DS-K1801MK - Access Control System Hikvision - Free user manual and instructions
Find the device manual for free DS-K1801MK Hikvision in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Access Control System |
| Brand | Hikvision |
| Model | DS-K1801MK |
| Device Type | Access Control Reader with Keypad |
| Mounting Type | Wall-mounting with plastic anchors and screws |
| Power Supply | 12 V DC (operating range 9-14 V) |
| Working Current | ≤ 50 mA (standby), ≤ 120 mA (max) |
| Card Technology | 13.56 MHz Mifare (Mifare 1) |
| Reading Distance | 2-4 cm |
| User Capacity | 1,000 users |
| Card Capacity | 1,000 cards |
| Password Capacity | 1,000 PINs |
| Keypad | 12 keys (0-9, *, #) with backlight |
| Relay Output | 1 relay, NO/NC, max 3 A / 30 V |
| Wiegand Output | Wiegand 26/34 to connect an external controller |
| Door Status Input | Yes, for door contact sensor |
| Exit Button Input | Yes |
| Tamper Alarm | Built-in tamper switch |
| Waterproof Rating | IP65 |
| Operating Temperature | -20 °C to 65 °C |
| Operating Humidity | 10%-90% (non-condensing) |
| Dimensions (W x H x D) | 87.6 x 87.6 x 21.5 mm |
| Weight | 135 g |
| Case Material | ABS plastic |
| Included Accessories | Screws, allen wrench, rubber gasket |
Frequently Asked Questions - DS-K1801MK Hikvision
How do I power the DS-K1801MK?
Connect a 12 V DC power supply to the power terminals. The device accepts 9-14 V DC and consumes up to 120 mA.
How do I add a new card to the device?
Enter programming mode using the master PIN, then choose the user management option and follow the voice prompts. The exact key sequence is detailed in the manual. You can add up to 1,000 cards.
How can I reset the DS-K1801MK to factory defaults?
Press and hold the reset button located behind the front case, or use the reset command in programming mode. This restores the default master PIN and erases all users, cards, and settings.
Which card types are supported by this keypad?
The reader supports 13.56 MHz Mifare cards (Mifare 1). It does not support 125 kHz EM cards. Make sure your cards are compatible.
Can I open the door with my smartphone after pairing via Bluetooth?
No, this is a standalone access control keypad without network or wireless connectivity. It only works with cards, PINs, or a combination of both.
What is the maximum number of users I can store?
You can store up to 1,000 users. Each user can have a card, a PIN, or a card + PIN combination for higher security.
How close should the card be to the reader to be recognised?
The typical reading distance is 2-4 cm. Hold the card flat and close to the reader until the LED lights up and the beep sounds.
How do I connect the electric lock and the exit button?
Wire the lock to the relay output (NO/COM) and the exit button to the exit button input. Check the connection diagram in the manual. Use a separate power supply for the lock if needed.
Why does the keypad beep but the door does not open?
Possible causes: the relay wiring is loose or wrong, the lock power is insufficient, or the door contact input is blocking the relay. Verify the wiring and test the relay output directly.
How do I change the master PIN?
Access programming mode with the current master PIN, select 'Change Master PIN', enter a new 4-8 digit code, and confirm. The default master PIN is usually 12345 (check the manual for your version).
User questions about DS-K1801MK Hikvision
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Access Control System in PDF format for free! Find your manual DS-K1801MK - Hikvision and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. DS-K1801MK by Hikvision.
USER MANUAL DS-K1801MK Hikvision
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Hikvision
Model : DS-K1801MK
Category : Access Control System