876A26PF - Gas water heater Rheem - Free user manual and instructions
Find the device manual for free 876A26PF Rheem in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Residential Electric Water Heater |
| Brand | Rheem |
| Model | 876A26PF |
| Capacity | 50 Gallons |
| Voltage | 240V AC |
| Wattage | 4500 W (dual elements) |
| Tank Material | Glass-lined steel |
| Dimensions (H x W x D) | 60.5 x 22 x 22 inches |
| Weight (empty) | 150 lbs |
| Energy Source | Electric |
| First Hour Rating | 62 gallons |
| Recovery Rate | 20.9 gph at 90°F rise |
| Temperature Range | 90°F - 150°F (adjustable thermostat) |
| Safety Features | T&P relief valve, automatic shutoff, thermal cutoff |
| Warranty | 6 years (tank and parts) |
| Repair Parts | Thermostat, heating elements, anode rod, relief valve |
| Maintenance | Annual flushing and anode rod inspection |
| Installation Code | Compliant with ASME and ANSI standards |
Frequently Asked Questions - 876A26PF Rheem
How do I reset the thermostat on my Rheem 876A26PF water heater?
To reset the thermostat, locate the two access panels on the side of the tank. Remove the cover and insulation. Press the red reset button on the upper thermostat. If the heater still doesn't operate, check for a tripped circuit breaker.
What is the recommended temperature setting for the Rheem 876A26PF?
The recommended setting is 120°F to prevent scalding and reduce energy consumption. Adjust the dial on the thermostat using a screwdriver. Allow the water to stabilize for a few hours before checking.
Why is my Rheem water heater making a popping noise?
Popping noises are usually caused by sediment buildup on the heating elements. To fix, drain and flush the tank annually. If the noise persists, the elements may need to be replaced.
How do I drain my Rheem 876A26PF water heater?
Turn off the power supply at the circuit breaker. Connect a garden hose to the drain valve at the bottom. Open the valve and a nearby hot water faucet to allow air in. Drain until the water runs clear, then close the valve and refill before restoring power.
What size breaker does the Rheem 876A26PF require?
The 876A26PF requires a 30-amp double-pole breaker with 10 AWG copper wire. Always consult a licensed electrician for installation.
How long does the Rheem 876A26PF take to heat a full tank?
With 4500W elements, it takes approximately 60-70 minutes to heat a full 50-gallon tank from cold water (50°F) to 120°F.
Does the Rheem 876A26PF have a self-cleaning feature?
No, this model does not have a self-cleaning feature. Manual flushing every 6-12 months is required to remove sediment buildup.
Can I install the Rheem 876A26PF myself?
Installation should be performed by a qualified professional to comply with local plumbing and electrical codes. Improper installation can cause property damage or injury.
Where can I find replacement parts for the Rheem 876A26PF?
Replacement parts such as thermostats, heating elements, and anode rods can be purchased through Rheem authorized dealers or online retailers. Use the model number to ensure compatibility.
What does the warranty cover on the Rheem 876A26PF?
The warranty covers a 6-year leak protection for the tank and a 6-year parts replacement. Labor and incidental costs are not included. Registration is required.
User questions about 876A26PF Rheem
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Gas water heater in PDF format for free! Find your manual 876A26PF - Rheem and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. 876A26PF by Rheem.
USER MANUAL 876A26PF Rheem
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Rheem
Model : 876A26PF
Category : Gas water heater