kMix SJM030 - Kettle KENWOOD - Free user manual and instructions

USER MANUAL kMix SJM030 KENWOOD

Head Office Address:

Kenwood Limited, New Lane, Havant, Hampshire PO9 2NH, UK

www.kenwoodworld.com

Designed and engineered by Kenwood in the UK Made in China

ead these instructions carefully and

retain for future reference.

emove all packaging and any

Always use the filter and never over-

fill - boiling water may splash out.

Avoid contact with steam coming

out of the spout area when pouring

and out of the lid or spout area

will get hot during operation.

Never let the cord hang down where

a child could grab it.

Always unplug your kettle

Never put the kettle, powerbase,

cord or plug in liquid.

Never use a damaged appliance.

Get it checked or repaired: see ‘ser-

vice and customer care’.

Caution: Do not operate the kettle

on an inclined surface.

Only use the powerbase supplied

and keep it clean and dry.

Make sure the lid is secure before

switching the kettle on.

Warning: Do not open the lid while

the water is boiling.

Take care when opening the lid -

droplets of hot water may be eject-

Make sure the kettle is switched off

before lifting or pouring.

Remove the kettle from the base

before filling or pouring.

Never put the kettle near or on

cooker hot plates or gas burners.

This kettle is for boiling water only.

This appliance is not intended for

se by persons (including children)

ith reduced physical, sensory or

mental capabilities, or lack of experi-

nce and knowledge, unless they

ave been given supervision or

instruction concerning use of the

appliance by a person responsible

Children should be supervised to

ensure that they do not play with the

Only use the appliance for its intended

domestic use. Kenwood will not accept

any liability if the appliance is subject to

improper use, or failure to comply with

Make sure your electricity supply is

the same as the one shown on the

underside of your kettle.

This appliance conforms to EC

directive 2004/108/EC on

Electromagnetic Compatibility and

EC regulation no. 1935/2004 of

27/10/2004 on materials intended

for contact with food.

before using for the first time

1 Wrap any excess cord around the

bracket on the underside of the

2 Fill to ‘MAX’, boil, then pour the

water away. Repeat 2 to 3 times.

햷 on/off switch with indicator light

1 Fill the kettle through either the

spout or lid. The water level must be

between ‘MAX’ and 1 cup (200mls).

water than you need.

To improve the quality of your drinks

always use fresh water.

Empty the kettle after each use.

2 Check the lid is closed. Close the lid

by pushing down on the finger pad

3 Plug in and switch on.

4 Your kettle will boil and switch off

automatically. To re-boil, wait a few

seconds - the on/off switch needs

If you experience problems

with your kettle switching on

and off during use or

switching off before boiling,

check that the flat element is

free from scale - see

Your kettle is fitted with a filter to

hold back limescale particles.

If you find drops of water under your

kettle, don’t worry - it is just

If you switch on with too little water,

your kettle will cut out automatically.

Switch off, remove from the

powerbase and let it cool down

before re-filling. When it has cooled

down, the switch will reset itself.

Before cleaning, unplug your kettle

and let it cool down.

the outside and powerbase

Wipe with a damp cloth, then dry.

Do not use abrasives - they will

scratch the metal and plastic

Even though your kettle comes with

filter, you still need to clean the

inside (and the filter) regularly.

2 Slide the filter out .

3 either rinse under the tap or use a

or when descaling your kettle, drop

the filter in too. Rinse thoroughly.

4 Slide the filter back in to refit .

Regular descaling of the flat element

will improve the performance of your

kettle. If the kettle is not descaled

regularly the build up of limescale

may result in the following:

problems may be experienced

with the kettle switching on and

off during use or switching off

the kettle may take longer to boil.

the flat element may be damaged.

Please note: Failure to descale your

kettle may invalidate your guarantee.

When limescale starts to build up on

the heating element, buy a suitable

descaler and descale your kettle.

After descaling, boil with fresh water

several times and discard. Clean any

descaler off the kettle - it can

Some regions of the country have

chalky water. This makes boiled

water look cloudy and leaves a

deposit on the side of the kettle. This

is normal but can be removed with

Alternatively, to reduce limescale

build up, use filtered water to fill your

3service and customer

If the cord is damaged it must, for

afety reasons, be replaced by

K ENWOOD or an authorised

If you need help with:

using your appliance or

servicing or repairs

Contact the shop where you bought

Designed and engineered by

At the end of its working life, the product

must not be disposed of as urban

It must be taken to a special local

authority differentiated waste collection

centre or to a dealer providing this

Disposing of a household appliance

separately avoids possible negative

consequences for the environment and

health deriving from inappropriate

disposal and enables the constituent

materials to be recovered to obtain

significant savings in energy and

resources. As a reminder of the need to

dispose of household appliances

separately, the product is marked with

a crossed-out wheeled dustbin.

4voordat u uw Kenwood-

Børn bør overvåges for at sikre, at

4AQ [UIMAJIWXI FSCLIME W[IXMNA PI:

XK [UCWK XKV WYWNIYCV C

XS WBUFMV C XMV ITMWNIYBV ITMNSMQ]QCWXI PI XS NEXAWXKPE ET_

XS STSDS EGSUAWEXI XK WYWNIYC WEV.

=[IHMAWXKNI NEM EQETX`[LKNI ET_

XKQ Kenwood WXS 5Q]PBQS

7EXEWNIYAWXKNI WXKQ 7DQE.