BERLIN - Baby bed HAUCK - Free user manual and instructions
Find the device manual for free BERLIN HAUCK in PDF.
User questions about BERLIN HAUCK
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Baby bed in PDF format for free! Find your manual BERLIN - HAUCK and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. BERLIN by HAUCK.
USER MANUAL BERLIN HAUCK
- Never leave your child unsupervised.
- All fittings must be properly fastened at all times. Screws must not be loose, as children can become stuck on them or items of clothing (e.g. cords, necklaces, and dummy chains) can get caught up on them, and then there is a risk of strangulation.
- Never leave anything in the cot that your child can use to climb up.
- Never leave anything in the cot that can pose a risk of your child suffocating or being strangled.
- Never put the cot with your child in it near fans, fires, sources of heat, electrical equipment, sharp edges, dangling curtain cords, ties, ribbons or water tanks. These pose a risk of injury.
- The lowest position of the cot base is the safest. If your child is old enough to sit up, put the cot in the lowest position to ensure maximum security.
- We recommend that you use a mattress measuring 695mm× 1,375 mm.
- The height of the mattress must be such that the height to be climbed over (surface of the mattress to top edge of the cot frame) is at least 500mm in the lowest position of the cot base and at least 200mm in the highest position.
THIS COT COMPLIES WITH STANDARD
716-1:1995-12, 716-2:1995-8
List of parts:
A Top part of head/foot of the cot 2×
B Bottom part of head/foot of the cot 2x
C Slatted frame 1x
D1 Side panel 1x
D2 Side panel with three sliding bars 1x
E Allen screw 12x
F Gudgeon 12x
G Metal pins 4x
H Caps 8x
I Allen key 1x
How to assemble the cot:
Insert the metal pins (I) into the bottom part of the head/foot, then join the top part of the head/foot (A) to the bottom part of the head/foot (B).
Insert the gudgeons (F) into the slatted frame (C) and screw the screws (E) on to the head/foot using the Allen key (I). Do the same with the side panels (D1 and D2).
Use the caps (H) to seal off the openings.
Locate three sliding bars in the middle of side panel D2 (see marking). These can be removed by pressing upwards.
Sliding bar
How to assemble the head and foot
Cot
How to assemble / Convert the cot to a child's bed:
To convert the cot into a child's bed, loosen the screws on the side panels (D1 and D2) and the slatted frame (C) and remove the head/foot (B). Next, join the top parts of the head/foot to the slatted frame (C), tighten the screws and you child's bed is ready to use. Seal off the drill holes with the caps (H).
Care instructions
The cot requires no maintenance. However, check the bed for worn-out parts from time to time and replace them immediately.
To clean the cot, please use a damp cloth and mild detergent.
F
Précautions :
DIT BED VOLDOET AAN DE NORM
716-1:1995-12, 716-2:1995-8
Onderdelenlijst :
IMPORTANT - KEEP IT FOR LATER READING
CONSERVER CE MODE D'EMPLOI POUR UN
USAGE ULTERIEUR ET LE LIRE ATTENTIVEMENT
BELANGRIJK - BEWAAR ALS NASLAGWERK
TUV Thuringen
hauck GmbH & Co KG
Tel. : +49 (0)9562 / 986-0
Frohnlacher Str. 8
Fax. : +49 (0)9562 / 6272
D-96242 Sonnefeld
Email : info@hauck.de
Germany
Internet: http://www.hauck.de
