CGIS3065PF - Fridge FRIGIDAIRE - Free user manual and instructions

USER MANUAL CGIS3065PF FRIGIDAIRE

INSTALLATION INSTRUCTIONS

30" FRONT CONTROL FREESTANDING RANGE

• INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER. IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. United States Canada FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Table of Contents Important Notes to the installer p. 1
• Important Note to the Customer p. 1

1. Clearances and Dimensions.................................2

2. Tools You Will Need..............................................3

3. Anti-tip Bracket Installation Instructions

Important Safety Warning...............................3-4 Important Notes to the Installer

1. Read all instructions contained in these

installation instructions before installing range.

2. Remove all packing material from the oven and

the drawer compartments before connecting the electrical supply to the range.

3. Observe all governing codes and ordinances.

4. Be sure to leave these instructions with the

consumer. Important Note to the Consumer Keep these instructions with your owner's guide for future reference. Printed in U.S.A. Tip Over Hazard

• A child or adult can tip the range and be killed.
• Verify the anti-tip device has been installed to floor or wall.
• Ensure the anti-tip device is re-engaged to floor or wall when the range is moved.
• Do not operate the range without the anti-tip device in place and engaged.
• Failure to follow these instructions can result in death or serious burns to children and adults. To check if the anti-tip bracket is installed properly, use both arms to grasp the rear edge of the range back. Carefully attempt to tilt range forward. When properly installed, the range should not tilt forward. Refer to the anti-tip bracket installation instructions supplied with your range for proper installation. P/N 809127101 (1511) Rev. B English – pages 1-8 Spanish - pages 9-16 Français – pages 17-24

30" ELECTRIC RANGE INSTALLATION INSTRUCTIONS

1. Clearances and Dimensions

a. Provide adequate clearances between the range and adjacent combustible surfaces. b. Location—Check location where the range will be installed. Check for proper electrical supply and the stability of floor. c. Dimensions that are shown must be used. Given dimensions provide minimum clearance. Contact surface must be solid and level. Front view Typical cabinet installation Side view 29 7/8" 30” Minimum

Minimum to wall on either side of range above 36” height. 30” Minimum* 18” Minimum to cabinets on either side of range 13” Maximum depth for cabinets above range top. 36 3/8" ± 1/4" Maximum 25” Max. 36” 30” Minimum 26" 0” clearance below cooking top and at rear of range

• 30" minimum clearance between the top of the cooking surface and the bottom of an unprotected wood or metal cabinet; or 24 " minimum when bottom of wood or metal cabinet is protected by not less than ¼" flame retardant millboard covered with not less than no. 28 MSG sheet steel, 0.015" stainless steel, 0.024" aluminum or 0.020" copper. The minimum clearance is 0" for the rear of the range. Follow all dimension requirements provided above to prevent property damage, potential fire hazard, and incorrect countertop and cabinet cuts. BACK VIEW All dimensions for electrical outlet location are maximum. Terminal Block Location Cubed area shows where the electrical outlet must be installed for the range to be flush to the wall.

Avoid locating cabinet storage space above the surface units to eliminate the possibility of cabinets catching on fire, or personal burns from reaching for the cabinets over the heated units. If cabinet storage is to be provided, risk can be reduced by installing a range hood that projects horizontally a minimum of 5" beyond the bottom of the cabinets. 2½”

30" ELECTRIC RANGE INSTALLATION INSTRUCTIONS

2. Tools You Will Need

Tip Over Hazard For leveling legs and Anti-Tip Bracket:

• A child or adult can tip the range and be killed.
• Verify the anti-tip device has been installed to floor or wall as per installation instructions.
• Ensure the anti-tip device is re-engaged to floor or wall when the range is moved.
• Do not operate the range without the anti-tip device in place and engaged.
• Failure to follow these instructions can result in death or serious burns to children and adults.

• Adjustable wrench or channel lock pliers
• 5/16" Nutdriver or Flat Head Screwdriver
• Electric Drill & 1/8" Diameter Drill Bit (Masonry Drill Bit if installing in concrete)
• Level & Measuring Tape For electrical supply connection:
• 1/4" & 3/8" Socket driver or Nutdriver Additional Materials You Will Need:
• Power Supply Cord or
• Copper Electrical Wiring & Metal Conduit (for hard wiring) Range Leveling Leg

3. Anti-tip Bracket Installation Instructions

Important Safety Warning To reduce the risk of tipping of the range, the range must be secured to the floor by the properly installed anti-tip bracket and screws packed with the range. Failure to install the anti-tip bracket will allow the range to tip over if excessive weight is placed on an open door or if child climbs upon it. Serious injury might result from spilled hot liquids or from the range itself. If range is ever moved to a different location, the anti-tip brackets must also be moved and installed with the range. Instructions are provided for installation in wood or cement floor. When fastening to floor, be sure that screws do not penetrate electrical wiring or plumbing. To check if the anti-tip bracket is installed properly, use both arms and grasp the rear edge of range back. Carefully attempt to tilt range forward. When properly installed, the range should not tilt forward. A. Locate the Bracket Using the Template - Locate the bracket position (right or left side) by placing the template symmetrically to the center of the final range position. Mark the location of the screw holes, shown on template. Figure 1

30" ELECTRIC RANGE INSTALLATION INSTRUCTIONS

B. Drill Pilot Holes and Fasten Bracket - Drill a 1/8" pilot hole where screws are to be located. If bracket is to be mounted to the wall, drill pilot hole at an approximate 20° downward angle. If bracket is to be mounted to masonry or ceramic floors, drill a 3/16" pilot hole 1-3/4" deep. The screws provided may be used in wood or concrete material. Use a 5/16" nut-driver or flat head screwdriver to secure the bracket in place. C. Level and position the range - Slide range to its final position. Insert the range leveling leg in the antitip bracket. Visually verify if the anti-tip bracket is engaged. Lower the range by adjusting the 4 leveling legs alternatively until the range is level. Check if the range is level by placing a spirit level on the oven rack. Take 2 readings with the spirit level placed diagonally; take a reading in one direction and then in the other direction. Level the range if necessary by adjusting the leveling legs. FASTEN BRACKET (WALL OR FLOOR MOUNTING) 1-1/4” Max. Rear of Range Leveling leg Wall mount Wall Plate Floor Mount FASTEN BRACKET (FLOOR MOUNTING ONLY) Rear of Range Leveling leg Floor Mount Figure 3 More than 1-1/4” Wall Leg Leveler Raise Lower Figure 5

30" ELECTRIC RANGE INSTALLATION INSTRUCTIONS

4. Serial Plate Information

5.2 Models Requiring Power Supply Cord Kit

The serial plate is located as shown. See the serial plate for the following information: A. Model, lot and serial number of range. B. Kilowatt rating (power requirements). C. Voltage ratings. Figure 6 Figure 7B – 3-Wire Cord Kit The user is responsible for connecting the power supply cord to the connection block located behind the back panel access cover. This appliance may be connected by means of permanent "hard wiring"; flexible armored or nonmetallic shielded copper cable (when local code allow it) or by means of a power supply cord kit. NOTE: Electric slide-in range is shipped from factory with 1 1/8" (2.9 cm) dia. hole as shown on figure 9. If a larger hole is required, punch out the knockout. Risk of fire or electrical shock exists if an incorrect size range cord kit is used, the Installation Instructions are not followed, or the strain relief bracket is discarded. For mobile homes, new installation or recreational vehicles, use only a power cord kit design for a range at 125V /250V 50A recommended (minimum 40A). Cord must have either 3 (when local code permits grounding through neutral) or 4 conductors. Terminal on end of wires must be either closed loop or open spade lug with upturned ends. Cord must have strain-relief clamp. If a 50A circuit is used, a 50A power cord must be used. Do not loosen the nuts which secure the factory-installed range wiring to terminal block while connecting range. Electrical failure or loss of electrical connection may occur.

5. Electrical Connection Requirements

(Canada only) Plug the range cable (4 conductors) into a 4 conductor range outlet. Outlet must be properly grounded and in accordance with the Canadian Electrical Code (CSA Standard (C22.1 Part 1 - latest edition)- and any local electrical code requirements. Canada Style Figure 7A

5.1 Electrical Connection Requirements

(U.S.A. only) This appliance must be properly installed and grounded by a qualified technician in accordance with the National Electrical Code ANSI/NFPA No. 70-latest edition- and local electrical code requirements. This appliance may be connected by means of permanent "Hard Wiring" or "Power Supply Cord Kit." When hard wiring, do not leave excess wire in range compartment. Excess wire in the range compartment may not allow the access cover to be replaced properly, and could create a potential electrical hazard if wires become pinched. When using flexible conduit or range cable, use flex connector or range cable strain relief. NOTE: Only use copper wire in connection to terminal block. Electrical Shock Hazard

• Electrical ground is required on this appliance.
• Do not connect to the electrical supply until appliance is permanently grounded.
• Disconnect power to the circuit breaker or fuse box before making the electrical connection.
• This appliance must be connected to a grounded, metallic, permanent wiring system, or a grounding connector should be connected to the grounding terminal or wire lead on the appliance. Failure to do any of the above could result in a fire, personal injury or electrical shock.

30" ELECTRIC RANGE INSTALLATION INSTRUCTIONS

Four Conductor Wire Connection to Range This appliance is manufactured with the frame grounded by connection of a grounding strap between the neutral power supply terminal and the frame. If used in USA, in a new branch circuit installation (1996 NEC), mobile home or recreational vehicle, where local code do not permit grounding through neutral (white) wire or in Canada; remove the grounding strap from the frame and cut the other end, near the neutral terminal. Connect the appliance in usual manner. Where local codes does NOT permit connection of the frame grounding conductor to the neutral wire of the copper power supply cord (see Figure 9):

1. Remove the screws from the access plate at

the lower right end of the rear cover to expose range terminal connection block.

2. Remove the grounding strap from the terminal

block and from the appliance frame.

3. Using the nuts supplied with the literature

package, connect the ground wire (green) of the copper power supply cord to the frame of the appliance with the ground screw, using the hole in the frame where the ground strap was removed (see Figure 9).

4. Connect the neutral of the copper power supply

cord to the center silver-colored terminal of the terminal block, and connect the other wires to the outer terminals. Match wires and terminals by color (red wires connected to the right terminal, black wires connected to the left terminal).

5. Replace the terminal cover and replace the

screws. Three Conductor Wire Connection to Range If local codes permit connection of the frame grounding conductor to the neutral wire of the copper power supply cord (see Figure 8):

1. Remove the screws from the access plate at

the lower right end of the rear cover to expose range terminal connection block.

2. Using the nuts supplied in the literature

package, connect the neutral of the copper power supply cord to the center silver-colored terminal of the terminal block, and connect the other wires to the outer terminals. Match wires and terminals by color (red wires connected to the right terminal, black wires connected to the left terminal) (see Figure 8).

3. Replace the terminal cover and replace the

screws. Silver Colored Terminal Red Wire Black Wire 1 1/8" (2.9cm) Dia. Direct Connection Hole. Punch Out Knockout for 1 3/8" (3.5cm) Dia. Cord Kit Hole. Neutral (White Wire) Black Wire A User Supplied Strain-relief Must Be Installed at This Location. Red Wire Cord Mounting Plate Terminal Block A User Supplied Strain-relief Must Be Installed at This Location Grounding Strap Silver Colored Terminal Terminal Block Neutral (White Wire) Ground (Bare Copper Wire) NOTE: Be sure to remove the supplied grounding strap. 1 1/8" (2.9 cm) Dia. Direct Connection Hole. Punch Out Knockout for 1 3/8" (3.5 cm) Dia. Cord Kit Hole. Figure 9

30" ELECTRIC RANGE INSTALLATION INSTRUCTIONS

Direct Electrical Connection to the Circuit Breaker, Fuse Box or Junction Box Where local codes DO NOT permit connecting the appliance-grounding conductor to the neutral (white) wire, or if connecting to 4-wire electrical system (see Figure 11):

1. Be sure that no power is supplied on the cable

2. Follow instructions on previous page for Four

Conductor Wire Connection to Range (Fig. 9).

3. In the circuit breaker, fuse box or junction box

(Fig. 11): a) Connect the white appliance cable wire to the neutral (white) wire. b) Connect the 2 black wires together. c) Connect the 2 red wires together. d) Connect the green (or bare copper) grounding wire to the grounding wire of the circuit breaker, fuse box or junction box. If the appliance is connected directly to the circuit breaker, fuse box or junction box, use flexible, armored or nonmetallic sheathed copper cable (with grounding wire). Supply a U.L. listed strainrelief at each end of the cable. At the appliance end, the cable goes through the Direct Connection Hole (see Figure 9) on the Cord Mounting Plate. Wire sizes (copper wire only) and connections must conform to the rating of the appliance. Where local codes permit connecting the appliance-grounding conductor to the neutral (white) wire (see Figure 10):

1. Be sure that no power is supplied on the cable

2. Follow instructions on previous page for Four

Conductor Wire Connection to Range (Fig. 9).

3. In the circuit breaker, fuse box or junction box

(Fig. 10): a) Connect the green (or bare copper) wire, the white appliance cable wire, and the neutral (white) wire together. b) Connect the 2 black wires together. c) Connect the 2 red wires together. Green (or Bare Copper) Wire Black Wires Green (or Bare Copper) Wire Black Wires Junction Box Cable from Appliance Cable from Appliance White Wire U.L.-listed Conduit Connector (or CSA listed) NOTE: Be sure to remove the supplied grounding strap. Junction Box White Wire Green (or Bare Copper) Wire White Wire Red Wires Cable from Residence Neutral (white) Wire Red Wires Cable from Residence Figure 11 4-Wire Electrical System (Example: Junction Box) U.L.-listed Conduit Connector (or CSA listed)

6. Checking Operation

Refer to the Use and Care Guide for operation. CAUTION Do not touch cooktop glass or elements. They may be hot enough to burn you. NOTE: Be sure to remove the supplied grounding strap. Before You Call for Service Read the Before You Call for Service Checklist and operating instructions in your Use and Care Guide. It may save you time and expense. The list includes common occurrences that are not the result of defective workmanship or materials in this appliance. Refer to your Use and Care Guide for Sears service phone numbers, or call 1-800-4-MY-HOME®. Figure 10 3-Wire (Grounded Neutral) Electrical System (Example: Junction Box)

NOTES P/N 809127101 (1511) Rev. B English – pages 1-8 Spanish - pages 9-16 Français – pages 17-24 36 3/8" ± 1/4" Maxima 25” Max. 36” 30” Minimum 26" 0” clearance below cooking top and at rear of range

ert 46" bre Estufa Range lado side Montura antivuelco Figura 3 P/N 809127101 (1511) Rev. B English – pages 1-8 Spanish - pages 9-16 Français – pages 17-24 29 7/8" 30" 30” Minimum

30" Minimum* 30” Minimum* 18” 36 3/8" ± 1/4" Maximum 25” Max. 36” 30" 30 1/8” Minimum 26" Support anti-bascule Support anti-bascule Figure 3 FIXER LE SUPPORT (MONTAGE AU PLANCHER SEULEMENT) More than 1-1/4” Rear of Range Support anti-bascule Figure 2 Figure 4