TPL-307E2K - Powerline Adapter TRENDNET - Free user manual and instructions

Product Type	Powerline Adapter (Power Line Communication)
Brand	TRENDNET
Model	TPL-307E2K
Maximum Speed	200 Mbps (HomePlug AV standard)
Network Interface	1 Ethernet 10/100 Base-T port (RJ45)
Power Socket	Integrated, compatible with standard wall sockets
Buttons	Sync (pairing), Reset
LED Indicators	Power, Powerline, Ethernet
Security	AES 128-bit encryption, security button (protected pairing)
Dimensions (approx.)	80 x 60 x 30 mm (per adapter)
Weight (approx.)	100 g (per adapter)
Power Supply	100-240 V AC, 50-60 Hz (via power socket)
Power Consumption	Less than 5 W (typical operation)
Kit Contents	2 Powerline adapters, 2 Ethernet cables (1.5 m), quick installation guide, CD-ROM (utility and manual)
Care and Cleaning	Clean with a dry, soft cloth. Do not use abrasive products or solvents.
Operating Temperature	0 °C to 40 °C
Operating Humidity	10% to 90% (non-condensing)
Certifications	CE, FCC, HomePlug AV
Warranty	3-year limited warranty (per TRENDNET policy)

Frequently Asked Questions - TPL-307E2K TRENDNET

How to install the TPL-307E2K Powerline adapters?

Plug one adapter near your router and connect it via an Ethernet cable to a LAN port on the router. Plug the second adapter in the room where you want to extend the network. Both adapters must be on the same electrical circuit. The Powerline LEDs should light up to indicate an established connection.

What to do if the Powerline LED does not light up?

Check that both adapters are plugged directly into wall sockets (not power strips). Try moving them closer or plugging them into the same circuit. Press the Sync button on each adapter (less than 2 seconds) to pair them. If the problem persists, refer to the troubleshooting guide.

Can I use the Powerline adapters with power strips or surge protectors?

It is not recommended to use power strips or surge protectors as they can filter the Powerline signal and reduce performance. Always plug directly into a wall socket.

Are the TPL-307E2K adapters compatible with other Powerline brands?

Yes, they are compatible with any HomePlug AV certified adapter, regardless of brand. However, for optimal performance, it is recommended to use TRENDNET adapters.

How to secure my Powerline network?

By default, security is provided by AES 128-bit encryption. You can customize the network name (NMK) using the utility on the CD-ROM. Pressing the Sync button on each adapter for more than 10 seconds resets the network.

What is the actual speed of the 200 Mbps adapters?

The theoretical speed is 200 Mbps, but in practice it is lower due to electrical interference and distance. Expect an actual speed around 80 to 100 Mbps, sufficient for HD streaming and online gaming.

Can I connect multiple devices to a single Powerline adapter?

Yes, you can connect an Ethernet switch to the adapter to share the connection with multiple wired devices.

How to reset a Powerline adapter?

Insert a paperclip or pointed object into the Reset hole and hold for 10 seconds. Factory settings will be restored.

Do Powerline adapters work with a smart electricity meter?

Yes, they generally work, but some meters may attenuate the signal. If speed is low, try plugging the adapters before the meter (if accessible) or use a Powerline filter.

Where to find the full user manual?

The full manual is on the CD-ROM included in the package. You can also download it from the TRENDNET website in the support section.

USER MANUAL TPL-307E2K TRENDNET

1. Go into the Control Panel, click Network and Internet, click Network and Sharing Center, click Change Adapter Settings and then right-click the Local Area Connection icon and then click Properties.

Local Area Connection

Identify NtDIA m

Disable

Status

Diagnose

Bridge Connections

Create Shortcut

Delete

Rename

Properties

Obtain an IP address automatically

Use the following IP address:

P address:

Submel mask

Default gateway:

192.168 10.5

255.255.255.0

AD = AC = 1

1. Click Internet Protocol Version 4(TCP/IPv4) and then click Properties. Then click on Use the following IP address, and make sure you assign your network adapter an IP address in the subnet of 192.168.10.x.

Windows Vista

1. Go into the Control Panel, click Network and Internet, click Network and Sharing Center, click Manage Network Connections and then right-click the Local Area Connection icon and then click Properties.

Local Area Connection

Identity

N/AIDAA

Disable

Status

Diagnose

Bridge Connections

Create Shortcut

Delete

Rename

Properties

Obtain an IP address automatically

Use the following IP address:

IP address:

Subnet mask:

Default gateway:

192168105

255.255.255.0

m - 1 ≠ 0 ;

1. Click Internet Protocol Version 4(TCP/IPv4) and then click Properties. Then click on Use the following IP address, and make sure you assign your network adapter an IP address in the subnet of 192.168.10.x.

Windows XP/2000

1. Go into the Control Panel, double-click the Network Connections icon and then right-click the Local Area Connection icon and then click Properties.

Cone

Disable

Status

Repair

Bridge Connections

Create Shortcut

Delete

Rename

Properties

Obtain an IP address automatically

Use the following IP addresses:

P address:

Subnet mask

Default gateway:

192.168 10.5

255.255.255

m - 1 ≠ 0 ;

1. Click Internet Protocol (TCP/IP) and then click Properties. Then click on Obtain an IP address automatically. Then click on Use the following IP address, and make sure you assign your network adapter an IP address in the subnet of 192.168.10.x.

2. I have verified that my Powerline device is connected to my workstation, but I cannot detect other Powerline devices. What should I do?

1. Verify that you are using Cat. 5, Cat 5e or Cat. 6 Ethernet network cables from each TPL-310AP adapter.
2. Verify that the power outlet of the TPL-310AP is plugged into is on the same electrical power distribution and/or circuit breaker box.
3. If you are still not able to establish connectivity after performing the above steps, please reset the TPL-310AP other powerline devices to factory default. The default network name/key is "HomePlugAV". The Reset button is located on the bottom of the TPL-310AP.

a: With a pin or paperclip, press and hold the reset button for 1 second and release it. The PWR and PL LEDs will turn off and turn back on. (Note: The PL LED will flash in amber.)
b: To verify connectivity, the PL LED will become solid when the powerline adapters establish connectivity. The TPL-310AP and your other powerline devices must have the same network name/ key in order to connect to each other.

Note: If you have problems resetting the device, unplug the powerline access point(s) from the power outlet, wait 15 seconds and plug the access point(s) back into the outlet, then repeat the reset procedure.

3. I can detect my Powerline devices on my Powerline network, but I cannot connect to the Internet. What should I do?

Assuming that the Powerline network is connected to a router:

1. Make sure you are not connecting the device into a surge protector or power strip.
2. Make sure that your Router is connected to the Internet and one of the Router's LAN port is connected to a TPL-310AP or other powerline device. Check both the powerline device and the router's network port LED for positive connection status.
3. Make sure the TCP/IP setting for your computer's network adapter is set to Obtain an IP address automatically (see the steps below).

Windows 7

1. Go into the Control Panel, click Network and Internet, click Network and Sharing Center, click Change Adapter Settings and then right-click the Local Area Connection icon and then click Properties.

Local Area Connection

Identify in NVIDIA et al.

Disable

Status

Diagnose

Bridge Connections

Create Shortcut

Delete

Reame

Properties

blan an IP address automatically

Use the following IP address:

IP address:

Sybnet mask:

Default gateway

1. Click Internet Protocol Version 4(TCP/IPv4) and then click Properties. Then click on Obtain an IP address automatically.

Windows Vista

1. Go into the Control Panel, click Network and Internet, click Network and Sharing Center, click Manage Network Connections and then right-click the Local Area Connection icon and then click Properties.

Local Area Connection

Identity

Disable

Status

Diagnose

Bridge Connections

Create Shortcut

Delete

Recycle

Properties

Obtain an IP address automatically

Use the following IP address:

IP address:

Subnet mask:

Default gateway

1. Click Internet Protocol Version 4(TCP/IPv4) and then click Properties. Then click on Obtain an IP address automatically.

Windows XP/2000

1. Go into the Control Panel, double-click the Network Connections icon and then right-click the Local Area Connection icon and then click Properties.

1

local

Conne Status

Repair

Bridge Connections

Create Shortcut

Delete

Rename

Properties

Obtain an IP address automatic

Use the following IP address:

IP address:

Sybnet mask:

Default gateway:

1

1. Click Internet Protocol (TCP/IP) and then click Properties. Then click on Obtain an IP address automatically.

2. I have a HomePlug 1.0 or HomePlug Turbo network. Can I use this with my network?

The TPL-310AP is not backwards compatible with HomePlug 1.0 or HomePlug Turbo.

1. I typed http://192.168.10.100 in my Internet Browser's Address Bar, but an error message says "The page cannot be displayed." How can I get into the TPL-310AP web configuration page?

2. Check your hardware settings again by following the instructions in section 2.

3. Make sure the ETH and WIFI lights are lit.
4. Make sure the TCP/IP settings are configured properly (see question 1).
5. Since the Access Point's default IP address is 192.168.10.100, make sure that no other network devices are assigned an IP address of 192.168.10.100.

6. Reset the Access Point. Take a pin or paperclip and press the RESET button for 5 seconds, then let go. Then type http://192.168.10.100 into your browser.

7. If my network's IP is different than the Access Point's range, what should I do?

You should still configure the Access Point first. In Step 9 in section 2: Configure the Access Point, select Disabled for DHCP and change the IP address of the Access Point to match your network's IP (e.g. 192.168.2.x, 192.168.0.x).

7. After I successfully configured the Access Point to meet my network settings, I cannot connect to my network using wireless computers.

If you have a DHCP server in your network, you need to go into TCP/IP settings again and re-select "Obtain an IP address automatically" to allow the PC to regain an IP address from your DHCP server.

8. All the settings are correct, but I cannot make a wireless connection to the Access Point.

1. Double check that the WIFI light on the Access Point is lit.
2. Power cycle the TPL-310AP. Move the power switch to the off position. Wait 15 seconds, and then move the switch to the on position.
3. Contact the manufacturer of your wireless network adapter. Make sure the wireless network adapter is configured with the proper SSID. The default SSID of the Access Point is TRENDnet310. If you have enabled encryption on the Access Point, make sure to configure the wireless network adapter with the same encryption key.

If you still encounter problems or have any questions regarding the TPL-310AP, please refer to the User's Guide included on the Utility CD-ROM or contact TRENDnet's Technical Support Department.

The following are some general wireless tips to help minimize the impact of interference within an environment.

Assign your network a unique SSID

Do not use anything that would be identifying like "Smith Family Network". Choose something that you would easily identify when searching for available wireless networks.

Do not turn off the SSID broadcast

The SSID broadcast is intended to be on and turning it off can cause connectivity issues. The preferred method of securing a wireless network is to choose a strong form of encryption with a strong and varied encryption key.

Note: after setting up the SSID, encryption type and encryption key/passphrase, please make a note of them for future reference. You will need this information to connect your wireless computers to the wireless router/access point.

Change the channel

Most wireless access points and routers are defaulted to channel 6. If you have a site survey tool that will display the channels you can plan your channel selection around neighboring access points to minimize interference from them. If your site survey tool does not display the channel try using channels 1 or 11.

If you are using 802.11n you should be securing the network with WPA2 security.

Note: Due to Wi-Fi certification considerations if you choose WEP, WPA or WPA2-TKIP encryption this device may operate in legacy wireless mode (802.11b/g). You may not get 802.11n performance as these forms of encryption are not supported by the 802.11n specification.

Please also make sure that the wireless hardware is not placed in any type of shelving or enclosures.

Avoid stacking hardware on top of each other to prevent overheating issues

Maintain enough free space around the hardware for good ventilation and airflow. There should also be plenty of free space around the antennas to allow the wireless signal to propagate.

There are a number of other environmental factors that can impact the range of wireless devices.

1. Adjust your wireless devices so that the signal is traveling in a straight path, rather than at an angle. The more material the signal has to pass through the more signal you will lose.

2. Keep the number of obstructions to a minimum. Each obstruction can reduce the range of a wireless device. Position the wireless devices in a manner that will minimize the amount of obstructions between them.

3. Building materials can have a large impact on your wireless signal. In an indoor environment, try to position the wireless devices so that the signal passes through less dense material such as dry wall. Dense materials like metal, solid wood, glass or even furniture may block or degrade the signal.

4. Antenna orientation can also have a large impact on your wireless signal. Use the wireless adapter's site survey tool to determine the best antenna orientation for your wireless devices.
5. Interference from devices that produce RF (radio frequency) noise can also impact your signal. Position your wireless devices away from anything that generates RF noise, such as microwaves, HAM radios, Walkie-Talkies and baby monitors.
6. Any device operating on the 2.4GHz frequency will cause interference. Devices such as 2.4GHz cordless phones or other wireless remotes operating on the 2.4GHz frequency can potentially drop the wireless signal. Although the phone may not be in use, the base can still transmit wireless signals. Move the phone's base station as far away as possible from your wireless devices.

If you are still experiencing low or no signal consider repositioning the wireless devices or installing additional access points. The use of higher gain antennas may also provide the necessary coverage depending on the environment.

Detalls standard applicable:

EN300328

V1.7.1: 10-2006

EN 55022:2006+A1:2007

EN 301 489-1

V1.8.1:04-2008

EN 61000-3-2 : 2006

EN 301 489-17

V2.1.1:05-2009

EN 61000-3-3 :2008

EN 50412-2-1 : 2005

EN 60950-1:2006 +A11:2009

Déclaration:

Director of Technology

Position / Title

Signature

Certifications

This equipment has been tested and found to comply with FCC and CE Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.
(2) This device must accept any interference received. Including interference that may cause undesired operation.

Waste electrical and electronic products must not be disposed of with household waste. Please recycle where facilities exist. Check with you Local Authority or Retailer for recycling advice.

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.

ADVERTENCIA

Description of Modes

Erp (EuP) Operation: Standby Mode

The EUT has no external mechanical switch and uses an internal program to control active and standby modes.

Disconnect the Ethernet cables from the device Ethernet ports, and after 3 minutes, the device will enter standby mode. The Power (PWR) LED will flash every 15 seconds to indicate that the device is currently in standby mode. To return to active mode, reconnect the Ethernet cables to the device Ethernet ports, and the device will re-enter active mode.

Product Warranty Registration

Please take a moment to register your product online. Go to TRENDnet's website at http://www.trendnet.com/register