AHB1280IX - Kitchen hood AIRLUX - Free user manual and instructions

USER MANUAL AHB1280IX AIRLUX

RECOMMENDATIONS AND SUGGESTIONS 13

CHARACTERISTICS 16

INSTALLATION....17

USE 20

MAINTENANCE 21

SOMMAIRE

FR

CONSEILS ET SUGGESTIONS....23

CARACTERISTIQUES....26

INSTALLATION....27

UTILISATION 30

ENTRETIEN....31

ÍNDICE

PT

CONSELHOS E SUGESTÕES....33

CARACTERÍSTICAS 36

INSTALAÇÃO 37

UTILIZAÇÃO 40

MANUTENÇÃO 41

Illustration of a chemical experiment setup with a conical flask, beaker, and control panel (no text or symbols)

Diagram of a pipe connection with a 2° angle indicator, showing structural components without any text or symbols.

Illustration of a cooking setup with a pot and stove, featuring a crossed green pan and smoke (no text or symbols)

Simple line drawing of a T-shaped object with a vertical height dimension labeled 60 (no text or symbols beyond the measurement)

63 126 41 MIN.730-MAX.1000 540 B1 Min. 650mm Min. 650mm

470 260 300 598-698-760-898-1198

Componenti

Diagram showing a mechanical component with an arrow indicating direction, no text or symbols present

Montaggio Camino

Camino superiore

Illustration of a car interior with a fan and seat, showing no text or symbols

Illustration of a hand pressing down on a smartphone screen with a green arrow indicating the scroll (no text or symbols present)

Illustration of a hand pressing down on a device component with a green arrow symbol (no text or labels)

Illuminazione

The Instructions for Use apply to several versions of this appliance. Accordingly, you may find descriptions of individual features that do not apply to your specific appliance.

INSTALLATION

• The manufacturer will not be held liable for any damages resulting from incorrect or improper installation.
• The minimum safety distance between the cooker top and the extractor hood is 650 mm (some models can be installed at a lower height, please refer to the paragraphs on working dimensions and installation).
• Check that the mains voltage corresponds to that indicated on the rating plate fixed to the inside of the hood.
• For Class I appliances, check that the domestic power supply guarantees adequate earthing.
  Connect the extractor to the exhaust flue through a pipe of minimum diameter 120 mm. The route of the flue must be as short as possible.

- Do not connect the extractor hood to exhaust ducts carrying combustion fumes (boilers, fireplaces, etc.).

- If the extractor is used in conjunction with non-electrical appliances (e.g. gas burning appliances), a sufficient degree of aeration must be guaranteed in the room in order to prevent the backflow of exhaust gas. The kitchen must have an opening communicating directly

2°

with the open air in order to guarantee the entry of clean air. When the cooker hood is used in conjunction with appliances supplied with energy other than electric, the negative pressure in the room must not exceed 0,04 mbar to prevent fumes being drawn back into the room by the cooker hood.

- The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels (not applicable to appliances that only discharge the air back into the room).

- In the event of damage to the power cable, it must be replaced by the manufacturer or by the technical service department, in order to prevent any risks.

Illustration of a chemical experiment setup with a conical flask, thermometer, and smoke rising (no text or symbols)

• If the instructions for installation for the gas hob specify a greater distance specified above, this has to be taken into account. Regulations concerning the discharge of air have to be fulfilled.
• Use only screws and small parts in support of the hood.

Warning: Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards.

- Connect the hood to the mains through a two-pole switch having a contact gap of at least 3 mm.

USE

• The extractor hood has been designed exclusively for domestic use to eliminate kitchen smells.
• Never use the hood for purposes other than for which it has been designed.
• Never leave high naked flames under the hood when it is in operation.
• Adjust the flame intensity to direct it onto the bottom of the pan only, making sure that it does not engulf the sides.
• Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames.
• Do not flambè under the range hood; risk of fire.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of

Illustration of a cooking setup with a pot and stove, featuring a crossed green pan and smoke (no text or symbols)

experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

- "CAUTION: Accessible parts may become hot when used with cooking appliances."

MAINTENANCE

• Switch off or unplug the appliance from the mains supply before carrying out any maintenance work.
• Clean and/or replace the Filters after the specified time period (Fire hazard).
• The Grease filters must be cleaned every 2 months of operation, or more frequently for particularly heavy usage, and can be washed in a dishwasher.
• The Activated charcoal filter is not washable and cannot be regenerated, and must be replaced approximately every 4 months of operation, or more frequently for particularly heavy usage.
• "Failure to carry out cleaning as indicated will result in a fire hazard".
• Clean the hood using a damp cloth and a neutral liquid detergent.

The symbol ☒ on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

Dimensions

Simple line drawing of a T-shaped object with a vertical height dimension labeled 60 (no text or symbols beyond the measurement)

63 126 41 MIN.730-MAX.1000 540 B1 Min. 650mm Min. 650mm

470 260 300 598-698-760-898-1198

Components

Ref.	Q.ty	Product Components
1	1	Hood Body, complete with: Controls, Light, Blower, Filters
2	1	Telescopic Chimney comprising:
2.1	1	Upper Section
2.2	1	Lower Section
9	1	Reducer Flange ø 150-120 mm
10	1	Damper ø 150
15	1	Air Outlet Connection
Ref.	Q.ty	Installation Components
7.2.1	2	Upper Chimney Section Fixing Brackets
11	6	Wall Plugs
12a	6	Screws 4,2 x 44,4
12c	6	Screws 2,9 x 9,5
	Q.ty	Documentation
	1	Instruction Manual

1 2 2.1 2 2.2 9 10 15 12a 7.2.1 11 12c 11 12a 1

Wall drilling and bracket fixing

7.2.1 1÷2 X 11 116 116 12a 320 650 min.

Wall marking:

• Draw a vertical line on the supporting wall up to the ceiling, or as high as practical, at the centre of the area in which the hood will be installed.
• Draw a horizontal line at 650 mm above the hob. Place bracket 7.2.1 on the wall as shown about 1-2 mm from the ceiling or upper limit aligning the centre (notch) with the vertical reference line.
• Mark the wall at the centres of the holes in the bracket.
• Place bracket 7.2.1 on the wall as shown at X mm below the first bracket (X = height of the upper chimney section supplied), aligning the centre (notch) with the vertical line.
• Mark the wall at the centres of the holes in the bracket.
• Mark a reference point as indicated at 116 mm from the vertical reference line and 320 mm above the horizontal reference line.
• Repeat this operation on the other side.
• Drill 8 mm holes at all the centre points marked.
• Insert the wall plugs 11 in the holes.
  • Fix the brackets using the 12a (4,2 x 44,4) screws supplied.

• Insert the two screws 12a (4,2 x 44,4) supplied in the hood body fixing holes, leaving a gap of 5-6 mm between the wall and the head of the screw.

• Before attaching the hood body, tighten the two screws Vr located on the hood body mounting points.

• Hook the hood body onto the screws 12a.
  • Fully tighten the support screws 12a.
• Adjust the screws Vr to level the hood body.

12a Vr

Connections

DUCTED VERSION AIR EXHAUST SYSTEM

When installing the ducted version, connect the hood to the chimney using either a flexible or rigid pipe 150 or 120mm, the choice of which is left to the installer.

To install a ∅ 150 pipe

• To install the dumper 10
- Fix the pipe in position using sufficient pipe clamps (not supplied).

To install a ∅ 120 pipe

• To install a 120 mm air exhaust connection, insert the reducer flange 9 on the dumper 10.
• Fix the pipe in position using sufficient pipe clamps (not supplied).
• Remove any activated charcoal filters.

ø 150 ø 120 10 9 10

AIR OUTLET - RECIRCULATION VERSION

• Unfasten the 2 screws fixing the upper bracket 7.2.1.
• Fasten the air outlet connector 15 in its place, using the 2 screws removed as above.
• Join the Connector 15 to the Hood canopy outlet using a rigid or flexible pipe 150mm , selection of which is at the discretion of the installation technician.
• Make sure that the Activated charcoal odour filter has been fitted.

7.2.1 15 Ø 150

ELECTRICAL CONNECTION

• Connect the hood to the mains through a two-pole switch having a contact gap of at least 3 mm.
• Remove the grease filters (see paragraph Maintenance) being sure that the connector of the feeding cable is correctly inserted in the socket placed on the side of the fan.

Diagram showing a mechanical component with an arrow indicating direction, no text or symbols present

Flue assembly

Upper exhaust flue

• Slightly widen the two sides of the upper flue and hook them behind the brackets 7.2.1, making sure that they are well seated.
• Secure the sides to the brackets by using the 4 screws 12c (2,9 x 9,5) supplied.
• Make sure that the outlet of the extensions pieces is aligned with the chimney outlets.

Lower exhaust flue

• Slightly widen the two sides of the flue and hook them between the upper flue and the wall, making sure that they are well seated.
• Fix the lower part laterally to the hood body by using the 2 screws 12c (2,9 x 9,5) supplied.

7.2.1 12c 2.1 2 2.2 12b

Control panel

Button	Function	Display
A	Turns the suction motor on and off at speed one.	Displays the set speed
B	Decreases the working speed.	Displays the set speed
C	Increases the working speed.	Displays the set speed
D	Activate intensive speed from any other speed, including motor off. This speed is set to operate for 6 minutes, after which the system returns to the speed that was set before. Suitable to deal with maximum levels of cooking fumes.	Displays HI and the time remaining once very second.
	Press and hold the button for approximately 5 seconds, with all the loads turned off (Motor and Lights), to turn the Activated Charcoal Filter alarm On and Off.	FC+Punto (2 flashes)-Alarm On.FC+Punto (1 flash)-Alarm Off.
E	24H functionTurns the suction motor on at speed one and effects one 10 minute extraction every hour.	Displays 24 and the spot at the bottom right flashes once every second, while the motor is running.It is disabled by pressing the button.
	When the filters alarm is triggered, the alarm can be reset by pressing and holding this button for approximately 3 seconds.These indications are only visible when the motor is turned off.	FF flashes three times.When the procedure terminates, the indication shown previously turns off:FG indicates the need to wash the metal grease filters. The alarm is triggered after the Hood has been in operation for 100 working hours.FC indicates the need to change the activated charcoal filters, and also to wash the metal grease filters. The alarm is triggered after the Hood has been in operation for 200 working hours.
F	Delay functionActivate automatic switch-off with a 30' delay. Suitable to complete elimination of residual odours. Can be activated from any position, and is disabled by pressing the button or turning the motor off.	Displays the operating speed and the spot at the bottom right flashes once a second.
	Press and hold the button for approximately 5 seconds, with all the loads turned off (Motor and Lights), to turn the Remote Control On and Off.	IR+Punto (2 flashes)-Alarm On.IR+Punto (1 flash)-Alarm Off.
G	Turns the lighting system on and off at maximum intensity.
H	By pressing this key the intensity of the lighting system change cyclically through Off.

REMOTE CONTROL (OPTIONAL)

The appliance can be controlled using a remote control powered by a 1.5 V carbon-zinc alkaline batteries of the standard LR03-AAA type (not included).

• Do not place the remote control near to heat sources.
  • Used batteries must be disposed of in the proper manner.

Illustration of a car interior with a fan and seat, showing no text or symbols

Metal grease filters

They can be washed in the dishwasher, and need to be cleaned whenever the FG sign appears on the display or at least once every 2 months use, or more frequently if use is particularly intensive.

Resetting the alarm signal

• Turn the Lights and the Suction motor off, then disable the 24h function, if enabled.
• Press button E (see the paragraph on Use).

Cleaning the Filters

• Remove the Filters one at a time, pushing them towards the back of the unit and at the same time pulling downward.
• Wash the Filters without bending them, and leave them to dry completely before replacing. (If the surface of the filter changes colour as time goes by, this will have absolutely no effect on the efficiency of the filter itself.)
• Replace, taking care to ensure that the handle faces forwards.

Illustration of a hand pressing down on a smartphone screen with a green arrow indicating the scroll (no text or symbols present)

It cannot be washed or regenerated, and must be changed when the FC symbol on the display appears, or at least once every 4 months. The Alarm signal, if it has been activated, only appears when the Suction motor is turned on.

Activating the alarm signal

• In Recirculation Version Hoods, the Filter Saturation Alarm must be activated on installation or at a later date.
• Turn the Lights and the Suction Motor off.
• Press D and hold for approximately 5 Seconds:
• The message FC+Dot flashes twice, A.C. Filter saturation alarm ACTIVATED
• The message FC+Dot flashes once, A.C. Filter saturation alarm DEACTIVATED

CHANGING THE ACTIVATED CHARCOAL FILTER

Resetting the alarm signal

• Turn the Lights and the Suction motor off, then disable the 24h function, if enabled.
• Press button E (see the paragraph on Use).

Changing the Filter

• Remove the Metal grease filters.
• Remove the saturated charcoal filter by releasing the fixing hooks.
• Fit the new filter and fasten it in its correct position.
• Replace the Metal grease filters.

Illustration of a hand pressing down on a mechanical component with a green arrow indicating downward motion (no text or symbols)

Lighting unit

- For replacement contact technical support ("To purchase contact technical support").

Illustration of a laboratory setup with a conical flask, test tube, and control panel emitting vapor (no text or symbols)

2°

Illustration of a greenhouse with a stove and fire extinguisher crossed out by a green ribbon (no text or symbols)

Simple line drawing of a T-shaped object with a vertical height dimension labeled 60 (no text or symbols beyond the measurement)

63 126 41 MIN.730-MAX.1000 540 B1 Min. 650mm Min. 650mm

470 260 300 598-698-760-898-1198

Composants

Diagram showing a mechanical component with an arrow indicating direction, no text or symbols present

Montage Cheminée

Cheminée supérieure

Illustration of a car interior with a fan and seat, showing no text or symbols

Illustration of a hand pressing a green arrow on a smartphone screen (no text or symbols)

REPLACEMENT DU FILTRE ANTI-ODEUR AU CHARBON ACTIF

Illustration of a hand inserting a component into a device, with a green arrow indicating direction (no text or symbols)

Éclairage

Illustration of a chemical experiment setup with a funnel, beaker, and control panel (no text or symbols)

2°

Illustration of a cooking setup with a pot, steam rising, and flames under a banner (no text or symbols)

Simple line drawing of a T-shaped object with a vertical height dimension labeled 60 (no text or symbols beyond the measurement)

63 126 41 MIN.730-MAX.1000 540 B1 Min. 650mm Min. 650mm

470 260 300 598-698-760-898-1198

Componentes

Diagram showing a mechanical component with an arrow indicating direction, no text or symbols present

Montagem da chaminé

Illustration of a car interior with a fan and seat, showing no text or symbols

Filtros metálicos antigordura

Illustration of a hand interacting with a smartphone screen showing a green arrow (no text or symbols present)

Illustration of a hand pressing down on a mechanical component with a green arrow symbol (no text or labels)

Iluminação