CAPTURECUT PRO XF8705 - Hair clippers REMINGTON - Free user manual and instructions

Product type	Rechargeable shaver/trimmer, usable in the shower
Brand	Remington
Model	CaptureCut Pro XF8705
Power supply	100-240V AC adapter, output 5V DC 1A, charges via stand
Battery life	Quick charge 5 min for 1 shave (3 min), full charge 24 h
Shaver head	Interchangeable foil and blades, model SPF-XF05
Integrated trimmer	Intercept pop-up trimmer for detailing
Charge indicator	LED display with battery level and remaining minutes
Water usage	Can be used in the shower, rinse under running water
Cleaning	Rinse head with warm water after each use, do not use brush on foil
Blade maintenance	Lubricate trimmer teeth every 6 months with sewing machine oil
Replacement parts	Replace foils and blades every 6 months, replacement head SPF-XF05 available
Safety	Adapter must not be wet, do not immerse stand, use only original accessories
Operating temperature	Between 10°C and 35°C
Repairability	Removable battery for disposal, disassembly possible with screwdriver
Target audience	Adults, use by children >8 years under supervision
Warranty	See manual for warranty terms

Frequently Asked Questions - CAPTURECUT PRO XF8705 REMINGTON

How long does the initial charge take?

For first use, charge the device for at least 24 hours for optimal performance.

Can I use the shaver in the shower?

Yes, the shaver is designed for shower use. You can rinse it under running water after use.

How do I clean the shaver head?

Remove the foil by pressing the release buttons, shake off debris, then rinse the foil under running water. Do not use a brush on the foil.

What if the shaver does not turn on?

If the battery is empty or the device has not been used for a long time, a 5-minute quick charge is enough for a 3-minute shave. Make sure the device is off before charging.

When to replace foils and blades?

Replace foils and blades every 6 months to maintain optimal performance. Use replacement model SPF-XF05.

How do I lubricate the trimmer?

Every six months, apply a drop of sewing machine oil to the teeth of the pop-up trimmer.

Can I use the shaver with the cord?

No, the shaver runs only on battery. Quick charge (5 min) gives enough power for one shave.

How do I know if the battery is low?

On the XF8705 model, the LED display shows flashing 'Lo' when the battery is low. While charging, the indicators rotate clockwise.

Can children use this shaver?

Children over 8 years old can use it under adult supervision after receiving proper instructions.

How to dispose of the shaver at end of life?

Do not dispose of the device with household waste. Remove the battery (follow disassembly instructions) and recycle it separately. The device must be taken to an electronic waste collection point.

USER MANUAL CAPTURECUT PRO XF8705 REMINGTON

CaptureCut Foil Shaver

XF8505

XF8705

Thank you for buying your new Remington product. Please read these instructions carefully and keep them safe. Remove all packaging before use.

IMPORTANT SAFETY INSTRUCTIONS

WARNING - TO REDUCE THE RISK OF BURNS, ELECTROCUTION, FIRE OR INJURY TO PERSONS:

1 This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been supervised/instructed and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be done by children unless they are older than 8 and supervised. Keep the appliance and cable out of reach of children under 8 years.
2 The adaptor contains a transformer. Do not cut off the adaptor to replace it with another plug, as this causes a hazardous situation.
3 Make sure the adaptor does not get wet.
4 Suitable for cleaning under an open water tap.
5 Always unplug the appliance before you clean it.
6 Suitable for use in a bath or shower.
7 Do not immerse the charging stand in water or any other liquid, nor rinse it under the tap.
8 Do not plug or unplug the appliance with wet hands.
9 Do not use the shaver, adaptor, charging stand or any other part if it is damaged, as this may cause injury. Always replace a damaged adaptor or charging stand with one of the original type.
10 Use, charge and store the appliance at a temperature between 10^ and 35^ .
11 Only use the adaptor, charging stand and accessories supplied.
12 Always put the protection cap on the product to protect the cutting heads when you are travelling.
13 Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by Remington.
14 This appliance is not intended for commercial or salon use.
15 DThis appliance should be charged by approved safety isolating adaptors PA-0510E(K) with the output capacity of 5.0Vdc; 1.0A.

KEY FEATURES

1 On/off switch
2 Intercept trimmer
3 Shaving foils
4 Hair pocket
5 3 stage charge indicator (XF8505)
6 LED display (XF8705)
7 Charging pins (on back)

8 Pop-up trimmer (on back)
9 Head guard (not shown)
10 Foil assembly release buttons
11 Charging stand (not shown)
12 Adaptor (not shown)
13 Storage pouch (not shown)

GETTING STARTED

It is recommended that you use your new shaver daily for up to four weeks to allow time for your beard and skin to become accustomed to the new shaving system.

CHARGING YOUR SHAVER

• Ensure the product is switched off.
• Connect the charging stand to the adaptor and then to the mains.
• Place the charge stand on a flat surface.
• Place the shaver in the charge stand with the charge pins contacting.
  Charge for at least 24 hours when using for the first time.
  XF8505: At low charge the LED indicator will flash rapidly. When charging the LED will flash slowly.
• When fully charged the LED will light solid for 1 minute and then turn off.
  XF8705: When charge is low 'Lo' will flash rapidly on the screen. When charging, the LED's flash in a clockwise rotation.
• When fully charged the minutes will flash 60 for 1 minute and then turn off.
• To preserve the life of your batteries, let them run out every 6 months then recharge for 24 hours.
• The appliance adapts automatically to a mains voltage between 100V and 240V.
• Quick charge feature: Your shaver is fitted with a 5 minute quick charge feature that will provide enough charge for 1 shave (3 minutes).

INSTRUCTIONS FOR USE

SHAVING

Make sure your shaver is properly charged.
- Switch the shaver on by pressing the on/off switch.
- Stretch the skin with your free hand so the hairs stand upright.
Hold the shaving head so that the foils touch your face.
Use short, linear strokes.

TRIMMING

• Switch the shaver on.

• Push the trimmer release button up to activate the trimmer.
  Hold the trimmer at a right angle to your skin.

• To retract the trimmer, slide the trimmer release button down and push the back of the trimmer head downwards until it locks into place.

TIPS FOR BEST RESULTS

Always hold the shaver at right angles to the skin so that all foils are touching the skin with equal pressure.
- Use moderate to slow stroking movements. The use of short circular motions in stubborn areas may obtain a closer shave, especially along the neck and chin line.
- DO NOT press hard against the skin in order to avoid damage to the foil heads.

Note: your shaver has been designed to be used in the shower if desired.

Care for your appliance to ensure a long lasting performance.
We recommend you clean your product after each use.
- The easiest and most hygienic way to clean the appliance is by rinsing the appliance head after use with warm water.
- Keep the switch in the "off" position when not in use.

CLEANING CAUTIONS

• Remove the foil assembly by pressing the release buttons on either side of the head and lifting the foil assembly upwards to remove from the hair pocket.
• Tap out the excess hair shavings and rinse the foils under running water.
• Do not clean the shaving foil with a brush.
• Replace the head assembly by placing the assembly on top of the hair pocket, press down and click into place.

\* CLEANING TRIMMER

• Lubricate the teeth of the trimmer every six months with a drop of sewing machine oil.

REPLACING THE FOILS & CUTTERS

• To ensure continued high quality performance from your shaver, we recommend the foils and cutters are replaced every six months.

Signs that your foils and cutters need replacing.

• Irritation: as foils get worn, you may experience skin irritation.

Pulling: as the cutters wear, your shave may not feel as close and you may feel the cutter pulling your hair.
- Wear through: you may notice that the cutters have worn through the foils.

TO REPLACE THE FOIL

• Remove the foil assembly by pressing the foil assembly release buttons on either side of the head and lifting the assembly upwards to remove from the hair pocket.
• Insert the new foil assembly on the hair pocket, press down and click into place.

REPLACING THE CUTTERS

• Grasp the cutter between your thumb and forefinger and pull upwards.
  Snap the new cutter into the oscillator tip.
  Note: DO NOT press on the cutter ends as this may cause damage.
• Foil head replacements can be found on the Remington website. Spare part number SPF-XF05

TROUBLESHOOTING

• If your shaver battery is completely empty or the shaver has not been used for an extended period of time, the shaver may not start when operated using the cord. If this occurs, a 5 minute quick charge will allow for 3 minutes of shaving.

BATTERY REMOVAL

The battery must be removed from the appliance before it is scrapped.
- The appliance must be disconnected from the supply mains when removing the battery.
- Slide the trimmer up to the open position and remove a single philips head screw.
Using a small flat screwdriver pry the back cover off the shaver.
- Using a philips screwdriver remove 8 screws to open the back of the internal housing.
- Remove and open the core from the shaver to expose the batteries.
- Cut the wire connecting the batteries to the circuit board and remove the batteries.
The battery is to be disposed of safely.

ENVIRONMENTAL PROTECTION

To avoid environmental and health problems due to hazardous substances in electrical and electronic goods, appliances marked with this symbol must not be disposed of with unsorted municipal waste, but recovered, reused or recycled.

UW APPARAAT VERZORGEN

REEMPLACEMENT DES LAMES

RADY, JAK OSIAGNAC NAJLEPSZY WYNIK

Ecn6aTapeB6pntbI pONHOCTbO pa3pRjEHa IIN6pNTBOB B TeUHe nIeNtBnHO BPemEH He NOp3bOaBnC, ee HEnb3B KBNoAub npn ONDKLIIOHcHOB M CbET bHype. B 3TOM cUYae 6bICTpa 3apJdA B TeUHe N5MHyT PNO3BOINIT 6pNTbC4 3 MNHyTbI.

I3BLeueHNE BATAPEI

• Ipepeytnn3aunne6aTaapeu cneyu TnBLeuy n3 yCtpoiCTBa.
  -ПииИЗВLEЧЕНСБаТApEиУСТРОДСТВОСLEДуETOTKЛЮЧИТБOTЭЛКТРОСЕТИ.
  IpeeBnHbTe TpMMep B OTKpbToe NOJIOKeHne N CHMNTe OINH C NOMObIo OTBepTKN C KpeTo06pa3HbIM IJIncem.
  C nOMOuMaJIeHbKo OTBepTKn NOIeHbTe 3aHIOU qAcTb KOpnyca.
  MaIenbKOJOTBepTKOICKpeTOO6pa3HbIMUINcEmOTKpyTnTe8BHTOB, TTo6blOTKpbTb3aHIOuCACTbBHyTpeneHeroKOpnyca.
• ɪЗвileкпгіеɪз 6рntbblɪ packpoitte 6aTapeHbɪŋ OTeK,чTo6bl nOlyuHTbdoCTyn K 6aTapeqM.
• 06pejxbTe npoBda, coeHHaUOJIne 6aTapeu c MoHTaxHoN pIaToH, n 3BVeKeNTe 6aTapeu.
• Baatarpe noIopIeKHT 6e3oNacHoi yTuJIn3aCNI.

3KoIornuecka 3aunTa

Bo n36eJahne npOBeM c 3KoIogNei n 3OpOBbEm, Bbl3BaHHbIX BvIeCTBaMn, COdEpaJauIMNcB BJIeKTPnueCCKNX I3eKTPoHHbIX yCTpoIcTBa, YCTPOINCTBa, NOMEeHHbIe 3TmN CmBONOM, CJIeDyET yTNII3NPOBaTb OTJeBH0 NT HecOpTnIOBAHbIX 6bITOBX bTOXIOB; OHNI pNDJIeKAT BOcCTaHOBJLHeHIO, NOBTOPHOMY IcNoIb3OBAHIO IJI nepepa60Ke.

EN IYI SONUCLARICIN IPUCLARI

SPF-XF05:4aLlRJrJrJrJrJrJrJrJrJrJr

JSLWJL

aal aai 5 5 5

3

C. | x - 2| = | x + 3|

Aio wlll l jjlln no yjlllgl

laia aill jia jia jia jai jai jai

aalal alal alal alal alal alal alal

jia 1

glll lll glll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll

aalalal alalal aalal alal

cJyjlll j 1000000000000000000000000000000000000000

J

auiui

aayyagll algal g aalall algal aalall ayaaal yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall yaiall

g jai jia jie juaa

aallll lllllllllllllllllllllllllllllllllllll

Ljulua Ubaia 1

gblall g 1s

a dall a 10000000000000000000000000000000000000000000

ailllll llll llll llll llll

aBaal aIaIa IaIa

aill 15 15 15 15 15 15 15

a

aLusuul uus y Lueie "off" uus uus cuaal Jauai

aaii iiaaii iiaii

j 1

Jla cia jil jil jil jil jil jil jil

Ail

a a a a a a a a a a a a a a a a a a a a

aill

J

e 1

1

AilSgaiinjBiai jbiBai, jaiill gie iiall qai jai

a

aalall aal alal

y

8

（） 9

S OBC = S COD + S BDO - S BOC

( 1 + u) + ·s + ( 1 + z) + ( 1 + 1) > 1 + z + 1 = 3 1 + z + 1 = 2z

(1) ( x,y) ( x,y - 1)

( A,B,E) ( D,E) 以 A 为直径的圆上

Jaeill 8

aaiy i aai j Jaaiaa aaii aaii aaii aaii aaii aai

aill llll 1ie 2eill 3i, 4ii

A

julil

a 1

jua 1

aaii iiai iiai iiaii aie

oJyJy plznnn 1ie Jgle acl24 odJn

a:XF8500

.

aaiy

Remington® is a Registered Trade Mark of Spectrum Brands, Inc.,

or one of its subsidiaries

VARTA Consumer Batteries GmbH & Co. KGaA, Alfred-Krupp-Str. 9, 73479 Ellwangen,

Germany

www.remington-europe.com

© 2016 Spectrum Brands, Inc.