DU 770 G - Cooking appliance BOMANN - Free user manual and instructions

USER MANUAL DU 770 G BOMANN

Downloaded from www.Manualslib.com manuals search engine ENGLISH

• The appliance is designed exclusively for private Introduction use and for the envisaged purpose. This appli- Thank you for choosing our product. We hope you ance is not fit for commercial use. will enjoy using the appliance.

• The appliance is only to be used as described in the user manual. Do not use the appliance for any Symbols in the these Instructions for Use other purpose. Any other use is not intended and Important information for your safety is specially can result in damages or personal injuries. marked. It is essential to comply with these instruc-

• Operate the appliance only properly installed. tions to avoid accidents and prevent damage.

• Do not use it outdoors. Keep it away from sources WARNING

NING: of heat, direct sunlight and humidity. This warns you of dangers to your health and indi-

• Do not operate the appliance without supervision. cates possible injury risks.

• When not in use, for cleaning, user maintenance works or with disruption, switch off the appliance CAUTION: CAUTION: This refers to possible hazards to the machine or and disconnect the plug (pull the plug itself, not other objects. the lead) or turn off the fuse.
• The appliance and if possible the mains lead have NOTE: NOTE: This highlights tips and information. to be checked regularly for signs of damage. If damage is found the appliance must not be used. General Notes

• For safety reasons, alterations or modifications of the appliance are prohibited. Read the operating instructions carefully before put-

• In order to ensure your children’s safety, please ting the appliance into operation and keep the instructions including the warranty and the receipt. If keep all packaging (plastic bags, boxes, polysty- you give this appliance to other people, please also rene etc.) out of their reach. pass on the operating instructions. WARNING

NING: Do not allow small children to play with the foil. NOTE: NOTE: There is a danger of suffocation! The illustrations in this instruction manual can deviate from the original appliance. Special safety Information for this Unit

• Note to your cooking appliance the manufacturer's instructions whether the operation of a cooker hood is allowed above it and possibly what safety distance must be maintained.

Downloaded from www.Manualslib.com manuals search engine For the extraction mode:

• Provision shall be made for adequate ventilation in the room when the cooker hood is operated simultaneously with appliances that burn gas or other fuels.
• If the cooker hood and other devices which are powered other forms of energy as electricity, served together, the pressure in the room should not exceed 4 Pa (4x10-5 bar).
• The extracted air may not be vented into a flue which is used for the waste gas from appliances which are powered by gas or other fuels.
• When venting the extracted air, comply with the regulations of the relevant local authorities.
• The requirements of the competent local authorities must be observed.

• Observe and follow further installation instructions that we give you in the chapter "Installation".
• ATTENTION: Accessible parts of the appliance may become hot when used with cooking utensils.
• Do not flambé under the cooker hood! You can fry under the hood due to fire hazard only under constant observation.
• Never allow a gas hotplate burning without cookware. Excess heat can damage the cooker hood.
• Overheated fats and oils can ignite easily. Never walk away from fat and oil when heating them.
• Do not check the filter condition while the hood is in operation.
• NEVER use the appliance without fixed aluminum grease filter.
• This appliance can be used by chil children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or

Downloaded from www.Manualslib.com manuals search engine lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

• Children shall not play with the appliance.
• Cleaning and user maintenance shall not be made by children unless they are older 8 years and supervised.
• The appliance must be cleaned regularly. Follow the instructions that we give you in the chapter “Cleaning and Maintenance”. There is a risk of fire if cleaning is not carried out according to these instructions.
• Do not try to repair the appliance on your own. Always contact an authorized technician. To avoid the exposure to danger, always have faulty cable be replaced only by the manufacturer, by our customer service or by qualified person and with a cable of the same type. Unpacking the Appliance Appliance Equipment

• Remove the appliance from its packaging.
• Remove all packaging material, such as foils, filler Appliance overview and cardboard packaging. 1 Telescopic duct, 2-part

• To prevent hazards, check the appliance for any 2 Main body transport damage. 3 Motor unit

• In case of damage, do not put the appliance into 4 Filter operation. Contact your distributor. 5 Glass frame NOTE: NOTE: Production residue or dust may have collected on the appliance. We recommend cleaning the appliance Delivery scope according to chapter “Cleaning and Maintenance”. 1 x outer (lower) duct, 1 x inner (upper) duct (with ventilation slots), 1 x connecting piece with nonreturn valves, incl. Installation material and drilling template

Downloaded from www.Manualslib.com manuals search engine Activated carbon filter are not supplied. You can or- Installation der the carbon filter from your dealer or in our online There must be a safety distance between the hot- accessories shop, www.bomann.de. www.bomann.de To order, use plate of the cooking pot on the hob and the bottom the reference number found under “Technical Data”. part of the cooker hood: The distance must be between 60 – 80 cm. For gas Assembly appliances, the distance must be at least 65 cm. If

• When assembling or inserting the extraction filter a greater distance, this distance must be taken into as well as the carbon filter, the appliance must not consideration. be connected to the mains.
• Failure to use the mounting fixtures may lead to a Selecting the fume outlet risk of electric shock. shock You can operate the cooker hood in two modes: CAUTION: CAUTION: Extraction mode

• Before mounting, check that the wall has sufficient

load capacity to bear the cooker hood.

• The extracted air may not be vented into a flue

• When drilling the holes in the wall always make which is used for the waste gas from appliances sure that no existing electrical cables or other ob- which are powered by gas or other fuels. jects are damaged.

• When venting the extracted air, comply with the

• Make sure that the ventilation slots are clear of regulations of the relevant local authorities. obstacles and are not covered. The hood has an upper air outlet to vent cooking NOTE: NOTE: Recommendations Recommendations for preparation work odours to the outside.

• When installing, ask another person to assist. The extracted air is normally vented verti-

• Wear protective gloves to prevent injuries from cally. The extracted air can vented any sharp edges. through the wall units and the loft floor to

• Determine the position of the cooker hood central- the roof ridge. ly above the hob in conformance with the speci- If there is a conduit under the wall units, fied safety distances. the extraction duct can be routed so that

• Align the drilling template horizontally and mark the extracted air can be vented horizon- the necessary holes for the wall mounting. Check tally through the wall. them with a spirit level.
• Drill mounting holes 4 x Ø8 mm and insert the Recirculation mode dowel pins. If you do not have a direct extraction vent to the outside; the hood can also work in recirculation mode (i.e. without an extraction vent to the outside; the filtered air is released back into the room). In this case, an activated carbon filter as described under “Installing the activated carbon filter for recirculation mode”, must be used.

Downloaded from www.Manualslib.com manuals search engine

• Turn the screws 4 x ST4*35 mm as far as these Installing the activated carbon filter for recirculation recirculation stick out about 10 mm from the wall. mode

• Before suspending the hood, the connecting piece with non-return valves must be installed.

• Open the cover and remove the aluminum grease

• Hang up the hood. Check the secure fitting, the filter. horizontal position and tighten first the upper and

• Place the carbon filter onto the air intake of the then the lower screws through the hood body. extraction duct. Make sure that the mounting pins

• Remove the protective foil from the telescopic on the extraction duct engage the mounting slots duct. of the carbon filter. Turn the filter clockwise until it For the extraction mode: clicks into place.

• Attach a flexible extraction hose (not

• Reinstall the aluminum grease filter and close the supplied) with an inner diameter of cover. Ø150 mm onto the connecting piece. Electrical connection

• Slide the inner (upper) duct along the

slide fixture into the outer (lower)

• The installation to the mains supply must conform duct. Make sure that the inner duct is to the local standards and regulations. aligned with the vents at the top.

• Improper connection may cause to an electric

• Determine the extension length of the duct cover shock! shock by pulling up the inner duct or sliding back into the

• Do not modify the appliance plug. If the plug does outer duct. not fit properly to the outlet, let install a proper outlet by an authorized specialist.
• The accessibility of the power plug must be ensured to disconnect the appliance from the power supply in case of emergency.

• Attach the mounting rail at the upper duct ending. Drill mounting holes 2 x Ø8 mm and insert the

• Ensure that your mains power corresponds with dowel pins. Use the screws 2 x ST4*35 mm to se- the specifications of the appliance. The specifica- cure the rail. tions are printed on the rating label. For the extraction mode:

• Connect the mains cable to a properly installed

• Check the correct position of the flexible extrac- and earthed wall outlet. tion hose and connect it with the extraction outlet

• If the plug after installation is not accessible, a corresponding disconnect device must be availa- to the outside. ble to meet the relevant safety regulations.

• Pull the inner duct upwards and fasten the duct cover laterally to the previously mounted rail using the screws 2 x ST4*10 mm.

Downloaded from www.Manualslib.com manuals search engine Information for disassembly in terms of recycling, Startup / Operation recovery and disposal at the end of the life of the Information to reduce the environmental effect of appliance cooking Check that the unit is disconnected from the power (acc. VO (EU) No. 66/2014 appendix I, No. 2) supply before removing all filter from the hood. Cooker Cooker hood First remove the chimney. The diameter of the pot and pan floors should be When disassembling the hood, be sure that you first according to the size of the cooking zone. loosen the lower and then the upper screws. Use pans and pots with flat floors, uneven floors increase the energy consumption. For the recycling and recovery of resources give the Ensure that there is sufficient supply air for the oper- appliance, the lamps and the various filter to: ation of the cooker hood. - a communal collection point of public waste dispos- Adjust the fan step intensity of the damp evolution of al authorities the cooking process. - a dedicated disposal company, offering a return To product the optimal effect of the cooker hood, system install it according to the installation instructions. - a resident electric trader, who voluntary withdraws Keep the distance between the upper edge of the electrical appliances cooker and the lower edge of the cooker hood. The cooker hood is operated via pushbuttons. Clean the filter regularly. Power level Controll the active carbon filter regularly and renew it as required. 0 off Switch off the cooker hood after use. Lighting If your cooker hood has a switch-off delay, activate medium high on / off this function. Settings Switch off the lighting after the cooking process. We recommend the use of biological cleaners. Power level: level: Suitable for cooking on a low flame and for dishes which produce no or little steam, in Information to professional users for disassembly order to circulate the air around the kitchen. (acc. VO (EU) No. 66/2014 appendix I, No. 2) Power level: level: Suitable for normal cooking. Cooker hood Power level: level: Suitable if large quantities of smoke Information for non-destructive disassembly for and steam need to be extracted or filtered (e.g. when maintenance purposes frying). Please remove the filter and lamps as described in NOTE: NOTE: the manual. With very strong vapor emission, the fan should con- Further steps of disassembly for maintenance are not tinue running after cooking for a few minutes. provided If you would like to exchange defective components, please contact our customer service. Accumulators are not included.

• Alternatively, the grease filter can also be cleaned Cleaning and Maintenance in the dishwasher (up to 60°C). Slight discolora-

• Always turn off the appliance and disconnect from of the grease filter. the power supply before cleaning and user maintenance. Replacing the activated carbon filter

• Allow the appliance cool down sufficiently! The activated carbon filter prevent odors and must

• Do not use steam cleaners for cleaning the appli- depend on the use, but be changed at least every six ance; moisture could enter electrical components. months. Risk of electric shock! Hot steam could damage Order the carbon filter from your dealer or in our the plastic parts. online accessories shop, www.bomann.de. www.bomann.de Use the

• The appliance must be dry before restarting operation. reference number found under “Technical Data”. CAUTION:

• See “Installing the activated carbon filter for recirculation mode”.

• Do not use a wire brush or other sharp, abrasive

• Remove the old carbon filter by turning the filter items. anti-clockwise.

• Do not use any acidic or abrasive cleaners. Replacing the bulb Maintenance of the hood

• To clean the surface of the housing, use a mild Allow the lamps to cool down before replacing the detergent and a soft cloth to prevent scratching. bulbs. Risk of burns! The LED lamp must be re-

• The appliance can be used again after everything placed by a qualified person. has dried properly. NOTE: NOTE:

• If you use your cooker hood in recirculation mode, you must replace the activated carbon filter regu- Oder the lamps from your dealer or in our online larly (see “Replacing the activated carbon filter”). accessories shop www.bomann.de. www.bomann.de Cleaning the aluminum aluminum grease filter WARNUNG: Risk of fire! Grease residue in aluminum grease filter may ignite Lamp specification: LED, 2 x 1.5

at intense heat. Therefore, clean the grease filter

• Remove the aluminum grease filter. regularly!

• Open the black protective housing of the plug-in We recommend cleaning the grease filter monthly: connection with a suitable tool.
• Press out the lamp unit gently from the inside and

• Remove the aluminum grease filter by sliding disconnect it from the connector. back the lock in the handle recess, push the filter

• Connect the new bulb with the connector properly down gently and pull out towards the front. and close the protective housing.

• Rinse the grease filter in a solution of hot water

• Reinsert the lamp unit into the lamp socket until it and neutral detergent. Soak the filter in it. clicks into place.

• Then clean with a soft brush, rinse thoroughly with

• Replace the aluminum grease filter. hot water and allow drying.

Downloaded from www.Manualslib.com manuals search engine Product data sheet for household cooker hoods acac- Troubleshooting cording to regulation (EU) No. 65/2014 Before you contact an authorized specialist Problem Possible Cause / Solution Appliance is not - Check the power supply. working or not - Check the power level. properly Appliance is not - Check the power level. working - Is the kitchen properly ventilated? efficiently - Clean the grease filter. - At recirculation mode, check the carbon filter. - Check the air outlet. Light is not Check the bulb, see “Replacing the working bulb”. Oil is dripping Clean the grease filter. Brand BOMANN Model DU 770 G Annual Energy Consumption (AEChood) 33 kWh/a Energy Efficiency class

Fluid Dynamic Efficiency (FDEhood)

Fluid Dynamic Efficiency class

Lighting Efficiency (LEhood)

Lighting Efficiency class

Air flow at minimum speed in normal use Air flow at maximum speed in normal use NOTE: Air flow in use at intensive or If you are still having problems after following steps boost setting above, contact your trader or an authorized techni-

• - m³/h A-weighted sound power emission in normal use: cian. - at minimum speed - dB - at maximum speed 68 dB A-weighted sound power emission Technical Data in use at intensive or boost setting Electrical connecti connection………………………… ……… Power consumption in off mode (PO) Mains voltage: ………… ………………220-240 V~ Power consumption in standby Mains frequency: ………………………
• ……….50 Hz mode (PS) - dB N/A W Power consumption: …………………………… p. 93
• W This appliance has been tested according to all rele- Lighting, LED: ……………………………… x 1.5 W vant current CE guidelines, such as electromagnetic Protection class: ……………… ………………………I compatibility and low voltage directives, and has Dimension H x W x D / Weight …… ……………… been constructed in accordance with the latest safety Hood body: …… p. 2
• …………… p. 38
• .0 x 60.0 x 31.0 cm regulations. Telescopic shaft: ……… .0 – 73.0 x 20.0 x 17.8 cm Net weight: …………………….…… ….approx. 12.0 kg Available accessory………………………… ………… Activated carbon filter for recirculation mode: ………… KF 569 (Art.-No. 256 900) not supplied The right to make technical and design modifications in the course of continuous product development remains reserved. p. 40

Downloaded from www.Manualslib.com manuals search engine Disposal Meaning of the “Dustbin” Symbol Protect our environment; do not dispose of electrical equipment in the domestic waste. Please return any electrical equipment that you will no longer use to the collection points provided for their disposal. This helps avoid the potential effects of incorrect disposal on the environment and human health. This will contribute to the recycling and other forms of reutilization of electrical and electronic equipment. Information concerning where these can be disposed of can be obtained from your local authority.

Remove or disable any existing snap and bolt locks, if you take the unit out of operation or dispose it.