DS-PDC10AM-EG2-WB - Motion detector Hikvision - Free user manual and instructions
Find the device manual for free DS-PDC10AM-EG2-WB Hikvision in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Type of Product | Motion Detector |
| Brand | Hikvision |
| Model | DS-PDC10AM-EG2-WB |
| Detection Technology | Passive Infrared (PIR) |
| Detection Range | Up to 12 meters |
| Detection Angle | 90 degrees |
| Pet Immunity | Yes (up to 25 kg) |
| Power Supply | 1x CR123A 3V Lithium Battery |
| Battery Life | Up to 3 years (typical use) |
| Wireless Protocol | Hikvision proprietary (868 MHz / 915 MHz) |
| Anti-Masking | Yes |
| Tamper Protection | Yes (rear tamper switch) |
| Low Battery Notification | Yes |
| Operating Temperature | -10°C to 55°C |
| Humidity | Up to 95% (non-condensing) |
| Dimensions (W x H x D) | 110 x 60 x 45 mm |
| Weight | 100 g (including battery) |
| Mounting | Wall or corner mount (bracket included) |
| Mounting Height | 2.0 to 2.5 meters |
| IP Rating | IP41 (indoor use) |
| LED Indicator | Red/Green for alarm and status |
| Maintenance | Clean lens with dry cloth; replace battery annually |
| Safety Standards | Complies with EN 50131-2-2 Grade 2 |
| Spare Parts Available | Battery, mounting bracket |
| Repairability | Battery replacement only; other repairs by authorized service |
Frequently Asked Questions - DS-PDC10AM-EG2-WB Hikvision
How do I pair the DS-PDC10AM-EG2-WB with my alarm panel?
Insert the battery, wait for the LED to flash rapidly, then follow the panel's 'Add Device' procedure. Refer to the panel manual for specific steps.
What is the battery life and how do I know when to replace it?
Battery life is up to 3 years. A low battery signal is sent to the panel, and the LED will flash red every 30 seconds.
Can the detector ignore pets?
Yes, it has pet immunity up to 25 kg. Mount at 2.0-2.5 m to reduce false alarms from animals.
Why is my detector triggering false alarms frequently?
Check for heat sources (radiators, sunlight) near the detection area. Ensure the lens is clean and the detector is not facing a window or ventilation outlet.
How do I test the detector?
Press and hold the tamper switch for 3 seconds to enter test mode. The LED will flash green each time motion is detected. Exit by pressing tamper again or waiting 10 minutes.
What does the LED indicator mean?
Solid green for 2 seconds on startup means normal. Rapid flashing green during pairing. Slow red flash indicates low battery. Red for 1 second when alarm is triggered.
What is the detection range and angle?
The detector covers up to 12 meters with a 90-degree angle. For best performance, install in a corner at the recommended height.
Can I use the detector outdoors?
No, it is designed for indoor use only (IP41). Exposure to rain or extreme temperatures may damage the device.
How do I reset the detector to factory defaults?
Remove the battery, press the tamper switch for 10 seconds, then re-insert the battery. The LED will flash rapidly to confirm reset.
What should I do if the detector stops working?
First, replace the battery. If still not working, check if the device is within range of the panel (max 200 m open field). Contact Hikvision support if needed.
User questions about DS-PDC10AM-EG2-WB Hikvision
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Motion detector in PDF format for free! Find your manual DS-PDC10AM-EG2-WB - Hikvision and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. DS-PDC10AM-EG2-WB by Hikvision.
USER MANUAL DS-PDC10AM-EG2-WB Hikvision
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Hikvision
Model : DS-PDC10AM-EG2-WB
Category : Motion detector