ODYSSEY - Mobile Phone TRIUM - Free user manual and instructions

USER MANUAL ODYSSEY TRIUM

PCR Trium by MITSUBISHI ELECTRIC This guide describes the operation of the Trium dual band GSM/GPRS telephones Aura - Mystral - Odyssey Edition 1, 2002. © Mitsubishi Electric Telecom Europe, 2002 Whilst every effort has been made to ensure the accuracy of the instructions contained in this guide, Mitsubishi Electric reserves the right to make improvements and changes to the product described in this guide and/or to the guide itself, without prior notice.

SAR THIS AURA, MYSTRAL OR ODYSSEY PHONE MEETS THE EU REQUIREMENTS FOR EXPO- SURE TO RADIO WAVES. Before a phone model is available for sale to the public, compliance with the European R&TTE directive (1999/5/CE) must be shown. This directive includes as one essential re- quirement the protection of the health and the safety for the user and any other person. Your mobile phone is a radio transmitter and receiver. It is designed and manufactured not to exceed the limits for exposure to radiofrequency (RF) energy recommended by The Council of the European Union! . These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines were developed by independent scientific organisations through periodic and thorough eval- uation of scientific studies. The limits include a substantial safety margin designed to as- sure the safety of all persons, regardless of age and health. The exposure standard for mobile phones (CENELEC standard EN 50360: 2000) employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit? rec- ommended by The Council of the European Union is 2.0 W/kg. Tests for SAR have been conducted using standard operating positions (with reference to CENELEC standard EN 50361: 2000) with the phone transmitting at its highest certified power level in all tested frequency bands?. Although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value. This is because the phone is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a base station antenna, the lower the power output. The highest SAR value for this Trium Aura, Mystral or Odyssey model when tested for compliance against the standard was 1.120 W/kg. While there may be differences be- tween the SAR levels of various phones and at various positions, they all meet the EU re- quirements for RF exposure. There are a number of independent sources of information available to users including: Royal Society of Canada: www.rsc.ca The International Commission on Non-lonizing Radiation Protection (ICNIRP): www.icnirp.de The US Food and Drug Administration: www.fda.gov/cdrh/ocd/mobilphone.html The World Health Organization: www.who.intlemf Mitsubishi Electric belongs to the MMF, an international association of radio equipment manufacturers. The MMF produces information such as this in accordance with its purpose of developing and presenting industry positions to independent research organisations, government and other research bodies Mobile Manufacturers Forum mant Building, 80 Blvd. A. Reyers B-1030 Brussels Belgium www.mmfai.org

1. European recommendation 1999/519/CE

2. The SAR limit for mobile phones used by the public is 2.0 watts/kilogram (W/Kg) aver-

aged over ten grams of tissue. The limit incorporates a substantial margin of safety to give additional protection for the public and to account for any variations in measure- ments

3. The maximum level of GSM emitted power is 250mW at 900 MHz and 125 mW at 1800

MHz according to the GSM standard

See next page ALPHANUMERIC KEYS © -@, æ. ®. Press to enter numbers, characters and punctuation CHANGEABLE FRONT COVER (except Mystral) See page 59 @, hold down to call voice mail @ to ®), hold down for speed dialling CHANGEABLE BATTERY COVER (at the back of the À phone) See page 12 @, hold down to enter + prefix, P' (pause) or" (wildcard) @, hold down to lock Keypad. To unlock, press Unlock /=\ then @ MICROPHONE

HEADSET, ACCESSORIES AND

AC/DC CHARGER SOCKET

Using the keys to follow the actions described in this guide To help you quickly understand your way around this manual we have used sym- bols and expressions that are present on the keys and in the display. /\ LEFT SOFTKEY. The function of the softkey appears in the graphic display above the key. CALL/SEND key. Press to make/answer a call. In stand-by, press to display the last dialled numbers you dialled. Li} RIGHT SOFTKEY.

(S) — (3) END key. Hold down to turn the phone on/off. Press to end à call or return to stand-by. A UP ARROW on the cursor key. Press to scroll up menus {while in the menu). In stand-by, press to access the volume control. DOWN ARROW on the cursor key. Press to scroll down men- 7 us (while in the menu). In stand-by, press to access the alert mode (ring, silent, vibrate, etc.) | » RIGHT ARROW on the cursor key. Press to access the main NX menu or select a menu option. 4 LEFT ARROW on the round cursor key. Press to access the phone book or return to the previous display Function / Softkey with the corresponding function name For example, Internet /=\ means press the softkey under the word Internet. Messages Words in this format are the words in the display. Select means use À and w on the cursor key to scroll to the re- quired item in the menu and validate by pressing p. For ex- ample, “select Phone Book" means scroll to the menu item Phone Book and validate by pressing p. Press means press the corresponding key. Press 1 means press the SEND key. Graphic display The display shows icons, alphabet characters, numbers, menu list and instructions to the user. Use the above keys Operator +0 navigate to the phone book, Internet/WAP"* and the menu. The rest of this guide gives the procedures to ac- ess these functions. Icons in the display are described on page 5.

Understanding the icons icons in the display have the following meaning: Lil

SIM memory in use Phone memory in use. When you enter a name and address you can choose the icon you want to go with it. Roaming. Displayed when the phone is logged on to a network dif- ferent from its home network. Short message service (SMS). Displayed when you have one or more messages to read. It flashes # when the SMS message bank is full and cannot store new messages. Delete one or more old messages to make space. The availability of this feature is network dependent Voice mail. Displayed when you have a voice mail message to read The availability of this feature is network dependent. Call diverting. Indicates whether incoming calls are permanently being diverted. The availability of this feature is network dependent. Battery level indicator. Permanently displayed to indicate the cur- rent charge level of the battery. Three levels are shown. mr low, mt medium, mt full. It flashes mm when the battery is almost empty. Arrow keys. Displayed during menu operation to indicate that more items in the menu can be displayed if à or w are pressed. Line 2. Indicates the second line is in use. The availability of this feature is network dependent. Unanswered call. Displayed when an incoming call is unanswered. Signal strength level. It indicates the strength of the received sig- nal. The more bars the stronger the signal. If no network is available the display remains blank. Keypad lock. Indicates whether keypad lock is on or off. Alarm clock icon Vibrator alert icon. Ring tone off. All tones are off. Mute icon Tegic edit mode icon WAP" ‘live’ connection icon. WAP" ‘live’ connection in security mode icon. GPRS attached in idle mode icon WAP" GPRS connection icon. WAP" GPRS connection in security mode icon. Auto-switch function activated icon.

Introduction Thank you for purchasing the Trium Aura, Mystral or Odyssey dual band mobile tel ephone. The mobile telephone described in this guide is approved for use on all GSM 900/1800 and GPRS networks. Services and display messages may be differ- ent. This depends on your operator's implementation. As with all types of radio transceivers this mobile telephone emits electromagnetic waves and conforms to international regulations when it is used under normal con- ditions and in accordance with the safety and warning messages given below and on page 13. General safety fs important to follow any special regulations regarding the use of radio equip- ment, due to the possibility of radio frequency, RF, interference. Please follow the safety advice given below. More safety information is described on page 13. Switch off phone and remove the battery when in an aircraft. The use of mobile telephones in an aircraft may endanger the operation of the aircraft, disrupt the cellular mobile phone network and is illegal. Failure to observe this instruction may lead to suspension or denial of mobile telephone services to the offender, or legal action, or both Respect national regulations on the use of mobile telephones in vehicles. Do not use a handheld phone while driving. If you don't have a hands free car kit, stop and park your vehicle safely before using your phone. Switch off phone when at any refuelling point or near inflammable material. Switch off phone in hospitals and any other place where medical equipment may be in use. Respect restrictions on the use of radio equipment in fuel depots, chemical plants or where blasting operations are in progress. There may be a hazard associated with the operation of phones close to inadequately protected personal medical devices such as hearing aids and pacemakers. Consul your doctor or the manufacturers of the medical device to determine if it is adequately protected. Operation of phone close to other electronic equipment may also cause interference if the equipment is inadequately protected. Observe any warning signs and manufacturers recommendations. Avoid prolonged contact between the antenna and your skin when the phone is switched on. This apparatus is intended for use only when supplied with power from AC/DC adaptor chargers (FZ14130070, FZ14130060, FZ14130050, FZ14130080, FZ14130090 or FZ14130100) and the vehicle kit (FZ14180040). Use of any other charger or adaptor will invalidate any approval given to this appa- ratus and may be dangerous.

Preparing to make your first call. Making your first call Battery … .

Vehicle safety. . Emergency calls… Care and maintenance . AC/DC adaptor chargers.. 14 Battery use. Your responsibility... 15 Security codes . Disposing of waste packaging

3. Using your phone.

Standby display… Important icons. Dialling from memory Last dialled numbers . Speed dialling …… Silent and vibrate alert modes Hands free features 18 Muting … 18 Volume adjustment 19 Sending DTMF tones . Pause feature . Holding and retrieving a call. Call waiting, swapping and multi-party conference calls.…….… 20

Getting started In order to become familiar with the phone quickly, follow these simple steps. Preparing to make your first call Inserting the SIM card Unpack the phone and insert the SIM card into the holder, as shown be- low, with the gold contacts facing down. Fitting the battery Connect the battery as shown below. Placing the battery cover Place the battery cover as shown below.

Making your first call [1 lfthere is not enough charge in the battery to power the phone follow the instructions for battery dhrging on page 11 Turning on the phone © Press and hold down (9) for two seconds. If this is the first time you have used the phone or you removed and replaced the bat- tery, the phone prompts you for the date and time. If you inserted the SIM card incorrectly, the error message Check SIM! appears. Remove the cover and battery and make sure the SIM is inserted with the gold contacts facing down. If the mobile is locked, Code: appears. Enter the 4 digit phonelock code and press OK /-\, The default is 4 zeros, e.g. 0000. If your SIM is PIN protected, Enter PIN: appears. Enter the PIN code and press OK /-\. An animated screen icon appears, then the stand-by display. EP See page 4 to change jour PIN and ct codes! Stand-by display From the stand-by display: Press. to... pb |enterphone menu. Operator directly access to numbers stored 2230 A in phone books. LL 0 Mon. 08 2 access volume control. Internet SMS 52 access alert tones. U access the last dialled numbers list. © [stop the dialling or end a call. D. @[enternumbers in the display Bee DS | aiso "Speed dialling', page 18). See page 44 to set the time and date. Making a call The phone can only make and receive calls when it is switched on, un- locked (see page 16), has a valid SIM card inserted and has GSM/GPRS* network service coverage. If the phone cannot find a valid network the dis- play remains blank © Enter the desired telephone number using the numeric keys (© = ©). You can enter a maximum of 46 digits. Correct any mistakes by pressing Clear/\. Hold down this key or press (]to clear the whole display. @ To dial (send) the number press +. The allait of GPRS depends on jour mobil phone model and on jour ubscipion Getting started

The phone rings and the call connects like a normal telephone. A call timer appears. [1 You cn prefiintermational clls mith 00 or + . To enter the + symbol before à number press and bol doun You can also get the following messages if the call does not connect or you use the second line: Your phone FFhe.. displays. Busy called party is engaged. Not allowed | number dialled is not authorised by the FDN list (see fixed dialling) | page 28). = callis made using the second line (see page 36). Ifthe dialled number matches one stored in the phone book then the name of the called person appears in the display. Receiving a call The phone rings (or vibrates, see page 37 to set) when it receives a call. See page 38 to set the incoming ring tone. See page 39 to set the backlight. Answering the call Press \L). 91 1fthe ring tone volume is se to zer [off orfthe phone has been set Vibrte' mode, no audi ble sound is heard. No ring Pressing No ring /-\ stops the sound of the ring tone, which allows you to, for example, go out of a room before pressing {L Service number presentation If you have the service number presentation your phone displays the fol- lowing information. Your phone displays.… the numbers. Unknown number, then Call1 | unavailable. when connected the caller's number available but not in phone books. Withheld number, then Calll | withheld. when connected If you have a second Îîne, m3 appears if the call has been received on your line 2 number (see page 20 for details). Rejecting the call To reject, or return a busy signal to the caller: Press (5). Ending a call Press (5). The call timer stops and gÿ disappears.

[4 Waïting à feu seconds or pressing the Ed sofleyrtums the phone to the tand-b dsl. The phone stores the callers number, it available, In the received calls log (see page 33). Turning off the phone Press and hold down (5). The mobile turns off. Battery Low battery warning When the battery power falls to its lowest level the message Low Battery! appears and a low battery warning tone sounds. If you are on a call, terminate the call and turn off the phone by pressing and holding down (3 Recharge the battery as shown below or swap it for a charged one. Do not turn off the phone by removing the battery, data can be lost. Charging the battery To ensure a long life for your battery, re-charge it only when the Low Bat- tery! warning appears and the ‘low battery tone is heard Connect the charger to the phone as shown. A Getting started While inserting the plug in the phone AC/DC connector make sure the Trium logo (=) appears on top. Plug the charger into the wall socket and turn on the mains. The battery Start to charge. The phone can be used while charging but this increases the charging time. Charging indicators when the mobile is off During charging Charging... appears. When charging is finished, Battery full appears. It is normal for the battery to get warm during charging. Charging indicators when the mobile is on During charging the mr icon flashes 1-2-3 bars continuously. When charg- ing completes the battery indicator shows three solid bars.

Disconnecting the charger Atthe end of charging, disconnect the charger from the phone (see be- low), switch off and remove the plug from the mains.

Typical charging times using the AC/DC adaptors (FZ14130070, F214130060, FZ14130050, FZ14130080, FZ14130090 or FZ14130100) Battery type Standard battery (FZ14130130) Typical charging time 2 hours 10 minutes Removing the battery Remove the battery as shown below.

Safety information Vehicle safety + Respect national regulations on the use of mobile telephones in vehicles. Road safety always comes first! Always give your full attention to driving. Do not use a hand-held phone while driving. If you do not have a ‘hands free’ car kit, stop and park your vehicle safely before using your phone. If equipped with a correctly installed vehicle kit allowing ‘hands free’ operation and you need to make or receive a call, ensure that it is done sensibly and safely. Use pre-programmed numbers where possible and keep calls short and routine. If incorrectly installed in a vehicle the operation of mobile telephones can interfere with the correct operation of the vehicle electronics, such as ABS anti- lock brakes or air bags. To avoid such problems ensure that only qualified personnel carry out the installation. Verification of the protection and operation of the vehicle electronics should form part of the installation. If in doubt consult the manufacturer. + Do not place the phone on the passenger seat or where it could break loose dur- ing sudden breaking or a collision. Always use the holder. + The use of an alert device to operate a vehicle‘ lights or horn on public roads is not permitted. Emergency calls in Europe, provided the phone has GSM service, emergency calls can be made using the European standard emergency number, 112, even if you do not have a SIM in the phone. Emergency calls can even be made if the phone is PIN or electronically locked or call barred. In some countries local emergency numbers can still be used for emergency purposes but the phone may have to contain a valid SIM card. When making an emergency call remember to give all the necessary information as accurately as possible. The phone may be the only means of communication at the scene of an emergency therefore do not eut off the call until told to do so. 154 able phone re on wireless and lande networks hi cannot be guaranteed in al cond tons, Terre ou hou never rl sol an wireless phones fr sell emergency communi- ctions. Care and maintenance This mobile telephone is the product of advanced engineering, design and crafts- manship and should be treated with care. The suggestions below can help you to enjoy this product for many years. + Do not expose the phone to any extreme environment where the temperature or humidity is high. Do not expose or store in cold temperatures. When the phone warms up after switch on, to its normal temperature, moisture can form inside which can dam- age the electrical parts. Do not attempt to disassemble the phone. There are no user serviceable parts inside. + Do not expose the phone to water, rain or spilt beverages. It is not waterproof. Safety information

Do not abuse this phone by dropping, knocking or violent shaking. Rough han- dling can damage it. Do not clean the phone with strong chemicals or solvents. Wipe it only with a soft, slightiy dampened cloth. Do not place the telephone alongside computer discs, credit or travel cards or other magnetic media, The information contained on dises or cards may be affected by the phone Do not connect incompatible products. The use of third party equipment or accessories, not made or authorised by Mit- subishi Electric, invalidates the warranty of your phone and can be a safety risk. Do not remove the labels. The numbers on it are important for service and other related purposes. + Do contact an authorised service centre in the unlikely event of a fault. AC/DC adaptor chargers This apparatus is intended for use only when supplied with power from AC/DC adaptor chargers (FZ14130070, FZ14130060, FZ14130050, FZ14130080, FZ14130090 or FZ14130100). Use of any other charger or adaptors will invalidate any approval given to this apparatus and may be dangerous. Battery use You can charge a battery hundreds of times but gradually it wears out. When the operating time (stand-by and talk time) is noticeably shorter than normal it is time to buy a new battery. + Do not leave batteries connected to a charger longer than necessary. Overcharging shortens battery life. + Disconnect battery chargers from the power source when not in use. Do not expose batteries to high temperatures or humidity. + Do not dispose of the batteries in fire. They can explode. + Avoid putting the batteries into contact with metal objects which can short circuit the battery terminals (e.g. keys, paper clips, coins, chains etc.). Do not drop or subject the batteries to strong physical shocks. Do not try to disassemble any of the battery packs. Use only the recommended battery chargers (see page 6). If the battery terminals become soiled, clean them with a soft cloth. It is normal for batteries to become warm during charging. Old batteries must be returned to the place of sale or to a place where used batteries are properly disposed of. Do not dispose of old batteries together with household waste. Battery disposal In compliance with European environmental protection directives, used batteries must be returned to the place of sale, where they are collected free of charge. Don't throw away your batteries in your household waste.

Your responsibility This GSM mobile telephone is your responsibility. Please treat it with care respect- ing all local regulations. it is not a toy; please keep it in a safe place at all times and out of the reach of children. Become familiar with and use the security features to block unauthorised use if your phone and/or SIM card are lost or stolen. Call your service provider immediately to prevent illegal use. When not in use lock, turn off the phone and remove the battery. Security codes The phone and SIM card are delivered to you pre-programmed with codes that pro- tect the phone and SIM card against unauthorised use. A short description of each follows. See page 42 to change your PIN and phonelock codes. PIN and PIN2 codes (4-8 digits) AI SIM cards have a PIN (Personal Identity Number). It protects the card against unauthorised use. Some SIM cards also have a PIN2 code that protects specific features such as fixed dialling numbers. Entering the wrong PIN code three times in succession disables the SIM card and the message SIM Blocked. Enter PUK: appears. To unblock the SIM you need the PUK (PIN Unblock Key) code, obtainable only from your service provider. PUK and PUK2 codes (8 digits) Obtain the PUK code from your service provider. Use it to unblock a disabled SIM card (see page 43). The PUK2 code is required to unblock the PIN2 code (see above). Call barring password (4 digits) This password is used to bar various types of calls, made or received, from the phone (see page 43). Voice mail password This password protects you against unauthorised access to your voice mail. Phonelock code (4 digits) This code is set to all zeros on delivery. You can change it. Once changed it cannot be identified by the manufacturer over the phone. Please refer to page 41 for more details. You must remember and make yourself familiar with the purpose and operation of these codes. Disposing of waste packaging The packaging used for this phone is made of recyclable materials and as such should be disposed of in accordance with your national legislation on the protec- tion of the environment. Please take care to separate the cardboard and plastic elements and to dis- pose of them in the correct manner. Safety information

Using your phone For turning on/off the mobile and making/receiving calls, see pages 8 to 11. Standby display Keypad lock To prevent accidental operation of the phone, turn on keypad lock. You can still answer calls by pressing 1. When you end a call, the keypad lock reactivates automatically. To turn keypad lock on Press and hold down @. & appears. To turn keypad lock off Press Unlock /=\ plus @ or press and hold @. You can also use the menu: © Press p: Select Settings. @ Select Phone settings. Select Keypad lock to turn keypad lock on. © Press Unlock /-\ plus @ to turn keypad lock off or press and hold æ. Internet/Wireless Application Protocol (WAP'*) Press Internet /-\ in the stand-by display to access the internet main menu to access your home page or any WAP" portal. You can configure up to 5 WAP"* profiles and 10 bookmarks. See page 54 for more information. Messages (SMS) Press SMS /\ in the stand-by display to access the short messages menu. You can also access it from the main menu. See page 29 for more infor- mation. Backlight operation The backlight is normally off. When a key is pressed the display and key- pad backlight turns on for 10 seconds. If an incoming call is received the backlight turns on and remains on for 10 seconds after the call is an- swered. Important icons + _& displays when you do not answer one or more calls. Press Read /=\ to view the callers numbers if available and the date and time the call was received. Press \L/ to call the number. The phone stores unanswered call numbers in the unanswered calls log (see page 33 for details). +_& appears when you receive one or several messages. Press Read /-\ to view the message or press (D to speed dial your voice mail message centre (see pages 5 and 40 for more details) + _& appears when you receive one or several SMS messages. Press Read /\ to view the SMS inbox message.

If + flashes, your inbox is full. Delete one or more old messages to make space for one or more new messages (see page 29 for more details). The display shows the number and type of messages L il L il Operator Operator Operator 2230 $ L. û L. #02 L. 02 #01 #01 #01 Read SMS] [Read SMS] [Read sms Press Read /-\ to select the type of message you want to read. Press Select /\ or p to view the message. [57 Men one indiatr display ne dati temporry desred. Men bo arte indicate display the time and te are temporal der Dialling from memory You can dial any number stored in the SIM, or the phone memory. To do this from the phone book © Press {to enter the phone book list. @ Use aor v to scroll to the name required © Press \-. In case of a SIM memory contact or of a phone memory con- tact with one number assigned, the phone dials the number. In case of a phone memory contact with many numbers assigned, use A or w to scroll to the number required and press |). The phone dials the number. [9 See page 25 from the calls log memory list The phone stores the last 10 numbers dialled, the last 10 unanswered call numbers (if available) and the last 10 received answered numbers. Q Press p- Select Calls & Times. © Select Calls log © Select Last dial, Unanswered or Received. @ Use A or v to scroll to the number required. © Press |: to dial the number. PA See page 33 Last dialled numbers Quick access to the last 10 dialled numbers can also be obtained by pressing (y. © in the stand-by mode pressing \+) displays a list of the last dialled numbers. @ Use a or w to scroll to the number required. © Press !: to dial the number. [9 The phone stores te last daled numbers in the phone memory, notin te SIL Using your phone

Speed dialling You can assign any key to any telephone number stored in the SIM. To dial such a number: Press and hold down the key (D - ©). The number appears and attempts to connect. By default, (D is always allocated to the voice mail number (see page 44). See page 40 to allocate numbers to the speed dialling keys. Silent and vibrate alert modes To avoid disturbing others you can silence the incoming ring and alert tones. Turning on © Press v. © Select Silent, Vibrate or Vibrate then Ring. w displays when the silent alert mode feature is activated. & displays when the Vibrate or Vibrate then Ring features are activated. Turning off Q rs v. @ Select Ring or Vibrate & Ring. Elfe ringtoe vlume ist 0 à aming message appears in he cispa. Hands free features When you want to share your call with an audience, or you are in your car, use the “hands free” feature. Turning the hands free feature on When making a call Press Speak.on /-\ to turn the hands free feature on during the call- ing process. When receiving a call: Press Speak.on /-\ to accept the incoming call. Turning the hands free feature off Press Speak.off =. Muting You can mute the microphone during a call, e.g. when you want to talk to some- one nearby without the person on the phone hearing Turning the microphone off © Press Options /\. @ Select Mute and select Yes. À warning message appears in the display. #43 also appears. Turning the microphone on © Press Options /\.

@ Select Unmute. A warning message appears in the display. sé disappears. [94 Anew cl restores the microphone to on. Volume adjustment To adjust the volume: ©@ Use «or v to increase or decrease the volume and press OK /-. @ Press Exit /-\ or wait 2 seconds to return to the previous display. [VA See also page 38. Sending DTMF tones Some remote access services require DTMF tones. These tones are used by regular telephones when you dial and when you answer questions from an automated voice service. If you are in a conversation and manually entering the numbers, no extra configuration is necessary. If, however, you want to send a number stored in memory, you must set DTMF to automatic. Manually To send individual DTMF tones directly from the keypad during a conversa- tion: Press the required keys. The tones are heard in the earpiece and sent immediately. Automatically To send a consecutive string of DTMF tones during a conversation: © Press Options /\ e Select Auto DTMF. © Enter the DTMF numbers into the display either directly using the keypad or from a number stored in the phone book (under Names /-)). @ Press OK /-\. The phone sends the tones and then shows the nor- mal conversation display. [51 DIM tnes camnat be sent en à al is on old Pause feature You can enter and store telephone numbers and a sequence of DTMF tones togeth- er as long as you separate them by a ‘pause’. To enter a pause between numbers, press and hold down G. The letter p appears. The phone can store several pauses together for a maximum of 20-46 characters (dependent upon the SIM and the phone memory capacity). Using your phone

Holding and retrieving a call To put a call on hold during a conversation: Press (y. To retrieve a call: Press [L To make a second call when one call is on hold: © Enter a number in the display. Press |] to dial the number. @ After the second call has been established press |+) to swap between the two calls. © To end either the current call or the held call select End active or End held in the Options menu. The remaining call is automati- cally retrieved. @ Press (5/to end the remaining call. [V1 Both call can be ended at the same time by pressing (3). Alternatively, use Options /=\ to display a menu of the actions de- scribed above. Scroll to the required option and press Select /-\ or k (see also "Multi-party or conference calls”, page 21) call waiting, swapping and multi-party conference calls Call waiting Use call waiting, a network feature, to receive a second incoming call when already engaged in a call. This puts an existing call ‘on hold' while you answer or make a second call. To turn the call waiting service on or off: © Press p. Select Settings. Select GSM Services. @ Select Call waiting. © Select Activate or Cancel. The network confirms your request. The confirmation can take several seconds. @ Press Exit/=\or (5) to return to the standby display. Action when receiving a second call You hear a ‘double beep' when your phone receives a second call. An animated phone icon and the telephone number (if available) also appear. To accept the second call Press |. This answers the second call and puts the first call on hold. To reject the second call Press Reject /-\. This returns a busy signal to the second caller. To swap between the two connected calls: Press \L).

Multi-party or conference calls Use this feature to make or receive between 2 to 5 calls at the same time with all parties being able to hear and talk with each other. © Make and establish a call in the normal way and press {L) @ Enter another number into the display and press \L. The first call is put on hold when the second call becomes active. © Press Options /-\for the following menu: Option Description Auto DTMF | to enter a DIMF string to the active call only Swap Swaps between active and call on hold Toins active and call on hold to make a multi-party or Join conference call Mute/Unmute_ | Tums on or off the microphone End held Ends the call on hold Ends the active call and connects with the call on Endactive | End all Ends all the calls Allows you to select and have a private conversation

• Private with | with one of the conference callers while putting all the other calls on hold Hoïd/Retrieve | Hoïlds or retrieves the conference call Allows you to select and end one of the conference

Endone | Ci participants These items in the Options menu appear if more than 2 calls are joined in the conference call. Throughout the conference call the display confirms and shows the ac- tions you selected from the options menu. [91 For ltemate line service (ALS), you cannot make subscribers conference calls betueen Line 1 and Line 2. Using your phone

The menu Use the round cursor key to access the menu system. Your menu options can vary. Some may not appear. This depends on your network operator and your subscription Access to the menus Press 4 to view all stored telephone numbers. Press to enter the main menu. Hold down Exit /=\ or press (3) to exit the menus (if no call is in progress). Menu map Internet Home page Network Server Bookmarks Applications Other site Services Currency Profile list Information Settings Games Phone Book Reshape Recall Push Store Options Remaining Own numbers Office Tools Fixed dialling Scratchpad Phone book Alarm clock tones Auto-switch Calculator Messages Inbox Settings Outbox Phone settings Write new Voice mail Que vs GSM Services Call log on texts Broadeast Call timers os orage Call costs Line selection Items in italics depend on your subscription and your network operator. Entering text To add names to the phone books (see page 25) and write text messages (see page 30) you must enter text. The phone displays 44 in lower case mode and 44 in upper case mode when you can enter text. Use the keypad to enter/edit text You can enter text/numbers using T9 text entry or Multitap text entry.

T9 text entry Press w to swap between T9 text entry and the Multitap method. To enter text with T9:

Press the key with the required letter only once. Do not be put off if the character you want is not immediately dis- played. The ‘active’ word changes as you type, so type to the end of the word I your word is not displayed, press @ for other matching words. H your word is not recognised, press w to swap to the Multitap method to complete the word Use {or p to locate the cursor in the text to insert characters or make corrections. Tips and operation Rey Action æ Rift - upper/lower case Clear Tiear or backspace Press and hold | Numbers æ pace © mother matching word œ Smart punctuation + wap between T9 and Multitap method Example To enter Card in the display: Press b and select Messages. Select Write new. + Press T appears. + Press @. À appears. + Press @. Ca appears. + Press @. Car appears. + Press @. Case appears. If the displayed word is not the one you want, press © as many times as necessary to view Card. + Press (3 to exit from this example and return to the stand-by display, Multitap text entry Press on w to swap between T9 text entry and the Multitap method. To enter text with multitap:

Press the key with the required letter. Ifitis not the first letter, press key repeatedly until the letter appears. See the table that follows for a key to character correspondence. Enter the next character. If two characters are on the same key wait for the display at the top of the screen to clear or press p be- fore pressing the same key again. The menu

© To access special characters (23 availa- ble), hold down &. A table appears. Press the key that corresponds to the

character. a/© 9/5 0! w Exit @ Press Clear /\ briefly to correct back one letter. Hold down to clear all text. © Press 4or p to move the cursor in the text to insert characters or make corrections. The following table displays the available English characters. Other lan- guages display different character sets. Key Character Towercase Upper case T,-@:7 abcz ABCZ e] def3 DEF3 æ ghi4 GHI4 ® LE TKL5 G] mnoë MNOG œ pars? PORS7 D Tuvs TUVE œ wWxy29 WXYZ9 © 0 ü æ Short press swaps next letter between upper or lower case. Long press swaps all next letters between upper or lower case. Short press, enters space. O] Long press gives access to special characters. O%l;:"_@SsS+#*/&=<>Y$f£Lice + Short press moves the cursor through the text one place. + Swap between Multitap and T9 Example To enter Card in the display: + Press b and select Messages. + Select Write new. + Press and hold G until 44 appears. Press @ briefly three times, C appears. + Wait for the available characters to go from the display, press and hold @ until 44 appears. Press ( briefly once, a appears. + Press @ briefly three times, r appears. + Press @ briefly once, d appears. The word Card appears. + Press (2) to exit from this example and return to the stand-by display.

Network services a | Your network operator provides value added services and contact phone numbers. Depending on your operator's implementation Applil ions, Services, and/or Information appears in the display. Press b and select Network Services to ac- cess these menus. Phone book

The phone book stores data, usually names and telephone numbers, in the phone or SIM memory. + The phone can store up to 100 ‘phone phone book cards’ which can contain: family name, first name, icon, home phone number, work phone number, cellular phone number and a note. + SIMs can store up to 255 ‘SIM phone book cards’. Actual numbers and capacity depends on your SIM. SIM phone book cards only contain the name and number. Both the SIM and the phone memories are searched when you use the phone book. String names and telephone numbers You can enter the names and numbers in the phone book manually or copy them from SMS messages, scratchpad or last dialled number lists, etc. You can store the characters *, +, P (pause), # and _ together with numbers. See page 22 to learn how to enter text. Store numbers in international format using the '+' prefix (or 00) before the country code followed by the telephone number. This ensures that the number can also be dialled from abroad. There are several ways to store numbers into the phone or SIM memory: Phone memory + Directly from the stand-by di Enter the number. Press Store /-\. @ Select Phone names. @ Alist appears. isplay Select the item corresponding to the number you entered: home, work or cellular. @ The following fields appear: Field Purpose Family name Family or last name First name First name © Enter the requested data. Confirm each entry by pressing OK /-\. The menu

@ Select an icon. The icons correspond to D - @ keys on the keypad. Press the key corresponding to the required icon. In this example pressing @ selects ei. @ The following fields appear: Field Purpose Phone number (Home) Home phone number Phone number (Work) Work phone number Phone number Cellular phone number {Cellutar) Note Note or comments for this card @ Enter the requested data. Press OK /-\. Confirmation and number of free locations appear. © Press Exit /-\ or (3) to return to the stand-by display. + Using the menu: © Press p: Select Phone Book @ Select Store. Select Phone names. © Follow the steps in the previous procedure (“Directly from the stand-by display") starting with step ©. + From last dialled, received and unanswered lists: © Display a number from one of the above, then press Options /-\. @ Select Store. Select Phone names. © Follow the steps in the “Directly from the stand-by display" pro- cedure starting with step ©. [74 Duing number and name entry à shot pres on Car earth as character, A long press cars the whole display, SIM phone book memory You can enter the SIM memory from the stand-by display, menu or other locations. irectly from the stand-by display: Enter the number. Press Store ;- Select SIM names. Press OK /-\. Modify or confirm the number and press OK /- Enter the name. Press OK /”\. Confirmation and number of free locations appear. Press Exit /-\ or (5) to return to the stand-by display. + Using the menu: © Press p. Select Phone Book

@ Select Store. Select SIM names. © Enter the number and press OK Enter the name and press OK /-\. Confirmation and number of remaining locations appears. © Press Exit /-\ or (5) to return to the stand-by display. + From other stored locations Numbers stored in the last dialled, received, unanswered, scratchpad and SMS message locations can all be stored in the phone book: © Display a number from one of the above then press Options /—\. © Follow the steps from the previous procedure “Using the menu” starting with step @. [1 During number and name entry à shot pres near cers els chart, Ang pres cars the whole display, Awarning message appears when selecting the phone book when the SIM or phone memory is full. Free space in the phone book To see the remaining free space in the SIM or phone: © Pres p- Select Phone Book. @ Select Remaining and use A or w to display the remaining memory spaces in the phone or SIM. © Press Exit /\ or (3) to return to the stand-by display. {9 available, the free memes in the FDN is also appears. Viewing and calling numbers in the phone book You can edit, delete, copy, move or access phone book entries stored in the phone or SIM. There are two ways to view and call numbers in the phone book: + Directly from the stand-by display. Press {to display the phone book list. + Using the menu: © Press p and select Phone Book. @ Select Recall. © Eïither press OK /=\ or enter up to the first 3 initials of the name required and then press OK /=\. Pressing A or w scrolls through the phone book. To go directly to an- other entry press the corresponding alphabet key. For example to go directly to entries starting with 'N' press © twice. If you did not enter any initials, the phone book displays the first entry. © Press |) to dial the number. If there is a choice of numbers for the phone book entry, these appear. Select the one that corre- sponds and press |). The menu

Pressing Options /-\ displays the following menu choices: em Function Edit | Edits the name and number entry Delete_ | Deletes the entry Send | Sends SMS message Copies the entry to the SIM or the phone or vice ver- sa. You can edit before copying Moves fhe entry to another position. You can edit be- fore moving Calls the number displayed or (3) to return to the stand-by display. Own number display The phone can display to your correspondent your main ‘Line 1' voice mo- bile number, the voice mobile number for Line 2 (Alternate Line Service) and your data and fax numbers. The SIM stores these numbers. You can enter them manually and name them. For example, you can name Line 1 ‘Office’. To view, name and edit your own display number(s): Q Pres p- Select Phone Book. Select Own numbers. The mobile number for Line 1 appears. Use A or w to view line 2, data and fax numbers. To add or edit a name or number press Edit /=. Press Exit or \3/ to return to the stand-by display. Fixed dialling numbers (FDN) Fixed dialling only allows you to call a group of numbers. All other num- bers are rejected. FDN also prevents call diverting and sending SMS mes- sages to numbers not in the FDN list. You can use wildcards to define the groups. As this is a SIM dependent feature, some SIMs might not support it. SIM capacity determines the maximum number of FDN numbers you can configure. To activate/deactivate FDN you must have the PIN2 code. To turn on or off FDN operation: ©Q Press p- Select Phone Book. © Select Fixed Dialling. Select Status. © Select On or Off. Enter the PIN2 number. @ Press OK /-\ to confirm the setting. To view the numbers in the list: © Press p Select Phone Book. © Select Fixed Dialling. © Select View and use À or w to scroll through the entries. Press Options /=\ to edit, delete and copy numbers to the phone or SIM. To enter, edit or delete numbers in the FDN list: © Press p. Select Phone Book. G00©

@ Select Fixed Dialling. © Select Add new. Enter the PIN2 number if asked. Add, edit, delete or copy new numbers to the phone or SIM. 91 You can use lé card spaces uit numbers store in te FDN is. For example the number + 441707 278. Salons you to al all numbers betveen 278009 to 278990 Phone book tones 30 pre-set ring tones are available, 10 with tri-tones (generally sound bet- ter) and 20 with mono-tones. Storage of up to 40 ring tones is possible. That is, you can add one self-composed ring tone and 9 other ring tones you download in addition to the existing 30 ring tones. If you want, you can replace any of these ring tones except the Trium ring tone. You cannot replace the memory space used for the self-composed ring tone. To have different tones for incoming calls where the identities are known in the SIM or phone memory: Q Pres p- Select Phone Book. © Select Phone Book Tones. © Select Phone names or SIM names. Press Select /-\. @ Select the tone you want and press Select /\. The phone stores your selection. Messages (SMS) FES) You can exchange short text messages of up to 160 characters with other mobile phones with SMS. You can also store, edit and forward messages and save any of the numbers they contain Reading a received SMS message When the phone receives an SMS message a new SMS alert tone sounds and 4 appears. The SIM stores the message. If # flashes there is no more space in the SIM to store new messages. Delete previous messages to make space for new ones. Press Read /-\ to read all received messages (Inbox). Reading stored SMS messages Q Press p- Select Messages. © Select Inbox to display the first message header. @ Use à and w to select the message. © Press p or select Options /-YRead text to read the message text. You can now read all stored messages. For a given message, 13 shows the message is new. FE shows you have already read the message. The menu

Managing received and stored SMS messages After reading the SMS message press Options /=\ for the following menu: Hem Function Read text | Displays the remainder of the text Delete | Deletes the message Reply Replies to the sender of the message Reply Replies to the sender of the message with the (+ text) initial text Forward | Forwards the message {0 another user Forward E0 n | Forwards a set of several (5 maximum) messag- es to 5 different addressees Stores or calls the number(s) contained in the Numbers | sus header or text [V2 The items of this menu depend on the type of message received. Turning on or off the message alert tone Each time a message is received the SMS alert tone sounds. To turn on or off this tone: © Press p. Select Messages. @ Select Alert. Select On or Off. © Press Exit; or (5) to return to the stand-by display. Preparing the phone to send SMS messages You can write and send text messages. To use SMS, check that the number for the message centre is configured: Q Press p- Select Messages. © Select Settings. © Select Message centre. If a number appears do nothing. If empty, enter the number manually {in international format) or from a stored memory. If you do not have this number, ask your service provider for it. @ Press Exit /-\ or (5) to return to the stand-by display. Ifrequired you can also choose the validity period, format, paid reply request and request a delivery report. Default settings are assumed if not set. Option Description Default Time held at message centre. Maximum Validity Period | 12 hours, 1 day, 2 days or Maxi- mum (defined by operator) Selects format of message, text, |Text Format voice, fax or pager Paid Replyto | Reply requested off Status report to _ | Delivery report Qi Creating a draft text Parts of a message are often the same, such as the greeting or signature.

To save time, you can create a draft text with these parts. Then when you want to write a message, you access the draft text and only write the spe- cific part of the message. You can set up to 10 message drafts, which can hold up to 50 characters each. Your total message, when complete can only be up to 160 characters. The mobile memory stores the drafts. To create a draft text: Press p. Select Messages. Select Draft texts. Choose any blank template ([...]) and press Edit / Enter the draft text and press OK /=\. Press Exit /-\ or (5) to return to the stand-by display. Editing a draft text Press p. Select Messages. Select Draft texts. Select the draft text to modify and press Edit /\. Edit the text and press OK /-\. Press Exit /-\ or (5) to return to the stand-by display. a new SMS message to one addressee Press p. Select Messages. Select Write new. You can either choose a draft text (if you set one up) or enter the message text and press OK ;-\. Select Send. Choose a message template and then enter the destination number or select Names /=\ to choose a number from a phone book entry. Press p to validate your choice. Press OK /=\ Sending and sent confirmation appears for each addressee. @ Press Exit /-\ or \3/ to return to the stand-by display. Sending a new SMS message to many addressees Press p. Select Messages. Select Write new. You can either choose a draft text (if you set one up) or enter the message text and press OK /\. Select Multicast. Choose a message template. Enter up to 5 destination numbers or select Names /=\ to choose up to 5 numbers in the phone book. Press b to validate your choice. Press OK /\. Sent confirmation appears. Press Exit /-\ or \3/ to return to the stand-by display. GOCCE GeCC® Sendin

Storing a new SMS message Q Press p Select Messages. © Select Write new. © You can either choose a draft text or enter the message text and press OK /—\. Select Store. © Press Exit /\ or \5/ to return to the stand-by display. Modifying and re-sending messages in the outhox The outbox contains unsent draft messages, stored sent messages and sent but undelivered messages. You can modify and re-send these as new messages. To select an outbox message: © Press p- Select Messages. @ Select Outbox and use « or w to scroll to the desired message. Messages are either “transmitted” ( #2 ) or “to be sent” (+). © Press Options /-\ to read, delete, request a status report, send (or re-send) to one addressee, edit a sent message and send (or re-send) to many addressees. @ Follow the instructions displayed on the screen. Status request on sent messages If you request the status of a delivered message the delivery date and time appears. If you request the status of a sent message the network sends a status report (if this feature is supported). Press OK /-\ to acknowledge the report. To act upon a received status report and its related message: © Press Options /\. The following menu appears: Hem Action Deletes the corresponding sent SMS message and the status report To acknowledge the status report and clear the Delete message Clear display Associated | Dicplays the corresponding sent SMS message message Send'agaim | Sends Ie same message again © Select the action required and press OK /\. Re-usable message templates The Msg templates menu option appears in the Messages - Settings menu if your SIM supports this feature. Message templates are sets of mes- sage parameters and are stored in SIM memory. You can name and select the templates when needed. To create a message template: © Press p- Select Messages. Select Settings. © Select Msg templates. Choose any blank template ([..]).

© Enter the template Name, Message centre number, Validity period and Format. Default settings for pay reply and status are assumed ‘off unless set and are common to all templates. If you only set one template the phone uses it by default. Otherwise select the template you want when sending a mes- sage. Storage consumption To consult the memory used by SMS: Q Press p. Select Messages. @ Select Storage. à Use a or v to view all the SMS storage information (SMS stor- age, SMS outbox and SMS inbox). © Press Exit /-\ or (2/to return to the stand-by display. Calls & Times Access the Calls & Times menu to check the details of individual incoming and outgoing calls, the duration of the last call or the total time for all previous calls. Calls log Calls log stores the identity, time, date and call duration of the last 10 numbers dialled, the last 10 received unanswered calls and the last 10 received calls. The call logs are common for both Line 1 and Line 2. Q Press p- Select Calls & Times. @ Select Calls Log. © Select Last dial, Unanswered or Received. @ Use a or w to scroll through the list If the caller's number is not available Unknown number appears (unan- swered and received lists) Pressing {L/ while on a displayed number calls that number. Pressing Options /=\ accesses the following menu: Hem Action Store Stores the number in the phone book Delete Deletes the entry Delete all |Deletes al the entries Edit Edits the displayed number Details Views the details - name, number, time and date and call duration of the highlighted number Tam Makes a call to the number Send SMS | Sends SMS message Use À or y to select the required option and follow the display prompts Press Exit /-\ or (3) to return to the stand-by display. [V1 Press \ ven in stand-by display to access the last 10 dalle cal Call times Call times stores the duration of the last call, total accumulated time of all The menu

calls and total time for Line 1 and Line 2. The Details /-\ sub-menu stores times for calls made and received through the subscription network and through other (national and international) networks. Press p. Select Calls & Times. Select Call timers. Select Show. If you reset the call timers (see page 35) the date of the last reset of the counters appears briefly. Use À or w to view all the timer information. The call type and the accumulated times of outgoing and incoming calls appears. 600® All calls 2? 00:12:47 << 01:07:48 Details + Exit © Press Details /=\ to display details of roaming and international calls. @ Press 4or Exit /\ to return to the previous display. Press and hold Exit /=\ or (£/ to return to the stand-by display. 9 Line 2 is subsoribed to AI Call for Lie 1 and Line 2 appear separatel Balance information (subscription service only) Some networks provide your remaining airtime balance. You have to call a specific number (given by your network operator) in order to get this in- formation. Contact your service provider for availability and details. Press p. Select Calls & Times. Select Balance information. Select Set number (only necessary the first time you use this service) to check that the balance information centre number is set. If not, enter the number provided by your service provider and press OK /\. © Select Call. The phone calls the centre. Press \5/ when you want to end the call. @ Press Exit /—\ or \5/ to return to the stand-by display. Reminder - Call duration You can set a call duration reminder in multiples of 1 minute (1 - 59 min.) intervals. It beeps at the set intervals. © Press p. Select Calls & Times. @ Select Call timers. à Select Reminder.

Select On (or Off) Select the period (between 1 and 59 mins). ©6606 or (/ to return to the stand-by display. Call timer - reset To reset all the call timers, you need the 4 digit phone lock code. Press p- Select Calls & Times. Select Call timers. Select Reset. Select Yes or No. Enter the phone lock code and press OK /=\ Press Exit /-\ or (5) to return to the stand-by display.

GGOO© Call costs - management (subscription service only) An Advice of Charge (AoC) subscription service shows the cost of the last call made, the accumulated total cost of all calls and the remaining balance in units or currency of any ‘cost limit’ you set. Check with your service pro- vider to see if they offer this feature. Select the currency and cost per unit; othenwise call costs display in generic units. To set currency and cost per unit: Press p.. Select Calls & Times. Select Call costs. Select Display cost type. Select Currency. The present currency settings appears. Press Edit /=\. Enter the PIN 2 code and press OK /\. Enter the abbreviated letters of the currency. Press OK /-\. Enter the cost per unit in the selected currency. Press OK /- © CG0600® /\ or \&/ to return to the stand-by display. To set call cost type to units: Press p. Select Calls & Times. Select Call costs. Select Display cost type. Select Units. Press Exit /-\ or \z/ to return to the stand-by display.

91. When you st te cost type to unit the credit limit and te remaining credit appear in units.

Setting the credit limit - in units or currency You can set a credit limit in units or currency. The phone prevents making and receiving all chargeable calls when the phones reaches the credit limit. You can still make emergency calls. © Press p. Select Calls & Times. @ Select Call costs. GOCC®S The menu

Select Credit Limit. The present credit limit setting appears. Press Edit /—\. Enter the PIN 2 code and press OK /-\. Enter the credit limit (use @ to enter a decimal point). Press OK /-\ to validate. Press Exit or \3/ to return to the stand-by display. [91 Men you enter à edit imi ne selection fom the "Credit Limit dspays Et or Set No Limit Show costs Press p Select Calls & Times. Select Call costs. Select Show. Use A or w to display the cost of the Last Call, AII Calls and the Remaining credits. Press Exit /=\ or (3) to return to the stand-by display. {9/1 Te Cost Thpe menu units or curency seing detemines whether the remaining cet displays uni or eue. Call costs - resetting all costs to zero To reset all the call costs to zero you need the PIN 2 code. Press p Select Calls & Times. Select Call costs. Select Reset. Select Yes to reset the costs or No to exit. If you select Yes, enter the PIN 2 number and press OK /-. AII Costs Reset appears briefly. © Press Exit /\ or (5) to return to the stand-by display. Alternate line service - selecting line 2 (subscription service) Some GSM 1800 operators support the use of a second line for users. You can have two mobile phone numbers, e.g. a business and personal line. To select the line for outgoing calls: Press p. Select Calls & Times. Select Line selection. The current line selection appears. Use À or w to scroll to the line required and press Select /=\ or p to validate your choice. Press Exit /-\ or (3) to return to the stand-by display. [91 You cn assign names t Line 1 and Line 2, € 9. Of and Home, Se page 28 for details. You must select te line to make outgoing call. You can receive cal from either in. Settings - customising your phone Phone settings Keypad lock See page 16 for more information: 6 ©&060©

Language selection To select the language of your choice: © Press p- Select Settings. Select Phone settings. Select Language. Use A or w to select a language from the displayed list. Press p to validate. @ Press Exit /-\ or (5) to return to the stand-by display. 9 To reset phone to tne language ftne SIM enter*# 0000 To reset the phone language o Engin enter *# 0044 Tones - Alert mode To turn on or off the audible incoming ring tone, alert and alarm tones: + Using the menu: Press p. Select Settings. Select Phone settings. Select Tones. Select Alert tones. Select Ring, Vibrate, Vibrate & ring or Vibrate then ring. /\ or \&/ to return to the stand-by display.

Press E: Directly from the stand-by display: Press w displays Ring, Silent, Vibrate, Vibrate then ring. Scroll to the desired setting. Press p to validate your choice. (If any of the vibrate options are selected the phone briefly vibrates). & appears. 9 1: fyou select Ring ut the ing tone volume off the icon appears.

2. ex appears ou select Vibrte, Vibrte& ing or Vibrate ten ng takes precedence

3. When he phone is connected o her ne Desk Top Charge, HF Ki, CLA or AC adaptor the

phone rings instead of ibraes

4.1 you chonge the Wibrae or Vibrate then ing option, he vibreting acon replaces al the alert

and âlèrm tones. Ring tone selection To choose an incoming ring tone: ©Q Press p. Select Settings. Select Phone settings. Select Tones. © Select Melodies. @ To help you identify incoming calls you can give the Standard/ Line 1, Phone names, SIM names and Line 2 calls and Alarm different ring tones. Use À or w to highlight the required call type and press p to select it. @ Use a or v to listen to the different ring tones. Press p to select the current tone. \ or (3/ to return to the stand-by display. ibrate & ring or © ©.0600® The menu

Volume adjustments To individually adjust the volume level of the ring tone, key tones, alarm tones and incoming audio from the stand-by display, press A. Alternatively, access Volume control from the Settings menu: Press p. Select Settings. Select Phone settings. Select Tones. © Select Volume. @ Select Ring, Keys, Conversation or Alarm. The display confirms the selection, naming the volume to be adjusted.

volume Use À or w to adjust the setting. 8 Press OK /=\ to validate the setting. @ Press Exit /-\ or (3 to return to the stand-by display. During a call, you can adjust the conversation volume by using A or w. [91 Ifthe ring tone volume level is set to D w displays. Ramping Ramping causes the incoming ring tone to increase in increments to the maximum volume level. Press p. Select Settings. Select Phone settings. Select Tones. Select Volume. Select Ramping. Select On or Off. Press Exit /=\ or (5) to return to the stand-by display. [91 When tumed on the volume of the incoming ring tone starts from the minimum and rises to the maximum volume unël answer Melody composer To compose your own melodies: Press p. Select Settings. Select Phone settings. Select Tones. Select Melody composer. [INT]

[IN] © Select Edit. © Enter notes using the keypad (see table below): Not | © D E F G A B Key ©] e] œ @ E] © Li] Select Play to play your melody or Delete to delete it. Press Exit or \3/ to return to the stand-by display. Use the actions in the following table to modify the notes. The tempo 8 Select OK. The phone stores your melody

is fixed. Symbol Action P Use @ to insert the P’, which inserts a pause +1- Press À after a note to increase it one octave (+ appears) or press w to decrease it one octave (- appears) F Use @ after a note to increase the note one half-tone 2, 3074 [Usekeys @, © and © after a note to increase the length " of the note by 400 ms, 600 ms or 800 ms Melody download You can also download melodies from the Trium web site. This site downloads the melodies to your phone using SMS. When the down- load completes, Press Options /- Press Options / Backlight - setting To set the backlight during key entry or incoming ring tone, you have two options: + On for 10 sec.: the display and key backlight stays on for 10 seconds after the last key press or incoming call. + Off: the backlight stays off. Press p. Select Settings. Select Phone settings. Select Display. Select Backlight. Select one of the two settings. Press p to validate. Press Exit /—\ or (3) to return to the stand-by display. Display contrast To modify the display contrast because of bad light conditions: 2 Press p- Select Settings. Select Phone settings. Select Display. Select Contrast. Adjust the contrast using A or w. Press OK /-\ to validate the setting. @ Press Exit /-\ or (5/ to return to the stand-by display. Menu graphics Choose from a set of graphics to personalise your main menu images, and icons. There are 5 menu themes which all have night and day idle screens. The idle screen changes to the night one at 9 p.m. and to the day one at 7 am. To change the menu graphics: Press p. Select Settings. @ Select Phone settings. Select Menu graphics. à Use aor v to scroll to the sets of menu graphics and press Select /\ or p to validate your choice. and then select Play to play the melody. \ and then select Install to store the melody. GECCO The menu

@ Press Exit /-\ or \S/ to return to the stand-by display. Any key answer To enable any key (except (5) and No ring /- an incoming call: Q Press p- Select Settings. @ Select Phone settings. Select Keys. © Select Any key answer. @ Select On or Off. © Press Exit / or (3) to return to the stand-by display. Softkeys - programming the softkeys You can change the function of the softkeys. There are two ways: + Directly from the stand-by display: Press and hold down the left /—\ or right /-\. Use A or w to scroll through the choice of softkey options. Press Select /\ to validate your choice. The screen confirms your selection and returns to the stand-by display showing your new softkey function. + Using the menu: Press p. Select Settings. Select Phone settings. Select Keys. Select Softkeys functions. Select Left softkey or Right softkey. Press Select /=\ on the softkey option of your choice. Press Exit or \3/ to return to the stand-by display. in te display means that a previous SIM dependent or subsipton seice assgned to that sole is no longer aailble. Far example Line 2 selection. Speed dialling You can assign phone book numbers to keys @ - ©. Hold down the key to dial the number. The phone reserves @ exclusively for the voice mail number, The phone assigns this automatically when you (or the SIM) store(s) the voice mail number (see Voice mail, page 44). You can select any stored number. To assign phone book numbers to the speed dialling keys: Press p. Select Settings. Select Phone settings. Select Keys. Select Speed Dial. Use A or w to scroll to the next key. Select Names /-\ to choose the phone book entry and press Select /-\ to validate your choice. Press Exit /-\ or (3) to return to the stand-by display. 9/1 1 You delete the number from te phone book this delete from te es, ) to be pressed to answer 60c® 6G6000® 6 G600®

Auto answer This feature only works when you connect the phone to a hands free car kit or headset. The phone automatically answers an incoming call after approximately 5 seconds. © Press p- Select Settings. @ Select Phone settings. Select Auto features. © Select Auto-answer. @ Select On or Off. © Press Exit /-\ or (5/ to return to the stand-by display. Auto-retry To automatically retry the number of a failed call (up to 10 times): Press p- Select Settings. Select Phone settings. Select Auto features. Select Auto-retry. Select On or Off. Press Exit /-\ or (5/to return to the stand-by display. 26 CCE When activated, Auto-retry and a countdown timer to the next call attempt appears. An auto-retry warning tone sounds each time the phone attempts a new retry. lf successful, proceed with the call as nor- mal. Press Exit /=\ or any key during the retrying process to cancel auto-retry and end the dialling process for that call. Security features The security features described in this section protects your phone from unauthorised use. For all codes When requested, enter the code, which appear as asterisks (*) and press OK /=\. If you make a mistake press Clear /=\ and enter the correct digit(s) be- fore pressing OK /=\ [V1 Avoid using codes similar to emergency numbers such as 999 or 112 to prevent accidental dial ing ftese number. KEEP A RECORD OF YOUR CODES AND KEEP THEM IN A SAFE PLACE. FAILURE TO DO SO CAN CAUSE YOU CONSIDERABLE INCONVENIENCE. Phone lock code A phone lock code prevents unauthorised access to the phone and WAP" settings. You also need it to reset the call timers. The factory setting is 0000. Reset this code and keep it in a safe place, separate from the phone. When enabled the phone asks for the code each time the phone is turned on. To change the phone lock code: © Press p: Select Settings. @ Select Phone settings. Select Security. The menu

Select Phone lock. Select Change code and follow the display prompts. Press OK ;-\ to validate the new code. Press Exit /=\ or (5) to return to the stand-by display. o turn on or off the phone lock code: Press p Select Settings. Select Phone settings. Select Security. Select Phone lock. Select On or Off. The phone requests the phone lock code to authorise your selec- tion. Press Exit or \3/ to return to the stand-by display. [91 Phone lock il enable ou to make emergency ls. PIN code The 4-8 digit PIN code for the SIM protects it from unauthorised use. When enabled the phone requests the PIN code each time the phone is turned on. If you enter the wrong PIN code three times in succession your SIM card is blocked and you need the 8 digit PUK code from your service provider (see page 43). To turn on and off the PIN: © Press p. Select Settings. © Select Phone settings. Select Security. If already off, PIN enable appears. If already on, PIN disable and PIN change appear. © Press Select /-\ and follow the display prompts. @ Press OK /=\to validate your entry. PIN enabled or PIN disa- bled appear briefly to confirm your action. © Press Exit /-\ or (3) to return to the stand-by display. To change the PIN code (PIN must first be enabled): © Press p. Select Settings. © Select Phone settings. Select Security. © Select PIN change and follow the display prompts. © Press OK /"\to validate your new PIN. © Press Ex \or (3/ to return to the stand-by display. PIN2 code The PIN2 code prevents unauthorised access to FDN operations, modify- ing the FDN phone book, setting calls costs to zero, modifying the costs display features. You can change it but you can not turn it on or off. To change the PIN2 code: © Press p. Select Settings. © Select Phone settings. Select Security. © Select PIN2 change and follow the display prompts. G6O00® -6G60©

@ Press OK/-\ to validate your new PIN2 code. © Press Exit /-\ or (5 to return to the stand-by display. PUK code Only your service provider can give you the 8 digit PUK (PIN unblock key). Use it to ‘unblock a PIN whose code has been entered incorrectly three times. À PUK code cannot be changed. Enter the PUK code and press OK /=\. Enter a new PIN code by follow- ing the display prompts. 91 you enter the wrong PUK code 10 times in succession you SIM card cannot buse again. Co tac your sen provider for à ne ar PUK2 code Only your service provider can give you the 8 digit PUK2. Use it to un- block a PIN2 whose code has been entered incorrectly three times. You cannot change the PUK2 code. Enter the PUK2 code. Enter a new PIN2 code by following the display prompts. [91 1f you enter the wrong PUK2 code 10 times in succession you âre unable to use the features requing he INA code. Conte our senc proider fr à new card Call barring password Use the call barring password to select the call barring levels outlined in the GSM Services - Call barring menu (see page 48). Your service provider gives you the initial password. To change the password: © Press p. Select Settings. @ select GSM Services. Select Call barring. © Select Change password and follow the display prompts. © Press OK/-\ to validate. © Press Exit /-\ or (5) to return to the stand-by display. Summary of code/password entry chart Number of tries blocked or P: rd | Length asswo ns) allowed forgotten Phone à cigits Unlimited Return phone to manufac- unlock code turer PIN pu] te Unblocked by use of PUR digits code PIN2 48 3 tes Unblocked by use of PUK2 digits code PUK 8 digits 10 tries Contact your service pro- vider PUR 8 digits tie Contact your service pro- vider CM barrng | à digits Network Contact your service pro- password g determined vider The menu

Time & date setting To set the current time and/or date: GG 600€ Press p. Select Settings. Select Phone settings. Select Time & date. Select Set time or Set date. Enter the time (in 24 hour format) or date in the format shown. (If required use and p) Press OK /=\ to validate your selection. Press Exit /-\ or (3) to return to the stand-by display. 9 1 An erar message appeas if you make a wrong entry

2. The time/date displays men tre phone is on. does not Shou the year.

3. An itemal battery maintains the date and time getting for up to 3 hour en te phone is

sitched of and without a battery, or tn a completely discharged battery atacheë, fer this te you must rest the clock (needed) uen you suieh an tne phone. Default (factory) settings Use the Settings menu to return to the factory settings. This does not affect the phone book entries, phone lock code or SIM. © Press p- Select Settings. © Select Phone settings. Select Default settings. © Select Yes or No. ©@ Press Exit /-\ or (3) to return to the stand-by display. The following are the factory default settings: Feature Factory setting Alert Tones Ring Ring Tones Trum Volumes, Ring, Key, Speech and Alarm Mid values Backlight and Contrast On for 10 sec. and mid value Any Key, Auto-Retry and Auto Answer off features. Ramping Qi Menu graphics Trium Voice mail Voice mail operates like an answering machine. Contact your service pro- vider for details. Storing a voice mail centre number If your SIM does not automatically include the voice mail centre number, you must manually set it: Go ©c0® Press p. Select Settings. Select Voice Mail. Select Number. When prompted enter the number manually or from a stored memory. Press OK /=\ to validate your entry. Press Exit or \3/ to return to the stand-by display.

[PA you subscibet he Une 2 senice, store the voice mal centre number separte or that ie. he phone automatialy asigns the voice mail number to speed dial location number 1 (see Speed diallig on page 40. Turning on/off the voice mail alert tone To turn on/off the voice mail alert tone: © Press p- Select Settings. @ Select Voice Mail. à Select Alert. Select On or Off. © Press Exit /-\ or (5/ to return to the stand-by display. Calling the voice mail centre to check for messages There are two ways: + To dial the voice mail centre directly after the receipt of a message: Press and hold down D. + Or from the menu: © Press p- Select Settings. @ Select Voice Mail. à Select Call. Dialling proceeds as for a normal call. EP If vice mail number is not store en you select Gal, he phone ask you to ete the vice mal number Proceed as desaibed in String a voic mal centre numbe, päge 44. GSM services Diverting incoming calls (network service) Call diverting diverts incoming calls, whether voice, fax or data, to an- other number. To turn on call divert: © Press p Select Settings. @ Select GSM Services. Select Call diverting to access the follow- ing menu: Divert options Action Always Diverts all incoming voice calls unconditionally When not | Diverts all voice calls when the phone cannot be reachable | reached, i.e. out of service Diverts all voice calls when the phone does not an- Onnoreply | er When busy | Diverts all voice calls when the phone is busy Diverts all voice calls when Not Reachable, No Re- ply and When Busy Tancer al | Cancels all diverts AITFAX calls | Diverts unconditionally all incoming fax calls AITDATA calls _|Diverts unconditionally all incoming data calls @ Usa or v to select the divert condition and validate by press ing Select /-\or p. © Select Activate. All conditions The menu

Use À or w to choose between Voice Mail, Names or Number. Press Select /-\ or p to validate your selection. The display confirms your request. © Press Exit /-\ or \5/ to return to the stand-by display. [V1 1: If you select On no repy' option you must also enter a delay period of 5, 15 or 30 seconds.

2. al der for both Line L nd Line 2 must be et ndhiduall. Select ne ou gong in beore

foloning te above procedure To car out a al iv on te ler ie ou must sect hist line fs menu Cl & Times - Line sélection)

To turn off or check the status of call divert: © Press p. Select Settings. @ Select GSM Services. Select Call diverting. © Select from the divert options and press p. © Select Cancel or Status. The phone confirms your selection. © Press Exit /-\ or (5 to return to the stand-by display. To cancel all (multiple) diverts: Press p.. Select Settings. @ Select GSM Services. Select Call diverting. © Select Cancel all. The phone confirms your selection. @ Press Exit /-\ or (3) to return to the stand-by display. {9 This action nc al voice divers or voice, fves and data al for the line current in use, To cancel call diverts for the other line you must select this other line fist (menu Calls & Times - Line selection). Caller Line Identity - showing/hiding your mobile number Most networks allow the Caller Line Identity feature (CLI) i.e. showing the incoming number (ID) while receiving a call. Selecting Receiving caller ID allows you to check its availability from the network. Receiving caller ID To find out whether a network presents the ID of incoming calls: © Press p. Select Settings. @ Select GSM Services. Select Receiving caller ID. The network returns either Presentation available or Presen- tation unavailable. © Press Exit /-\ or \S/ to return to the stand-by display. To hide your number, on a call by call basis, add #31# before the number you are calling. Alternatively you can ask your service operator to always disable the sending of your mobile number. In this case to reveal your number, on a call by call basis, add *31# before the number you wish to call. Standard network setting To reset the standard network setting for sending your mobile ID: © Press p. Select Settings.

Select GSM Services. Select Sending my ID. Select My settings. Select Preset. The phone resets to the network setting agreed with your service provider. Press Exit /=\ or (3) to return to the stand-by display. Hiding or showing your number Press p. Select Settings. Select GSM Services. Select Sending my ID. Select My settings. Select Hide my ID or Show my ID. or (5) to return to the stand-by display. @ 6C© GEOCC© Finding out your current ID setting Press p Select Settings. Select GSM Services. Select Sending my ID. Select Status. The phone displays your current setting, taking into account both network and phone settings. @ Press Exit /\ or (5) to return to the stand-by display. Network When turned on, the phone automatically searches for the last net- work it was registered on. If this is not available, the phone automat- ically searches and, if able and allowed, selects a network. Editing the preferred list You can change the order and names in the preferred networks list stored in your SIM by choosing from the list in your phone. This is use- ful while roaming if you know a network provider that is more eco- nomical than another. Press p. Select Settings. Select GSM Services. Select Network. Select Preferred list. A list of networks appears. Use À or w to view the list. Press Options /=\ to change it. The following items appear: Option Description Modify by lis | Displays the general list of all known networks contained in the phone in alphabetical order Modify By |Edits or enters a nelwork number (MCC MNCJ if code you know this information. Delete _ |Deletes an entry @ Press Select /-\ to confirm the selection. @ Press Exit /-\ or (5) to return to the stand-by display. Your SIM may contain a forbidden list of networks which cannot be CC© The menu GO OC®©

used. To view the forbidden list or show the home network: © Press p- Select Settings. © Select GSM Services. Select Network. @ Select either Forbidden or Home network. A list of the forbidden networks or the home network appears. @ Press Exit /-\ or (5) to return to the stand-by display. Selecting manual search To select a specific network, e.g. one which provides better coverage in your current location: Press p. Select Settings. Select GSM Services. Select Network. Select Search. Select Manual. A confirmation screen and Scanning for net- works. appears. Use A or w to select a network from the list shown Press p to confirm the selection. Requesting... followed by the name of the network appears. The phone then returns to the stand-by display. [91 You cannot delete à netuork from the fotidden is This li is automatically updated when you perform ne manual nétork selection. Selecting automatic search (normal default setting) To perform an automatic search from the preferred list: Press p. Select Settings. © Select GSM Services. Select Network. Select Search. 8 Select Automat © Press Exit /-\ or (5 to return to the stand-by display. Call barring (network service) To stop different types of calls being made and received on the phone, you need a call barring password available only from your service pro- vider. Press p Select Settings. © Select GSM Services. Select Call barring. © Select Outgoing calls or Incoming calls. Choose:

Select Meaning Outgoing _- All outgoing Bars all outgoing calls —In£nal calls Bars only all outgoing International calls — NET exe. Bars all outgog intemational calls home except to other subscribers within the users home network Incoming —_- Allincoming Bars all incoming calls —Roaming only Bars allincoming calls when noton the home network

Select the option using A or w. Press Select /-\. Select Activate. Enter the password and press OK /-\ The network confirms the selection. Press Exit /-\ or \ÿ/ to return to the stand-by display. cancel or check the status of a call bar: Press p- Select Settings. Select GSM Services. Select Call barring. Use A or w to select the bar to cancel or check the status and Press p. You must have the password to cancel a call bar. Press Exit /-\ or \z/ to return to the stand-by display. 6 ©C0-0 66 To change the password Press p. Select Settings. Select GSM Services. Select Call barring Select Change password Enter the old password once and the new password twice when prompted. The phone confirms the change. © Press Exit /-\ or (S/to return to the stand-by display.

Broadcast - cell broadcast messages (Network Service) Networks can broadcast messages to all GSM users that can give informa- tion about local area dialling codes, weather reports, traffic news etc. You can decide what type of information to receive by choosing the corre- sponding number. You can program to receive up to 5 different types of messages. You can select from a list of 16 standard message types. New message types can be programmed into the selection list using the 3 digit cell broadcast type number. Contact our service provider for more details. Enter at least one message type into the selection list or you cannot acti- vate the service. To enter a message type in the selection list You can enter up to 5 different message types Press p: Select Settings. Select Broadcast. Select Message types. Press Options /-\. Select Modify by list (or Modify by code if type number is known). Scroll to the message type required. Press Select /-\ to validate your selection. The display confirms your choice. Press Options /=\ again to select more message types from the list, enter a message type number if known, or delete a message type. © Press Exit @ & 600€ or (3/ to return to the stand-by display. The menu

To turn on or off the broadcast service © Press p. Select Settings. @ Select Broadcast. @ Select On/0ff. @ Select On or Off. © Press Exit /—\ or (3) to return to the stand-by display. Reading broadcast messages Broadcast messages appear in the stand-by display only. The phone suppresses them during conversation or menu operation. À message can be up to 93 characters in length and cover several pages. Pages scroll automatically about every five seconds. To scroll down, press w. Options during message display Press on Exit /=\ to clear the message currently displayed. Press {4 to dial the number displayed in the message. Pressing Options /-\ displays the following menu: Option Action Delete | Delete the current message Delete AIT | Delete all messages stored in the queue Display all phone numbers found in the mes- Numbers | sage text. This allows dialling or storing them in the scratchpad if required Broadcast Off | Turns off cell broadcast Turning the broadcast alert tone on or off To turn on or off the alert tone the phone gives when a broadcast mes- sage arrives: Press p. Select Settings. © Select Broadcast. © Select Alert. @ Select On or Off. © Press Exit /_\ or (3) to return to the stand-by display. Deleting or editing a message type from the list To delete or edit a message type: © Press p- Select Settings. @ Select Broadcast. © Select Message types. Press Options /=\. @ Select Delete, Edit or Get from list. © Press Exit /-\ or (5/ to return to the stand-by display. Broadcast language To select the broadcast language: © Press p: Select Settings. © Select Broadcast. © Select Language.

Use À or w to select a language from the displayed list: Press p to validate. © Press Exit /-\ or (5) to return to the stand-by display. Using the office tools The Office Tools menu contains a scratchpad, an alarm clock, an auto-switch fea- ture and a calculator. Scratchpad You can store up to 5 separate entries of 36 characters in the scratchpad. © Press p. Select Office Tools. @ Select Scratchpad © Select Read. Use A or w to scroll through the entries. Select Write to make a new scratchpad entry. Press Options /-\ when reading entries to access the following menu: Rem Action Store Save a number to the phone book Edit Modify an entry Delete | Delete an entry Delete all — | Delete all entries Call CalTthe number displayed in the entry Alarm clock To set a daily 'Reminder Alarm“: © Press p. Select Office Tools. © Select Alarm clock. © Select On and enter the alarm time (in 24 hour format) or press OK /-\ to accept the displayed time. Confirmation appears. © Press Exit /-\ or \5) to return to the stand-by display. à appears. [91 When'on‘ he alarm acivates at te same time ever day until tumed of. The alarms sounds for up to 1 minute. Alarm clock and a vibrating bell symbol appear with the current time and the softkeys, Valid. \ and No ring /\. During a call, the alarm also sounds. To stop the alarm: Press Valid. /=\. To use as a Reminder or Snooze Alarm: Press No ring /-\, or any other key (except Valid. /=\) to stop the alarm. The alarm icons remain in the display and the alarm rings again 3 min- utes later. You can repeat the snooze for up to 15 minutes, after which the phone re- turns to its previous state, either off or on stand-by. To turn off the alarm © Press p. Select Office Tools. The menu

© Sclect Alarm clock. Select Off. Confirmation appears. pp« Press Exit /=\ or (5 to return to the stand-by display. &) y Caution - Please remember to turn off the alarm feature when board- ing an aircraft where the use of a mobile phone is not permitted and is illegal. Altematively, you can remove the battery after turning off the phone. See the General safety warnings on page 6. Auto-sWitch You can set your phone to switch on and off automatically. Turning it off helps to conserve battery life. Please note that during auto-switch on, you must re-enter your PIN code. The phone does not go into power saving mode until you enter your code. To activate the auto-switch: Press p- Select Office Tools. Select Auto-switch. Select Auto-switch-on. Select On. Enter the time you want the phone to turn on and press OK / Confirmation appears. Select Auto-switch-off. Select On. Enter the time you want the phone to turn off and press OK /\. Press Exit /-\ or (5) to return to the stand-by display. The & icon appears in the stand-by display. To turn off the auto-switch: Press p. Select Office Tools. Select Auto-switch. Select Auto-switch-on. Select Off. Stored appears. Select Auto-switch-off. Select Off. Stored appears. Press Exit /=\ or (5) to return to the stand-by display. C60G G6C00® CGCCCE® Calculator To access and use the calculator: Press p. Select Office Tools. Select Calculator. Enter a number and press @ several times to choose +, -, * or /. Enter the second number and either repeat step © or select = /-\to compute. Select Clear /-\ to correct any mistakes or clear the display. Press (5J to return to the stand-by display. 600€

Games The availability and appearance of the games depends on your network operator. There are at least two games in the phone: Reshape and Push. Game instructions appear when you select the game. Select sound effects from the menu item Options. To select a game: © Press p: Select Games. @ Choose the game and press Select /-\ or p. © Select Help for instructions and controls. © f you have already played the game and reached a certain skill level, select Code to enter and play the game at that level. © Select Play to start the game. Reshape and Push have skill levels. When you win a level, you go to the next level. After successfully playing X' number of levels the game gives you a code to enable you to re-enter the game at your previously attained skill level. The game can record player names and scores. If you receive à call while playing, answer in the normal way. The game resumes when the call finishes. To exit from the games menu press Exit /\ or press (2 to re- turn to the stand-by display. Currency-converter To use the converter, set the currencies and the exchange rate: Press p. Select Currency. @ Select Settings. © Enter the first currency name (e.g. Dollar). Press OK Enter the second currency name (e.g. Yen). Press OK /-\. (51 The menu Enter the exchange rate using @ to enter a comma. Press OK /-\ to validate the entry. Press Exit /-\ or \z/ to return to the stand-by display. [V1 To use your Qureny-converter as à Euro converter for patidipating currencis in the European Monetry Union (“Éuoländ urendes‘} lee enter te complee Euro exchange rate in Six Sigifiantfiures. For example: 1 Euro = € 0.61871 To calculate the conversion between the chosen currencies: Press p. Select Currency. Select one of the two first options. In our example: either Dollar->Yen or Yen->Dollar. @ Enter the amount to be converted. Press @ to insert a comma, if needed. Press OK /-\. The converted amount appears. @ Press Exit /-\ or (5/ to return to the stand-by display. [V1 Cnvession from one Euraland currency to another, or to non-Euroland curendes, nomall follows “tiangulton rues (2. comvesion of local eurent Euro and then Euro oter local cu ren. Your Gurency- converter does not provide this possibil, Acordingl, our result is only à dose appraimation

Internet/Wireless Application Protocol (WAP'") ARS Your phone has an WAP” internet browser to access services, such as stock buying, news, sports, weather, TV listings etc., supplied by your operator and/or your inter- net provider. The types of services offered depend on the internet provid- er and network operator. You must have à DATA subscription to access these services. Either your phone is pre-programmed with the settings or you must enter them. See below to enter the settings. If you cannot access the settings, they are pre-pro- grammed. [1 Access te connection setings depend upon heter he setigs have been pr programme prior tn Shipment from th facory. I some cases and to avoid ecrs these seing are locked' and are not user programmable Configuring General Packet Radio Service (GPRS) access points* To use the faster speed packed data service (higher data rate than GSM) you must configure at least one GPRS access point. Îf you just use circuit switching skip this procedure. If you use both packet and circuit perform this procedure. You can configure up to 10 access points. [V1 Forfuther information about GPRS, the services avallable and the charges, please contact your senice provider. To configure one GPRS access point: Press p. Select Internet. Select Settings. Select GPRS access points *. Select an empty profile ([.]) and press New /-\. Enter the Alias name and press OK /-\. Enter the Full name and press OK /- Enter the Login name and press OK /\. Enter the Login password and press OK /-\. Storing/editing connection settings (operator provided) You can enter up to 5 different profiles. To enter and store the profile details: © Press p. Select Internet. @ Select Profile list. © Select an empty profile ([..]) and press Options /-\. @ Select Edit. Enter the 4 digit phone lock code (default code 0000) and press Ok/-\ © Enter the Proxy name and press OK /\. Select the connection mode (Circuit, Packets or Circuit-packets). 600®© # The ali of GPRS depends on your mob phone model and on oursubscipon

Depending on your choice of connection mode, the questions that follow vary. Follow the column that corresponds to your choice, entering or se- lecting and confirming with OK /=\ or Select /=\: Circuit Packets Circuit+Packets Phone number Access point Access Point Analog ornumeric [IP address Phone number 9600 or 14400 Home page: http;/ | Analog or numeric Login name Activate security 9600 or 14400 Login password - Login name IP address - Login password Home page: http |- IP address Activate security - Home page: http} = = Activate security © To activate the required profile, use A or w to select it from the displayed list. Press Options /-\ and select Select to validate. © Press Exit /-\ or (3) to return to the stand-by display. [9 1 You can lo access te ntemet menu direct by pressing te nteetsfkey rom the stand by display {provided you have not persanalised te let softkey)

2. Ie phone number, login names and passtord, Home page hip address and P adress are

not redefned, get tese from your nebork operator and or inteme provider. Personalising your connection settings Optimise the behaviour of your phone while connected to the internet with the following settings: © Press p: Select Internet. @ Select Settings. © Scroll to the following items and turn on or off as required: The menu Option Action Clears the memory used to store information that Clear cache | you downloaded. To clear this memory, select the Yes option. Download | Select the Off option to reject picture downioading, pictures | This decreases the page downloading time. Used to allow or forbid the execution of scripts with- Scriptin. Pting Jin a page. Disconnects the mobile from the internet after a set Auto- period of inactivity for packets or circuit connections. disconnect | Enter the period (0 - 60 minutes) and press OK / 0 deactivates the auto-disconnect function.

Option Action Choose your preferred connection circuit or packets. your preferred connection is not available, the phone asks to use the other bearer. Preferred bearer Choose the GPRS access point you want used first. At GPRS access | least one must be defined if you choose packet bear- points * | er. The access point is operator specific. When roam- ing you must change the access point. @ Press Exit; or (5) to return to the stand-by display. Going online To go online: Press p. Select Internet. Select Home page. © Connecting to followed by your proxy name appears. Then the word Loading. (of the home page) appears. Once connected, your provider specific menu options appear. The & icon indicates a live’ circuit connection. The &f icon indicates a GPRS* connec- tion. By default the connection is not secure. To have a secure connection, set Security on” (see page 54). The +8 icon indicates a 'live' secure circuit connection. The Æf icon indicates a secure GPRS* connection. Using (y while online Press (+ while online presents the following options: Item Action Back Returns to the previous page Zoom +7- Increases or decreases the displayed text size Add bookmarks | _Adds a current card to the list of bookmarks Go to bookmarks Goes 0 a bookmark Reload Reloads the current page Home page Reloads the home page Other Site Enter a different site 5 Disconnects the browser from the network but Disconnect leaves the current page locally active Close session Disconnects the phone from the internet The appearance of these items depends on the operator and/or values in the Settings menu. Ending the online connection To end the online connection: Press (5). [5/1 You cn lo salt ose session tem under the opons menu # Te altlty of GPS depends an your mob phone model and on oursubscipton

Creating bookmarks To revisit specific cards more quickly, use bookmarks to store the card ad- dress. This function depends on your provider. You can create a maximum of 10 bookmarks. Create bookmarks from the stand-by display or while viewing a page. Directly from the stand-by display: © Press p. Select Internet. @ Select Bookmarks. ® Press Options /-,, select Modify and enter the following: Option Action Alias Name you wish to give to your bookmark Address Home page address @ Press OK/\ to validate each entry. © Press Exit /\ or (3) to return to the stand-by display. During a live connection while viewing page: © Press | to display the options menu. © Select Add bookmark, enter the Alias name and press OK /-\. [91 Bookmarks can only be Edited or Deleted from the Bookmarks item under the Intemet menu pions ile ofine. Using bookmarks Bookmarks can be used from the stand-by display or while browsing + Directly from the stand-by display: © Press p. Select Internet. @ Select Bookmarks. © Select the bookmark name you require. [V1 To access the Intemet direct use the Internet sotkey [if not personalised) + While browsing the internet: © Press |: to display the options menu. @ Select Go to bookmarks. © Select the bookmark name you require. Other site You can enter another internet address directly by using the Other site option from the Internet menu. Addresses are not stored and must be en- tered each time. GSM man machine interface codes The phone supports the standard GSM key sequences using the * and # characters sent directly from the keypad to the network. These sequences are used to activate all the supplementary services provided by the network. Consult your service pro- vider for a complete list. The menu

Accessories Using the headset Connecting the headset Insert the headset plug in the phone headset connector as shown below. [4 Mile insering the hesdset plugin the phone head onnetor make sure he Tu logo LU I'appeas on op. ben the heat ds not ok proper Using the headset Place the headset earpiece in your ear. The headset microphone Earpiece is then at a convenient level for operation Microphone You can answer, reject and end calls using y or (see page 9). ljust the earpiece volume level using a or

Disconnecting the headset Tilt the headset plug down as shown below.

Changing the front cover (for Aura and Odyssey only) Before changing the cover always switch off the phone and disconnect from any charging device or car kit. Removing the cover Remove the front cover as shown below. Replacing the cover Replace the front cover as shown below. Hook slots [YA Do no use umecessay force uen changing the cor. nid excessive ending. Aod remong and rplang te fat cover to oflen: ti can meaken he ont ve ook and dis, Do not leave in direct sunlight. Aays use the phone vith the cover attached Do not clean the phone andor font over ni aehl, stong chemical or sons pet nl with sf. sigty dampened dat Read te Gare and maimenanceinstuins, page 13 Accessories

Appendix Glossary Expression AC/DC charger Alternating Current/Direct Current charger Active call The call currently in conversation ALS Alternate Line (Line 2) Service AoC Advise of Charge - subscription service APN GPRS Access Point Name c Cell Broadcast cu Caller Line Identity - displays callers telephone number Conversation mode When the phone is making or receiving a call DES Data Encryption standard Diverting Diverts incoming calls to the phone to another number DTC Desk Top Charger DTMF Dual Tone Multifrequency Tones FDN Fixed Dialling Number GPRS General Packet Radio Service Gsm Global System for Mobile communications http HyperText Transfer Protocol IN Information Numbers of your operator D Internet Protocol LCD Liquid Crystal Display MMI Man machine Interface PIN/PIN2 Personal Identification Number. Supplied by your net- work/service provider

PPP Point to Point Protocol PUK/PUK2 PIN Unblocking Key. Used to unlock PIN and PIN2. Sup- plied by your network/service provider Roaming (Rm) The ability to use your telephone at home or abroad SON Service Dialling Number. Of your operator or service provider SIM Subscriber Identity Module. Supplied by your network/ service provider sms Short Message Service SPN Service Provider Name SR Status Report - relates to SMS messages Stand-by mode When the phone is on, registered onto a network but not making or receiving a call URL Uniform Resource Locator WAE Wireless Application Environment WAP" Wireless Application Protocol WSP Wireless Session Protocol WTP Wireless Transport Protocol Appendix

Trouble shooting Problem Possible cause and solution Phone will not switch

Check that the battery is fully charged and correctly connected to the phone. No flashing battery icon There may be no mains supply. Try a different electrical socket. The AC/DC charger may be faulty. Return to your dealer and try substitution with another Mitsubishi adaptor. If faulty contact your dealer. Short stand-by and talk times Cell broadcast is permanently on, using more battery power. Phone is in a poor signal area and therefore always on full power incorrect charging and discharging. Always charge and discharge your battery fully. The battery is wearing out. Replace the battery. Calls cannot be made or received Check that you have at least one signal strength bar (nt). Try in a stronger signal strength area. If the name of a network is not displayed, check your SIM is OK, check registration with your network/service provider. Call barring option is turned on. Turn it off (see page 48). Call cost limit is reached (see page 35). Stored telephone num- bers cannot be recalled Fixed Dialled Number or Call Barring features are turned on. Check features and turn them off (see pages 28 and 48) Numbers cannot be en- tered in the display Keypad lock is on ( & appears). Press Unlock /= and @ to turn off. Phone switches on but there is no display Display contrast is turned down too low. Reset contrast (see page 39). Battery icon mm not flashing 1-2-3 during charging Indicates a charging or battery problem. Turn off and disconnect the charger. Reconnect and try again If the problem remains contact your dealer. Flashing & Thereis not enough memory to store another SMS mes- sage. You must delete one or more of the existing stored messages (see page 29) -) softkey Function no longer available in the SIM or was subscrip- tion dependent. Reprogram the softkey (see page 40).

Error messages Problem Possible cause and solution Allowed credit You are trying to place an outgoing call and the allowed reached! credit is already reached. The allowed credit limit is reached during an outgoing call (the call is then aborted). Busy You are trying to make a call and the call fails because the destination number is already engaged in conversation. Call failed The user is unreachable. The outgoing call fails due to: the network cannot take the call due to system busy or the number is out of order or the number is unreachable or the network does not answer or the option to hide your phone number when calling is not supported by the network Control the ability to hide your ID when making a call (service availability in network). Cancelled. No type se- lected Cell broadcast activation has been requested but no message type has been selected Cannot execute com- mand You have made a request which is impossible to be ex- ecuted in the current call situation. Can't display message The short message text cannot be displayed (characters not recognised, incorrect format etc.) Check SIM! There is no SIM present or the SIM is incorrectly insert- ed. See page 8 for more details. Check your password You changed the call barring password or You changed the call barring service status. The entered password seems to be wrong or incorrect. Check your request You made a request for a service that seems to be im- possible to fulfil. Check your subscrip- | You tried to activate a GSM service. You are requested tion to check your subscription regarding the related service rights of use/access. Error! The network cannot perform your request and gener- ates an error result. Appendix

Failed An SMS sending process failed (the short message can- not be sent). Incorrect entry You entered a character string with a syntax error. Invalid number You tried to make a call and the call is rejected by the network because the network does not recognise the phone number structure or you tried to store a phone number that is too long to be stored in the selected location or you tried to move a phone entry to a location that is un- able to receive the phone number (phone number too long) Keypad locked “Unlock" # to unlock A press on any key is made with keypad locked Low battery! This text appears when the battery becomes t00 low and the mobile soon switches off automatically. Network busy You tried to make a call. The call is rejected by the net- work due to congestion problems. Network not allowed When selecting network manual search, you have se- lected a network that rejects the connection. New PIN incorrect. Try again Changing PIN: the new PIN code values differ (value control). New PIN2 incorrect, Try again Changing PIN2: the new PIN2 code values differ (value control). No action performed When a copy/move operation is made on memories but no conditions have been changed (same memory, number and name) No response You made a call to a remote user and no response has been received. Not allowed Your number/character entry is not allowed. Not allowed A call is tried, but cancelled due to fixed dialling control (fixed ing) {the number dialled does not match with one of the fixed dialling numbers in memory) Not Available There is no more SIM storage. Number changed The called number has changed. PIN blocked A wrong PIN code has been entered 3 times. PIN2 blocked A wrong PIN2 code has been entered 3 times.

PUK2 blocked À wrong PUK code has been entered 10 times. The SIM services protected by the PIN2 code have now been permanently disabled. Reaching allowed credi The cost limit is about to be reached. The connected call ends automatically when the limit is reached. Ring volume Off The ring volume is set to 0 (no volume). Service not available Activating some GSM services that are not available on the network SIM blocked. Contact provider À wrong PUK has been entered 10 times. The SIM card has been permanently disabled and needs to be replaced by a new one SIM blocked. Enter PUK: A wrong PIN code has been entered 3 times. Enter the PUK code to unblock the SIM card. SIM fixed full SIM names full Phone names full The corresponding memory is full. SMS memory locations are full The storage of new messages (when writing a new SMS) is impossible. Wrong code. Try again A wrong phone lock code has been entered. Wrong new code. Try again The new phone lock codes do not match (value control). Wrong PIN, try again Wrong PIN2, try again Wrong PUK, try again Wrong PUK2, try again The wrong code has been entered. Appendix

Guarantee Pan European Service Hf you require service, then in the first instance, you should contact your supplier. Should you experience any difficulty then please contact your nearest MITSUBISHI location listed below for information on other service centres UNITED KINGDOM ESPAñA BELGIUM Tel: [phone] Tel: [phone] Tel: [phone]

Tel: [phone] Tel: [phone] Tel: [phone]

Tel: [phone] Tel: [phone] Tel: [phone] To obtain Warranty Service, you will require your original equipment purchase invoice or irrefutable proof of purchase. Please see warranty terms and conditions for in warranty service. Pan-european GSM End-user Guarantee Conditions 1.You can benefit from this guarantee only if yeu are the original end-user purchaser. 2.MITSUBISHI guarantees that for à period of twelve (12) months from the date of purchase from your dealer, the Product shall be free from defects in materials and workmanship. Subject to the conditions below, Mitsubishi will indemnify you against all cost of parts and labour for repairs to or replacement of the product or parts (which may include equip- ment of similar type) where conducted by an authorised MITSUBISHI GSM service centre. MITSUBISHI shall be entitled to retain product which has been replaced. Any claims must be made to an authorised MITSUBISHI GSM service centre in the countries mentioned in the service card enclosed with the product. n case of difficulty you can con- tact the Mitsubishi companies listed in the service card to obtain details of your nearest authorised MITSUBISHI GSM service centre. As a condition of this guarantee, the date of your purchase must be confirmed by producing your original invoice from your supplier or your sales receipt, showing the serial number, together with the service card. Final de- termination of guarantee claim eligibility shall be made by MITSUBISHI. MITSUBISHI shall not be liable for shipment costs to and from an authorised GSM MITSUBISHI service cen- tre; the product travels at your risk. A.This guarantee does not cover a)battery defects of any nature; binon-compliance with directions for use; dinstallation or removal charges where the product is installed in a vehicle didefects or failures caused by accident, misuse, improper installation or improper repair by an unauthorized repairer, alteration or modification, neglect, failure to use for nor- mal purpose, Acts of God, water ingress, use in adverse environmental conditions (hu- midity or temperature); e)cost of or performance of modifications to product to adapt or adjust to conform to national or local safety laws, where such safety laws go beyond harmonised European Union standards; loss of use of the product or consequential loss of any nature; g)loss of use of air-time, loss of use of any loaned equipment or ancillary equipment; Hiprovision of incorrect or insufficient signal on air-time network, upgrading of product software to changes in network operating parameters, mains supply voltage fluctua- tions, incorrect SIM card (memory card) parameters for connection to airtime retailer; damage caused by non-MITSUBISHI accessories. 5.Any guarantee claim or service does not extend the original guarantee period unless so required by prevailing national law. 6.This guarantee is valid only if the product is purchased and used in the European Union, Norway, Iceland or Switzerland THIS GUARANTEE DOES NOT AFFECT YOUR STATUTORY RIGHTS.

Name ï Electric Telecom Europe S.A. RCS Nanterre B 307 593 129 Address 25, boulevard des Bouvets Town Nanterre Cedex Postal code 92741 lntification of the product Nature Mobile Cell Telephone Type Dual band GSM 900/DCS 1800 Sales reference MT-060 Other information Identification of the notified organization Name Autorité de Régulation des Télécommunicat Identification number : 0165 Procedure followed Annex HI of the directive 1999/5/CE Declares under its entire responsibility that the product described above complies with the following basic applicable requirements (and in particular those in the 1999/S/CE directive): Article 3.1a: (health protection and user safety)

Article 3.1b: (protection requirements concerning electromagnetic compatibility)

89/336/CEE, ETS 300 342-1

Article 3.2: (proper use of the radio-electric spectrum so as to avoid damaging interference) EN 301 511 To this effect, declares that all the radio test series have been carried out. 6 June 2001,

Viet Mailam Managing Director Declaration of compliance

Name Mitsubishi Electric Telecom Europe S.A. RCS Nanterre B 307 593 129 Address 25, boulevard des Bouvets Town Nanterre Cedex Postal code 92741 dentification of the product Nature Mobile Cell Telephone Type Dual band GSM 900/DCS 1800 Sales reference MT-160 Other information Identification of the notified organization Name Autorité de Régulation des Télécommunications (ART) Identification number : 0165 Procedure followed Annex HI of the directive 1999/S/CE Declares under its entire responsibility that the product described above complies with the following basic applicable requirements (and in particular those in the 1999/S/CE directive): Article 3.1a: (health protection and user safety)

Article 3.1b: (protection requirements concerning electromagnetic compatibility)

89/336/CEE, ETS 300 342-1

Article 3.2: (proper use ofthe radio-electric spectrum so as to avoid damaging interference) EN 301 511 To this effect, declares that all the radio test series have been carried out. 6 June 2001,

Viet Mailam Managing Director

Name ï Electric Telecom Europe S.A. RCS Nanterre B 307 593 129 Address 25, boulevard des Bouvets Town Nanterre Cedex Postal code 92741 lntification of the product Nature Mobile Cell Telephone Type Dual band GSM 900/DCS 1800 Sales reference MT-260 Other information Identification of the notified organization Name Autorité de Régulation des Télécommunicat Identification number : 0165 Procedure followed Annex HI of the directive 1999/5/CE Declares under its entire responsibility that the product described above complies with the following basic applicable requirements (and in particular those in the 1999/S/CE directive): Article 3.1a: (health protection and user safety)

Article 3.1b: (protection requirements concerning electromagnetic compatibility)

89/336/CEE, ETS 300 342-1

Article 3.2: (proper use of the radio-electric spectrum so as to avoid damaging interference) EN 301 511 To this effect, declares that all the radio test series have been carried out. 6 June 2001,

Viet Mailam Managing Director Declaration of compliance

Unanswered call Voice mail Battery Alarm volume Charging Disposal Fitting Low battery waming Removing Safety information Use Battery cover Replacing Bookmarks Creating Deleting Using Broadcast Alert Language Message types ovoff Cache memory Cearing Calculator call Conference Duration Holding Muïti-party Reminder Retrieving Times Waiting Cal barring Password

Gall costs Line selection Call Log Care and maintenance CB messages Deleting Editing Reading Cell broadeast Conference call Connection profile Cost management Cover changing removing Replacing Creating a draft text Credit limit Currency-converter

Date setting Default settings Dialling Calls Log memory Phonebook Dialing from memory Display contrast Diverting Draft text Creating Editing DTMF tones Emergency calls Ending a call Entering text Error messages

Mobile number Hiding Showing Muiti-party cal Muting

Network Network services