EchoStream EN1223S - Controller Inovonics - Free user manual and instructions
Find the device manual for free EchoStream EN1223S Inovonics in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Wireless Controller |
| Brand | Inovonics |
| Model | EchoStream EN1223S |
| Dimensions | 5.4 x 3.8 x 1.2 inches (137 x 97 x 30 mm) |
| Weight | 6.7 oz (190 g) |
| Power Supply | 12V DC, 500 mA (power adapter included) |
| Battery Backup | 4 x AA alkaline batteries (not included) |
| Frequency | 902-928 MHz (FHSS) |
| Range | Up to 2,000 ft (610 m) line-of-sight |
| Number of Zones | Up to 32 wireless zones |
| Compatible Sensors | Inovonics EchoStream series (PIR, door/window, smoke, etc.) |
| Outputs | Form C relay (NC/NO), voltage trigger |
| Operating Temperature | 32°F to 120°F (0°C to 49°C) |
| Humidity | 5% to 95% non-condensing |
| LED Indicators | Power, RF Link, Alarm, Trouble |
| Supervisory Interval | 65 minutes (check-in from sensors) |
| Mounting | Wall-mountable with included hardware |
| Enclosure Rating | Indoor use only |
| Maintenance | Clean with dry cloth; replace batteries annually |
| Safety | UL/ULC listed for security applications |
| Spare Parts | Power adapter and battery holder available |
| Repairability | Replaceable battery compartment; no user-serviceable internal parts |
| Warranty | 2-year limited |
Frequently Asked Questions - EchoStream EN1223S Inovonics
How do I pair sensors with the EN1223S controller?
Press the Learn button on the controller until the LED flashes rapidly. Activate the sensor (e.g., tamper switch) to transmit its ID. The LED will turn solid green when pairing is successful.
What is the maximum number of sensors supported?
The EN1223S supports up to 32 wireless zones, allowing a mix of different sensor types (PIR, door/window, smoke, etc.).
How do I reset the controller to factory defaults?
To factory reset, press and hold the Learn button for 10 seconds until all LEDs flash three times. This will clear all paired sensors and settings.
What power supply is required?
The controller operates on 12V DC at 500 mA via the included power adapter. It also has a backup battery compartment for 4 AA alkaline batteries.
How long do the backup batteries last?
With fresh alkaline batteries, the backup can power the controller for approximately 4 hours during a power outage (excluding sensor transmissions).
Can I use this controller with non-Inovonics sensors?
No, the EN1223S is designed exclusively for Inovonics EchoStream wireless sensors that operate at 902-928 MHz FHSS. Third-party sensors are not compatible.
What is the range of the wireless system?
Under ideal line-of-sight conditions, the range is up to 2,000 feet (610 meters). Actual range may vary due to building materials and interference.
How do I troubleshoot a sensor that shows a 'trouble' condition?
Check the sensor's battery level and ensure it is within range. Re-pair the sensor by removing and re-adding it. If the trouble persists, replace the sensor's battery or contact support.
Is the controller compatible with alarm panels?
Yes, the controller provides a Form C relay output (normally open/normally closed) and a voltage trigger that can connect to most alarm panels or automation systems.
How do I clean the controller?
Disconnect power and remove batteries. Wipe the enclosure with a soft, dry cloth. Do not use water, solvents, or abrasive cleaners.
User questions about EchoStream EN1223S Inovonics
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Controller in PDF format for free! Find your manual EchoStream EN1223S - Inovonics and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. EchoStream EN1223S by Inovonics.