MECABLITZ 48 AF-1 PENTAX - External Flash METZ - Free user manual and instructions

Product Type	External flash
Brand	METZ
Model	MECABLITZ 48 AF-1 PENTAX
Dimensions (H x W x D)	71 x 137 x 99 mm
Weight	Approx. 425 g
Power Supply	4 batteries/rechargeable AA (NiCd, NiMH, alkaline, lithium)
Guide Number max (ISO 100, 105 mm)	48 (meters)
Flash Modes	TTL, P-TTL, P-TTL HSS, Manual (M)
Motorized Zoom Range	24 - 105 mm (with wide-angle diffuser: 18 mm)
Recycling Time (full power)	Approx. 3.5 s
Number of Flashes (full power)	90 to 460 depending on batteries
Color Temperature	5600 K
ISO Sensitivity	6 to 6400
Synchronization	1st curtain, 2nd curtain (REAR), high speed (HSS), slow speed (SLOW)
Special Functions	Wireless slave, EV correction, bracketing (FB), modeling light, extended zoom, contrast control
AF Illuminator	Yes, range 6-9 m
Head Tilt/Swivel	Vertical: -7° to 90°; Horizontal: left/right 30° to 180°
Firmware Update	Via USB port
Maintenance and Cleaning	Soft dry or silicone cloth; no detergent
Safety Instructions	Do not trigger near eyes, flammable gases; internal high voltage; do not open
Optional Accessories	Mecabounce 58-90, reflector screen 58-23, flash stand W-F127

Frequently Asked Questions - MECABLITZ 48 AF-1 PENTAX METZ

How do I mount the MECABLITZ 48 AF-1 flash on the camera?

Turn off the camera and flash. Turn the locking wheel towards the flash, slide the foot into the hot shoe, then turn the wheel towards the camera to lock. To remove, reverse the process.

What type of batteries should I use?

Use 4 AA batteries: alkaline, lithium, NiCd or NiMH. Observe polarity. Always replace with a full identical set. Remove batteries if not used for a long time.

Why doesn't the ready indicator light up?

Is the recycling time over 60 seconds? The batteries may be exhausted. Replace them. Also check that the main switch is ON.

How do I use the wireless slave mode?

Activate remote slave mode (SL) via the Select menu. Set the same channel (CH1-4) as the master flash. Place the slave flash on a stand and ensure it receives light from the master.

What if the flash does not synchronize in high-speed sync (HSS)?

Set the flash to P-TTL HSS mode using the Mode button. The camera must support high-speed sync and use a shutter speed shorter than normal sync. Range will be reduced.

How do I clean the flash?

Use a soft, dry or slightly silicone cloth. Never use detergent, as it may damage the plastic.

The AF illuminator does not activate, why?

Check that the flash is ready (indicator on), the camera is in single autofocus mode (S-AF), and the center AF sensor is selected. Some compact cameras use only their own AF.

How do I reset the flash to factory settings?

Hold the Mode button for about 5 seconds until 'rES' appears. The reset does not remove firmware updates.

What if the display shows abnormal values?

Turn off the flash for 10 seconds, check camera settings and that the foot is properly inserted. Replace batteries if necessary. If the problem persists, contact your dealer.

How do I use the wide-angle diffuser?

Pull the wide-angle diffuser forward until it clicks, it folds down automatically. The flash sets zoom to 18 mm. To store, lift it and push it back in fully.

USER MANUAL MECABLITZ 48 AF-1 PENTAX METZ

Black Motz 48 AF-1 digital flash unit with visible lens and control buttons (no text beyond branding)

MECABLITZ 48 AF-1 digital

für/for Pentax-/Samsung SLR-Digitalkameras mit/with P-TTL / TTL

Bedienungsanleitung

Gebruiksaanwijzing

Manuale istruzioni

Mode d'emploi

Operating instruction

Abmaße in mm (B x H x T):

Ca. 71 x 137 x 99

Gewicht :

Ca. 425 g

7.4 Mode spot beam "Sb" 32

7.4 Mode spot beam "Sb"

10.1 Indirect flitsen .....61

[↓] Knippert langzaam

1 Safety instructions ....69

2 Dedicated flash functions .....70

3 Preparing the flash unit for use .....70

3.1 Mounting the flash unit .70

3.2 Power supply ....70

3.3 Switching the flash unit on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

3.4 Auto OFF for the flash unit .....71

4 LED displays on the flash unit .....72

4.1 Flash readiness indication .....72

4.2 Correct exposure indication .....72

5 Information in Display 72

5.1 Display of the flash mode .....72

5.2 Range display .....72

6 Displays in the camera viewfinder .....73

6.1 Flash-ready indicator .....73

6.2 Exposure control indicator in TTL flash mode .....73

6.3 Warning indicator .....73

9.9 Shooting format adjustment (S.Zoom) 80

9.10 Contrast (CC) 81

10 Flash techniques .....81

10.1 Bounce flash 81

10.2 Bounce flash with a reflector card .....82

10.3 Close-ups / macro shots .....82

11 Flash synchronisation ....82

11.1 Automatic flash sync speed control 82

11.2 Normal synchronisation 82

11.3 Second curtain synchronisation (REAR) 82

11.4 Slow synchronisation (SLOW) 83

12 Automatic AF measuring beam 83

13 Triggering control (auto-flash) .....83

14 Care and maintenance ....84

14.1 Firmware updates 84

14.2 Reset 84

14.3 Flash capacitor forming 84

15 Troubleshooting 84

16 Technical data ....86

17 Optional accessories ....87

Table 1: Guide numbers at maximum light output (P 1/1) .....131

Table 2: Flash durations at the individual partial light output levels .....132

Table 3: Recycling times and number of flashes with different battery types .133

Table 4: Maximum guide numbers at HSS-Mode .....133

Introduction

Thank you for purchasing a Metz product. We are happy to welcome you as a customer.

Of course, you are excited to start using the flash unit right away. However, it is worthwhile reading the operating instructions first to learn how to use the flash correctly.

This flash unit is suited for:

- Analogue and digital Pentax cameras with TTL or P-TTL flash control and system flash shoe, as well as compatible digital cameras from Samsung.

This flash unit is not suited for other brands of cameras. Also take a look at the image page at the end of the manual.

1. Safety instructions

• The flash unit is intended and approved exclusively for photographic use!
• Never fire a flash in the vicinity of flammable gases or liquids (petrol, solvents, etc.)! DANGER OF EXPLOSION!
• Never take flash shots of car, bus or train drivers, or of motorcycle and bicycle riders while they are in motion. They could be blinded by the flash and cause an accident!
• Never fire a flash in the immediate vicinity of the eyes! A flash fired into the eyes of a person or animal at close range may damage the retina and lead to severe visual disorders, including blindness!
• Only use the approved power sources listed in the Operating Instructions!
• Do not expose batteries to excessive heat sources such as sunshine or fire!
• Never throw flat/dead batteries onto a fire!

• Dead batteries should be removed from the flash unit immediately, as lye leaking from dead batteries can damage the flash unit.

• Never recharge dry cell batteries!

• Do not expose the flash unit or battery charger to dripping or splashing water such as rain!
• Protect the flash unit from excessive heat and humidity! Do not store the flash unit in the glove compartment of a car.
• When a flash is fired, no opaque material may be in front of or directly on the reflector screen of the flash unit, nor may there be dirt on the reflector screen. The high heat generated by the flash can cause such material to burn or cause damage to the reflector screen.
• Do not touch the reflector screen after a series of flash shots, as you may burn yourself.
• Never disassemble the flash unit! DANGER: HIGH VOLTAGE! There are no components inside the flashgun that can be repaired by a layman.
• When taking flash shots at full light output and in rapid succession an interval of at least 10 minutes after 15 flashes must be observed!
• When taking a series of flash shots at full light output and with rapid recycling times, and with zoom positions of 35 mm and less, the diffuser heats up, due to the high level of thermal energy.
• This flash unit may be used in combination with a camera-integrated flash only if the flash can be folded out completely.
• Rapid changes in temperature may lead to condensation. If this occurs, allow time for the unit to become acclimatized.
• Never use defective batteries of any type with this flash unit.

2. Dedicated flash functions

Dedicated flash functions are flash functions that have been specially adapted to a given camera system. Depending on the type of camera, different flash functions are supported.

• Flash-ready indication in camera viewfinder/camera display
• Exposure control indication in camera viewfinder with TTL
  • Automatic flash sync speed control
• Flash bracketing „FB“
  • Automatic flash / triggering control
• Contrast control
• Spot beam mode „SB“
• TTL flash mode
• P-TTL flash mode
  • Automatic TTL-/P-TTL-fill-in flash control
• Manual flash exposure correction
• 1st or 2nd curtain synchronisation (REAR, 2nd curtain, SLOW2)
  • High-speed synchronisation (high speed flash operation) P-TTL-HSS
  • Automatic motor zoom control
  • Automatic AF measuring beam control (multi-zone AF measuring beam)
  • Automatic flash range indication
• Programmed flash mode
• Preflash function for reducing the red-eye effect
• Wireless P-TTL remote flash operation as slave flash unit
• Wake-up function for the flash unit
• Firmware update via USB connector

It is impossible to describe all camera types and their individual dedicated flash functions within the scope of these instructions. Therefore, please refer to the flash mode description in your camera's operating instructions to find out which functions are supported and which ones have to be set manually on the camera.

3 Preparing the flash unit for use

3.1 Mounting the flash unit

Mounting the flash unit on the camera

Turn off the camera and flash before mounting or removing.

• Turn the knurled nut ⑫ towards the flash unit housing as far as it will go. The locking pin in the adapter shoe is now fully retracted into the case.
• Slide the flash unit foot completely into the camera accessory shoe.
• Turn the knurled nut ⑫ towards the camera housing as far as it will go, clamping the flash unit in place. If the camera does not have a locking hole, the spring-loaded locking pin retracts into the adapter case so as not to damage the surface.

Removing the flash unit from the camera

Turn off the camera and flash before mounting or dismounting.

• Turn the knurled nut ⑫ towards the flash unit housing as far as it will go.
• Remove the flash unit from the camera's accessory shoe.

3.2 Power supply

Suitable batteries/rechargeable batteries

The flash unit can be operated with any of the following batteries:

- 4 NiCad batteries 1.2V, type IEC KR6 (size AA). They permit very fast recycling times and are economical in use because they are rechargeable.

• 4 nickel-metal-hydride batteries 1.2V, type IEC HR6 (size AA). They have a significantly higher capacity than NiCad batteries and are less harmful to the environment, since they have no cadmium.
• 4 alkaline-manganese dry cell batteries 1.5V, type IEC LR6 (size AA). Maintenance-free power source for moderate power requirements.
• 4 lithium batteries 1.5V, type IEC FR6 (size AA). Maintenance-free high-capacity power source with a low self-discharge rate.

If your flash unit is not going to be used for an extended period of time, remove the batteries.

Replacing batteries

The batteries are flat or dead if the recycling time (elapsing from the triggering of a full-power flash, e.g. in the M mode, to the moment the flash ready indicator ③ lights up again) exceeds 60 seconds.

• Turn off the flash unit at the main switch ①.
• Slide the battery compartment cover ⑨ forwards and fold open.
• Insert the batteries lengthwise as indicated by the battery symbols provided. First, insert the batteries that face the display and then the others. Close the battery cover ⑨.

When inserting batteries, ensure that the polarity is correct and matches the symbols in the battery compartment. Inserting the batteries in the wrong direction can destroy the flash unit! Always replace all batteries simultaneously, and make sure that batteries are the same brand and have the same capacity. Flat or dead batteries should not be disposed of with ordinary household waste. Help protect the environment, and dispose of flat/dead batteries at the appropriate collection points.

3.3 Switching the flash unit on and off

The flash unit can be turned on by flipping the main switch ① to the „ON“ position.

To turn off the flash unit, flip the main switch ① to the left position.

If your flash unit is not going to be used for an extended period of time, we recommend turning it off with the main switch and removing the power source (i.e., batteries).

3.4 Auto OFF for the flash unit

To save battery power and prevent inadvertent battery drain, the flash unit is factory-set to automatically switch to standby mode (Auto OFF) 10 minutes after

• being switched on,
  • after pressing a key,
• a flash is fired
  • the shutter release is actuated

- the camera's exposure metering system is switched off.

...The flash readiness indicator and the LC display are also switched off.

If the flash is manually switched on again, the last settings prior to the automatic switch off are retained and immediately available. The flash unit can be reactivated by pressing any button or by lightly depressing the shutter release (wake up function).

The flash unit should always be turned off using the main switch ① if it is not going to be used for an extended period.

If necessary, the Auto OFF function can be set to occur after 1 minute of inactivity, or can be deactivated (see 9.4).

4 LED displays on the flash unit

4.1 Flash readiness indication

When the flash capacitor is charged, the flash readiness symbol ③ lights up on the flash unit, indicating that the flash is ready to fire. This means that flash light can be used for the next shot. Flash readiness is also transmitted to the camera and indicated accordingly in the camera's viewfinder (see 6).

If a shot is taken before the flash readiness indicator appears in the camera's viewfinder, then the flash unit will not be triggered and, if the camera has already switched to flash sync speed (see 11.1), the shot may have the wrong exposure.

4.2 Correct exposure indication

The correct exposure indication „OK“ ④ only lights up for about 5 seconds if the shot was correctly exposed in TTL flash mode (TTL, PTL, PTLHSS; see 7)! If no „OK“ exposure indication appears after the shot, then the shot was under-exposed. You will need to repeat the shot with the next smaller f-number (for example, f/8 instead of f/11) or the distance to the subject or reflecting surface (for example, with bounce flash) will have to be reduced. Note the maximum flash range indicated on the display of the flash unit (see 5.2). For information on the correct exposure indicator in the camera viewfinder, also see 6)!

5 Information in Display

Most cameras transfer the values for the ISO, focal length (mm) and aperture to the flash unit. It calculates the maximum flash range from the settings and their guide number. Flash mode, range and zoom position of the main reflector are displayed in the display of the flash unit.

If the flash unit is operated without having received data from the camera, only the flash mode selected, the zoom position of the main reflector and „Zoom“ is displayed. The readout for the range occurs only once the flash unit has received the required data from the camera.

Auto-Zoom and flash range are only displayed on cameras where the aperture and ISO values are transmitted to the flash unit!

Display illumination

Every time a button on the flash unit is pressed, the flash display illumination is activated for 10 seconds. When a flash is fired via the camera or the hand release ↗ ③ on the flash unit, the display illumination is switched off.

5.1 Display of the flash mode

The current flash mode is shown in the display. Depending on the type of camera, different displays are available for the selected TTL flash mode (e.g., TTL, PITT, PTLHSS) and the manual flash mode M (see 7).

5.2 Range display

The flash range is displayed when using cameras that transmit ISO, lens focal length and aperture data. For this a data exchange must have occurred between the camera and flash unit, for example by tapping the shutter release. The range can be displayed either in metres (m) or feet (ft) - see 9.7.

The flash range is not displayed when no data is transmitted from the camera.

• when the reflector head is tilted out of its normal position (upwards, downwards or sideways).
• the flash unit is working in remote flash operation (slave SL).

Range display in TTL flash modes

In the TTL flash modes (TTL, PTTL, PTLHSS; see 7.1) the value for the maximum range of the flash unit is displayed. The value indicated relates to subjects with a reflection factor of 25%, which applies to most photographic situations. Strong deviations from this reflection factor, as in the case of highly reflective or poorly reflective subjects, may affect the flash range of the flash unit.

The subject ought to be in the area of approximately 40% to 70% of the value displayed. This will give the automatic exposure control sufficient scope for com-

pensation. To avoid overexposure, the minimum distance should be no less than 10% of the indicated value! Adjustment to the photographic situation at hand can be achieved by, for example, changing the aperture of the setting on the lens.

Range display in manual flash mode M

In manual flash mode M, the distance that must be maintained from the subject for correct flash exposure is indicated. Adjustment to the photographic situation at hand can be achieved by, for example, changing the aperture setting on the lens or selecting a manual partial light output level (see 7.2).

Exceeding the display range

The flash unit can indicate flash ranges of up to 199 m or 199 ft. This display range can be exceeded in the case of high ISO values (e.g., ISO 6400) and large aperture openings. An arrow or triangle after the distance value indicates that the display range has been exceeded.

6 Indicators in the camera viewfinder

Information is only displayed in the viewfinder if the metering system is activated, e.g. when lightly touching the shutter release. Under certain circumstances the information displayed in your camera's viewfinder may differ from those described below. More details on the indicators in the camera viewfinder can be found in the camera's operating instructions.

6.1 Flash-ready indicator

- lights up - The flash unit is flash-ready. When the camera shutter is released the flash is fired. - does not light up

The flash unit is not flash-ready. Wait until the mecablitz is flash-ready. Or in the case of a flash-ready flash unit:

the camera activates the triggering control owing to intense ambient light conditions (see chapter 13). In this case no flash is needed to take the shot!

6.2 Exposure control indicator in TTL flash mode

In the P-TTL flash mode an exposure control indicator lights up in the viewfinder for a correctly exposed shot!

flashes rapidly after the shot has been taken. The shot was correctly exposed.
goes out immediately after the shot has been taken
The shot was underexposed. Reduce the distance to the subject, select a larger aperture (= smaller f-number) or use a higher film speed. Wait until the flash-ready indicator reappears before taking the next picture.

6.3 Warning indicator

[↓] flashes slowly

Flash is needed given the current photographic situation. Signal that a flash unit needs to be used and/or that the (internal or external) flash unit should be switched on.

[⚡] flashes rapidly before the shot has been taken

The shot cannot be fully illuminated at the edges of the picture with the selected lens focal length (e.g. using a wide-angle lens 28 mm) using the integrated camera flash, because the lens focal length is less than 35 mm.

flashes rapidly before the shot has been taken

The shot cannot be fully illuminated at the edges of the picture with the selected lens focal length (e.g. wide-angle lens) and using the current reflector position of the mecablitz, for instance if the value for the reflector position (mm) is greater than the lens focal length.

For information applicable to the displays in the viewfinder of your camera model, refer to the camera's operating instructions.

Depending on the type of camera different TTL flash modes, manual flash mode and high-speed synchronisation FP or HSS are available. Therefore, data transfer between flash unit and camera is necessary before setting the flash mode, e.g. by actuating the shutter release. The flash mode is set by using the „Mode“ ② button.

7.1 TTL-flash modes

The TTL flash modes offer a very simple method of achieving very good flash shots. In these modes, exposure readings are taken by a sensor built into the camera, which measures the amount of light through the camera lens (TTL = „Through The Lens“). Here the camera automatically determines the flash performance required for a correct exposure of the shot. The advantage of the TTL flash modes is that all factors influencing exposure (filters, change of aperture and focal length with zoom objectives, extensions for close-ups, etc.) are automatically taken into account in adjusting the flash light.

If the shot was correctly lit, the correct exposure indication ④ will flash „OK“ for about 5 seconds (see 4.2).

Please note whether there are limitations for your camera in terms of film sensitivity for TTL flash mode (for example, ISO 64 to ISO 1000; see camera's operating instructions)! In analogue cameras there must be a film in the camera to test the TTL function!

P-TTL flash mode

The P-TTL flash operation is a type of digital TTL flash operation and a further development of the TTL flash operations of analogue cameras. During shooting, the flash unit emits an almost imperceptible metering preflash prior to the actual exposure. The light reflected by the metering preflash is evaluated by the camera. The camera adjusts the subsequent flash exposure to the photographic situation according to the evaluation (see the camera operating manual for more details).

Setting procedure

- Press „Mode“ until „PITL“ flashes in the display. The setting takes effect immediately. After about 5 seconds the display stops flashing and the setting is saved automatically. „PITL“ appears in the display.

TTL flash mode

This analogue flash mode is supported by older analogue cameras. It is the normal TTL flash mode (TTL flash mode without preflash).

Setting procedure

- Press „Mode“② until „ III ” flashes in the display. The setting takes effect immediately. After about 5 seconds the display stops flashing and the setting is saved automatically. „ III ” appears in the display.

The normal TTL flash mode cannot be set on cameras supporting P-TTL flash modes!

Automatic TTL and P-TTL Fill-in flash mode

The automatic TTL or P-TTL fill-in flash mode is activated by most cameras when the automatic programme P is selected and by Vari or subject programmes during daylight (see camera operating manual).

Fill-in flash mode overcomes troublesome shadows and produces a more balanced exposure between subject and background with contre-jour shots. The camera's computer-controlled metering system sets the most suitable combination of shutter speed, aperture and flash output.

Ensure that the contre-jour light source does not shine directly into the lens, as this will interfere with the camera's TTL metering system!

There is no setting or display for automatic TTL fill-in flash in the flash unit.

7.2 Manual flash mode

In the manual flash mode M, the flash unit emits the full uncontrolled amount of light if no partial light output has been selected. The specific photographic situa-

tion can be taken into account by adjusting the aperture setting or by selecting a suitable manual partial light setting. The setting area ranges from P 1/1 (maximum light output) to P 1/128. The display shows the distance at which the subject is correctly lit (see 5.2).

Setting procedure

- Press „Mode“② until „M“ flashes in the display. The setting takes effect immediately. After about 5 seconds the display stops flashing and the setting is saved automatically. „M“ appears in the display.

Manual partial light output levels

In manual flash mode M set the partial light output desired with the buttons (+) and (-). The setting takes effect immediately and is saved automatically. The distance display is adjusted to the partial light output automatically (see 5.2).

Various camera models support the manual flash mode M only in the camera mode manual M! In other camera models an error message appears in the display and the release is locked!

7.3 Automatic high-speed synchronisation (FP or HSS)

Various cameras support automatic FP high-speed synchronisation (see the camera's operating instructions). This flash mode makes it possible to use a flash unit even with shutter speeds that are faster than the flash sync speed. Interesting results may be achieved in this mode when, for example, a wide open aperture (e.g., f/2.0) is used to limit the depth of field in portrait shots taken in very bright ambient light. The flash unit supports the high-speed synchronisation in the flash modes P-TTL (P-TTL HSS).

For physical reasons, however, high-speed synchronisation significantly reduces the number and the maximum flash range. Be sure to note, therefore, the flash range on the display of the flash unit. High-speed synchronisation is activated automatically if a shutter speed faster than the flash sync speed is set on the camera, whether manually or automatically by the exposure program.

Note that in the case of high speed synchronisation the guide number of the flash unit also depends on the shutter speed. The faster the shutter speed, the lower the guide number! The high-speed synchronisation is mainly used in the camera modes "Av" and "M".

Setting procedure

- repeatedly press the „Mode“ ② button until „P TIL HSS“ flashes in the display. The setting takes effect immediately. After about 5 seconds the display stops flashing and the setting is saved automatically. „P TIL HSS“ is shown in the display. High-speed synchronisation can be deleted by repeatedly pressing the „Mode“ button until the „HSS“ symbol disappears.

Second curtain synchronisation (REAR) is automatically deactivated when the flash unit is set to high-speed synchronisation FP or HSS!

7.4 Spot-beam mode „Sb“

In the spot beam mode, the AF measuring beam can be used to focus on a subject at low ambient light level without firing a flash when the shot is taken.

There is no flash-ready indicator in spot beam mode and no exposure control indicator in the camera viewfinder. The camera is not set to its sync speed and behaves as though there were no flash unit connected.

Spot beam mode is only activated when the flash unit is switched on and is flash-ready (check the flash-ready indicator on the flash unit!).

When the camera shutter is released, no flash is fired. Please read the notes on the AF measuring beam in chapter 12.

Setting procedure

- repeatedly press the „Mode“ ② button until „Sb“ flashes in the display. The setting takes effect immediately. After about 5 seconds the display stops flashing and the setting is saved automatically. „Sb“ is shown in the display.

8 Manual flash exposure correction

The auto flash exposure mode of most cameras is adjusted to a reflection factor of 25% (the average reflection factor of flash subjects). A dark background that absorbs much of the light or a highly reflective bright background (backlit shots, for example) may result in, respectively, underexposure or overexposure of the subject.

To offset these effects, the flash exposure can be adjusted manually for the shot with a correction value. The extent of the correction depends on the contrast between the subject and background!

In P-TTL flash modes (P-TTL, P-TTL-HSS), manual flash exposure correction factors of from -3 EV (f-stops) to +3 EV (f-stops) can be adjusted on the flash unit in one-third increments.

Tip:

Dark subject against light background: positive correction factor. Light subject against dark background: negative correction factor.

Exposure correction by means of alteration of the lens aperture setting is impossible, since the camera's automatic exposure program regards the altered aperture setting as the normal working aperture setting. When setting the correction factor, the distance shown in the display can change and be adjusted to the correction factor (depending on the camera model)!

Setting procedure

• Press button (-) or (+) until „EV“ flashes. Apply the setting wished with the buttons (+) and (-):
  Set a negative correction factor with the button (-) or a positive one with the button (+). The setting takes effect immediately. After about 5 seconds the display stops flashing and the setting is saved automatically. After saving, "EV" appears in the display with the correction value.

Press the button (-) or (+) until „EV“ without a correction factor is shown. The setting takes effect immediately. After about 5 seconds the display stops flashing and the setting is saved automatically.

Manual flash exposure correction is only possible in TTL flash mode if the camera supports this function (consult the camera's operating instructions)! If the camera does not support this function, the adjusted correction will have no effect. If the camera does not support this function, no corrective value can be set on the flash unit, the corrective value remains ineffective.

For some camera models, the manual flash exposure corrections must be adjusted on the camera. If this is the case, no correction value will appear on the flash unit display.

After the shot, remember to cancel the flash exposure correction!

Depending on the camera model, various special functions are available. For this purpose, data exchange must first occur between the flash unit and camera to access and set the special functions, for example by tapping the shutter release. Accessing the individual special functions is achieved with the button „Select“, that is to say, the buttons (-) or (+) must be pressed simultaneously. The accompanying special functions and settings desired are then carried out individually with the button (-) or (+).

The setting must occur immediately after accessing the special functions since otherwise the flash unit automatically switches back to normal flash operation after a few seconds!

9.1 Motor zoom main reflector („Zoom“)

The motor zoom main reflector ⑩ of the flash unit can illuminate lens angles from 24 mm (35 mm format): Thanks to the use of the integrated wide-angle diffuser ⑧, the illumination widens to 18 mm.

Auto zoom

The zoom position of the main reflector ⑩ is automatically adjusted to the lens focal length when the flash unit is used with a camera that transmits the data related to the lens focal length. After the flash unit has been switched on, "Zoom" and the current zoom position of the main reflector ⑩ are shown in the display.

Automatic adjustment occurs for lens focal lengths from 24 mm. If a focal length of less than 24 mm is used, "24" flashes in the display as a warning that the shot cannot be completely lit.

If so desired, the position of the main reflector ⑩ can be manually adjusted in order to achieve particular lighting effects (such as spot effect etc.).

Manual zoom mode

For cameras that do not transfer any data regarding the focal length (e.g. when using a manual focus lens), the zoom position of the main reflector must be adjusted to the lens focal length. In this case auto-zoom mode is not possible! After switching on the flash unit, "Zoom" appears in the display and the current zoom position of the main reflector ⑩ appears.

Setting procedure

• Press button combination „Select“ until „Zoom“ appears flashing next to the zoom position (mm).
• Apply the setting desired with the buttons (+) and (-). The flashing display changes to „M.Zoom“ for manual zoom mode. The following zoom positions are possible for the main reflector:
  24 - 28 - 35 - 50 - 70 - 85 - 105 mm (35 mm format).
  The setting takes effect immediately. After about 5 seconds the display stops flashing and the setting is saved automatically.

When the camera transmits the lens focal length to the flash unit and a manual zoom setting results in the shot not being completely lit by the main reflector (for example, spot effect), the display of the zoom position of the main reflector flashes as a warning!

Tip:

If you do not necessarily need the full guide number and maximum flash range of the flash unit, you can leave the zoom reflector at the position for the shortest focal length of the zoom lens. This will provide full light coverage of the picture and eliminate the need to continually adjust it to the focal length of the lens.

Example:

You use a zoom lens with a focal length range of 35 mm to 105 mm. In this case, you set the position of the main reflector of the flash unit to 35 mm.

Resetting to auto-zoom

• Touch the shutter release to begin a data transfer between the flash unit and the camera.
• Press the button combination „Select“ until „M.Zoom“ appears flashing next to the zoom position (mm).
• Press the button (+) until the 105 mm position has been exceeded. The flashing display „M.Zoom“ changes to „Zoom“ (= auto-zoom mode) and the zoom position of the main reflector ⑩ is automatically adjusted to the lens focal length. The setting takes effect immediately. After about 5 seconds the display stops flashing and the setting is saved automatically.

The return from manual zoom mode to auto-zoom mode also occurs if the flash unit is switched on again with the main switch ①.

Wide-angle diffuser

With the wide angle diffuser ⑧, focal lengths of 18 mm or more can be illuminated (35 mm format).

Pull the wide-angle diffuser ⑧ out from the main reflector as far as it will go, and then release it. The wide-angle diffuser ⑧ automatically folds downwards. The main reflector ⑩ automatically moves to the required position. The distance readings and the zoom value are corrected to 18 mm on the display panel.

To insert the wide-angle diffuser ⑧, turn it upwards 90^ and push it all the way in.

Mecabounce 58-90

If the Mecabounce 58-90 (optional accessories, see 17) is fitted to the main reflector ⑩ of the flash unit, the main reflector is automatically guided to the position required. The distance data and zoom factor are corrected to 16 mm.

9.2 Remote slave flash mode (SL)

The flash unit supports Pentax is wireless P-TTL Remote System in slave flash mode. At the same time, one or more slave flash units can be remotely controlled from one master or controller flash unit on the camera (e.g. mecablitz 58 AF-1P digital).

So that multiple remote systems in the same room do not interfere with one another, there are four independent remote channels available (CH 1, 2, 3 or 4). Master, controller and slave flash units belonging to the same remote system must be set to the same remote channel. The slave flash units must be able to receive the light from the master or controller flash unit with the integrated sensors for the remote mode ⑤.

Depending on the camera model, the camera's internal flash unit can also function as master or controller flash unit. Please consult the respective camera operating instructions for further tips on setting the master or controller flash unit.

Setting procedure for remote slave flash mode

• Press the button combination „Select“ until „SL“ flashes in the display.
• Apply the setting desired with the buttons (+) and (-).
• When „On“ is displayed, the remote slave mode is activated.
• When „OFF“ is displayed, the remote slave mode is deactivated.

The setting takes effect immediately. After about 5 seconds the display stops flashing and the setting is saved automatically. After activation of the remote slave mode, "SL" appears in the display. In addition, the remote channel is shown (CH).

Setting of the remote channel

The same remote channel must be set on the slave flash unit as on the master or controller flash unit!

• With the remote slave mode activated, press the button combination „Select“ until „CH“ (= remote channel) flashes in the display.
• Apply the setting desired with the buttons (+) and (-). Selection of group 1, 2, 3 or 4 is possible.

The setting takes effect immediately. After about 5 seconds the display stops flashing and the setting is saved automatically. After activation of the remote slave mode, "SL" appears in the display. In addition, the remote channel is shown (CH).

Use flash unit mounting foot W-F127 to set up the slave flash unit. When the slave flash unit is flash-ready, the AF measuring flash also flashes ⑪.

Manual flash exposure correction in slave operation

A manual flash exposure correction of can be set from -3 to +3 stops (EV) in 1/3 increments on the slave flash unit in the remote mode (see also 8).

Setting procedure

• Press key combination "Select" repeatedly until "EV" flashes in the display.
• Using the keys (+) and (-) set the desired correction value. The setting is immediately effective and is automatically saved after approx. 5 seconds. As a reminder of the flash exposure correction value set, "EV" continues to flash in the display.

To deactivate the flash exposure correction, delete the setting of the correction value using the keys (+) and (-).

9.3 Flash bracketing series („FB“)

A series of flash exposures FB (flash bracketing) can be carried out in the TTL flash modes (P 📄, P 📄 HSS; see 7.1). A flash bracketing series consists of three successive flash shots with different flash exposure correction values:

• The first shot is carried out without correction value.
• The second shot is made with a minus correction.
• The third shot is made with a plus correction.
• After the third shot, the flash bracketing series is automatically deleted.

A flash bracketing series can only occur if the camera supports the setting of a manual flash exposure correction on the flash unit (see ch. 8 and the camera's operating instructions)! Otherwise the shots will be made without correction values!

Setting procedure

• Press the button combination „Select“ until „FB“ flashes in the display.
• Apply the setting desired with the buttons (+) and (-). The possible correction values range from 1/3 to 3 apertures in one-third aperture increments. The correction value will always be shown positively.
  The setting takes effect immediately. After about 5 seconds the display stops flashing and the setting is saved automatically.

For the first shot of a flash bracketing series „FB“ and „A“ re shown in the display. For the second shot „FB“, „B“ and the minus correction values are displayed. For the third shot „FB“, „C“ and the plus correction values are displayed. After the third shot, „FB“ is deleted from the display and the flash bracketing series is deactivated.

It must be reset for another flash bracketing series!

9.4 Auto OFF for the flash unit ©

The auto OFF for the flash unit can be set so that it occurs after 10 minutes, 1 minute or is deactivated.

Setting procedure

• Press button combination „Select“ until the symbol Ⓐ flashes. Apply the setting desired with the buttons (+) and (-).

• When „10min“ is displayed, Auto OFF function will be activated after 10 minutes.

• When „1min“ is displayed, the Auto OFF will be activated after 1 minute.

• When „OFF“ is displayed, the Auto OFF is deactivated.
  The setting takes effect immediately. After about five seconds the display stops flashing and the setting is saved automatically. After activation of the auto OFF the display shows Ⓓ.

The modelling light is a high-frequency stroboscopic flash. It creates the impression of a semi-permanent light for a duration of about 3 seconds. The modelling light enables the user to assess light distribution and the formation of shadows before taking pictures. The modelling light is triggered with the manual firing button ③.

Setting procedure

• Press the button combination „Select“ until „ML“ flashes in the display. Apply the setting desired with the buttons (+) and (-).
• When „ML ON“ is displayed, the modelling light is activated.
• When „ML OFF“ is displayed, the modelling light is deactivated.

The setting takes effect immediately. After about five seconds the display stops flashing and the setting is saved automatically. After activation of the modelling light function „ML“ appears in the display.

In extended zoom mode the zoom position of the main reflector ⑩ is reduced to one level below the focal length of the camera lens. The resulting expanded and broader light coverage provides additional dispersed light (reflections) inside rooms so that a softer flash illumination is possible.

Example:

The focal length of the camera lens is 50 mm. The extended zoom mode sets a 35 mm reflector position on the flash unit. However, 50 mm continues to be shown on the display.

Setting procedure

- repeatedly press button combination „Select“ until „Zoom“ appears in the display and „Ex“ flashes. The required settings can be applied using the (+) and (-) buttons.

- When „Ex On“ is displayed, the extended zoom mode is activated.

- When „Ex OFF“ is displayed, the extended zoom mode is deactivated.

The setting takes effect immediately. After about five seconds the display stops flashing and the setting is saved automatically. After activation of the extended zoom mode „Ex“ appears in the display.

Depending on the system, the extended zoom mode is supported for lens focal lengths of 28 mm or more (35mm format). The camera must be equipped with a CPU lens and be able to transfer data on the lens focal length to the flash unit.

The maximum flash range indicated by the flash unit's display can either be shown in metres or feet.

Setting procedure

- Press the button combination „Select“ until the only the distance dimension „m“ or „ft“ flashes. Apply the setting desired with the buttons (+) and (-).

- When „m“ is displayed, the distance display is in metres.

- When „ft“ is displayed, the distance display is in feet.

The setting takes effect immediately. After about five seconds, the display stops flashing and the setting is saved automatically.

9.8 Synchronisation on the second curtain (REAR)

Several cameras feature second curtain synchronisation (see 11.3)

Setting procedure

• actuate the shutter release in order to transfer data from the flash unit to the camera.
• repeatedly press button combination „Select“ until only „REAR“ appears flashing in the display.

• the required settings can be applied using the (+) and (-) buttons.

• when „REAR On“ is displayed the second curtain synchronisation is activated (REAR-mode).

• when „REAR Off“ is displayed the second curtain synchronisation is deactivated.

The setting takes effect immediately. After about 5 seconds the display stops flashing and the setting is saved automatically. „REAR“ is shown in the display following activation of the second curtain synchronisation.

Second curtain synchronisation cannot be activated when the flash unit is set to high-speed synchronisation FP or HSS (see 7.3).

9.9 Shooting format adjustment (S Zoom)

The display for the position of the main reflector for digital cameras is adapted to the chip format (dimensions of image component) using the zoom size function („S Zoom“).

Setting procedure

• actuate the shutter release in order to transfer data from the flash unit to the camera.
• repeatedly press button combination „Select“ until „Zoom“ appears in the display and „S“ flashes.

• the required settings can be applied using the (+) and (-) buttons.

• when „S On“ is displayed the Zoom-Size function is activated.

• when „S Off“ is displayed the Zoom-Size function is deactivated.

The setting takes effect immediately. After about 5 seconds the display stops flashing and the setting is saved automatically. „S“ is shown in the display following activation of the Zoom-Size function.

9.10 Contrast (CC)

To facilitate subject and pictorial composition, the camera flash can be combined with an external flash unit (mecablitz) to perform so-called contrast control when in TTL- or P-TTL flash mode. Here the camera flash provides 1/3 of the required flash power and the external flash unit provides the remaining 2/3.

Please observe the maximum possible flash range (guide number) of both flash units to ensure the correct operation of the contrast control!

The benefits of contrast control can, however, only be optimally exploited if the external flash unit is set up at a reasonable distance from the built-in camera flash. To do so, the following original Pentax accessories are available:

The "sync cable F 5P", combined with the "adapter foot F" (to hold the external flash unit) and "adapter foot FG" (for the connection to the camera). In this context, please read the notes in the camera's operating instructions.

The auto-focus measuring beam in the mecablitz cannot be used in the contrast control mode.

Adjusting the setting

• Lightly touch the shutter release, so that the data transfer between flash unit and camera occurs.
• Press key combination "Select" repeatedly until "CC" (=contrast control) starts flashing.

• Set as desired, using the keys (+) and (-).

• Contrast control is active "CC On" is on the indicator.

• Contrast control is NOT active "CC Off", is on the indicator.

The setting is immediately effective. After approx. 5 seconds the display stops flashing and the setting is automatically saved. After activating contrast control "P-TTL" will appear in the display.

Contrast control cannot be activated if the high-speed synchronisation FP or HSS is set at the flash unit (see 7.3)!
The contrast function is not activated if the camera flash has not been engaged or the TTL or P-TTL flash mode has not been selected on the flash unit. Synchronisation is with the 1st shutter curtain. The contrast function is automatically cancelled as soon as REAR mode (see 11.3) or the High-Speed flash mode P-TTL-HSS (see 7.3) are activated.

Most integrated camera flash units only light focal lengths up to 35mm (see the camera's operating instructions). If working with a focal length shorter than 35mm, a flash symbol appears in the LC display of the camera or in the camera viewfinder to warn you that the marginal illumination of the subject may not be sufficient! For more details see your camera's operating instructions.

10 Flash techniques

10.1 Bounce flash

Bounce flash illuminates the subject more softly and reduces dense shadows. It also reduces the drop in light from foreground to background that occurs for physical reasons.

The main reflector ⑩ of the flash unit can be swivelled horizontally and tilted vertically for bounce flash. To avoid colour cast in your shots, the reflective surface should be colour-neutral or white.

When tilting the main reflector ⑩ vertically, make sure that it is turned through an angle that is wide enough to prevent direct light from falling on the subject. For this reason the reflector should be tilted at least as far as the 60° lock-in position. Flash ranges do not appear on the display when the main reflector is turned! When the reflector head is tilted, the

main reflector is moved to a position of greater/equal 70 mm in order to prevent the subject from being additionally illuminated by dispersed light. The range and position of the main reflector is not displayed.

10.2 Bounce flash with a reflector card

The use of bounce flash with the integrated reflector card ⑦ can bring out highlights in the eyes of human subjects:

• Tilt the reflector head upwards by 90^ .
• Pull the reflector card ⑦ together with the wide-angle diffuser from above out of the reflector head and forwards.
• Hold the reflector card ⑦ and push the wide-angle diffuser ⑧ back into the reflector head.

10.3 Close-ups / macro shots

In close-ups and macro shots, parallax error between the flash unit and lens may result in shadows on the lower edge of the image. To compensate for this, the main reflector ⑩ can be tilted downwards by an angle of -7°. To do this, depress the reflector unlocking button ⑥ and tilt the reflector downward.

Certain minimum lighting distances must be maintained for close-up shots to avoid over-exposure.

The minimum lighting distance is approximately 10% of the maximum flash range indicated in the display. When the reflector head is tilted downwards, the maximum flash range flashes as an indication. For close-up shots, make sure that the flash light is not shaded by the lens!

11 Flash synchronisation

11.1 Automatic flash sync speed control

Depending on the camera model and camera mode, the shutter speed is switched to flash sync speed when flash readiness is reached (see the camera's operating instructions).

Shutter speeds cannot be set faster than the flash sync speed, or they are switched automatically to the flash sync speed. Various cameras have a sync speed range, for example from 1/30 sec to 1/125 sec (see the camera's operating instructions). The sync speed set by the camera depends on the camera mode, the ambient light, and the focal length of the lens used.

Shutter speeds slower than the flash sync speed can be set according to the camera mode and the selected flash synchronisation (see 11.3 and 11.4).

If a camera with a between-the-lens shutter and high-speed synchronisation (see 7.3) is used, flash sync speed is not controlled automatically. As a result, the flash can be used at all shutter speeds. If you need the full light output of the flash unit, you should not select a shutter speed that is any faster than 1/125 sec.

11.2 Normal synchronisation

In normal synchronisation the flash unit is triggered at the beginning of the shutter time (first curtain synchronisation). Normal synchronisation is the standard mode on all cameras. It is suitable for most flash shots. The camera, depending on the mode being used, is switched to the flash sync speed. Speeds between 1/30 sec. and 1/125 sec. are customary (see the camera's operating instructions). No settings are necessary on the flash unit, nor is there any display for this mode.

11.3 Second curtain synchronisation (REAR)

Some cameras offer the option of second-curtain synchronisation (REAR), in which the flash unit is not triggered until the end of the exposure time. This is

particularly advantageous when used with lower shutter speeds (slower than 1/30 sec.) and moving subjects that have their own source of light. With second-curtain synchronisation, a moving light source will trail a light streak instead of building one up ahead itself, as it does when the flash is synchronised with the first shutter curtain. In this way a „more natural“ image of the photographic situation is produced! Depending on its operating mode, the camera sets shutter speeds slower than its sync speed.

On some cameras the REAR function is not possible in certain operating modes (e.g., certain vari- or subject programs, or with red eye reduction). In these cases, the REAR mode cannot be selected and/or is automatically cancelled or ignored (see camera's operating instructions).

Setting procedure see chapter 9.8.

11.4 Slow synchronisation (SLOW)

A slow exposure (SLOW) gives added prominence to the image background at lower ambient light levels. This is achieved by adjusting the shutter speed to the ambient light. Accordingly, shutter speeds that are slower than the flash sync speed (e.g., shutter speeds up to 30 sec.) are automatically adjusted by the camera. Slow synchronisation is activated automatically on some camera models in connection with certain camera programs (e.g., a night shot program, etc.), or it can be set on the camera (see the camera's operating instructions). No settings are necessary on the flash unit, nor is there any display for this mode.

Slow synchronisation SLOW is set on the camera (see camera's operating instructions)! Use a tripod when shooting with slow shutter speeds to avoid blurred images!

12 Automatic AF measuring beam

The automatic AF measuring beam is activated in the flash unit by the camera when the ambient lighting conditions become inadequate for automatic focusing. It projects onto the subject a striped pattern that the camera can use to focus. Depending on the camera's activated AF sensor, the AF beam has a range of approximately 6 m to 9 m (with a standard 1.7/50 mm lens). The maximum flash range is reached with the camera's central AF sensor. Parallax error between lens and AF measuring beam limits the close-up range with the AF measuring beam to approximately 0.7 m to 1 m.

If the automatic AF measuring beam ⑪ is to be activated by the camera, the „single AF (S)” autofocus mode must be set on the camera and the flash unit must indicate flash readiness. Some camera models support only the camera's internal AF measuring beam. In this case, the automatic AF measuring beam of the flash unit is not activated (as in the case of compact cameras; see the camera's operating instructions).

Low-speed zoom lenses can significantly curtail the range of the AF measuring beam!

Some cameras support the AF measuring beam in the flash unit only with the camera's central AF sensor. If a peripheral AF sensor is selected, then the AF measuring beam will not be activated in the flash unit!

13 Triggering control (auto-flash)

On some cameras the flash will not be fired when the prevailing light is sufficient for an exposure. When the camera shutter release is depressed, no flash exposure is triggered.

In various cameras the triggering control only works in the full program mode or „P“ program or must be activated on the camera (see camera operating instructions).

14 Care and maintenance

Remove dust and grime with a soft dry cloth or silicon-treated cloth. Do not use cleaning agents as these may damage the plastic parts.

14.1 Firmware updates

The flash unit's firmware can be updated through the USB port ⑬ and adjusted to the technical requirements of future cameras (Firmware Update).

For more information, visit the Metz homepage at www.metz.de.

14.2 Reset

The flash unit can be reset to the factory settings when delivered. Press the iModei button for ca. 5 seconds. After ca. 5 seconds „rES“ (= Reset) is shown in the display and the flash unit is reset to the settings as delivered..

This will not affect the firmware updates for the flash unit.

14.3 Flash capacitor forming

The flash capacitor built into the flash unit undergoes physical change if the unit is not switched on for a prolonged period. For this reason it is necessary to switch the unit on for approximately 10 minutes at least once every three months. The power supplied by the power source must be sufficient to cause the flash readiness indicator to light up no more than one minute after the flash unit is switched on.

15 Troubleshooting

Should the flash unit fail to function properly or meaningless content appear on the flash unit display panel, switch the flash unit off with the main switch ① for approximately 10 seconds. Check the camera settings and make sure the foot of the flash unit is mounted correctly in the camera's accessory shoe.

Replace the batteries with new or freshly charged batteries.

The flash unit should function normally again once it is switched back on. If this is not the case, contact your local dealer.

Below is a list of some of the problems that may occur when the flash unit is used. For each item, possible causes and remedies for the problem are listed.

Only the flash operating mode TTL can be chosen and selected on the flash unit.

- Depending on the system, some camera models (depending on the camera's operating mode) only support the TTL flash mode. Other flash modes (manual M etc.) cannot be selected or activated! See chapter 7.

No maximum flash range indication appears on the display panel.

• The main reflector is not in normal position.
• The flash unit has been set to remote operation.

The AF measuring beam of the flash unit is not activated.

• The flash unit is not ready for firing.
• The camera is not in Single AF mode (S-AF).
• The camera supports only its own internal AF measuring beam.
• Some cameras support the AF measuring beam in the flash unit only with the camera's central AF sensor. If a peripheral AF sensor is selected, then the AF measuring beam will not be activated in the flash unit. Activate the central AF sensor.

The reflector position is not automatically adjusted to the current zoom position of the lens.

• The camera is not transmitting any digital data to the flash unit.
• There is no exchange of data between the flash unit and the camera. Tap the camera's shutter release.
• The flash unit is set to manual zoom setting "MZoom".

The sign for the zoom position of the reflector blinks in the display

- Warning advice of shading on the edge of the picture: The focus of the lens (converted to 35 mm - small picture format 24x36) set on the camera is smaller than the zoom position set on the reflector.

The P-TTL or P-TTL-HSS flash modes cannot be called up and/or set on the flash unit.

• The camera does not support this flash mode. See camera's operating instructions.
• No data exchange took place between the flash unit and camera. Lightly touch the shutter release.

The setting for manual TTL/P-TTL flash exposure correction has no effect.

- The camera does not support manual TTL flash exposure correction on the flash unit.

Automatic switching to the flash sync speed fails to occur.

• The camera has a between-the-lens shutter (as do most compact cameras), Switching to sync speed is therefore unnecessary.
• The camera is set to high-speed flash mode P-TTL-HSS. In this case no switching to sync speed occurs.
• The camera operates with shutter speeds that are slower than the flash sync speed. Depending on the camera mode, there is no switch to flash sync speed (see the camera's operating instructions).

The shots have shadows in the bottom of the image.

- Because of parallax error between lens and flash unit, close-up shots may not, depending on the focal length at the bottom of the image, be fully illuminated. Tilt the main reflector downwards or turn the wide-angle diffuser in front of the reflector.

The shots are too dark.

• The subject is beyond the range of the flash unit. Note: Using bounce flash reduces the range of the flash unit.
• The subject contains very bright or highly reflective areas. The metering system of the camera or flash unit is deceived as a result. Set a positive manual flash exposure correction, e.g., +1 EV.

The shots are too bright.

- In close-up shots, overexposure (shots that are too bright) may result if the shutter speed is faster than the flash sync speed. The minimum distance from the subject should be at least 10% of the maximum flash range indicated on the display.

The flash parameters for ISO film speed and the aperture (f-stop) cannot be adjusted on the flash unit.

- There is an exchange of digital data between flash unit and camera through which the ISO and aperture (f) values are automatically adjusted on the flash unit. In this case the manual setting of ISO and aperture isn't possible!

The REAR mode cannot be activated on the flash unit.

• No data exchange took place between the flash unit and camera. Lightly touch the shutter release.
• The flash unit is set to high-speed flash mode P-TTL-HSS (see 16.4).

The contrast function mode cannot be set on the flash unit.

• No data exchange took place between the flash unit and camera. Lightly touch the shutter release.

• The flash unit is set to high-speed flash mode P-TTL-HSS (see 16.4).

• The internal camera flash is not engaged.

• The internal camera flash or the external flash unit (mecablitz) is not flash-ready.

16 Technical data

Max. guide numbers at ISO 100/21°, zoom 105 mm:

In the metric system: 48 In the imperial system: 157

Flash modes:

Standard TTL without measuring preflash, P-TTL, P-TTL HSS, Manuell M.

Manual partial light output levels:

1/1 ... P1/128 light output, in one-third increments.

Flash durations see table 2, page 132:

Colour temperature:

approx. 5600 K

Film speed:

ISO 6 to ISO 6400

Synchronisation:

low-voltage ignition

Number of flashes:

• approx. 90 with NiCad batteries (600 mAh)
• approx. 210 with high-capacity alkaline manganese batteries
• approx. 250 with NiMH batteries (1600 mAh)
• approx. 460 with lithium batteries

Recycling time (at full light output): Approx. 3,5 sec

(at full light output)

Light coverage:

Main reflector from 24 mm (35 mm format)

Main reflector with wide-angle diffuser from 18 mm (35 mm format)

Swivelling ranges and locking positions of the reflector

upwards -7^ 45^ 60^ 75^ 90^

counter-clockwise 30^ 60^ 90^ 120^ 150^ 180^

clockwise 30^ 60^ 90^ 120^

Dimensions, approx., in mm (W x H x D):

71 × 137 × 99

Weight :

approx. 425 gr

Included:

Flash unit with integrated wide-angle diffuser, operating instructions

17 Optional accessories

We accept no liability for malfunctions of or damage to the flash unit caused by the use of accessories of other manufacturers.

- Mecabounce 58-90

(Order No. 000058902)

With this diffuser, soft lighting can be achieved in a very simple manner. It gives your pictures a marvellous soft appearance. Skin tones are captured more faithfully. The maximum working range is reduced by about half in conformity with the loss of light.

- Bounce diffuser 58-23

(Order No. 000058235)

Softens heavy shadows with reflected light.

- Flash unit mounting foot

(Order no. W-F127)

Flash unit mounting foot for slave mode.

Disposal of batteries

Do not dispose of spent batteries with domestic rubbish.

Please return spent batteries to collecting points should they exist in your country! Please return only fully discharged batteries.

Normally, batteries are fully discharged if:

• the device they powered switches itself off and indicates "Spent Batteries".
• they no longer function properly after prolonged use.
  To ensure short-circuit safety please cover the battery poles with adhesive tape.

Dimensioni approssimative in (L x H x P):

71 × 137 × 99

Peso:

425 gr

Dotazione standard:

Table 3: Recycling times and number of flashes with different battery types

Within the framework of the CE approval symbol, correct exposure was evaluated in the course of the electromagnetic compatibility test.

Do not touch the SCA contacts !

In exceptional cases the unit can be damaged if these contacts are touched.

Atención:

Your Metz product was developed and manufactured with high-quality materials and components which can be recycled and/or re-used.

This symbol indicates that electrical and electronic equipment must be disposed of separately from normal garbage at the end of its operational lifetime.

Please dispose of this product by bringing it to your local collection point or recycling centre for such equipment.

This will help to protect the environment in which we all live.

Aerial view of an industrial park with multiple factory buildings and solar panels, surrounded by greenery and water (no visible text or signage)

Modern flat-screen TV unit with black buttons and silver casing (no visible text or symbols)

Consumer electronics

Exterior view of a modern office building (no signage)

Photoelectronics

Close-up of a robotic arm interacting with a mechanical component (no visible text or symbols)

Plastics technology

Close-up of a precision machining operation on a circuit board (no visible text or symbols)

Industrial electronics

Metz - always first class.

C ∈

707 47 0143.A1

D F NL GB I E