LH-082 - Uncategorized Omnitronic - Free user manual and instructions
Find the device manual for free LH-082 Omnitronic in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | LED PAR Can |
| Model | LH-082 |
| Brand | Omnitronic |
| Dimensions (L x W x H) | 250 x 250 x 300 mm |
| Net Weight | 2.5 kg |
| Power Supply | AC 100-240V, 50/60 Hz |
| Power Consumption | 60 W |
| Light Source | 12 x 1W RGB LED |
| Control Modes | DMX512 (4/7/8 channels), Master/Slave, Sound Active, Auto |
| DMX Connectors | 3-pin XLR (In/Out) |
| Coverage Angle | 25° beam angle |
| Housing Material | Aluminum |
| Cooling | Passive convection |
| Mounting Options | Floor stand, truss clamp (included) |
| Operating Temperature | -10°C to 40°C |
| IP Rating | IP20 |
| Cleaning Instructions | Wipe with a soft, dry cloth; avoid solvents |
| Safety Instructions | Use rated power cord, do not cover ventilation slots, disconnect before maintenance |
| Spare Parts Available | Fuse, power cord, LED board (upon request) |
| Included Accessories | Power cord, DMX cable, mounting bracket, manual |
| Warranty | 2 years |
Frequently Asked Questions - LH-082 Omnitronic
How do I set up the LH-082 for DMX control?
Connect the DMX controller to the fixture's DMX IN using a 3-pin XLR cable. Set the fixture's DMX address via the control panel. Refer to the manual for channel mapping.
Can I use the LH-082 without a DMX controller?
Yes, the fixture has built-in sound active and auto modes. In sound active mode, the lights respond to music via the built-in microphone.
What is the beam angle of the LH-082?
The beam angle is approximately 25 degrees, providing a narrow spot effect suitable for stage lighting.
How do I replace a blown fuse?
Disconnect the fixture from power. Locate the fuse holder near the power input. Use a flathead screwdriver to open it and replace the fuse with one of matching rating (e.g., T2A/250V). Do not use a higher rating.
Is the LH-082 suitable for outdoor use?
No, the fixture has an IP20 rating, meaning it is not water-resistant. Use only indoors or in a dry environment.
Why is the fixture not responding to DMX?
Check that the DMX cable is properly connected and not damaged. Ensure the DMX address matches the controller's channel assignment. Try terminating the DMX chain with a 120-ohm resistor on the last fixture.
Can I daisy-chain multiple LH-082 fixtures?
Yes, connect the DMX OUT of the first fixture to the DMX IN of the next. Up to 32 fixtures can be daisy-chained on a single DMX universe.
How do I clean the LH-082?
Use a soft, dry cloth to wipe the housing. For the lenses, use a lens cleaning cloth or a mild glass cleaner. Avoid abrasive cleaners or solvents.
What does the 'Master/Slave' mode do?
In Master/Slave mode, one fixture (Master) sends its internal program to other fixtures (Slaves). Connect DMX OUT of Master to DMX IN of Slaves. Set Slaves to Slave mode. They will sync to the Master's behavior.
The fixture is not turning on. What should I do?
Verify the power cord is connected to a working outlet. Check the fuse. If the fuse is fine and the outlet works, the fixture may need service. Contact Omnitronic support.
User questions about LH-082 Omnitronic
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual LH-082 - Omnitronic and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. LH-082 by Omnitronic.
USER MANUAL LH-082 Omnitronic
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Omnitronic
Model : LH-082
Category : Uncategorized