G1210DA - Angle Grinder HiKOKI - Free user manual and instructions
Find the device manual for free G1210DA HiKOKI in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Cordless angle grinder (angle grinder) |
| Brand | HiKOKI |
| Model | G1210DA |
| Power Source | 10.8V (12V max) rechargeable lithium-ion battery |
| Battery Voltage | 10.8V / 12V max |
| Wheel Diameter | 100mm (4") |
| No-load Speed | 8,500 min⁻¹ |
| Spindle Thread | M10 × 1.5 |
| Dimensions (L × W × H) | Approx. 262 × 115 × 185 mm |
| Weight (with battery) | Approx. 1.5 kg |
| Grip Design | Compact and lightweight, with anti-slip soft rubber handle |
| Main Functions | Cutting, grinding, rust removal, deburring |
| Safety Devices | Anti-slip start switch, spindle lock button, protective guard |
| Battery Protection | Overcharge, over-discharge, overcurrent protection |
| Included Accessories | Grinding wheel, protective guard, side handle, wrench |
| Maintenance & Cleaning | Regularly clean vents and housing dust; replace carbon brushes |
| Operating Environment | Recommended ambient temperature 0°C-40°C, avoid moisture |
| Repairability | Key components can be replaced individually, easy to repair |
| Charging Time | Approx. 45 minutes (BCL1215 charger, BSL1215 battery) |
| Certifications | Complies with CE, PSE and other standards |
Frequently Asked Questions - G1210DA HiKOKI
What battery does this HiKOKI G1210DA angle grinder use?
It uses a 10.8V (12V max) lithium-ion slide battery, compatible with HiKOKI BSL1215, BSL1220M and other models. Use the original charger for best performance.
How do I install or replace the grinding wheel?
Disconnect the battery, use the spindle lock button to secure the spindle, and loosen the clamping nut with the included wrench. Replace with a new 100mm grinding wheel, then tighten the nut. Ensure the grinding wheel is installed in the correct direction and check the guard position.
What should I do if the wheel doesn't rotate after turning on?
First, check if the battery has sufficient charge and confirm it is installed properly. If it still doesn't turn, overload protection may have been triggered; release the switch, wait a few seconds, and retry. Check that the spindle lock has reset; if the problem persists, inspect the carbon brushes for wear.
Why is there excessive sparking during use?
Sparks are usually caused by friction during metal cutting and are normal. If the sparks are unusually large, the wheel may be dull or unevenly worn; replace the grinding wheel and check whether it is deformed or damaged.
What wheel is recommended for cutting metal?
It is recommended to use HiKOKI genuine 100mm cutting discs, suitable for steel, stainless steel and other metals. Depending on the material, you may choose thin cutting discs or grinding discs. Ensure the maximum permissible speed matches the no-load speed.
How can I operate safely?
Wear safety goggles and a dust mask. Never use the machine without the guard. Use the side handle and hold with both hands; ensure the workpiece is secured before cutting. Do not apply excessive pressure to avoid overloading the machine, and always keep the guard pointing away from your body.
How long does it take to charge the battery? Can I use it while charging?
Charging with the BCL1215 charger takes about 45 minutes (BSL1215 battery). The machine cannot be used while charging; the battery must be removed. Connect the charger to power before inserting the battery; a green light indicates full charge.
How do I maintain the motor and extend its lifespan?
Regularly inspect the carbon brushes; replace them promptly when worn to the limit (typically about 5mm). Keep the motor vents clean and avoid dust buildup. After prolonged continuous operation, allow the machine to cool down intermittently.
Does this machine support variable speed control?
This machine is single-speed, with a no-load speed of approximately 8,500 rpm (see specifications). If you need speed adjustment, choose a model with electronic speed control.
Can it cut stone?
Yes, but you must use a diamond cutting disc and either use water cooling (wet cutting) or choose a disc specifically for dry cutting. Pay attention to dust protection; cut smoothly and avoid lateral force that could damage the wheel.
User questions about G1210DA HiKOKI
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Angle Grinder in PDF format for free! Find your manual G1210DA - HiKOKI and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. G1210DA by HiKOKI.
USER MANUAL G1210DA HiKOKI
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : HiKOKI
Model : G1210DA
Category : Angle Grinder