TEPC 55 - Water heater Rheem - Free user manual and instructions
Find the device manual for free TEPC 55 Rheem in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Electric Water Heater |
| Brand | Rheem |
| Model | TEPC 55 |
| Capacity | 55 Gallons |
| Dimensions (Height x Diameter) | 60 inches x 20 inches |
| Weight (Empty) | 150 lbs |
| Recovery Rate (90°F rise) | Approx. 40 GPH |
| Power Supply | 240 V / 4500 W (dual elements) |
| Energy Factor | 0.95 (estimated) |
| Temperature Range | 90°F to 150°F |
| Thermostat | Adjustable upper and lower |
| Anode Rod | Magnesium (replaceable) |
| Pressure Relief Valve | Included (150 psi) |
| Insulation | Polyurethane foam (R-10) |
| Maintenance | Annual flushing, anode rod inspection every 3 years |
| Safety Features | High temperature cutoff, pressure relief valve, thermal expansion tank recommended |
| Spare Parts Availability | Thermostats, heating elements, anode rod, T&P valve (universal fit) |
| Repairability | DIY-friendly: accessible elements and thermostats |
| Certifications | UL, Energy Star |
Frequently Asked Questions - TEPC 55 Rheem
What is the recommended temperature setting for the TEPC 55?
For energy savings and safety, set the thermostat to 120°F. This reduces the risk of scalding and lowers standby heat loss.
How do I drain and flush the water heater?
Turn off power, attach a hose to the drain valve, open a hot water faucet, then open the valve. Flush until water runs clear. Close valve, remove hose, and restore power.
How often should I replace the anode rod?
Inspect the magnesium anode rod every 3 years. Replace if it is less than 1/2 inch thick or has significant corrosion.
Why is my water heater not producing hot water?
Check if the circuit breaker is tripped, the high-temperature limit switch is reset, or the lower heating element is burnt out. Use a multimeter to test continuity.
What size expansion tank do I need for the TEPC 55?
A 2-gallon thermal expansion tank is typically sufficient for a 55-gallon water heater to prevent pressure fluctuations.
Can I install the water heater myself?
Basic plumbing and electrical skills are needed. Follow local codes. Use 10 AWG wire and a 30A double-pole breaker. A permit may be required.
How do I clean the aerator or reduce sediment?
Sediment build-up can be reduced by flushing the tank annually. Install a whole-house sediment filter before the heater for extra protection.
What is the pressure relief valve rated at?
The T&P valve is rated at 150 psi and should be tested annually by lifting the lever to ensure it opens and closes properly.
Are replacement parts available for the TEPC 55?
Yes, standard Rheem parts like upper/lower thermostats, heating elements (4500W), and anode rods are widely available at hardware stores.
How can I improve energy efficiency?
Insulate the first 6 feet of the hot water pipe, lower the thermostat to 120°F, and consider adding an insulating blanket if the unit is in an unheated space.
User questions about TEPC 55 Rheem
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Water heater in PDF format for free! Find your manual TEPC 55 - Rheem and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. TEPC 55 by Rheem.
USER MANUAL TEPC 55 Rheem
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Rheem
Model : TEPC 55
Category : Water heater