FD-201Af - Security Camera Brickcom - Free user manual and instructions
Find the device manual for free FD-201Af Brickcom in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Type of product | IP security camera |
| Brand | Brickcom |
| Model | FD-201Af |
| Category | Network surveillance camera |
| Sensor | 1/2.7-inch progressive CMOS |
| Resolution | 1920 x 1080 (2 megapixels) |
| Lens | Fixed 3.6mm |
| Night vision | IR LEDs with up to 20m range |
| Video compression | H.264 |
| Network interface | 10/100Mbps Ethernet |
| PoE support | IEEE 802.3af (Power over Ethernet) |
| Power supply | 12V DC or PoE |
| Dimensions (W x H x D) | 100 x 88 x 60 mm |
| Weight | 350 g |
| Weatherproof rating | IP66 |
| Operating temperature | -20°C to 50°C |
| Storage | MicroSD card slot, NVR support |
| Protocols | TCP/IP, HTTP, RTSP, FTP, SMTP |
| Security | Password protection, HTTPS encryption |
| Maintenance | Clean the lens with a soft, dry cloth |
| Repairability | No user-serviceable parts; contact technical support |
| General information | Suitable for indoor/outdoor surveillance |
Frequently Asked Questions - FD-201Af Brickcom
How do I reset the Brickcom FD-201Af to factory defaults?
Press and hold the reset button for 10 seconds while the camera is powered on. The camera will reboot automatically. Use the default factory settings to access it.
How to set up the camera for the first time?
Connect the camera to your router using an Ethernet cable, then install the Brickcom Surveillance software or use a web browser to access the camera's IP address. Follow the on-screen setup wizard.
How to access the camera remotely?
Enable remote access through the router (port forwarding) or use an NVR with public IP. You can also configure a DDNS domain to reach the camera over the internet.
Does the camera support Power over Ethernet?
Yes, the FD-201Af supports IEEE 802.3af PoE, allowing you to power it with a single Ethernet cable using a PoE switch or injector.
How to update the camera firmware?
Download the latest firmware from the official Brickcom website, log into the camera, go to Maintenance > Firmware Upgrade, and upload the file.
What is the default IP address?
The default IP is 192.168.1.168 with user 'admin' and no password. You can also find the IP using the Brickcom IP Utility tool.
How to record video from the camera?
You can record to a microSD card inserted in the camera, or use an NVR. Configure recording settings in the camera's web interface.
How to enable motion detection?
Go to Event > Motion Detection in the camera settings, enable the function, and draw detection areas. You can set up email alerts or recordings on motion.
What should I do if the camera goes offline?
Check network connections, reboot the camera, verify IP settings, and inspect the power supply. Use the web interface to test connectivity.
How to clean the camera lens?
Use a soft dry or slightly damp microfiber cloth to gently wipe the lens. Avoid using harsh chemicals or abrasive materials.
User questions about FD-201Af Brickcom
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Security Camera in PDF format for free! Find your manual FD-201Af - Brickcom and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. FD-201Af by Brickcom.
USER MANUAL FD-201Af Brickcom
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Brickcom
Model : FD-201Af
Category : Security Camera