VPL-EW7 - Projector SONY - Free user manual and instructions

Product Type	LCD Projector
Model	Sony VPL-EW7
Display Technology	3LCD
Native Resolution	WXGA (1280 x 800)
Brightness	2500 lumens
Contrast Ratio	2000:1
Lamp Type	210 W UHP lamp
Lamp Life (Normal/ECO)	3000 / 6000 hours
Projection Lens	1.3x manual zoom/focus
Keystone Correction	Vertical: ±30 degrees
Input Terminals	HDMI (x1), VGA (x2), Composite (x1), S-Video (x1)
Output Terminals	Moniter Out (VGA x1), Audio Out (2.5mm stereo)
Audio	Built-in 1W monaural speaker
Dimensions (W x H x D)	315 x 75 x 230 mm
Weight	2.5 kg
Power Consumption	270 W (typical)
Power Supply	AC 100-240V, 50/60 Hz
Operating Temperature	0°C to 35°C
Maintenance	Clean air filter every 500 hours; replace lamp at end of life
Security Features	Kensington lock slot, password protection
Repairability / Spare Parts	Lamp and filter kits available; service by authorized technicians

Frequently Asked Questions - VPL-EW7 SONY

How do I replace the lamp on the Sony VPL-EW7?

Turn off and unplug the projector. Wait for it to cool. Remove the lamp cover on the bottom, loosen the lamp screws, pull out the old lamp, insert the new one, tighten screws, and replace the cover. Reset the lamp timer in the menu.

What is the maximum projection size?

With a 1.3x zoom lens, you can project from 40 to 300 inches diagonally, depending on the distance.

Can I connect my laptop to this projector?

Yes, use the VGA or HDMI input. For older laptops, VGA is common. For newer ones, HDMI provides better quality.

How often should I clean the air filter?

Clean the air filter every 500 hours of use. Remove the filter cover, gently clean with a vacuum or soft brush, and reinstall.

Does the projector have built-in speakers?

Yes, it has a built-in 1W monaural speaker suitable for basic audio. For better sound, connect external speakers to the audio out.

How do I adjust keystone distortion?

Use the Keystone button on the remote or menu. Adjust vertical keystone up to ±30 degrees to correct trapezoid shape.

What is the warranty on this projector?

Sony typically offers a 3-year warranty on parts and labor, but check your local dealer for specifics.

Can I mount this projector on the ceiling?

Yes, the VPL-EW7 supports ceiling mounting. Use a compatible universal mount and ensure the projector is upside down; adjust the image flip in the menu.

How do I reset the lamp timer?

After replacing the lamp, go to Menu > Settings > Lamp Timer > Reset. Confirm to clear the lamp usage hours.

What resolutions does the projector support?

Native WXGA (1280x800). It can also display 1080p, 720p, and other resolutions compressed or scaled.

USER MANUAL VPL-EW7 SONY

Operating Instructions

Before operating the unit, please read this manual thoroughly and retain it for future reference.

VPL-EX70

VPL-EX7

VPL-EW7

Not all models are available in all countries.

Please check with your local Sony Authorized Dealer.

WARNING

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

THIS APPARATUS MUST BE EARTHED.

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the manufacturer. When you dispose of the battery, you must obey the law in the relative area or country.

WARNING

When installing the unit, incorporate a readily accessible disconnect device in the fixed wiring, or connect the power plug to an easily accessible socket-outlet near the unit. If a fault should occur during operation of the unit, operate the disconnect device to switch the power supply off, or disconnect the power plug.

WARNING (VPL-EW7 only): THIS WARNING IS APPLICABLE FOR USA ONLY.

If used in USA, use the UL LISTED power cord specified below.

DO NOT USE ANY OTHER POWER CORD.

Plug Cap: Parallel blade with ground pin (NEMA 5-15P Configuration)

Cord Type: SJT, three 16 or 18 AWG wires

Length: Minimum 1.5 m (4 ft. 11 in.), Less than 4.5 m (14 ft. 9 5/8 in.)

Rating: Minimum 10 A, 125 V

Using this unit at a voltage other than 120 V may require the use of a different line cord or attachment plug, or both. To reduce the risk of fire or electric shock, refer servicing to qualified service personnel.

WARNING: THIS WARNING IS APPLICABLE FOR OTHER COUNTRIES.

1. Use the approved Power Cord (3-core mains lead) / Appliance Connector / Plug with earthing-contacts that conforms to the safety regulations of each country if applicable.
2. Use the Power Cord (3-core mains lead) / Appliance Connector / Plug conforming to the proper ratings (Voltage, Ampere).

If you have questions on the use of the above Power Cord / Appliance Connector / Plug, please consult a qualified service personnel.

IMPORTANT

The nameplate is located on the bottom.

For customers in Norway

This equipment can be connected to an IT power distribution system.

For the customers in the U.S.A. (VPL-EW7 only)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

All interface cables used to connect peripherals must be shielded in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

If you have any questions about this product, you may call; Sony Customer Information Service Center 1-800-222-7669 or http://www.sony.com/

Declaration of Conformity

Trade Name: SONY

Model: VPL-EW7

Responsible party: Sony Electronics Inc.

Address: 16530 Via Esprillo, San Diego, CA 92127 U.S.A.

Telephone Number: 858-942-2230

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

For the customers in Canada (VPL-EW7 only)

This Class B digital apparatus complies with Canadian ICES-003.

For the customers in Europe

The manufacturer of this product is Sony Corporation, 1-7-1 Konan, Minato-ku, Tokyo, 108-0075 Japan.

The Authorized Representative for EMC and product safety is Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or guarantee matters please refer to the addresses given in separate service or guarantee documents.

For the State of California, USA only (VPL-EW7 only)

Perchlorate Material - special handling may apply, See

www.dtsc.ca.gov/hazardouswaste/perchlorate

Perchlorate Material: Lithium battery contains perchlorate.

Disposal of the used lamp

For the customers in the USA (VPL-EW7 only)

Lamp in this product contains mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance (www.eiae.org).

For the customers in Taiwan only (VPL-EW7 only)

Please recycle the used battery.

Table of Contents

Precautions ....5

Notes on Installation and Usage ...... 6

Overview

About the Supplied Manuals ......9

Included Attachments 9

Location and Function of Controls .. 11

Top/Right Side/Front 11

Rear/Bottom 11

Control Panel 13

Connector Panel 15

Remote Commander .... 16

Projecting the Picture

Installing the Projector .... 18

Connecting the Projector .... 18

Connecting a Computer ...... 18

Connecting a VCR 20

Projecting 21

Turning Off the Power 23

Convenient Functions

Selecting the Menu Language ...... 24

Security Lock 25

Other Functions 27

Direct Power On/Off Function ... 27

Off & Go Function 27

Effective Tools for Your

Presentation 27

Adjustments and Settings Using a Menu

Using a MENU 28

The PICTURE SETTING Menu .....30

The INPUT SETTING Menu ......32

About the Preset Memory No. .....33

The SET SETTING Menu ....34

The MENU SETTING Menu ......36

The INSTALL SETTING Menu .....37

The INFORMATION Menu ......39

Maintenance

Replacing the Lamp ....41

Cleaning the Air Filter ....43

Others

Troubleshooting ....44

Messages List ....46

Specifications ....48

Installation Diagram ....53

Floor Installation (Front Projection) ....53

Ceiling Installation (Front Projection) ....55

Dimensions 57

Index 59

Precautions

Safety

• Check that the operating voltage of your unit is identical with the voltage of your local power supply. If voltage adaptation is required, consult with qualified Sony personnel.
• Should any liquid or solid object fall into the cabinet, unplug the unit and have it checked by qualified personnel before operating it further.
• Unplug the unit from the wall outlet if it is not to be used for several days.
• To disconnect the cord, pull it out by the plug. Never pull the cord itself.
• The wall outlet should be near the unit and easily accessible.
• The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off.
• Do not look into the lens while the lamp is on.
• Do not place your hand or objects near the ventilation holes. The air coming out is hot.
• Be careful not to get your fingers caught in the adjuster.
• Do not spread a cloth or paper under the unit.

Illumination

• To obtain the best picture, the front of the screen should not be exposed to direct lighting or sunlight. - Ceiling-mounted spot lighting is recommended. Use a cover over fluorescent lamps to avoid lowering the contrast ratio. - Cover any windows that face the screen with opaque draperies. - It is desirable to install the unit in a room where floor and walls are not of light-reflecting material. If the floor and walls are of reflecting material, it is recommended that the carpet and wall paper be changed to a dark color.

Preventing internal heat build-up

The unit is equipped with ventilation holes (intake) and ventilation holes (exhaust). Do not block or place anything near these holes, or internal heat build-up may occur, causing picture degradation or damage to the projector.

Cleaning

Before cleaning

Be sure to disconnect the AC power cord from the AC outlet.

Cleaning the air filter

• Clean the air filter whenever you replace the lamp.
• Refer to the “Cleaning the Air Filter” on page 43 for the air filter cleaning.

Cleaning the lens

The lens surface is especially treated to reduce reflection of light.

As incorrect maintenance may impair the performance of the projector, take care with respect to the following:

• Avoid touching the lens. To remove dust on the lens, use a soft dry cloth. Do not use a damp cloth, detergent solution, or thinner.
• Wipe the lens gently with a soft cloth such as a cleaning cloth or glass cleaning cloth.
• Stubborn stains may be removed with a soft cloth such as a cleaning cloth or glass cleaning cloth lightly dampened with water.
• Never use solvent such as alcohol, benzene or thinner, or acid, alkaline or abrasive detergent, or chemical cleaning cloth, as they will damage the lens surface.

Cleaning the cabinet

• Clean the cabinet gently with a soft dry cloth. Stubborn stains may be removed with a cloth lightly dampened with mild detergent solution, followed by wiping with a soft dry cloth.
• Use of alcohol, benzene, thinner or insecticide may damage the finish of the cabinet or remove the indications on the cabinet. Do not use these chemicals.
• If you rub on the cabinet with a stained cloth, the cabinet may be scratched.
• If the cabinet is in contact with a rubber or vinyl resin product for a long period of time, the finish of the cabinet may deteriorate or the coating may come off.

LCD data projector

This LCD data projector is manufactured using high-precision technology. You may, however, see tiny black points and/or bright points (red, blue, or green) that appear continuously on the LCD data projector. This is a normal result of the manufacturing process and does not indicate a malfunction. When images are projected onto screens from multiple LCD data projectors, they may generate color distinctions because each projector has its own color balance even if the projectors are the same models.

Notes on Installation and Usage

Unsuitable Installation

Do not install the projector in the following situations. Installation in these situations or locations may cause a malfunction or damage to the unit.

Poorly ventilated locations

• Allow adequate air circulation to prevent internal heat build-up. Do not place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation holes. When internal heat builds up due to blockage of ventilation holes, the temperature sensor will function, and the power will be turned off automatically.
• Leave space of more than 30 cm (11 7/8 inches) around the unit.
• Be careful not to allow the ventilation holes to inhale tiny objects such as pieces of paper or clumps of dust.

Hot and humid

• Avoid installing the unit in a location where the temperature or humidity is very high, or the temperature is very low.
• To avoid moisture condensation, do not install the unit in a location where the temperature may rise rapidly.

Locations subject to direct cool or warm air from an air-conditioner

Installing the projector in such a location may cause a malfunction of the unit due to moisture condensation or a rise in temperature.

Near a heat or smoke sensor

Malfunction of the sensor may occur.

Very dusty, extremely smoky locations

Avoid installing the unit in a very dusty or extremely smoky environment. Otherwise, the air filter will become obstructed, and this may cause a malfunction of the unit or damage it. Dust preventing the air passing through the filter may cause a rise in the internal temperature of the unit. Clean the air filter whenever you replace the lamp.

Unsuitable Conditions

Do not use the projector under the following conditions.

Do not stand the unit upright on one side

Avoid using the unit standing upright on its side. It may cause malfunction.

Do not tilt the unit to the right or left

Avoid tilting the unit to an angle of 15 degrees, and avoid installing the unit in any way other than placing it on a level surface or suspending from the ceiling. Such an installation may cause color shading or shorten the lamp life excessively.

Do not block the ventilation holes

Avoid using a thick-piled carpet or anything that covers the ventilation holes (exhaust/intake); otherwise, internal heat may build up.

Do not place a blocking object just in front of the lens

Do not place any object just in front of the lens that may block the light during projection. Heat from the light may damage the object. Use the PIC MUTING key to cut off the picture.

Do not use the Security bar for transporting or installation

Use the Security bar at the rear of the projector for a purpose of preventing theft, by attaching a commercially available theft prevention cable for example. If you lift the projector by holding the Security bar, or hang the projector by using this bar, it may cause the projector to fall or be damaged.

Usage at High Altitude

When using the projector at an altitude of 1,500 m or higher, turn on “High Altitude Mode” in the INSTALL SETTING menu. Failing to set this mode when using the projector at high altitudes could have adverse effects, such as reducing the reliability of certain components.

Notes on Use

Note on carrying the projector

The unit is manufactured using high-precision technology. When transporting the unit stored in the carrying case, do not drop the unit or subject it to shock, as this may cause damage. When storing the unit in the carrying case, disconnect the AC power cord and all other connecting cables or cards, and store the supplied accessories in a pocket of the carrying case.

Note on the screen

When using a screen with an uneven surface, a striped pattern may rarely appear on the screen depending on the distance between the screen and the projector or the zooming magnification settings used. This is not a malfunction of the projector.

About the Supplied Manuals

The following manuals are supplied with the projector.

Manuals

Quick Reference Manual (separately printed manual)

This manual describes basic operations for projecting pictures after you have made the required connections. It also describes important precautions for safe handling and use of this projector.

Operating Instructions (on the CD-ROM) (this manual)

This Operating Instructions describes the setup and operations of this projector.

Note

You must have Adobe Acrobat Reader 5.0 or higher installed to read the Operating Instructions stored on the CD-ROM.

Included Attachments

The package for this product includes the Main unit (projector) and the following attachments. Check them before use.

Main unit (projector) (1)

RM-PJ6 Remote Commander (1)

HD D-sub 15 pin cable (1.8 m) (1) (1-967-100-11/Sony)

Carrying case (1)

CR2025 Lithium battery (1) (installed in the

Remote Commander)

AC power cord (1)

Lens cap (1)

Operating Instructions (CD-ROM) (1)

Quick Reference Manual (1)

Security Label (1)

Location and Function of Controls

Top/Right Side/Front

Rear/Bottom

① Ventilation holes (exhaust)

② Lens

Remove the lens cover before projection.

③ Front remote control detector

④ Control panel

For details, see "Control Panel" on page 13.

⑤ Zoom ring

Adjusts the picture size.

⑥ Focus ring

Adjusts the picture focus.

⑦ Ventilation holes (intake)/Air filter cover

⑧ Adjusters (fore pad)

⑨ Lamp cover

⑩ Adjuster

⑪ Connector Panel

For details, see "Connector Panel" on page 15.

⑫ AC IN socket

Connects the supplied AC power cord.

⑬ Adjuster adjustment button

For details, see "Using the adjuster" on page 22.

⑭ Speaker

⑮ Security bar

An anti-theft chain or wire (commercially available) can be connected to it. If it is difficult to pull out, pull out the Security bar using a screwdriver.

⑯ Security lock

Connects to an optional security cable (from Kensington).

Web page address: http://www.kensington.com/

Note

To maintain optimal performance, clean the air filter whenever you replace the lamp.

For details, see "Cleaning the Air Filter" on page 43.

① I/⏻ (On/Standby) key

Turns on the projector when the projector is in standby mode. To turn off the power, press the I/⏻ key twice according to the message or hold the I/⏻ key for about one second.

Lights up or flashes under the following conditions:

• Lights in red when the AC power cord is plugged into a wall outlet. Once the projector is in standby mode, you can turn it on with the I/① key.
• Flashes in red when the temperature becomes high inside the projector, or when the projector fails to operate.
• Lights in green when the power is turned on, and when it is ready to operate.
• Flashes in green from the time when the projector is turned on until the projector is ready to operate. Also, flashes in green while the cooling fan is running after the power is turned off with the I/⏻ key. The fan runs for

about 90 seconds after the power is turned off.

• Lights in orange when the power saving mode is on.

For detail, see page 23.

②INPUT key

Selects an input signal. The input signal will change whenever you press the key.

③ ENTER/▲/▼/◄/► (Arrow) keys

Used to enter the settings of items in the menu system, select a menu, or make various adjustments.

④ LAMP/COVER indicators

Flashes in orange under the following conditions:

• A repetition rate of 2 flashes when the lamp cover or air filter cover is not secured firmly.
• A repetition rate of 3 flashes when the lamp has reached the end of its life or reaches a high temperature.

For detail, see page 46.

⑤MENU key

Displays the on-screen menu. Press again to clear the menu.

⑥ PIC MUTING key

Cuts off the picture. Press again to restore the picture.

①VIDEO IN connector

• S VIDEO (mini DIN 4-pin):

Connects to the S video output of video equipment.

• VIDEO (phono type):

Connects to the video output of video equipment.

• AUDIO (stereo minijack) (VPL-EW7 only):

To listen to sound output from video equipment, connect via this jack to the audio output of the video equipment.

②AUDIO INPUT connector (VPL-EX70/EX7 only)

Inputs audio signal attached to the image from INPUT A, INPUT B (VPL-EX70 only) or VIDEO.

③INPUT A connector

- RGB (HD D-sub 15-pin, female): Inputs a computer signal, video GBR signal, component signal, or DTV signal depending on the connected equipment.

Connects to the output connector of equipment using the supplied cable or an optional cable.

• AUDIO (stereo minijack) (VPL-EW7 only):

To listen to sound output from computer, connect via this jack to the audio output of the computer.

For details, see "Connecting a

Computer" on page 18 and

"Connecting a VCR" on page 20.

④ INPUT B connector

- RGB connector (HD D-sub 15-pin, female) (VPL-EX70 only):

Inputs a computer signal.

Connects to the output connector of equipment using the supplied cable or an optional cable.

- Digital RGB/Component connector (for HDMI and HDCP) (VPL-EW7 only):

Connects to the video output connector of the video equipment or the computer equipped with HDMI/DVI output connector (digital).

⑤ OUTPUT connector

• MONITOR (HD D-sub 15-pin female):

Connects to the input connector of the monitor. Only the computer signal on the current channel is output from among the signals connected to INPUT A or INPUT B (VPL-EX70 only).

• AUDIO (stereo minijack):

Connects to the active speaker. Adjust the volume with VOLUME +/- on the remote commander.

In VPL-EX70/EX7:

When VIDEO, S VIDEO, INPUT A or INPUT B (VPL-EX70 only) is selected, the output audio is the signal input to AUDIO INPUT.

In VPL-EW7:

When INPUT A is selected, the output audio is the signal input to AUDIO of INPUT A. When INPUT B is selected, the output audio is the signal input to HDMI connector of INPUT B. When VIDEO or S VIDEO is selected, the output audio is the signal input to AUDIO of VIDEO IN.

⑥ REMOTE RS-232C connector (D-sub 9-pin female)

Connects to the connector of the computer when you operate the projector from the computer.

Remote Commander

The keys that have the same names as those on the control panel function identically.

①NETWORK key

This function is not provided in this projector.

② INPUT key

③ MENU key

④ ENTER/ ▲/▼/◄/► (Arrow) keys

⑤ RESET key

Resets the value of an item to its factory preset value or returns the enlarged image with D ZOOM key to its original size. This key functions when the menu or a setting item is displayed on the screen.

⑥ AUTO FOCUS key

This function is not provided in this projector.

⑦ D ZOOM (Digital Zoom) +/- key

Enlarges the image at a desired location on the screen. (Digital Zoom function)

⑧ VOLUME +/- key

⑨ Infrared transmitter

⑩ I/ ¹ (On/Standby) key

⑪ USB key

This function is not provided in this projector.

⑫APA (Auto Pixel Alignment) key

Automatically adjusts a picture to its clearest while a signal is input from a computer.

For details, see “Smart APA” in “The SET SETTING Menu” on page 34.

⑬LENS key

This function is not provided in this projector.

14 KEYSTONE (Trapezoidal distortion correction) / TILT key

Adjusts the vertical trapezoidal distortion of the image. Pressing this key, the adjustment menu is displayed. Use the arrow keys (▲/▼/◄/►) for adjustment.

15 PIC MUTING key

Cuts off the picture. Press again to restore the picture.

16 AUDIO MUTING key

Cuts off the sound. Press again to restore the sound.

17FREEZE key

Freezes the projected picture. To cancel the frozen picture, press the key again. This function is available when the PC signal is input.

Before using the Remote Commander

Pull out the clear film from the lithium battery holder.

To replace a battery

1. Pull out the battery cover by inserting a thin stick into the hole, as shown in the illustration.

2. Install the lithium battery.

3. Put the lithium battery holder back into the Remote Commander.

Notes on the lithium battery

• A button-type lithium battery (CR2025) is used in the Remote Commander. Do not use batteries other than CR2025.
• Keep the lithium battery out of the reach of children.
• Should the battery be swallowed, immediately consult a doctor.

Notes on Remote Commander operation

• Make sure that nothing obstructs the infrared beam between the Remote Commander and the remote control detector on the projector. Aim the Remote Commander at the front of the remote control detector or the screen.
• The operation range is limited. The shorter the distance between the Remote Commander and the remote control detector is, the wider the angle within which the commander can control the projector becomes.

Installing the Projector

This unit can be operated on a floor or desktop (floor installation), but also can be suspended from a ceiling with a dedicated mounting device (ceiling installation).

For details, see “Installation Diagram” on page 53.

Connecting the Projector

When you connect the projector, make sure to:

• Turn off all equipment before making any connections.
• Use the proper cables for each connection.
• Insert the cable plugs firmly; loose connections may increase noise and reduce performance of picture signals. When pulling out a cable, be sure to pull it out by the plug, not the cable itself.

Connecting a Computer

This section describes how to connect the projector to a computer.

For more information, refer to the computer's instruction manual.

To connect a computer

①HD D-sub 15-pin cable (supplied) ②Stereo audio connecting cable (not supplied) (Use a no-resistance cable.)

Notes

• For stereo audio connection, connect the stereo audio connecting cable to following connectors: VPL-EX70/EX7: AUDIO INPUT connector VPL-EW7: INPUT A AUDIO connector
• The projector accepts VGA, SVGA, XGA, SXGA, SXGA+, WXGA signals. However, we recommend that you set the output mode of your computer to WXGA (VPL-EW7) or XGA (VPL-EX70/EX7) mode for the external monitor.
• If you set your computer, such as a notebook computer, to output the signal to both your computer's display and the external monitor,

the picture of the external monitor may not appear properly. Set your computer to output the signal to only the external monitor.

For details, refer to the operating instructions supplied with your computer.

Note

To connect a Macintosh computer equipped with a video output connector of a type having two rows of pins, use a commercially available plug adaptor.

To connect a computer (Digital) or video equipment (Digital) (VPL-EW7 only)

①HDMI-DVI-D cable (not supplied) ②HDMI cable (not supplied)

Notes

• Be sure to use the HDMI cable with an HDMI logo.
• The HDMI connector of this projector is not compatible with DSD (Direct Stream Digital) Signal or CEC (Consumer Electronics control) Signal.

Connecting a VCR

This section describes how to connect the projector to a VCR.

For more information, refer to the instruction manuals of the equipment you are connecting.

To connect to a video or S video output connector

①Stereo audio connecting cable (not supplied) (Use a no-resistance cable.)

②Video cable (not supplied) or S-Video cable (not supplied)

Note

For stereo audio connection, connect the stereo audio connecting cable to following connectors:

VPL-EX70/EX7: AUDIO INPUT connector

VPL-EW7: VIDEO IN AUDIO connector

To connect to a video GBR/Component output connector

①Signal Cable (not supplied) HD D-sub 15-pin (male) ↔ 3 × phono jack

②Stereo audio connecting cable (not supplied) (Use a no-resistance cable.)

Notes

VPL-EX70/EX7: AUDIO INPUT connector VPL-EW7: INPUT A AUDIO connector

- For stereo audio connection, connect the stereo audio connecting cable to following connectors:

- Set the aspect ratio using "Aspect" on the INPUT SETTING menu according to the input signal.

- When you connect the projector to a video GBR output connector, select "Video GBR" or when you connect the projector to a component output connector, select "Component" with the "Input-A Signal Sel." setting on the SET SETTING menu.

Projecting

1 Plug the AC power cord into a wall outlet, and connect all equipment, then remove the lens cover.

The I/⏻ key lights in red and the projector goes into standby mode.

2 Press the I/⏻ key.

The I/⏻ key lights after flashing in green. (The projector cannot be used while the I/⏻ key is flashing.)

3 Turn on the equipment connected to the projector.

4 Press the INPUT key to select the input source.

Each time you press the key, the input signal switches as follows:

To input from Press INPUT	to display
Computer/Component connected to the INPUT A connector	Input-A
Computer connected to the INPUT B connector (VPL-EX70 only)	Input-B
Computer/VCR, etc. connected to INPUT B (Digital) connector (VPL-EW7 only)
Video equipment connected to the VIDEO input connector	Video
Video equipment connected to the S VIDEO input connector	S-Video

Smart APA (Auto Pixel Alignment) adjusts the picture of the connected equipment so that it is projected clearly.

Notes

- If “Auto Input Search” is set to “On,” the projector searches for the signals from the connected equipment and displays the input channel where the input signals are found.

For details, see "Auto Input Search" on page 34.

- The Smart APA feature is effective for the input analog signal from a computer only.

5 Switch the equipment connected to output to the projector.

Depending on the type of your computer, for example a notebook, or an all-in-one LCD type, you may have to switch the computer to output to the projector by pressing certain keys (e.g., LCD/VGA, □/□, etc.), or by changing your computer's settings.

Note

The key used for switching the computer to output to the projector varies depending on the type of computer.

6 Adjust the upper or lower position of the picture.

Use the adjuster to adjust the picture position.

Using the adjuster

Lift the projector while pressing the adjuster adjustment button, and adjust the tilt of the projector, then release the button to lock the adjuster.

Notes

- Be careful not to let the projector down on your fingers.

- Do not push hard on the top of the projector or do not drag it hard with the adjuster out. It may cause malfunction.

7 Adjust the trapezoidal distortion ( ) of the picture. (VPL-EX7 only)

Press the KEYSTONE key on the Remote Commander to display the adjustment menu and adjust the tilt using the ▲/▼/◄/► keys.

For VPL-EX70/EW7

• When you adjust the tilt of the projector with the adjuster, the V keystone adjustment is performed at the same time. If you do not want to perform the automatic keystone adjustment, set the “V Keystone” to “Manual.” (See page 37.)
• If you set the “V Keystone” to “Auto,” the “V Keystone” correction is automatically adjusted. However, it may not be perfectly adjusted depending on the room temperature or the screen angle. In this case, adjust it manually. Press the KEYSTONE key to “V Keystone” displays on the screen, and adjust the value with the ▲/▼/◄/► keys.

8 Adjust the size of the picture and the focus.

Adjust the picture size using the Zoom ring and adjust the picture focus using the Focus ring.

Turning Off the Power

1 Press the I/⏻ key.

“POWER OFF? Please press I/ ^① key again.” appears to confirm that you want to turn off the power.

Note

The message disappears if you press any key other than the I/⏻ key, or if you do not press any key for five seconds.

2 Press the I/⏻ key again.

The I/⏻ key flashes in green and the fan continues to run to reduce the internal heat. Also, the I/⏻ key flashes quickly for the first 60 seconds. During this time, you will not be able to light up the I/⏻ key again with the I/⏻ key.

3 Unplug the AC power cord from the wall outlet after the fan stops running and the I/⏻ key lights in red. (Except when using the Direct Power On/Off function or the Off & Go function.)

Selecting the Menu Language

You can select one of several languages for displaying the menu and other on-screen displays. The factory setting is English. To change the menu language, proceed as follows:

1 Plug the AC power cord into a wall outlet. 2 Press the I/⏻ key to turn on the projector. 3 Press the MENU key. The menu appears.

The menu currently selected is shown as a yellow button.

4 Press the ▲ or ▼ key to select the MENU SETTING menu, then press the ▶ or ENTER key. The selected menu appears.

5 Press the ▲ or ▼ key to select "Language," then press the ▶ or ENTER key.

6 Press the ▲, ▶, ◀ or ▼ key to select a language, then press the ENTER key. The menu changes to the selected language.

To clear the menu

Press the MENU key.

The menu disappears automatically if a key is not pressed for one minute.

Security Lock

The projector is equipped with a security lock function. When you turn the power of the projector on, you are required to input the previously set password. If you do not input the correct password, you will not be able to project the picture.

Notes

• You will not be able to use the projector if you forget your password and the password administrator is not available. Please be aware that using the security lock can prevent valid usage in such cases.
• When you set the security lock being active, the password will be necessary only when the power is turned on after plugging the power cord.

To use the security lock

1 Press the MENU key and then, on the INSTALL SETTING menu, turn on the "Security Lock" setting. 2 Enter the password.

Use the MENU, ▲/▼/◄/►, and ENTER keys to enter the four-digit password. (The default initial password setting is "ENTER, ENTER, ENTER, ENTER." After this is entered you can put in your own password. Therefore, when you use this function for the first time, please input "ENTER" four times.)

Next, the screen for entering the new password is displayed.

(Enter the password on this screen even if you want to keep the current password.)

Enter the password on this screen.

3 Enter the password again to confirm.

When the following message is displayed, the setting for security lock is completed.

Security Lock enabled!

If "Invalid Password!" is displayed on the screen, perform this procedure again from step 1.

Invalid Password!

4 Turn the main power off and disconnect the AC power cord. The security lock is set to on, then it becomes effective. The screen used for entering the password is displayed when the power is turned on the next time.

Security certification

When the password screen is displayed, enter the password that was set. If you fail to enter the correct password after three times, the projector cannot be used. In this case, press the I/↓ key to turn off the power.

To cancel the security lock

1 Press the MENU key, then turn off the "Security Lock" setting on the INSTALL SETTING menu.

2 Enter the password. Enter the password that was set.

Note

If you call the customer service center because you have forgotten the password, you will need to be able to verify the projector's serial number and your identity. (This process may differ in other countries/regions.) Once your identity has been confirmed, we will provide you with the password.

Other Functions

Direct Power On/Off Function

If you will be using a circuit breaker to turn the power for the entire system on and off, set the direct power on function to "On." You can turn the power on/off without pressing the power key on the projector.

Off & Go Function

If you are leaving the conference room immediately, turn the projector off, and then, you can unplug the AC power cord.

Note

When you restart the power immediately after turning it off using the Off & Go function, the power may not come back on. In that case, wait a few minutes and turn on the power again.

Effective Tools for Your Presentation

To enlarge the image (Digital Zoom function)

You can select a section of the image to enlarge. This function works when a signal from a computer is input.

This function does not work when a video signal is input.

1 Project a normal image, and press the D ZOOM + key on the Remote Commander.

The digital zoom icon appears in the center of the image.

2 Move the icon to the point on the image you want to enlarge. Use the arrow key (▲/▼/◄/►) to move the icon.

3 Press the D ZOOM + key again.

The portion of the image where the icon is located is enlarged. The enlargement ratio is displayed on the screen for a few seconds. By pressing the + key repeatedly, the image size (ratio of enlargement: max. 4 times) increases.

Use the arrow key (▲/▼/◄/►) to scroll the enlarged image.

To return the image to its original size

Press the D ZOOM - key.

Just pressing the RESET key returns the image back to its original size immediately.

To freeze the image projected (Freeze function)

Press the FREEZE key. "Freeze" appears when the key is pressed. This function works when a signal from a computer is input. To restore the original screen, press the FREEZE key again.

Adjustments and Settings Using a Menu

Using a MENU

The projector is equipped with an on-screen menu for making various adjustments and settings.

Display items

Input signal indicator

Input signal setting indicator

Picture adjustment menu

Input signal indicator

Shows the selected input channel. x displayed when no signal is input. You can hide this indicator using "Status" on the MENU SETTING menu.

Input signal setting indicator

For Input-A: Shows "Auto" or "Input-A Signal Sel." setting on the SET SETTING menu.

For Video/S-Video input: Shows "Auto" or the "Color System" setting on the SET SETTING menu.

1 Press the MENU key.

The menu appears.

The menu presently selected is shown as a yellow button in the column on the left.

2 Use the ▲ or ▼ key to select a menu, then press the ▶ or ENTER key. The selected menu appears.

3 Select an item.

Use the ▲ or ▼ key to select the item, then press the ▶ or ENTER key. The setting items are displayed in a pop-up menu or in a sub menu.

Pop-up menu

Sub menu

Menu Setting items

4 Make the setting or adjustment of an item.

- When changing the adjustment level: To increase the number, press the ▲ or ▶ key. To decrease the number, press the ▼ or ◀ key. Press the ENTER key to restore the previous screen.

- When changing the setting: Press the ▲ or ▼ key to change the setting. Press the ENTER or ◀ key to restore the previous screen.

To clear the menu

Press the MENU key.

The menu disappears automatically if a key is not pressed for one minute.

To reset items that have been adjusted

Select the item that you want to reset, and then press the RESET key on the Remote Commander.

“Complete!” appears on the screen and the setting of the item that you have selected is reset to its factory preset value.

Items that can be reset are:

• “Contrast,” “Brightness,” “Color,” “Hue” and “Sharpness” on the “Adjust Picture...” menu of the PICTURE SETTING menu
• “Dot Phase,” “H Size,” and “Shift” on the “Adjust Signal...” menu of the INPUT SETTING menu

Storage of the settings

The settings are automatically stored in the projector memory when the ENTER key is pressed.

If no signal is input

If there is no input signal, “Cannot adjust this item.” appears on the screen.

Unadjustable items

Items that cannot be adjusted, depending on the input signal, are not displayed on the menu.

For details, see page 40.

The PICTURE SETTING Menu

The PICTURE SETTING menu is used for adjusting the picture or volume. Items that can be adjusted or set depend on the kind of input signals.

For details, see "Input signals and adjustable/setting items" on page 40.

Setting items Functions Initial setting
Picture Mode Selects the picture mode.• Dynamic: Emphasizes the contrast to produce a “dynamic” picture.• Standard: Selects for the standard picture.• Game: Select for viewing game picture.• Living: Select for viewing sports, music, digital video camera picture.• Cinema: Select for viewing film-like picture.• Presentation: Makes the picture suitably bright for a presentation when the signal is input from a computer.		Set according to the input signal
Adjust Picture... The unit can store the setting values of the following sub menu items for each picture mode separately.
Contrast Adjusts the picture contrast. 80
Brightness Adjusts the picture brightness. 50
Color Adjusts color intensity. 50
Hue	Adjusts color tones. The higher the setting, the more greenish the picture becomes. The lower the setting, the more purplish the picture becomes.	50
Sharpness	Adjusts the picture sharpness. The higher the setting, the sharper the picture becomes. The lower the setting, the softer the picture becomes.	30
Gamma Mode	Selects a gamma correction curve.• Graphics: Improves the reproduction of halftones. Photos can be reproduced in natural tones.• Text: Contrasts black and white. Suitable for images that contain lots of text.	Graphics

Contrast Adjusts	the picture contrast. 80
Brightness Adjusts	the picture brightness. 50
Color Adjusts color intensity.	50
Hue	Adjusts color tones. The higher the setting, the more greenish the picture becomes. The lower the setting, the more purplish the picture becomes.	50
Sharpness	Adjusts the picture sharpness. The higher the setting, the sharper the picture becomes. The lower the setting, the softer the picture becomes.	30
Gamma Mode	Selects a gamma correction curve.• Graphics: Improves the reproduction of halftones. Photos can be reproduced in natural tones.• Text: Contrasts black and white. Suitable for images that contain lots of text.	Graphics
Setting items Functions Initial setting
	Color Temp. Adjusts the color temperature.High: Makes white colors bluish.Middle: Makes white part of the picture natural white.Low: Makes white colors reddish.	Set according to the input signal
	DDE (Dynamic Detail Enhancer)	Selects the mode to play the input video signal according to the material.Off: Plays back the interlace format without conversion.Progressive: Plays back the video picture of the interlace format converting to progressive.Film: Plays back a smooth picture in a software of 2-2, 2-3 pull-down type like a movie. When other than the software of 2-2, 2-3 pull-down type is played back, it is automatically switched to "Progressive".
Volume Adjusts the volume. 30

The INPUT SETTING Menu

The INPUT SETTING menu is used to adjust the input signal.

When the signal is input from a computer

Setting items Functions Initial setting
Adjust Signal...
	Dot Phase Adjusts the dot phase of the LCD panel and the signal output from a computer.Adjust the picture further for finer picture after the picture is adjusted by pressing the APA key.	Set according to the input signal
	H Size Adjusts the horizontal size of a picture output from a computer.Adjust the setting according to the dots of the input signal.For details, see page 51.	Set according to the input signal
	Shift Adjusts the position of the picture.H adjusts the horizontal position of the picture.V adjusts the vertical position of the picture.As the setting for H increases, the picture moves to the right, and as the setting decreases, the picture moves to the left.As the setting for V increases, the picture moves up, and as the setting decreases, the picture moves down.Use the ◀ or the ▶ key to adjust the horizontal position and the ▲ and ▼ key for the vertical position.	Set according to the input signal
Aspect (When the video signal is input)		You can set the aspect ratio of the picture to be displayed for the current input signal. This item is enabled only when an video signal (preset memory numbers 1 to 11) is input.Normal*1: Select to view a picture with normal 4:3 aspect ratio.4:3*2: Makes the aspect ratio 4:3.16:9*2: Select to view a picture squeezed.Full*1: Select to view a picture of 16:9 or of 4:3 squeezed.Zoom: Select to enlarge the original picture without distorting the aspect ratio.Wide Zoom*1: Select to enlarge a picture with minimum distortion.
Aspect (When the PC signal is input)	You can set the aspect ratio of the picture to be displayed for the current input signal. This item is enabled only when an PC signal (preset memory numbers 21 to 63) is input.Full 1: Displays a picture vertically or horizontally to fill the screen without changing the aspect ratio of the original picture.Full 2: The original image is projected fully in the window.Full 3*1 : Displays a 1280 × 800 dot picture on the screen without changing the aspect ratio of the original picture.Normal: Displays the picture while matching one pixel of input picture element to that of the LCD. The picture will be clear but the picture size will be smaller.Zoom *1 : Select to enlarge the original picture without distorting the aspect ratio.	Set according to the input signal
Over Scan *1	Hides the outer edges of the picture.On: Hides the outer edges of the input picture. Select this setting when noise appears along the edge of the picture.Off: Projects the whole of the input picture.	On

*1: VPL-EW7 only *2: VPL-EX70/EX7 only

Notes

• For Aspect, some of the “Aspect” setting items are not displayed on the screen according to the input signal.
• Note that if the projector is used for profit or for public viewing, modifying the original picture by switching to the wide mode may constitute an infringement of the rights of authors or producers, which are legally protected.

About the Preset Memory No.

This projector has 45 types of preset data for input signals (the preset memory). When a preset signal is input, the projector automatically detects the signal type and recalls the data for the signal from the preset memory to adjust it to an optimum picture. The memory number and signal type of that signal are displayed on the INFORMATION menu (See page 39). You can also adjust the preset data through the INPUT SETTING menu.

See the chart on page 51 to find if the signal is registered in the preset memory.

Note

When the aspect ratio of input signal is other than “Full 2”, a part of the screen may be displayed in black.

The SET SETTING Menu

The SET SETTING menu is used for changing the settings of the projector.

Setting items Functions Initial setting
Smart APA The APA	(Auto Pixel Alignment) automatically adjusts “Dot Phase,” “H Size” and “Shift” on the INPUT SETTING menu for the input signal from a computer.On:When a signal is input from a computer, the APA functions automatically so that the picture can be seen clearly. You can adjust the picture by pressing the APA key on the Remote Commander even if “Smart APA” set to “On.”Off:The APA functions when you press the APA key on the Remote Commander.	On
Auto Input Search W	When set to “On,” the projector detects input signals in the following order: Input-A/Input-B (VPL-EX70/EW7 only)/Video/S-Video. It indicates the input channel when the power is turned on or the INPUT key is pressed.	Off
Input-A Signal Sel. S	Selects the type of signal input from the equipment connected to the INPUT A connector.Selects the type of signal input from the equipment by selecting “Input-A” with the INPUT key.Auto: Selects the input signal type automatically.Computer: Inputs the signal from a computer.Component: Inputs the component signal from a DVD player/recorder, Blu-ray Disc player, digital tuner, etc.Video GBR: Inputs the signal from a TV game or HDTV broadcast.	Auto
Color System Selects	the color system of the input signal.If you select “Auto,” the projector detects the color system of the input signal automatically. If the picture is distorted or colorless, select the color system according to the input signal.	Auto
Power Saving Selects	the Power Saving mode.Lamp off:The lamp goes off if no signal is input for 10 minutes. The lamp lights again when a signal is input or any key is pressed.Standby:The projector goes into Standby mode if no signal is input for 10 minutes. To use it, turn on the power again.Off:The projector does not go into Power Saving mode.	Off
Panel Key Lock Locks	all the control panel keys on the top panel of the projector so that the projector can be operated only with the Remote Commander.To lock the control panel keys, set to “On.”When it is set to “On,” keeping the I/⏻ key on the control panel pressed for 10 seconds turns the projector on when it is in standby mode, and turns the projector to standby mode when the power is on.If you press and hold the MENU key for about 10 seconds when the power is on, the lock will be released and “Panel Key Lock” is automatically set to “Off.”	Off
CC Display Turns on	or off the Closed Captions (CC) function.Off:Turns off the Closed Captions (CC) function.CC1/CC2/CC3/CC4/TEXT1/TEXT2/TEXT3/TEXT4:Selects a displayed version of the dialogue or sound channel of a program.	Off
Lamp Timer Reset W	When replacing the lamps, reset the lamp timer. –

Notes

- Press the APA key when the full image is displayed on the screen. If the projected image includes a black portion around it, the APA function will not work properly and some parts of the image may not be displayed on the screen.

• You can cancel the adjustment by pressing the APA key again while “Adjusting” appears on the screen.
• The picture may not be adjusted properly depending on the type of input signal.
• Adjust the “Dot Phase,” “H Size,” and “Shift” items on the INPUT SETTING menu when you adjust the picture manually.
• If the input signal is not displayed correctly when the input A signal classifying is set to “Auto”, set it to conform to the input signal.
• Closed Captioning is not displayed in the following cases:

- while you are adjusting the volume with VOLUME +/- on the remote commander

• - while you are operating on-screen menus
• - while “Please replace the Lamp.” is displayed on the screen

The MENU SETTING Menu

The MENU SETTING menu is used for changing the menu displays.

Setting items Functions Initial setting
Status (on-screen display)	Sets up the on-screen display.When set to “Off,” turns off the on-screen displays except for the menus, a message when the power is turned off, and warning messages.	On
Language Selects the	language used in the menu and on-screen displays. Use the ▲/▼/◄/► keys to select the display language, and press the ENTER key.	English
Menu Position Selects	the display position of the menu from “Top Left,” “Bottom Left,” “Center,” “Top Right,” and “Bottom Right.”	Center
Start Up Image	• On: Displays the Start Up Image in the window after turning on the power.• Off: Does not displays the Start Up Image in the window after turning on the power.	On

The INSTALL SETTING Menu

The INSTALL SETTING menu is used for changing the settings of the projector.

Setting items Functions Initial setting
V Keystone (VPL-EX70/ EW7 only)	Corrects the trapezoidal distortion caused by the projection angle. Select “Auto” for automatic correction, or “Manual” for manual correction using the ▲/▼/◄/► keys.When the bottom of the trapezoid is longer than the top□ : Sets a lower value.When the top of the trapezoid is longer than the bottom□ : Sets a higher value.	Auto
V Keystone (VPL-EX7 only)	Corrects the trapezoidal distortion caused by the projection angle using the ▲/▼/◄/► keys on the Remote Commander.When the bottom of the trapezoid is longer than the top□ : Sets a lower value.When the top of the trapezoid is longer than the bottom□ : Sets a higher value.	0
Image Flip Flips the image on the screen horizontally and/or vertically.• HV: Flips the image horizontally and vertically.• H: Flips the image horizontally.• V: Flips the image vertically.• Off: The image does not flip.		Off
Background Selects the background color of the screen when no signal is input to the projector. Select “Black” or “Blue.” Normally, set to “Blue.”		Blue
Lamp Mode	Sets the lamp brightness used during the projection.• High: Illuminates the projected image brightly.• Standard: Reduces fan noise and power consumption.The brightness of the projected image will be lower compared with the “High” setting.	Standard
High Altitude Mode	Set to “On” when the projector is used at an altitude of 1,500 m or higher.	Off
Security Lock	Turns on the projector’s security lock function.When set to “On,” turns on the security lock function, which locks the projector once a password has been set.For details, see “Security Lock” on page 25.	Off
Direct Power On	Set to “On” if you are using a circuit breaker to turn the power on/off the entire system. You can turn the power on/off without pressing the power key on the projector.	Off
Standby Mode	Lowers the power consumption in Standby Mode.Select “Low” to lower power consumption during standby.	Low

Notes

• The picture quality may deteriorate when the V Keystone function is used, because it is an electrical correction.
• If you set “High Altitude Mode” to “On” at an altitude of under 1,500 m, the reliability of the lamp may be reduced.

Notes on VPL-EX70/EW7

• The auto V Keystone adjustment may not correct the trapezoidal distortion perfectly, depending on the room temperature or the screen angle.
• If you need fine adjustment when V Keystone is set to “Auto”, press the KEYSTONE key on the control panel or the remote commander, and change the value. The setting mode will be temporarily changed to “Manual” from “Auto”. If you want to restore the “Auto” setting, first switch the V Keystone setting to “Manual”, then return it to “Auto”.
• When you want to apply the fine adjustment value the next time, change the V Keystone setting to “Manual” from “Auto”.

The INFORMATION Menu

The INFORMATION menu displays the model name, serial number, the horizontal and vertical frequencies of the input signal and the cumulated hours of usage of the lamp.

Setting items Functions

fH Displays the horizontal frequency of the input signal.The displayed value is approximate.

fV Displays the vertical frequency of the input signal.The displayed value is approximate.

Lamp Timer Indicates how long the lamp has been turned on.

Note

These are only displayed on the screen. You cannot alter the display, and there is no setting to be altered.

Input signals and adjustable/setting items

Some of the items in the menus cannot be adjusted depending on the input signal as indicated in the following tables.

The items that cannot be adjusted are not displayed in the menu.

PICTURE SETTING menu

Item Input signal
		Video or S-Video (Y/C)	Component Video	GBR Computer HDMI
Picture Mode		●	●		●	●
Adjust Picture...
	Contrast	●	●		●	●
	Brightness	●	●		●	●
	Color	●	●		●	- ●
	Hue ●	(NTSC 3.58/4.43 only)	●	●	-	-
	Sharpness	●	●		●	- ●
	Gamma Mode	-	-		-	● -
	Color Temp.	●	●		● *2	●
	DDE	●	●(Interlace format only)*1	●(Interlace format only)*1	- ●	(Interlace format only)*1
Volume		●	●		●	●

● : Adjustable/can be set - : Not adjustable/cannot be set *1: Except for preset memory No. 7, 8 *2: Cannot be set in the Presentation mode

INPUT SETTING menu

Item Input signal
		Video/S-Video (Y/C)	Component Video	GBR Computer HDMI
Aspect		●	●		●*3	●
Adjust Signal...
	Dot Phase	-	-		-	●-
	H size	-	-		-	●-
	Shift	-●	●	●	-
Over Scan		-●	●	-●

● : Adjustable/can be set - : Not adjustable/cannot be set *3: Can be set except preset memory number 49.

Replacing the Lamp

The lamp used as a light source is a consumable product. Thus, replace the lamp with a new one in the following cases.

• When the lamp has burnt out or dims
• “Please replace the Lamp.” appears on the screen • The LAMP/COVER indicator lights up (repeats flashing three times)

The lamp life varies depending on conditions of use.

Use an LMP-E191 Projector Lamp as the replacement lamp.

Use of any other lamps than the LMP-E191 may cause damage to the projector.

Notes

• If the lamp breaks, ask qualified Sony personnel to replace the lamp and to check inside. • Pull out the lamp by holding the handle.
• When removing the lamp, make sure it remains horizontal, then pull straight up. Do not tilt the lamp. If you pull out the lamp while it is tilted and if the lamp breaks.

1 Turn off the projector, and disconnect the AC power cord from the AC outlet.

Note

When replacing the lamp after using the projector, wait for at least an hour for the lamp to cool.

2 Place a protective sheet (cloth) beneath the projector. Turn the projector over so you can see its underside.

Note

Be sure that the projector is stable after turning it over.

3 Open the lamp cover by loosening the screw with a Phillips screwdriver.

Note

For safety reasons, do not loosen any other screws.

4 Loosen the two screws on the lamp unit with the Phillips screwdriver (1). Fold out the handle (2), then pull out the lamp unit by the handle (3).

5 Insert the new lamp all the way in until it is securely in place (1). Tighten the two screws (2). Fold down the handle to replace it (3).

Notes

• Be careful not to touch the glass surface of the lamp.
• The power will not turn on if the lamp is not secured properly.
• Do not allow any liquid or other objects into the slot to avoid electrical shock or fire.

6 Close the lamp cover and tighten the screw.

Note

Be sure to attach the lamp cover securely as it was. If not, the projector cannot be turned on.

7 Turn the projector back over. 8 Connect the power cord. The I/⏻ key lights in red. 9 Press the I/⏻ key to turn the projector on. 10 Press the MENU key, and then select the SET SETTING menu.

11 Select "Lamp Timer Reset", and then press the ENTER key.

12 Select "Execute" with the ▼ key, and then press the ENTER key.

The Lamp Timer is initialized to 0, and "Change the Lamp and clean the Filter?" is displayed in the menu screen.

Change the Lamp and clean the Filter?

Yes: + No: ↓

Refer to page 43 for "Cleaning the Air Filter".

13 Select "Yes" with the ▲ key. "Lamp Timer Reset Complete!" is displayed in the menu screen.

Disposal of the used lamp For the customers in the USA (VPL-EW7 only)

Lamp in this product contains mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance (www.eiae.org).

Cleaning the Air Filter

The air filter should be cleaned whenever you replace the lamp. Remove the air filter, and then remove the dust with a vacuum cleaner.

The time needed to clean the air filter will vary depending on the environment or how the projector is used.

When it becomes difficult to remove the dust from the filter with a vacuum cleaner, remove the air filter and wash it.

1 Turn the power off and unplug the power cord.

2 Draw out the air filter cover and remove it.

3 Remove the air filter.

4 Wash the air filter with a mild detergent solution and dry it in a shaded place.

5 Attach the air filter so that it fits into the each claws on the air filter cover and replace the cover.

Notes

- If you neglect to clean the air filter, dust may accumulate, clogging it. As a result, the temperature may rise inside the unit, leading to a possible malfunction or fire.

- Be sure to attach the air filter cover firmly; the power can not be turned on if it is not closed securely.

- The air filter has a face and a reverse side. Place the air filter so that it fits in a notch on the air filter cover.

Troubleshooting

If the projector appears to be operating erratically, try to diagnose and correct the problem using the following instructions. If the problem persists, consult with qualified Sony personnel.

Power

Symptom Cause and Remedy
The power is not turned on.	The power has been turned off and on with the I/1 key at a short interval.Wait for about 90 seconds before turning on the power (see page 23).The lamp cover is not secured.Close the lamp cover securely (see page 42).The air filter cover is detached.Attach the air filter cover securely (see page 43).

Picture

Symptom Cause and Remedy
No picture. • A cable is disconnected or the connections are wrong.→ Check that the proper connections have been made (see page 18).• The connections are wrong.→ This projector is compatible with DDC2B (Digital Data Channel 2B). If your computer is compatible with DDC, turn the projector on according to the following procedures.1 Connect the projector to the computer.2 Turn the projector on.3 Start the computer.• Input selection is incorrect.→ Select the input source correctly (see page 22).• The picture is muted.→ Press the PIC MUTING key to release the picture muting (see page 17).• The computer signal is not set to output to an external monitor or set to output both to an external monitor and a LCD monitor of a computer.→ Set the computer signal to output only to an external monitor (see page 18).
The picture is noisy. Noise may appear on the background depending on the combination of the number of dots input from the computer and the numbers of pixels on the LCD panel.→ Change the desktop pattern on the connected computer.
The picture from the INPUT A connector is colored strangely.	The input signal cannot be received at “Auto” of “Input-A Signal Sel” on the SET SETTING menu, or the setting of “Input-A Signal Sel” is incorrect.→ Selects “Computer”, “Video GBR” or “Component” correctly according to the input signal (see page 34).
On-screen display does not appear.	“Status” on the MENU SETTING menu has been set to “Off.”→ Set “Status” on the MENU SETTING menu to “On” (see page 36).
Color balance is incorrect. •	The picture has not been adjusted properly.→ Adjust the picture (see page 30).• The projector is set to the wrong color system.→ Set “Color System” on the SET SETTING menu to match the color system being input (see page 34).
The picture is too dark. • Contrast or brightness has not been adjusted properly.→ Adjust the contrast or brightness on the “Adjust Picture...” menu properly (see page 30).• The lamp has burnt out or is dim.→ Replace the lamp with a new one (see page 41).
The picture is not clear. • The picture is out of focus.→ Adjust the focus (see page 23).• Condensation has accumulated on the lens.→ Leave the projector for about two hours with the power on.
The image extends beyond the screen.	• The APA key has been pressed even though there are black edges around the image.→ Display the full image on the screen and press the APA key.→ Adjust “Shift” on the INPUT SETTING menu properly (see page 32).• This input signal cannot be projected as the frequency is out of the acceptable range of the projector.→ Input a signal that is within the range of the frequency.• The resolution setting of the output signal of the computer is too high.→ Set the output setting to WXGA (VPL-EW7) or XGA (VPL-EX70/EX7) (see page 19).
The picture flickers. “Dot Phase” on the INPUT SETTING menu has not been adjusted properly.→ Adjust “Dot Phase” on the INPUT SETTING menu properly (see page 32).

Sound

Symptom Cause and Remedy
No sound. • A cable is disconnected or the connections are wrong.→ Check that the proper connections have been made (see page 18).• The audio connecting cable used is incorrect.→ Use a no-resistance stereo audio cable (see page 19).• The sound is not adjusted properly.→ Adjust the sound with the VOLUME +/- key on the Remote Commander or adjust “Volume” on the PICTURE SETTING menu (see page 31).

Remote Commander

Symptom Cause and Remedy
The Remote Commander does not work.	The Remote Commander battery are dead.→ Replace them with new battery (see page 17).

Others

Symptom Cause and Remedy
The control panel keys do not function.	The control panel keys are locked.→ Unlock the control panel keys (see page 35).

Indicators

Symptom Cause and Remedy
The LAMP/COVER indicator flashes in orange. (Repetition rate of 2 flashes)	The lamp cover or the air filter cover is detached.→ Attach the cover securely (see pages 42 and 43).
The LAMP/COVER indicator flashes in orange. (Repetition rate of 3 flashes)	· The lamp has reached the end of its life.→ Replace the lamp (see page 41).· The lamp has reached a high temperature.→ Wait for 60 seconds to cool the lamp and then turn on the power again.
I/⏻ key flashes in red. (Repetition rate of 2 flashes)	· The internal temperature is unusually high.→ Check to see that nothing is blocking the ventilation holes.· The projector is being used at a high altitude.→ Ensure that “High Altitude Mode” in the INSTALL SETTING menu is set to “On.”
I/⏻ key flashes in red. (Repetition rate of 4 flashes)	The fan is broken.→ Consult with qualified Sony personnel.
I/⏻ key flashes in red. (Repetition rate of 6 flashes)	Unplug the AC power cord from the wall outlet after the I/⏻ key stops flashing, plug the power cord to the wall outlet, and then turn the projector on again. If the ON/STANDBY flashes in red and the problem persists, the electrical system has failed.→ Consult with qualified Sony personnel.

Messages List

Warning Messages

Use the list below to check the meaning of the messages displayed on the screen.

Message Meaning and Remedy
Please replace the Lamp and clean the Filter.	It is time to replace the lamp and clean the air filter. → Replace the lamp (see page 41) and clean the filter (see page 43).When this message appears even after replacing the lamp, the task has not been completed. → Perform the operation of steps 10 to 13 on page 42.

Caution Messages

Use the list below to check the meaning of the messages displayed on the screen.

Message Meaning and Remedy
Not applicable! You have pressed the wrong key.→Press the appropriate key.
The panel keys are locked! “Panel Key Lock” on the SET SETTING menu is set to “On.”→All the keys on the control panel of the projector are locked.Operate the projector with the keys on the Remote Commander (see page 35).

Specifications

Optical characteristics

Projection system

3 LCD panels, 1 lens, projection system

LCD panel VPL-EX70/EX7: 0.63-inch

(16.0 mm) XGA panel, about 2,360,000 pixels (1024 × 768 × 3)

VPL-EW7: 0.59-inch (15.0 mm)

WXGA panel, about 3,070,000 pixels (1280 × 800 × 3)

Lens 1.2 times zoom lens

f 18.53 to 22.18 mm/F1.65 to 1.93

Lamp 190 W Ultra high pressure lamp

Projected picture size

40 to 300 inches (1,016 to 7,620 mm)

Light output 1) VPL-EX70: 2600 lm

VPL-EX7/EW7: 2000 lm

1) When the Lamp Mode is set to "High."

Throwing distance (When placed on the floor. Adjuster not stretched, and the V Keystone function has been done.)

VPL-EX70/EX7

40-inch (1,016 mm): 1.1 to 1.4 m (3.6 to 4.6 feet)

80-inch (2,032 mm): 2.3 to 2.8 m (7.5 to 9.2 feet)

100-inch (2,540 mm): 2.9 to 3.5 m (9.5 to 11.5 feet)

150-inch (3,810 mm): 4.4 to 5.2 m (14.4 to 17.1 feet)

200-inch (5,080 mm): 5.8 to 7.0 m (19.0 to 23.0 feet)

250-inch (6,350 mm): 7.3 to 8.8 m (24.0 to 28.9 feet)

300-inch (7,620 mm): 8.8 to 10.5 m (28.9 to 34.5 feet)

VPL-EW7:

(When "Aspect" on the Signal menu is set to "Full 2")

40-inch (1,016 mm): 1.2 to 1.5 m (3.9 to 4.9 feet)

80-inch (2,032 mm): 2.5 to 2.9 m (8.2 to 9.5 feet)

100-inch (2,540 mm): 3.1 to 3.7 m (10.2 to 12.1 feet)

150-inch (3,810 mm): 4.6 to 5.6 m (15.1 to 18.4 feet)

200-inch (5,080 mm): 6.2 to 7.4 m (20.3 to 24.3 feet)

250-inch (6,350 mm): 7.7 to 9.3 m

(25.3 to 30.5 feet)

300-inch (7,620 mm): 9.3 to 11.1 m

(30.5 to 36.4 feet)

There may be a slight difference between the actual value and the design value shown above.

Electrical characteristics

Color system NTSC3.58/PAL/SECAM/

NTSC4.43/PAL-M/PAL-N/

PAL60 system, switched

automatically/manually

(NTSC4.43 is the color system

used when playing back a video

recorded in NTSC on a

NTSC4.43 system VCR.)

Resolution VPL-EX70/EX7: 750 horizontal

TV lines (Video input)

1024 × 768 dots (RGB input)

VPL-EW7: 750 horizontal TV lines (Video input)

1280 × 800 dots (RGB input)

Acceptable computer signals ²

fH: 19 to 92 kHz

fV: 48 to 92 Hz

(Maximum input signal resolution:

SXGA+ 1400 × 1050

fV: 60 Hz)

2) Set the resolution and the frequency of the signal of the connected computer within the range of acceptable preset signals of the projector.

Applicable video signals

15 k RGB/component 50/60 Hz,

Progressive component 50/60

Hz, DTV (480/60i, 575/50i,

480/60p, 575/50p, 720/60p,

720/50p, 1080/60i, 1080/50i),

Composite video, Y/C video

Speaker: Monaural speaker system, 40 ×

28.5 mm (1 5/8 × 1 1/8 inches)

Speaker output

1 W (max.) × 1

Input/Output

VIDEO IN VIDEO: phono type

Composite video: 1 Vp-p ±2 dB sync negative (75 ohms terminated)

S VIDEO: Y/C mini DIN 4-pin type

Y (luminance): 1 Vp-p ±2 dB

sync negative (75 ohms terminated)

C (chrominance): burst 0.286

Vp-p ±2 dB (NTSC) (75 ohms

terminated), burst 0.3 Vp-p ±2

dB (PAL) (75 ohms terminated)

AUDIO (VPL-EW7 only): Stereo minijack, 500 mVrms, input impedance 47 Kilohms or more

INPUT A RGB: HD D-sub 15-pin (female)

Analog RGB/component:

G: 0.7 Vp-p ±2 dB (75 ohms terminated)

G with sync/Y: 1 Vp-p ±2 dB sync negative (75 ohms terminated)

level, positive/negative

VD: Vertical sync input: TTL level, positive/negative

AUDIO (VPL-EW7 only): Stereo minijack, 500 mVrms, input impedance 47 Kilohms or more

INPUT B HDMI (VPL-EW7 only): Digital

RGB/Y CB (PB) CR (PR): HDMI

RGB (VPL-EX70 only): HD D-sub 15-pin (female) Analog RGB:

R: 0.7 Vp-p ±2 dB (75 ohms terminated)

G: 0.7 Vp-p ±2 dB (75 ohms terminated)

B: 0.7 Vp-p ±2 dB (75 ohms terminated)

HD: Horizontal sync input: TTL level, Positive/negative

VD: Vertical sync input: TTL level, positive/negative

AUDIO INPUT (VPL-EX70/EX7 only)

Stereo minijack, 500 mVrms, input impedance 47 Kilohms or more

OUTPUT MONITOR OUT: HD D-sub 15-pin (female)

R, G, B: Gain Unity: 75 ohms

HD, VD: 4 Vp-p (open), 1 Vp-p (75 ohms)

AUDIO OUT (variable out):

Stereo minijack

1 Vrms (when volume is at maximum and input signal is 500 mVrms), output impedance 5 kilohms or less

REMOTE RS-232C: D-sub 9 pin

General

Dimensions: Approx. 314 × 109 × 269 mm

(12 3/8 × 4 3/8 × 10 5/8 inches)

(w/h/d) (without projecting parts)

Mass VPL-EX70/EW7:

Approx. 3.0 kg (6 lb 10 oz)

VPL-EX7:

Approx. 2.9 kg (6 lb 6 oz)

Power requirements

AC 100 to 240 V, 2.6 to 1.1 A, 50/60 Hz

Power consumption

VPL-EX70/EX7: Max. 260 W

During standby (Standard): 3 W

During standby (Low): 1 W

VPL-EW7: Max. 270 W

During standby (Standard): 3 W

During standby (Low): 1 W

Heat dissipation

884 BTU (VPL-EX70/EX7)

921 BTU (VPL-EW7)

Operating temperature

0°C to 35°C (32°F to 95°F)

Operating humidity

35% to 85% (no condensation)

Storage temperature

-20°C to +60°C

(-4°F to +140°F)

Storage humidity

10% to 90%

Supplied accessories

Remote Commander (1)

Lithium battery CR2025 (1)

HD D-sub 15 pin cable (1.8 m) (1) (1-967-100-11/Sony)

Carrying case (1)

AC power cord (1)

Lens cap (1)

Operating Instructions (CD-ROM) (1)

Quick Reference Manual (1)

Security Label (1)

Design and specifications of the unit, including the optional accessories, are subject to change without notice.

Note

Always verify that the unit is operating properly before use. SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER DURING THE WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY OTHER REASON WHATSOEVER.

Optional accessories

Projector Lamp

LMP-E191 (for replacement)

Not all optional accessories are available in all countries.

Please check with your local Sony Authorized Dealer.

Pin assignment

INPUT A connector (HD D-sub 15-pin, female)

1	R /	R	- Ysupply inputfor DDC
2 G/Y 10 GND
3 B/B-Y 11 GND
4 RESERVE 12 DDC/SDA
5	G N	D	1
6	G N	D	( R
7 GND (G) 15 DDC/SCL
8	G N	D	( B

INPUT B connector (HD D-sub 15-pin, female) (VPL-EX70 only)

1	R	9	P o supply input for DDC
2 G	10 GND
3 B	11 GND
4 RESERVE 12 DDC/SDA
5	G N	D	1
6	G N	D	( R
7 GND (G)	15 DDC/SCL
8	G N	D	( B

RS-232C connector (D-sub 9 pin, female)

1	N	C		6	N	C
2	R	X	D	A	7	RT
3	T	X	DA	8	C	T
4	D	T	R	9	N	C
5 GND

9 Power

3 HD

) 1 4 VD

)

wer

Preset signals

Memory No.	Preset signal fH (kHz) fV (Hz) Sync
1 Video 60 Hz 60 Hz 15.734 59.940 –
2 Video 50 Hz 50 Hz 15.625 50.000 –
3 480/60i	480/60i 15.734 59.940 S on G/Y
4 575/50i	575/50i 15.625 50.000 S on G/Y
5 480/60p	480/60p (Progressive component NTSC)		31.470 60.000 S on G/Y
6 575/50p	575/50p (Progressive component PAL)		31.250 50.000 S on G/Y
7 1080/60i	1035/60i, 1080/60i	33.750 60.000 S on G/Y
8 1080/50i	1080/50i	28.130 50.000 S on G/Y
10	720/60p 720/60p	45.000	60.000 S on G/Y
11	720/50p 720/50p	37.500	50.000 S on G/Y
21	640 × 350	VGA mode 1	31.469	70.086	H-pos, V-neg
22		VGA VESA 85 Hz	37.861 85.00	80 H-pos, V-neg
23	640 × 400	PC-9801 Normal	24.823	56.416	H-neg, V-neg
24		VGA mode 2	31.469	70.086	H-neg, V-pos
25		VGA VESA 85 Hz	37.861 85.00	80 H-neg, V-pos
26	640 × 480	VGA mode 3	31.469	59.940	H-neg, V-neg
27		Macintosh 13"	35.000 66.60	67 H-neg, V-neg
28		VGA VESA 72 Hz	37.861 72.80	9 H-neg, V-neg
29		VGA VESA 75 Hz	37.500 75.00	00 H-neg V-neg
30		VGA VESA 85 Hz	43.269 85.00	08 H-neg V-neg
31	800 × 600	SVGA VESA 56 Hz	35.156	56.250	H-pos, V-pos
32		SVGA VESA 60 Hz	37.879	60.317	H-pos, V-pos
33		SVGA VESA 72 Hz	48.077	72.188	H-pos, V-pos
34		SVGA VESA 75 Hz	46.875	75.000	H-pos, V-pos
35		SVGA VESA 85 Hz	53.674	85.061	H-pos, V-pos
36	832 × 624	Macintosh 16"	49.724	74.550	H-neg, V-neg
37	1024 × 768	XGA VESA 60 Hz	48.363	60.004	H-neg, V-neg
38		XGA VESA 70 Hz	56.476 70.00	69 H-neg, V-neg
39		XGA VESA 75 Hz	60.023 75.00	29 H-pos, V-pos
40		XGA VESA 85 Hz	68.677 84.90	97 H-pos, V-pos
41	1152 × 864	SXGA VESA 70 Hz 63.995 70.019 H-pos, V-pos
42		SXGA VESA 75 Hz 67.500 75.000 H-pos, V-pos
43		SXGA VESA 85 Hz 77.487 85.057 H-pos, V-pos
44	1152 × 900	Sunmicro LO	61.795	65.960	H-neg, V-neg

Memory No.	Preset signal		fH (kHz)	fV (Hz) Sync
45 1280 ×	960 SXGA VES	A 60 Hz 60.000 60.000 H-	pos, V-pos
46 SXGA	VESA 75 Hz 75	000 75.000 H-pos, V-pos
47 1280 ×	1024 SXGA VE	SA 60 Hz 63.974 60.013 H-	pos, V-pos
48 SXGA	VESA 75 Hz 79	976 75.025 H-pos, V-pos
49 SXGA	VESA 85 Hz 91	146 85.024 H-pos, V-pos
50 1400 ×	1050 SXGA+ 60	Hz 65.317 59.978 H-neg,	V-pos
55 1280 ×	768 WXGA 60Hz	47.776 59.870 H-neg,	V-pos
56 1280 ×	720 WXGA 60Hz	44.772 59.885 H-neg,	V-pos
60 1360 ×	768 1360 × 768/	60 44.720 59.799 H-neg,	V-pos
61 1440 ×	900 1440 × 900/	60 55.935 59.887 H-neg,	V-pos
63 1280 ×	800 1280 × 800/	60 49.702 59.810 H-neg,	V-pos

Notes

• The receivable digital signals are preset signals of Memory No. 3 to 11, 26, 32, 37, 45, 47, 50, 55 and 56 (VPL-EW7 only).
• When a signal other than the preset signals shown above is input, the picture may not be displayed properly.
• When an SXGA+ signal is input, the image may extend beyond the edges of the screen. In this case, input a signal with no black edges around the image, and disconnect and reconnect the cable or select the input signal by pressing the INPUT key.
• If the resolution of the input signal is different from the panel resolution, the input signal is not displayed in its own resolution, and letters or lines may be uneven.

Installation Diagram

Floor Installation (Front Projection)

This section describes the examples of installing the projector on a desk, etc.

See the chart on page 54 concerning the installation measurements.

The alphabetical letters in the illustration indicate the distances below.

a: distance between the screen and the center of the lens b: distance between the floor and the center of the lens c: distance between the floor and the bottom of the adjusters of the projector X: distance between the floor and the center of the screen (free)

VPL-EX70/EX7

Unit: mm (inches)

PS(inches)		40 60 80	100 120	150 180 200	250 300
(mm) 1016 1524			2032 2540	3048 3810		4572 5080 6350 7620
a	N	1180(46 1/2 )	1780(70 1/8 )	2390(94 1/8 )	2990(117 3/4 )	3600(141 3/4 )	4510(177 5/8 )	5410(213 1/8 )	6020(237 1/8 )	7530(296 1/2 )	9050(356 3/8 )
	M	1330(52 3/8 )	2020(79 5/8 )	2700(106 3/8 )	3380(133 1/8 )	4070(160 3/8 )	5090(200 1/2 )	6110(240 5/8 )	6800(267 3/4 )	8500(334 3/4 )	10210(402 1/8 )
b		Based on the calculation formula given below.
c		Based on the calculation formula given below.

a (N) = {(PS × 29.376) × 1.03} - 31.7 a (M) = {(PS × 35.202) × 0.97} - 31.7 b = x - {PS × 5.055 + (a + 31.7) × 0.1405 - 4.5} c = x - {PS × 5.055 + (a + 31.7) × 0.1405 - 4.5 + 90.5}

VPL-EW7

(When "Aspect" on the Signal menu is set to "Full 2")

Unit: mm (inches)

PS(inches)		40 60 80	100 120 15	50 180 200	250 300
(mm) 1		1016 1524	2032 2540	3048 3810	4572 5080	6350 7620
a	N	1250(49 1/4 )	1890(74 1/2 )	2530(99 5/8 )	3170(124 7/8 )	3810(150 1/8 )	4770(187 7/8 )	5730(225 5/8 )	6370(250 7/8 )	7970(313 7/8 )	9570(376 7/8 )
	M	1410(55 5/8 )	2140(84 3/8 )	2860(112 5/8 )	3580(141)	4300(169 3/8 )	5390(212 1/4 )	6470(254 7/8 )	7200(283 1/2 )	9000(354 3/8 )	10810(425 3/4 )
b		Based on the calculation formula given below.
c		Based on the calculation formula given below.

a (N) = {(PS × 31.076) × 1.03} - 31.7

a (M) = {(PS × 37.252) × 0.97} - 31.7

b = x - {PS × 4.465 + (a + 31.7) × 0.1405 - 4.5}

c = x - {PS × 4.465 + (a + 31.7) × 0.1405 - 4.5 + 90.5}

Notes for VPL-EW7

• The projected image size is the one when “Aspect” on the Signal menu is set to “Full 2”. When “Aspect” on the Signal menu is set to other than “Full 2”, black bands may appear at the top and bottom or right and left of the screen.
• When “Aspect” in the Signal menu is set to “4:3”, the projected image size (diagonal) will be approximately 88% of “Full 2” size.
• When “Aspect” in the Signal menu is set to “16:9”, the projected image size (diagonal) will be approximately 97% of “Full 2” size.

The alphabetical letters in the charts and calculation methods indicate the following.

PS: projected image size measured diagonally

a: distance between the screen and the center of the lens b: distance between the floor and the center of the lens c: distance between the floor and the adjusters of the projector x: free N: minimum M: maximum

Ceiling Installation (Front Projection)

The unit is set so that the bottom is parallel to the ceiling. The V Keystone function has been done.

Distance between the front of the cabinet and the hole for mounting a projector suspension support (front) Unit: mm (inches)

This section describes the examples for installing the projector on the ceiling.

When installing the projector on the ceiling, use a Projector Suspension Support recommended by Sony.

For ceiling installation, ask for qualified Sony personnel.

See the chart on page 56 concerning the installation measurements.

The alphabetical letters in the illustrations indicate the distances below.

a': distance between the hole (front) for mounting a projector suspension support on bottom surface of this projector and the center of the screen

b: distance between the hole (front) for mounting a projector suspension support on bottom surface of this projector and the ceiling

X: distance between the ceiling and the center of the screen

VPL-EX70/EX7

Unit: mm (inches)

PS(inches)		40 60 80	100 120 150	180 200	250 300
(mm) 1016 1524 2032 2540 3048 3810 4572 5080 6350 7620
a’ N	1200(47 1/4 )	1800(70 7/8 )	2410(95)	3010(118 5/8 )	3620(142 5/8 )	4530(178 3/8 )	5440(214 1/4 )	6040(237 7/8 )	7560(297 3/4 )	9070(357 1/4 )
	M 1350(53 1/4 )	2040(80 3/8 )	2720(107 1/8 )	3410(134 3/8 )	4090(161 1/8 )	5120(201 5/8 )	6140(241 7/8 )	6830(269)	8540(336 3/8 )	10250(403 5/8 )
x		Based on the calculation formula given below.
b		Free

a ^ (N) = (PS × 29.415) × 1.03 - 32.0 + 16.4

a ^ (M) = (PS × 35.283) × 0.97 - 32.0 + 16.4

x = b + PS × 5.073 + (a ^ + 32.0 - 16.4) × 0.07344 - 2.3 + 72.5

VPL-EW7

(When "Aspect" on the Signal menu is set to "Full 2")

Unit: mm (inches)

PS(inches)		40 60 80	100 120 150	180 200	250 300
(mm)		1016 1524	2032 2540	3048 3810	4572 5080	6350 7620
a’ N	1270(50)	1910 (75 1/4)	2550 (100 1/2)	3190 (1255/8)	3830 (150 7/8)	4800(189)	5760 (226 7/8)	6400(252)	8000(315)	9610 (378 1/2)
	M 1430 (56 3/8)	2160 (85 1/8)	2880 (113 1/2)	3610 (142 1/4)	4330 (170 1/2)	5420(213)	6510 (256 3/8)	7230 (284 3/4)	9050 (356 3/8)	10860 (4275/8)
x		Based on the calculation formula given below.
b		Free

a ^ (N) = (PS × 31.147) × 1.03 - 32.0 + 16.4

a ^ (M) = (PS × 37.367) × 0.97 - 32.0 + 16.4

x = b + PS × 4.481 + (a ^ + 32.0 - 16.4) × 0.07344 - 2.3 + 72.5

Notes for VPL-EW7

• The projected image size is the one when "Aspect" on the Signal menu is set to "Full 2". When "Aspect" on the Signal menu is set to other than "Full 2", black bands may appear at the top and bottom or right and left of the screen.
• When "Aspect" in the Signal menu is set to "4:3", the projected image size (diagonal) will be approximately 88% of "Full 2" size.
• When "Aspect" in the Signal menu is set to "16:9", the projected image size (diagonal) will be approximately 97% of "Full 2" size.

The alphabetical letters in the charts and calculation methods indicate the following.

PS: projected image size measured diagonally

a': distance between the hole (front) for mounting a projector suspension support on the bottom surface of this projector and the center of the screen

b: distance between the projector suspension support mounting surface on the bottom of this projector and the ceiling

x: distance between the center of the screen and the ceiling

N: minimum

M: maximum

Dimensions

Front

Unit: mm (inches)

Side

Unit: mm (inches)

Top

Unit: mm (inches)

Index

A

Adjust Picture ....30

Air filter 43

Aspect 32, 33

Auto Input Search ....34

B

Background 37

Batteries 17

Brightness 30

C

CC Display 35

Color 30

Color System ....34

Color Temp. 31

Connecting a computer ....18

Connecting a VCR 20

Contrast 30

D

DDE 31

Digital Zoom function ......27

Direct Power On ....37

Direct power On/Off function .....27

Dot Phase ....32

F

fH (Horizontal Frequency) ......39

fV (Vertical Frequency) 39

G

Gamma Mode ....30

H

H Size 32

High Altitude Mode ....37

Hue 30

Image Flip 37

Input-A Signal Sel. 34

Installation 18

notes 6

unsuitable conditions ....7

unsuitable installation 6

L

Lamp Mode 37

Lamp replacement 41

Lamp Timer 39

Lamp Timer Reset 35

Language 36

selecting the menu language 24

Lens 12

Location and function of controls connector panel .... 15

control panel 13

rear/bottom 11

Remote Commander 16

top/right side/front 11

M

Menu

clearing the menu display 29

INFORMATION Menu 39

INPUT SETTING menu 32

INSTALL SETTING menu 37

MENU SETTING menu 36

PICTURE SETTING menu 30

SET SETTING menu 34

using a menu 28

Menu Position 36

Message List caution 47

warning 46

0

Optional accessories 50

P

Panel Key Lock 35

Picture Mode 30

Pin assignment 50

Power turn on 22

Power Saving 35

Presentation 27

Preset Memory No. 33

Projecting 21

R

Remote Commander 16

front remote control detector 11

location and function of controls ..... 16

Reset

resetting an item 29

RS-232C connector ....50

s

Security bar 12

Security Lock 25,37

Security lock 12

Sharpness ....30

Shift 32

Smart APA 34

Specifications 48

Start Up Image 36

Status 36

Supplied accessories ....49

T

Troubleshooting 44

V

V Keystone 37

Volume 31

About Trademarks

• Adobe Acrobat is a trademark of Adobe Systems Incorporated.
• Windows is a registered trademark of Microsoft Corporation in the United States and/or other countries.
• Kensington is a registered trademark of Kensington Technology Group. • Macintosh is a registered trademark of Apple Inc. • VESA is a registered trademark of the Video Electronics Standards Association.
• Display Data Channel is a trademark of the Video Electronics Standards Association.
• All other trademarks and registered trademarks are trademarks or registered trademarks of their respective holders. In this manual, ^TM and marks are not specified.