CT25 - Radio control system Corally - Free user manual and instructions

Product type	Radio control system
Brand	Corally
Model	CT25
Operating frequency	2.4 GHz
Modulation	GFSK
Transmitter channels	2
Receiver channels	3
RF Power	<20 dBm
Sensitivity	1024
Transmitter power supply	4 AA batteries (1.5 V)
Transmitter low voltage warning	<4.5 V
Receiver dimensions	38 x 24 x 14 mm
Receiver weight	6 g
Receiver antenna length	150 mm
Main functions	Dual rate steering, steering trim, steering/throttle reverse, speed limiter 50-100%
Compatible model type	Car / Boat
Binding method	Binding via FN button
LED indicator	Solid = OK, Flashing = low battery
Interference protection	Noise suppression capacitors recommended
Usage conditions	Avoid moisture, vibrations, shocks
Maintenance	Check connectors, isolate from vibrations, protect from water
Safety	Do not cover antenna, respect polarities, do not disassemble
Warranty	24 months (EU), 12 months (non-EU)

Frequently Asked Questions - CT25 Corally

How to bind the transmitter and receiver?

To bind, turn off the radio. Hold down the FN button while turning on the transmitter. The LED flashes. Release FN, then power on the receiver (via the controller). The LED becomes solid: binding is successful.

How to reverse steering or throttle direction?

To reverse steering, set the reverse switch to position 1 and press FN for 5 seconds. To reverse throttle, set the switch to position 2 and press FN for 5 seconds.

How to adjust steering trim?

Use the Steering Trim knob to adjust the direction so that the car drives straight without touching the steering wheel.

How to use Dual Rate (D/R)?

Turn the D/R knob clockwise to increase steering travel, or counterclockwise to decrease it. Adjust according to cornering needs.

How to adjust the speed limiter?

The speed limiter has two positions: 1 = 50% (reduced speed) and 2 = 100% (full speed). Use the corresponding switch.

What does the LED flashing mean?

A flashing LED indicates low transmitter battery voltage (below 4.5 V). Replace the 4 AA batteries. A solid LED indicates normal operation.

How to maintain the receiver?

Check that connectors are firmly inserted. Isolate the receiver from vibrations with double-sided tape or foam. Protect it from water using a plastic bag or a waterproof box.

What precautions should be taken with the antenna?

Do not cover the transmitter antenna with your hand. Do not place conductive material on the antenna. For the receiver, never shorten the antenna and install it as high as possible in a tube.

What to do in case of interference?

If interference occurs, reorient the receiving antenna, move the equipment away from other devices, or consult the dealer. Installing noise suppression capacitors on the motor can help.

What is the product warranty?

The warranty covers material and manufacturing defects: 24 months in the EU, 12 months outside the EU from the date of purchase. To claim warranty, contact Team Corally with proof of purchase.

USER MANUAL CT25 Corally

WARNING and SAFETY PRECAUTION

The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product.

CAUTION: Procedures, which if not be properly followed, is able to create a possibility of physical property damage AND or possibility of injury.

ATTENTION: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Fail to operate the product correctly can result in damage to the product, personal property and cause serious injury.

ATTENTION: This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and requires some basic mechanical ability. Fail to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not attempt to disassemble, use with incompatible components or augment product in any way without the approval of Corally. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

SPECIFICATIONS

• 2CH Transmitter with 3-channel receiver.
• The device has an integrated 2.4GHz antenna.
• Steering DUAL RATE (D/R).
• Steering Trim.
• Steering and throttle Reverse
• 50% of 100% throttle power function

TRANSMITTER

Model Type: .Car/Boat

RF power: <20dBm

Modulation: GFSK

Sensitivity: 1024

Low Voltage Warning: <4,5V

Power: 6 VDC (1.5V AA x4)

Range: >200m

Weight: 250g

Dimensions: 160x150x90mm

Certificate: CE - FCC

RECEIVER

Channels: 3

Model type: car/boat

Frequency band: 2.4 GHz

Modulation: GFSK

Sensitivity y: 1024

RF receiver sensitivity: -100 dbm

Power: 4.5-7.2 vdc

Weight: 7g

ANT length: 106 mm

Dimensions: 38x24x14mm

Certificate: CE - FCC

TRANSMITTER

WARNING : Do not cover/hold the built-in antenna part of the transmitter by your hand during running. Do not put any conductive plate/sticker on the antenna part. Otherwise, the operating range may become shorter.

RECEIVER

Antenna:

Never shorten the antenna.

Install the antenna as far as possible outside the receiver box.

RECEIVER CONNECTION

CONNECTION WITH A CONTROLLER

Install the Receiver in your model using double-sided Velcro. Velcro will hold the receiver in place and protect it from vibrations. Mount the antenna up and away from the vehicle in an antenna tube. The higher up the antenna is, the better signal it will receive.

Install and connect the receiver, servos and other components in accordance with the "Assembly Precautions".

Respect the polarity markings

Remove the cover and insert 4 AA size batteries.

Observe the polarity markings and insert accordingly. Power ON the transmitter and check the Led status.

Battery Voltage LED - SOLID Light = OK

Battery Voltage LED - FLASHING Light = Low Voltage (Replace batteries)

TRANSMITTER FUNCTIONS

ON/OFF SWITCH
Slide RIGHT to turn ON the transmitter

LED Status

SOLID Light = OK
FLASHING Light = Low Voltage (Replace batteries)

SERVO REVERSE

ST.REV (Steering Reverse) :This function reverses the rotation direction of the STEERING servo.

Set the button to position 1 and press the FN button for 5sec to reverse direction.

TH.REV (Throttle Reverse) :This function reverses the rotation direction of the THROTTLE servo.

Set the button to position 2 and press the FN button for 5sec to reverse the GAS.

STEERING TRIM

The steering trim is used to adjust the steering setting so that the car moves in a straight line without using the steering wheel to compensate.

STEERING DUAL RATE (D/R)

Use this function to adjust the steering travel of your model. If the model understeers while cornering, add steering by turning CW of the D/R button. When the model oversteers, take away steering by turning CCW of the D/R button.

OPERATE YOUR MODEL

MOVE YOUR MODEL

MOVE YOUR MODEL

1. Gently pull the trigger to move your model forward.
   The speed is proportional, the more you pull the trigger, the faster the model moves forward.
2. Release the trigger in neutral position to slow down your model.
3. Pull the trigger forward to brake your model.

For reverse, after stopping the model, release the trigger to neutral position then pull the trigger forward again to activate reverse.

BINDING / LINKING THE RECEIVER AND TRANSMITTER

The transmitter and receiver are already paired at the factory and you do not have to do anything. If you wish to connect the receiver with another transmitter or connect a new receiver, or if you have a problem with the link, follow the steps below to re-pair.

Start with the radio in the OFF position

A: Press and hold the FN button.
B: Switch ON the transmitter

The LED flashes
Release the FN button.

Turn ON the controller switch to power the receiver.

The LED is now lit solid.
The binding is complete.

CAUTION

The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer.

PRECAUTIONS

Check the receiver, servos, and battery connectors, to be sure they are firmly connected. If a connector is not fully inserted, vibration may cause the connector to work loose while the model is operating. This will result in loss of control.
Operate each servo horn over its full stroke and check to see that the linkage does not bind or is not too loose. Excessive force applied to the servo horn by binding or poor installation may lead to servo problems and result in loss of control.
Electric Cars and Boats : Isolate the receiver from vibration by attaching to the chassis or mounting plate with thick double sided tape.

Gas Powered Cars and Boats : Isolate the receiver from vibration by wrapping it in foam rubber or similar type cushioning material. Protect the unit from water damage by placing it in a plastic bag or waterproof radio box. The receiver contains precision electronic parts. These parts are vulnerable to vibration and shock. Any contact with moisture (water or condensation) may cause receiver malfunction and loss of control.

Keep all devices that emit high frequency noise, such as motors, batteries, and wiring that handles heavy current loads, at least 1/2 inch away from the receiver and the receiver antenna. High frequency noise will cause a decrease in operating range and could cause loss of control.
Install electronic speed control heat sinks as well as other components that conduct electricity so they can not come in contact with aluminium, carbon fibre or other materials that conduct electricity. If, for example, the speed control came loose while the model was running and touched an aluminium chassis, a short circuit may occur that would cause irreparable damage to the system as well as loss of control.
Noise suppression capacitors should be installed on almost all motors. If the proper capacitors are not installed, high frequency noise will reduce range and cause loss of control along with various other problems.
Inspect all linkage installations and any point where metal could come in contact with other metal parts. Make sure these parts do not touch other metal parts under vibration. Should a linkage or other metal parts come in contact with other metal parts under vibration, the high frequency noise generated by this contact will cause interference and possible loss of control.
Do Not disassemble any part of this system that is not specified in the instruction manual. Corally will not be responsible for any damage due to improper disassembly of any part of the radio control system.

WARRANTY CONDITIONS & LIABILITY DISCLAIMER

If material defects or manufacturing faults should arise in a product distributed or manufactured by Team Corally / JSP Group Intl bvba, and purchased by a consumer, we Team Corally / JSP Group Intl bvba acknowledge the obligation to correct those faults or defects within the limitations described below. This manufacturers warranty is in addition to, and does not affect, the legal or contractual rights of the consumer which arise from the purchase of such products. Team Corally / JSP Group Intl bvba guarantees the consumer that its products are free from material, manufacturing, and construction faults, as determined by the general state of knowledge and technology valid at the time of manufacturing. The fault responsible for causing the damage must be proven to have been present in the product at this time. Claims for compensation arising from consequential damage or product liability will not be considered valid unless they fall under peremptory provisions of the law. If material defects or manufacturing faults should arise in a product distributed or manufactured by Team Corally / JSP Group Intl bvba in the European community (EC) and purchased by a consumer, then Team Corally / JSP Group Intl bvba undertakes to correct those defects within the limitations described below. This manufacturer's declaration does not affect the consumer's legal or contractual rights regarding defects arising from the purchase contract between the consumer and the dealer or reseller. Extend of the Warranty

If a claim is made under warranty, we take at our discretion to repair or replace the defective goods. We will not consider supplementary claims, especially for reimbursement of costs relating to the defect (e.g. installation / removal costs) and compensation for consequent damages unless they are allowed by statute. This does not affect claims on legal regulations, especially according to the product liability law.

Provisions of the Warranty

The purchaser is required to make the warranty claim in writing, and must enclose original proof of purchase (e.g. invoice, receipt, delivery note) and the appropriate warranty card. He must send the defective goods to our local representatives or directly to Team Corally / JSP Group Intl bvba, Geelseweg 80, 2250 Olen, Belgium at his own risk and cost.

The purchaser should state the material defect or manufacturing fault, or symptoms of the fault, as accurate as possible, so that we can check if our warranty obligation is applicable. The goods are transported from the consumer to us, and from us to the consumer, entirely at the risk and cost of the consumer.

Invalidation of the Warranty

The consumer cannot make a claim under warranty when the fault is affecting the use of the product arising from natural wear, competition use, or improper use (including installation) or external forces. The consumer's adherence to the building and operating instructions relevant to the model, including the installation, operation, use of, and maintenance of, model-related components cannot be supervised by Team Corally / JSP Group Intl bvba. Therefore Team Corally / JSP Group Intl bvba is in no way liable for loss, damage, or costs resulting from improper use, or behaviour in any way connected to the above described provisions. Unless otherwise required by law, Team Corally / JSP Group Intl bvba is in no way whatever liable to provide compensation for damages arising from the improper use of the model (including personal injury, death, damage to buildings, loss of turnover, loss of business, or interruption of business, or any other direct, or indirectly caused, consequential damage).

Duration of Validity

The claim period is 24 months from the date of purchase of the product by the consumer from a dealer in the European Community (EC) counted from the date of purchase. The claim period is 12 months from the date of purchase of the product by the consumer from a dealer outside the European Community (EC) counted from the date of purchase. If a defect arises after the end of the claim period, or if evidence or documents required according to this declaration in order to make the claim valid are not presented until after this period, then the consumer forfeits any rights or claims from this declaration. The guarantee period is not prolonged by the granting of any claims within the framework of this warranty, especially in the case of repair or replacement. The guarantee period also does not restart in such cases.

Warranty Expiration

If we do not acknowledge the validity of a claim based on this declaration within the claim period, all claims based on this declaration will expire after six months from the time of registering the claim; however this cannot occur prior to the end of the claim period.

For any support, you can contact us by email at [e-mail]

WEEE: At the end of this device's useful life, please remove all the batteries and dispose of them separately. Take electrical appliances to the local collection points for waste electrical and electronic equipment. Other components can be disposed of in domestic refuse. Thank you for your co-operation!

DECLARATION OF CONFORMITY

EU-Konformitätserklarung · Déclaration de Conformité UE · EU-Verklaring van Overeenstemming

This declaration is issued under the sole responsibility of the manufacturer.

This manual is an edition of Team Corally, Geelseweg 80, B-2250 OLEN (Belgium). This manual is protected by a copyright and nothing from this edition may be reproduced or used without any prior written authorisation. Whilst every effort has been made to ensure the accuracy of the information in this catalogue, errors do creep in and Team Corally can accept no responsibility for failures, wrong specifications, accuracy of colours, losses or damages caused. Team Corally denies any responsibility claims or damages caused by use of our products. Team Corally is not responsible for product changes or availability of our products. The products of dangerous nature included in this manual are submissive to special handling and storage specifications. Please check with your local authorities for existing legislation.

WWW.CORALLY.COM

Team Corally is a registered trademark licensed to JSP Group Int'l BVba • Geelseweg 80 • B-2250 OLEN • Belgium Tel: [phone] • [e-mail]

ADVANCED 2.4GHZ RADIO CONTROL SYSTEM

Alimentation: 6 VDC (1,5V AA x4)

Portee: >200m

Taille: 160 x 150 x 90 mm

Poids: 250g

Certificate: CE0678 - FCC

RéCEPTEUR

Canaux: 3

Alimentation: 4.5-7.2 vdc

Certificate: CE0678 FCC

Dual Rate (D/R) direction

DECLARATION OF CONFORMITY

EU-Konformitätserklarung · Déclaration de Conformité UE · EU-Verklaring van Overeenstemming

This declaration is issued under the sole responsibility of the manufacturer.

Team Corally is a registered trademark licensed to JSP Group Int'l BVba • Geelseweg 80 • B-2250 OLEN • Belgium Tel: [phone] • [e-mail]

ADVANCED 2.4GHZ RADIO CONTROL SYSTEM

DECLARATION OF CONFORMITY

EU-Konformitätserklarung · Déclaration de Conformité UE · EU-Verklaring van Overeenstemming

This declaration is issued under the sole responsibility of the manufacturer.

Team Corally is a registered trademark licensed to JSP Group Int'l BVba • Geelseweg 80 • B-2250 OLEN • Belgium Tel: [phone] • [e-mail]

ADVANCED 2.4GHZ RADIO CONTROL SYSTEM

DECLARATION OF CONFORMITY

EU-Konformitätserklarung · Déclaration de Conformité UE · EU-Verklaring van Overeenstemming

This declaration is issued under the sole responsibility of the manufacturer.

Team Corally is a registered trademark licensed to JSP Group Int'l BVba • Geelseweg 80 • B-2250 OLEN • Belgium Tel: [phone] • [e-mail]

FCC warning statements:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The device has been evaluated to meet general RF exposure requirement.