WCB-300AP - Security Camera Brickcom - Free user manual and instructions
Find the device manual for free WCB-300AP Brickcom in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | IP Security Camera |
| Model | Brickcom WCB-300AP |
| Dimensions | 70 x 70 x 150 mm (2.8 x 2.8 x 5.9 in) |
| Weight | 400 g (14.1 oz) |
| Power Supply | 12V DC / PoE (Power over Ethernet) |
| Power Consumption | Max 6W |
| Image Sensor | 1/2.7" Progressive CMOS |
| Resolution | 1920 x 1080 (Full HD) |
| Frame Rate | Up to 30 fps |
| Night Vision | IR LEDs up to 30 m (98 ft) |
| Lens | Fixed focal, 3.6 mm, F2.0 |
| Field of View | Horizontal: 92°, Vertical: 52° |
| Video Compression | H.264, MJPEG |
| Audio Support | Yes, one-way audio |
| Network Interface | 10/100 Base-T Ethernet |
| Wireless | 802.11 b/g/n (Wi-Fi) |
| Motion Detection | Yes, configurable sensitivity and zones |
| Storage | MicroSD card up to 128 GB, NAS, NVR |
| Weather Rating | IP66 (indoor/outdoor) |
| Operating Temperature | -20°C to 50°C (-4°F to 122°F) |
| Mounting | Wall mount, ceiling mount |
| Warranty | 2 years |
Frequently Asked Questions - WCB-300AP Brickcom
How do I reset the Brickcom WCB-300AP to factory defaults?
Press and hold the reset button (located on the device) for about 10 seconds using a paperclip until the LED blinks rapidly. The camera will restart with factory settings.
What is the default IP address and login credentials?
The default IP is 192.168.1.168. The default username is admin and password is admin. It is strongly recommended to change the password after first login.
How can I connect the camera to my Wi-Fi network?
First, connect the camera via Ethernet cable to your router. Access the camera's web interface, go to Network Settings > Wireless, scan for your SSID, enter the password, and enable wireless. You can then disconnect the Ethernet cable.
Does the camera support Power over Ethernet (PoE)?
Yes, the Brickcom WCB-300AP supports PoE IEEE 802.3af. You can power it using a PoE switch or injector without needing a separate power adapter.
What mobile apps are compatible with this camera?
The camera is compatible with the Brickcom Viewer app (available for iOS and Android). You can also use third-party software that supports ONVIF standard.
How do I view the camera remotely over the internet?
Enable UPnP or manually forward ports (default HTTP: 80, RTSP: 554) on your router. Then use the camera's DDNS service or your public IP to access it via the mobile app or web browser.
What is the maximum microSD card capacity supported?
The camera supports microSD cards up to 128 GB. Use a Class 10 card for best performance with continuous recording.
Can I use the camera outdoors?
Yes, it has an IP66 weatherproof rating, meaning it is protected against dust and strong water jets. It can operate in temperatures from -20°C to 50°C.
How do I enable motion detection alerts?
Log into the camera's web interface, go to Event > Motion Detection. Enable it, draw detection zones, set sensitivity, and configure email or FTP upload for alerts.
Where can I download the user manual and firmware updates?
Visit notice-facile.com and search for 'Brickcom WCB-300AP'. You can download the PDF manual and check for firmware under the support section.
User questions about WCB-300AP Brickcom
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Security Camera in PDF format for free! Find your manual WCB-300AP - Brickcom and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. WCB-300AP by Brickcom.
USER MANUAL WCB-300AP Brickcom
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Brickcom
Model : WCB-300AP
Category : Security Camera