum cleaner after each use. Always switch off and unplug your vacuum cleaner before maintenance or cleaning.

Your vacuum cleaner is fitted with a safety device which prevents the motor from overheating. In certain cases (when used on chairs, sofas, etc.) the safety device may be tripped and the appliance may make an unusual noise that is not serious.

Only use original Rowenta accessories and filters.

Check that all the filters are in place.

Do not operate your vacuum cleaner without the filtration system fitted (foam, microfilter and filter).

Never place the foam and microfilter in the appliance unless they are completely dry.

If you have any difficulties in finding accessories or filters for this vacuum cleaner, contact the Rowenta Customer Service.

• For parquet and smooth floors: use the multi-surface nozzle in the brush release position or for best results use the parquet nozzle*.
• For corners and hard to reach spots: use the telescopic crevice nozzle*.
• For upholstery and delicate surfaces: use the brush with the nozzle (EASY BRUSH) or the upholstery nozzle*.

IMPORTANT: always switch off and disconnect your vacuum cleaner before changing the accessories.

ERGONOMIC RECOMMENDATIONS ERGO COMFORT SILENCE range

Ergonomic, the ERGO COMFORT SILENCE range has been designed to facilitate and improve user comfort when vacuuming.

To prevent bending over and to ensure upright posture, make sure to:

1. Adjust the length of the ERGO COMFORT
   SILENCE metal telescopic tube to your body (fig.6).
2. Place your second hand on the front of the ERGO COMFORT SILENCE nozzle handle (fig.7).

USE

2 · Plugging in the power cord and switching on the appliance

Unwind the power cord completely, plug in your vacuum cleaner and press the ON/OFF button (fig. 8).

ATTENTION: do not operate your vacuum cleaner without the filtration system fitted (foam, microfilter filter).

Set the suction power using the manual power switch* on the power nozzle (fig.9):

• Position (MIN) for vacuuming delicate fabrics (curtains, textiles).
• Position (Medium) for daily vacuuming of all types of surfaces with low levels of soiling.
• Position (MAX) for vacuuming hard floors (tiled floors, parquet, etc.) and rugs and carpets in the case of high levels of soiling.

3 • Storing and transporting the appliance

After use, switch off your vacuum cleaner by pressing the ON/OFF button and unplug it (fig. 10). Wind the power cord by pressing the power cord wind button (fig. 11). It is easy to carry your vacuum cleaner using the handle (8). Do not carry your appliance using the dust compartment handle (fig.12).

When storing your vacuum cleaner, place the tube in its storage compartment at the back of the appliance (fig.13).

You do not need to remove the accessory support (30) to store the accessory range (Fig.14).

CLEANING AND MAINTENANCE

The air we breathe contains particles that can be allergenic: larva and dust mite faeces, mould, pollen, smoke and animal waste (hair, skin, saliva, urine), etc.

The finest particles can penetrate deep inside the respiratory system or can cause inflammation and affect the entire respiratory system.

(H)EPA ([High] Efficiency Particulate Air Filter) filters retain the finest particles.

Thanks to the (H)EPA filter, the air released into the room cleaner than the air suctioned.

IMPORTANT: always switch off and unplug your vacuum cleaner before cleaning or servicing. Check and clean your vacuum cleaner and the different filters regularly.

IMPORTANT: do not operate your vacuum cleaner without the filtration system fitted (foam, microfilter and filter).

1. Emptying the dust compartment (5) After each use, empty the dust compartment as follows:

Take the dust compartment by the handle and remove it (fig. Separate the fine dust compartment (5b) from the main compartment (5a) (Fig.16).

Empty the main compartment over a dustbin (Fig.17) then empty the fine dust compartment (5b) (Fig.18).

Clean the compartment seals using a cloth.

Reposition the fine dust compartment on the main compartment (Fig.19) then put the dust compartment back into place (fig.20).

IMPORTANT: do not use the vacuum cleaner once the maximum level (6) is reached on the dust compartment

2 Cleaning the black foam filter (18a)

IMPORTANT: clean the black foam filter every 6 months or when the suction is no longer satisfactory.

Press the cover release button (fig.21). Tip the cover backwards (fig.22).

Remove the black foam filter (fig.23) then wash and squeeze (fig.24). Leave to dry for at least 12 hours before refitting.

ATTENTION: let the black foam filter dry completely and make sure it is completely dry before placing it back in the appliance.

Reposition the black foam filter and close the cover.

3 · Cleaning the microfilter (18b)

IMPORTANT: clean the microfilter every 6 months.

Press the cover release button (fig.21). Tip the cover backwards (fig.22).

Remove the filtration cassette (18) then separate the black foam filter (18a) from the microfilter (18b) (fig.25).

1 Wash the microfilter (fig.26). Leave to dry for at least 12 hours before refitting.

ATTENTION: let the microfilter dry completely and make sure that it is well dry before refitting on the appliance.

Reposition the black foam filter and close the cover.

CLEANING AND MAINTENANCE

ATTENTION: your appliance is equipped with a safety system (19) for detecting the filtration cassette: the cover cannot be closed if the filtration cassette is not fitted (18a + 18b)

IMPORTANT: if the appliance does not perform as norm after cleaning the black foam filter and microfilter on you vacuum cleaner, clean the HEPA filter.

4 · Cleaning the HEPA filter (17)

Remove the accessory support (30) then place the vacuum cleaner in the vertical position (Fig.27).

Open the HEPA filter hatch (Fig.28).

Remove the HEPA filter from its housing (fig.29). Clean the HEPA filter by gently patting it over a dustbin (fig. 30).

Reposition it in its housing (Fig.31).

Reposition the hatch until you hear a click indicating that it is closed (Fig. 32).

IMPORTANT: replace the HEPA filter every 12 months. The HEPA filter (ref ZR9015.01) is available from your dealer or in Approved Service Centres.

5. Cleaning the air/dust separator system (4)

Remove the hose from the vacuum cleaner.

Open the vacuum cleaner cover (fig. 21-22).

Press the separator release button (fig.33) then remove from

the separation system (fig.34).

Remove the separation compartment (4c) by turning slightly to the left (fig.35) then separate the two components (fig.36). Wash the components (4a + b and 4c) in clear water (fig. 37) and leave to dry for 6 hours.

Refit the filter system components (4):

• Reposition the separation compartment (4c) on the separation system (4a + b) (fig. 38) by turning slightly until you hear the click indicating that it is closed (fig. 39).
• Then reposition the entire separation system (4) in the appliance (fig. 40) and close the cover.

6 · Cleaning your vacuum cleaner

Wipe the body of the vacuum cleaner and accessories with a soft damp cloth, then dry with a dry cloth.

Wash the dust compartment (5a+ 5b) under clear or soapy water, then dry with a dry cloth.

IMPORTANT: do not use aggressive or abrasive detergents. The transparency of the dust compartment and/or front cover and/or cover may change over time; this does not affect the appliance performance.

ATTENTION: do not wash the vacuum cleaner cover under clear water. Clean using a soft wet cloth.

TROUBLESHOOTING

IMPORTANT: stop your vacuum cleaner immediately by pressing the Start/Stop button as soon as it stops performing as normal and before performing any checks.

If your vacuum cleaner will not start

• The appliance is not powered. Check that the appliance is plugged in correctly.

If your vacuum cleaner has no suction power
- An accessory, the tube, hose, separator (4a), air/dust separation grille (4b) or the separation compartment (4c) is blocked: unblock them.
- The black foam filter (18a) is saturated: clean it.
- The microfilter (18b) is saturated: clean it.
- The HEPA filter (17) is saturated: clean it by patting it over a dustbin. If the HEPA filter is damaged, change it.

If your vacuum cleaner has less suction power, is noisy or makes a whistling noise

• An accessory, the tube, hose, separator (4a), air/dust separation grille (4b) or the separation compartment (4c) is partially blocked: unblock them.
• The dust compartment is full: empty and wash it.

• The vacuum cleaner cover is not fitted correctly: close properly.

• The dust compartment is not correctly fitted: fit it correctly.

• The nozzle's manual power switch* is open: close it.

If the cone separator (4a) fills up

• Dust accumulates in the separation compartment (4c): Check that the pipe between the separator (4c) and the dust compartment (5) is not blocked. Check that nothing is obstructing the dust compartment inlets.
• The dust compartment inlets are blocked: remove the dust compartment and empty it. Clean the dust compartment seals.

If it is difficult to move the nozzle
- Open the manual power switch* on the nozzle.

If the power cord does not wind completely

• The cord slows down as it winds up: pull the power cord out again and press the power cord wind button.

If a problem persists, take your vacuum cleaner to your local Rowenta Approved Service Centre.

To find a list of Authorised Service Centres, contact Customer Services, the contact details for which you will find on the enclosed international guarantee card.

ACCESSORIES* USE		FITTING THE ACCESSORY	PLACE OF PURCHASE
Upholstery brush For cleaning upholstery. Attach the	upholstery brush to the end of the nozzle.
Upholstery nozzle For cleaning upholstery. Fit the	upholstery nozzle to the end of the nozzle or tube.
Telescopic crevice nozzle For corners and hard to reach spots.	Fit the telescopic crevice nozzle to the end of the nozzle or tube.
Rectangular parquet nozzle For delicate floors. Fit the parquet nozzle to the end of the tube.
DELTA parquet nozzle For delicate floors. Fit the DELTA	parquet nozzle to the end of the tube.
Mini turbo-brush For deep-cleaning upholstery fabrics.	Fit the mini turbo-brush to the end of the tube.
Turbo-brush For removing animal hairs and fibres embedded in rugs and carpets.	Fit the turbo-brush to the end of the tube.

DISPOSAL/ENVIRONMENT

Packaging: the packaging protecting your appliance consists of environment-friendly and recyclable materials. Packaging that is no longer used should be disposed of at special designated collection points.

The used appliance: do not dispose of your appliance with household waste. Your appliance contains numerous valuable or recyclable materials and therefore should be given to a dealer or a recycling centre for disposal.

Think of the environment!

Used filters: as they do not contain forbidden substances in terms of household waste, the used filters can be disposed of with household waste.

INDICE

GARANTÍA 14

LIMPEZA E MANUTENÇA 22

1. Esvazimiento do recipiente para o po 22
2. Lavagem doimento de espuma preto 22
3. Limpeza do microfiltro 22
4. Limpeza do filtro HEPA 23
5. Limpeza do Sistema de separacao de ar/po 23
   6.Limpeza do aspirador 23

BESCHRIJVING VAN HET APPARAAT 32

WAAR KUNT U ACCESSOIRESC KOPEN 36

AFDANKEN/MILIEU 36

GARANTIE

17 HEPA-Filter (Ref. ZR9015.01)

18 Filterkassette (Ref. RS-RT3587)