VFI 1500 RMG PF1 - Alimentation sans coupure PowerWalker - Free user manual and instructions
Find the device manual for free VFI 1500 RMG PF1 PowerWalker in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Uninterruptible Power Supply (UPS) |
| Model | VFI 1500 RMG PF1 |
| Brand | PowerWalker |
| Power Rating | 1500 VA / 1350 W |
| Topology | Online Double Conversion (VFI) |
| Waveform | Pure Sine Wave |
| Input Voltage | 230 VAC |
| Output Voltage | 230 VAC |
| Frequency | 50/60 Hz (Auto-sensing) |
| Form Factor | Rackmount (2U) |
| Dimensions (W x H x D) | 482 x 85 x 450 mm |
| Weight | 25 kg |
| Battery Type | Valve-Regulated Lead-Acid (VRLA) |
| Battery Capacity | 3 x 12V / 9Ah (Typical) |
| Typical Runtime at Half Load | 15-20 minutes |
| Recharge Time | 4-6 hours to 90% |
| Protection Features | Overload, Short Circuit, Surge Protection, EMI/RFI Filtering |
| Interfaces | USB, RS-232, Emergency Power Off (EPO) |
| Operating Temperature | 0°C to 40°C |
| Audible Noise | < 45 dB at 1 m |
| Maintenance | Replace batteries every 3-5 years |
Frequently Asked Questions - VFI 1500 RMG PF1 PowerWalker
What is the typical runtime of the PowerWalker VFI 1500 RMG PF1?
At half load (750 VA), the runtime is approximately 15-20 minutes. At full load (1500 VA), it is around 5-7 minutes. Actual runtime depends on battery health and load characteristics.
How do I replace the batteries in this UPS?
The UPS uses internal VRLA batteries. To replace, disconnect the UPS from mains and loads, remove the front panel, disconnect the battery connectors, and slide out the battery pack. Replace with same type (3x12V/9Ah). Ensure proper polarity. Recharge for at least 6 hours before use.
Can the VFI 1500 RMG PF1 be used with a generator?
Yes. The UPS has a wide input voltage range (160-300 VAC) and frequency range (40-70 Hz), making it compatible with most generators. However, ensure the generator output is clean and stable for proper operation.
What type of loads can be connected to this UPS?
This UPS supports resistive and capacitive loads, including computers, servers, networking devices, and sensitive electronic equipment. Do not connect motors or laser printers exceeding 500W due to high startup current.
How do I connect the UPS to my network for monitoring?
Use the USB or RS-232 port to connect to a computer. Install PowerWalker monitoring software (available on their website). For network monitoring, an optional SNMP card can be added to the communication slot.
What does the 'VFI' stand for?
VFI stands for Voltage and Frequency Independent, meaning the UPS constantly inverts AC to DC and back to AC, providing pure sine wave output regardless of input fluctuations. This is also known as online double conversion topology.
How long does the battery take to recharge?
After a full discharge, the UPS recharges the batteries to 90% capacity in approximately 4-6 hours. Full recharge may take up to 8 hours.
Is the UPS rackmountable? What size is it?
Yes, it is a 2U rackmount unit. Dimensions are 482 mm (19 inches) wide, 85 mm high, and 450 mm deep. It can be installed in a standard 19-inch rack with included rack ears.
What maintenance is required for the UPS?
Periodically check the air filters and clean them if dusty. Ensure proper ventilation. Replace batteries every 3-5 years or when runtime drops significantly. Test the UPS every 3 months by running on battery for a few minutes.
The UPS beeps continuously, what does it mean?
Continuous beeping usually indicates a battery fault or overload. Check if the load exceeds the rated 1350W. If load is normal, the battery may need replacement. Refer to the user manual for detailed alarm codes.
User questions about VFI 1500 RMG PF1 PowerWalker
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Alimentation sans coupure in PDF format for free! Find your manual VFI 1500 RMG PF1 - PowerWalker and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. VFI 1500 RMG PF1 by PowerWalker.
USER MANUAL VFI 1500 RMG PF1 PowerWalker
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : PowerWalker
Model : VFI 1500 RMG PF1
Category : Alimentation sans coupure