D10-2W - Blender BRABANTIA - Free user manual and instructions

USER MANUAL D10-2W BRABANTIA

We hope it will delight you and that it will get a special place in your home. Enjoy!

EN

IMPORTANT SAFEGUARDS

1. Please read through the following safety precautions carefully before switching on the Table Blender.
2. Keep this instruction manual in a safe place for future reference. Also keep the sales receipt and, if possible, the gift box with the inner packaging.
3. Failure to follow all the instructions listed may result in electric shock, fire or serious personal injury.
4. Before plugging the Table Blender into the mains electrical supply, check that the voltage and power supply comply with the specifications indicated on the rating plate of the Table Blender.
5. Do not plug the Table Blender into the power supply until it is fully assembled and always unplug before disassembling the Table Blender or handling the blade.
6. The Table Blender is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the Table Blender by a person responsible for their safety.
7. Always place the Table Blender on a stable, flat, heat-resistant surface. Also ensure that the surface can take the weight of the unit during use.
8. The Table Blender is intended for domestic use only and should not be used for commercial purposes. The Table Blender should only be used for its intended purpose.
9. Always keep the Table Blender out of the reach of children. Close adult supervision is necessary when the Table Blender is used by or near children.
10. Do not leave the unit unattended when not in use.
11. Do not move or lift the Table Blender while it is operating or while it is connected to an electrical socket.
12. The use of attachments, not specifically recommended by the manufacturer, must not be used as they may cause personal injury or damage to the Table Blender.
13. Care should be taken when handling the sharp cutting blades, emptying the jug and during cleaning.
14. When mixing hot liquid or food, excess pressure may build up inside the Table Blender and this may cause the lid to come off and the contents to splash out. Avoid mixing excessively lukewarm food and only place small quantities of lukewarm liquid or food inside the Table Blender.
15. Do not use the Table Blender for very hard food products such as bones, shelled nuts, frozen meat etc., as this may damage the blade or cause the motor to seize.

16. The blades of the jug are very sharp. Never touch the inside of the jug or place any objects in the jug while the blades are turning.

17. The Table Blender is equipped with a safety function. The unit can only be switched on if the jug is placed properly on the base and it is locked into position. If the Table Blender cannot be switched on, remove the plug from the mains power supply and check the connection between jug and base. Make sure that the glass jug is properly locked into position before attempting to start operation.

18. Only start operating the Table Blender once the lid is tightly placed onto the glass blending jug and the measuring cup has been inserted into the lid.
19. Do not operate the Table Blender if the plug or power cord has been damaged, is not working properly, has been dropped or has been exposed to water or other liquid.
20. Check the Table Blender power cord regularly for damage. If the power cord is damaged in any way, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid an electrical hazard.
21. Do not allow the power cord to hang over sharp table edges or come into contact with hot surfaces.
22. Make sure that the Table Blender is switched off and remove the plug from the mains electrical supply when it is not in use, before it is cleaned, before changing accessories or moving parts and while it is being repaired.
23. Take care when handling the sharp blades, when emptying the glass jug and during the cleaning process.
24. Avoid potential injury through misuse.
25. To prevent the risk of electrical shock, do not immerse the power cord, plug, or any non-removable parts of this Table Blender in water or any other liquid.
26. The Table Blender base must not be submerged in water, as any contact with the electrical parts will create a malfunction and/ or an electric shock. Do not use the Table Blender with wet hands.
27. Do not use the Table Blender outdoors.
28. Always turn the dial to position 'O' to switch off the unit before removing the plug from the wall socket.
29. To unplug the Table Blender, grasp the plug firmly and remove it from the mains electrical supply. Do not pull on the cord or carry the unit by its cord.
30. Never use the Table Blender if it is damaged in any way.
31. Use only spare parts supplied by the manufacturer or an authorised service centre.
32. All repairs may only be carried out by an authorised service centre. Improper repairs may place the user at risk.
33. When handing the Table Blender over to a third party, ensure that this instruction manual is supplied with the Table Blender.

KNOW YOUR TABLE BLENDER

1. Measuring Cup
2. Cover lid
3. Glass Jar
4. Blade assembly
5. Smoothie button
6. Ice crushed button
7. Pulse button
8. Base Unit
9. Control Knob
10. Indication light

DOUBLE SAFETY LOCKING SYSTEM

This system ensures user can only switch the Table Blender on when the lid has been placed and locked on the unit in correct position. The Table Blender can only be switched on, when the accessories have been fixed properly.

BEFORE FIRST USE

Clean the Table Blender and parts thoroughly before you use the appliance for the first time.

1. Wash the measuring cup, lid and glass blender jug before first use.
2. Ensure that the Table Blender is off and not connected to the mains electrical supply before assembling.
3. Insert the glass blender jug into the blade base and then adjust the glass blender jug so that it is locked into the blade base.
4. Place the lid on top of the glass blender jug and press down.
5. Place the measuring cup in the centre of the lid and turn it anti-clockwise to lock it into the lid.

This is normal that the cover lid is a bit tight to remove from glass jug (under dry condition) because of the secure sealing system. The lid would be easy to manage after blending any kind of liquid ingredient

CAUTION: The blades are very sharp. Wash with care. Never touch the blade with your finger.

1. Screw the blade assembly unit to the glass jug bottom until it is fixed properly.
2. Place the glass jug with blade assembly unit interface on the motor unit.
3. Place the lid on the jug and lock onto the handle.
4. Insert the measuring cup into the lid opening
5. Connect to main power supply.
6. Select the speed by turning the knob or press the program button.

IMPORTANT: Never operate the blender when it is empty or if it is filled with solids. Do not let the appliance operate more than 3 minutes continuously. Let the appliance cool down to room temperature before operating the appliance again.

USING THE TABLE BLENDER

1. To switch on the appliance, turn the knob (9) to "ON" position. The Indication light (10) will be illuminated.
2. To use the programmed function, turn the knob to "ON" position. The light on the three buttons (5, 6, 7) will be illuminated. Press the programmed button, the light on the specific button will be illuminated. When the program finished, the unit will back to standby mode.
3. To control the rotary speed, turn the knob between "MIN" & "MAX" position.

Crush ice button

Press this button to crush the ice. The appliance starts crushing according to the pre-set speed profile. The unit will stop automatically after the end of program. Press the button again during operation will terminate the program and back to standby mode.

Smoothie button

Press this button to make delicious smoothies. The appliance starts mixing according to the pre-set speed profile. The unit will stop automatically after the end of program. Press the button again during operation will terminate the program and back to standby mode.

Pulse button

Press this button to run the pulse mode. The unit operates only when pulse button was pressed.

Tips

1. Do not blend dry, thick or heavy mixtures for more than 10 seconds continuously. Let the appliance cool down to room temperature before continue operating the appliance again.
2. Blend Ice, not more than 2 seconds continuously.
3. Do not place the lid into a dishwasher or boiling water, the lid may deform. Clean the attachment by warm water is recommended.
4. Always hold the edge of the lid while operating the blender.
5. After every max operation period, please let the appliance cool down to room temperature before continue operating the appliance again.

CLEANING AND MAINTENANCE

Disassembling and cleaning the Table Blender

1. Put the base unit (8) on a flat, dry table. Ensure that the control knob(9) is in the off position and that the power cord is unplugged.

2. Hold the base unit with one hand and with the other hand lift up the glass jug (3).

3. Remove the jug lid from the glass jug.

The blender jug can be cleaned without disassembling

1. Fill in the glass jug half-full of Warm water and little cleaning agent. Let the Table Blender run on min speed until the jug is cleaned.
2. Clean the glass jug (3), lid (2), measuring cup (1) and blade unit with the seal ring with Warm water and some cleaning agent. Dry before using.

NOTE:

1. Do not clean the stainless steel base unit, power cord and plug with water. Wipe it with a soft, moist cloth and some cleaning agent. Wipe with a dry cloth.
2. Never use aggressive cleaning agents.
3. Ensure that the glass jug is completely empty before you unscrew the retaining ring. Be careful when handling the blade.

SPECIFICATIONS

220V-240V 50/60Hz

Rated power: 1000W

Capacity: 1.5L

Operating time: 3 minute cycles of continuous operation only

ENVIRONMENT FRIENDLY DISPOSAL

C

This marking indicates that this product should not be disposed of with other household waste. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable re-use of material resources. To dispose of your appliance correctly, please contact or take it to your local refuse/recycling centre. Alternatively,

contact your local council for information on your local re-use centre.

WARRANTY

IMPORTANT: In order for your warranty to be valid, you must keep your sales receipt. A warranty CANNOT be claimed without proof of purchase.

We also highly recommend that you keep both your instruction manual and original packaging. The original packaging will prove useful if you need to return your product.

Warranty exclusions:

The warranty will not be valid if:

1. The product has not been installed, operated or maintained in accordance with the manufacturer's operating instructions provided with the product.
2. The product has been used for any purpose other than its intended function.
3. The damage or malfunction of the product is caused by any of the following:

Incorrect voltage
- Accidents (including liquid or moisture damage)
- Misuse or abuse of the product
- Faulty or improper installation
- Mains supply problems, including power spikes or lightning damage
- Infestation by insects
- Tampering or modification of the product by persons other than authorised service personnel
- Exposure to abnormally corrosive materials
- Insertion of foreign objects into the unit
Usage with accessories not pre-approved by Brabantia
- General wear and tear, including, but not limited to, minor discolouration and scratches

Please refer to and heed all warnings and precautions in this Instruction Manual.

Due to continuous product development, specifications may be subject to change without prior notification.

NL

BELANGRIJKE VEILIGHEIDSMAATREGELEN

EXCLUSIONS DE GARANTIE

Should you experience any technical difficulty in setting up or using your new product, please feel free to contact our dedicated customer service help desk.

For customers from Netherlands and Belgium please contact Elmarc B.V.

Elmarc B.V.
Kolenbranderstraat 28
2984 AT RLdderkerk
Tel: (NL) 09003555333
(BE) 070355505
E-mail: [e-mail]

RANKSHARP

Manufactured by Rank Sharp Industries under exclusive licence of Brabantia Nederland B.V.

Rank Sharp Industries, 11th Floor, SML Tower, 165 Hoi Bun Road, Kwun Tong, Kowloon, Hong Kong

PRODUCT INFORMATION

D10-2W TABLE BLENDER