BW71 - Baby products ALECTO - Free user manual and instructions

Product type	Bottle warmer
Brand	Alecto
Model	BW71
Power supply	220-240 V AC
Power consumption	95 Watts
Heating system	PTC with temperature control
Operating ambient temperature	Between +7°C and +37°C
Use	Heats bottles and baby food jars
Operation	Push button to position "☐" for bottle, "^2" for jar; indicator lights
Safety	Never use without water; do not immerse; dry, horizontal surface
Cleaning and maintenance	Clean with damp cloth; do not use abrasive products
Decalcification	Use white vinegar to remove limescale deposits
Repairability	Do not repair yourself; contact Alecto service at [phone]
Box contents	Bottle warmer, bottle lifter, user manual
Warranty	Consult declaration of conformity on www.alecto.info
Recycling	Do not dispose of with household waste; take to WEEE collection point

Frequently Asked Questions - BW71 ALECTO

How to adjust the milk temperature if it is too high?

If the final temperature is too high, use less water in the bottle warmer. Fill the inside of the warmer with water only up to half the height of the milk in the bottle. You can also remove and shake the bottle during heating to distribute the heat evenly.

How much water should I put in the bottle warmer?

First place the bottle (partially filled) in the appliance, then fill the remaining space with water up to half the height of the bottle's content. For baby food jars, fill to just below the top of the jar.

How to test the temperature of the food before serving?

Test the temperature on the palm of your hand before giving the bottle to your baby. If it is too hot, adjust the amount of water. Always shake the bottle after heating to distribute the heat.

Can I use the bottle warmer without water?

No, never use the appliance without water. Heating requires water to function properly and safely.

How to clean the bottle warmer?

Unplug the appliance and let it cool. Clean the inside and outside with a damp cloth. Never immerse the appliance in water and do not use abrasive or cleaning products.

How to remove limescale from the bottle warmer?

Pour white vinegar into the container up to half height and let it sit until deposits dissolve. Rinse thoroughly and wipe with a damp cloth.

What to do if the appliance does not heat?

First check that the button is on the heating position (☐ for bottle, ^2 for jar). Make sure the appliance is plugged in and the outlet works. If the problem persists, contact Alecto service at [phone].

Can I heat glass baby food jars?

Yes, you can heat jars. Remove the label and lid, place the jar in the container using the bottle lifter, then fill with water to just below the rim of the jar. Use the ^2 setting.

How to know when the milk is at the right temperature?

The 'X' indicator light turns on during heating and turns off when the temperature is reached; then the '√' indicator lights up. After a few minutes, the milk is ready. Always shake the bottle before serving.

Where to find the declaration of conformity of the appliance?

You can download the declaration of conformity on the website www.alecto.info.

USER MANUAL BW71 ALECTO

White baby bottle with blue cap and yellow tip, no visible text or symbols on the bottle itself

Alecto®

BW-71

OVERZICHT APERCU UBERBLICK OVERVIEW

Line drawing of a mechanical component with a central shaft and two vertical supports (no text or symbols)

Line drawing of a mechanical component with a central shaft and two vertical supports (no text or symbols)

DÉCLARATION DE CONFORMITÉ

Line drawing of a mechanical component with a central shaft and two vertical supports (no text or symbols)

The final temperature of the milk is determined by the amount of water in the bottle warmer. If the temperature is too high, it is recommended to use less water in the bottle warmer.

It is recommended to fi ll the interior space with water only after placing the bottle inside. Before the fi rst use, fi ll with water by no more than half the height of the milk within in the bottle, it is also advised to regularly take out the bottle and shake well for an even heating of the content.

Check the temperature of the contents on the back of the hand first before feeding it to the baby, to ensure that the temperature of the bottle contents are safe for your baby. If the temperature is too hot, use less water in the inside of the bottle warmer and vice versa.

Line drawing of a mechanical component with a central shaft and two vertical supports (no text or symbols)

Place the (partly) filled bottle inside of the bottle warmer.

Fill the remaining space within the bottle warmer to half the height of the contents within the bottle with water.

IMPORTANT SAFEGUARDS

Read and save these instructions.

Never use the unit without water in it.

Do not move an appliance containing hot liquids.

- Do not immerse appliance, cord or plugs in water or other liquid.

- Place the Baby Bottle Warmer out of the reach of children and on a dry, non-slip, horizontal surface.

- Close supervision is necessary when the unit is used near children.

- Do not let cord hang over edge of table or counter.

- Do not place on hot surfaces or in a heated oven.

- Only use the Baby Bottle Warmer when the ambient temperature is between +7°C and +37°C.

- Change the water in the bottle warmer often for hygienic reasons.

OPERATION

Warming baby bottles:

1. Slide the control knob into position "0" (off).

2. Place the bottle in the container and fill the space between the bottle and the inner container with water up to half the bottle's content.

3. Plug the Baby Bottle Warmer into the mains socket.

4. Slide the control knob into position "☐". The indicator lamp "X lights to indicate the heating operation.

5. After some minutes the milk will have reached just the right temperature for your baby. The indicator lamp “X” goes out and the indicator lamp “√” lights; the same time you will hear some beeps.

6. Slide the control knob into position "0" (off) and disconnect the Baby Bottle Warmer from the mains socket.

7. Remove the bottle from the container and shake it a little to distribute the heat evenly before you allow your baby to drink.

Warming baby food jars:

1. Slide the control knob into position "0" (off).

2. Remove the label and lid from the jar.

3. Place the jar in the container using the lifter and fill the space between the jar and the inner container with water up to just below the top of the jar.

4. Plug the Baby Bottle Warmer into the mains socket.

5. Slide the control knob into position "The indicator lamp" lights to indicate the heating operation.

6. Use the lifter to stir the contents of the jar frequently for more rapid distribution of heat. After a few minutes the food will have reached just the right temperature for your baby. The indicator lamp “ ” goes out and the indicator lamp √” lights.

7. Slide the control knob into position "0" (off) and disconnect the Baby Bottle Warmer from the mains socket.

8. Remove the jar from the container.

MAINTENANCE INSTRUCTIONS

Cleaning:

Disconnect the Baby Bottle Warmer from the mains socket (or the cigarette lighter socket) and allow it to cool down. Clean the container and the outside of the Baby Bottle Warmer with a damp cloth.

Never immerse the Baby Bottle Warmer in water. Do not use cleaning or scouring agents.

Decalcify:

Hard water deposits must be removed. To do this use white vinegar only. Pour the vinegar into the tank at mid-level, allow to rest until the hard water deposits have been completely eliminated. Rinse well and wipe with a damp cloth.

Warning:

If a fault occurs, consult the Alecto service centre at telephone number [phone]. Under no circumstances should you try to repair the Baby Bottle Warmer yourself; do not dismantle. Servicing should be performed by qualified service personnel only.

TECHNICAL SPECIFICATIONS

Power supply : 220-240V AC

Power consumption : 95 Watts

Operational ambient temperature : between +7°C and +37°C

Heating system: PTC with temperature controlled protection

ENVIRONMENT

At the end of the product lifecycle, you should not throw this product into the normal household garbage but bring the product to a collection point for the recycling of electrical and electronic equipments.

DECLARATION OF CONFORMITY

The declaration of conformity is available on the website WWW.ALECTO.INFO

Service Help

Aziëlaan 12

's-Hertogenbosch

WWW.HESDO-SERVICE.NL

[e-mail]

[phone]

24 maanden garantie

Garantie de 24 mois

24 months guarantee

24 Monate Garantie

CE

v1.0