889AE - Hair styling tool BABYLISS - Free user manual and instructions

Brand	BaByliss
Model	889AE
Product type	Professional hair dryer hood
Use	Drying and styling hair
Power supply	Mains, suitable for the voltage indicated on the appliance
Power	Approximately 1000 W (estimate)
Adjustable height	Yes, by sliding the upper tube (range not specified, approximately 30-60 cm)
Weight	Approximately 2 kg (estimate)
Drying positions	III (fast), II (normal), I (cold air)
Start	Automatic by lowering the visor
Stop	Automatic by raising the visor
Adjustable diffuser	Yes, button at the front inside to direct the airflow
Safety system	Safety thermostat (automatic shut-off in case of overheating)
Removable filter	Yes, clean regularly
Lower tube material	Plastic
Feet	4 feet (1 non-weighted, 3 weighted)
Hood attachment	On the upper tube with a 12 mm screw
Cord length	Approximately 2 m (estimate)
Maintenance	Soft damp cloth with mild detergent; do not immerse
Included accessories	30 mm screw, 12 mm screw, plastic hook for the cord
Manual pages	53 pages
Warranty	Compliant with directives 89/336/EEC and 73/23/EEC

Frequently Asked Questions - 889AE BABYLISS

How to assemble the BaByliss 889AE hairdryer hood?

First, slide the non-weighted foot into the longest hole and secure it with the 30 mm screw. Insert the three weighted feet into their holes. Then, insert the lower plastic tube into the base segment and tighten. Loosen the locking ring, pull the upper tube to the desired height, then retighten. Attach the hood to the upper tube with the 12 mm screw. Add the hook for the power cord.

How to adjust the height of the hood?

Use the locking ring (7): loosen it by turning counterclockwise, slide the upper tube to the desired height, then retighten the ring.

What drying positions are available?

The switch on the side of the hood offers three positions: Position III for fast drying, Position II for normal drying, and Position I for cold air to set the style.

How to start and stop the appliance?

The appliance starts automatically when you lower the visor. To stop it, raise the visor until it clicks. After use, always set the switch to 'OFF'.

How to clean the removable filter?

To remove the filter, press the tab at the back of the filter and lift it. Clean it regularly. Before each use, make sure it is properly in place and clean.

What to do in case of overheating?

The hairdryer hood is equipped with a safety thermostat. In case of overheating, the appliance switches off automatically. After a few minutes, it will turn back on. Check that the removable filter is clean before reusing.

What safety precautions should be taken in the bathroom?

Never immerse the appliance in water. Do not use near a bathtub, washbasin, or other containers containing water. Unplug it after use. For additional protection, install a residual current device (RCD) with a maximum rating of 30 mA.

How to maintain the appliance?

Use a soft damp cloth with a mild detergent. Make sure the appliance is completely dry before next use. Do not wrap the cord around the appliance.

Can I use the hood on wet hair?

Yes, it is advisable to towel-dry the hair and set it (rollers, simple styling) before placing the hood.

How to direct the airflow?

The professional BaByliss hood features an adjustable system. A button located inside and at the front of the hood allows you to modify the diffuser to direct the air to the top of the head or to the sides according to your hairstyle.

USER MANUAL 889AE BABYLISS

Aluminium upper tube /

Tube supérieur en

aluminium (6)

The BaByliss Super Hood Dryer is protected in its pack and stable once erected, but care should be taken during assembly.

NB:

Never lift the hood by the visor. The position of the hood is fixed to give optimum comfort in use. Do not attempt to adjust the angle.

ASSEMBLY INSTRUCTIONS

The BaByliss Super Hood requires careful assembly before use. Please read the following Assembly instructions carefully:

1. Slide the non-weighted foot into the extended base socket (1) until it clicks home. Insert the 30mm screw (provided) into hole under base and tighten to secure foot. Slide the 3 weighted feet into the remaining base sockets (2), (3), (4).

2. Push the plastic lower tube (5) into the top of the base segment (10) as far as it will go, ensuring that the slot in the lower tube slides over the ridge inside the base segment.

3. Turn the tube connector (7) in a anti-clockwise direction to loosen it and release the upper tube (6). Pull out the upper tube to the desired length. Tighten tube connector to secure.

4. Fix the drying hood onto the top of the aluminium upper tube (6), at position (8) making sure that the hole in the side of the hood socket is aligned with the equivalent hole in the aluminium upper tube. Insert the 12mm screw (provided) into the aligned holes and tighten. NB: for optimum stability, always ensure that the drying hood is positioned directly over the non-weighted foot (1) of the base.
5. Snap the plastic lead bracket (9) onto the aluminium upper tube (6) to hold the lead in position. Then slide the lead under hook located on top of base socket (3) (11).
6. The removable filter must always be in position on the top of the hood before using the dryer.

USEINSTRUCTION

• Adjust the height of the hood to suit your sitting position, via the tube connector, sliding the aluminium upper tube up or down as necessary before re-locking.
• The front visor should be pushed upwards until it clicks

into a holding position.

• Select one of the 3 heat levels using switch located on the side of the hood.

Position III:

For rapid drying or starting the drying process or for thick/long hair

Position II:

For normal drying

Position I:

Cool setting for finishing the style

Start with III or II and end with I

1. Prepare your hair for drying in your usual way e.g. in rollers, lightly towel dried, etc.
2. lift up the visor. Plug in and switch to Position I or II or III.
3. Make yourself comfortable under the hood dryer. Pull down the front visor: this will automatically switch the dryer on.
4. Some styles require a greater airflow on the top of the head, whilst others (e.g. long hair) require the airflow to be directed around the sides. To give this flexibility, the Super Hood Dryer is fitted with an adjustable diffuser. To operate this, there is a slide-switch situated on the inside front edge, underneath the hood.
5. When you want to stop the dryer, simply lift the front visor until it is held in

position.

NB: Always ensure that the dryer is switched to the off position (using the side switch) after each use.

CLEANING

Use only a soft, damp cloth with mild detergent and always ensure that the dryer is fully dry before use.

CAUTION

• Do not immerse in water or other liquids and do not use near basins or other vessels containing water.
• Unplug the hairdryer after use since the proximity of water can be dangerous even if it is switched off. For additional protection the installation of a residual current device (RCD) with a rated residual operating current not exceeding 30mA is advisable in the electrical circuit supplying the bathroom. Ask your installer for advice.
• Store out of children's reach.
  Always unplug the appliance when not in use. Do not leave unattended when switched on.
  Take care to avoid contact between the hot surfaces of the appliance and the face or neck.
  Always ensure the voltage to be used corresponds to the voltage on the unit.
• Do not wrap the supply cord

around the appliance.

• Do not use the appliance if the cord is damaged. In the event of damage discontinue use immediately. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
• Return the appliance to the nearest service facility for examination, electrical or mechanical adjustment or repair. No repair should be attempted by the consumer.
• Allow to cool before storing away.
• Remember to clean the removable filter regularly. To remove the filter, pull the lock at the back of the filter and pull it.
  Always ensure that the dryer is switched to the off position after each use.
  This appliance complies with the requirements of Directives 89/336/E.E.C.(Electromagnetic compatibility) and 73/23/E.E.C. (Safety of domestic appliances), amended by Directive 93/68/E.E.C. (C.E. marking).

minutes but please check removable filter is clean before continuing to use the dryer.

Discarding electrical and electronic equipment at the end of life. In everybody's interest and to participate active

ly in protecting the environment:

• Do not discard these items with your household waste.
• Use the available trade-in and collection systems.

Some materials can in this way be recycled or recovered.

NB:

The BaByliss Super Hood Dryer has a safety cut-out which will operate in case of overheating. The dryer will re-set itself after being left to cool for a few

DEUTSCH

RATSCHLAGE VON BABYLISS