The Heaven 2.0 - Range hood FABER - Free user manual and instructions

Product Type	Cooker Hood
Brand	Faber
Model	The Heaven 2.0
Dimensions (W x D x H)	90 x 50 x 60 cm (estimated)
Weight	Approximately 15 kg
Electrical Supply	220-240 V, 50/60 Hz
Maximum Power	300 W (estimated)
Maximum Airflow	700 m³/h (estimated)
Maximum Noise Level	65 dB(A) (estimated)
Lighting	Integrated LED bulbs
Number of Speeds	3 speeds + intensive
Main Functions	Extraction, recirculation, lighting, touch control
Maintenance and Cleaning	Dishwasher-safe grease filters, replaceable charcoal filter
Safety	Automatic shut-off, overheating protection
Spare Parts and Repairability	Filters, bulbs, remote control (if applicable), repair possible by professional
Warranty	2 years (parts and labor)

Frequently Asked Questions - The Heaven 2.0 FABER

How to install the The Heaven 2.0 hood?

Installation must be carried out by a qualified professional. Ensure that the hood is securely fixed to the wall and that the exhaust duct is properly connected. Follow the instructions in the provided manual.

What is the recommended mounting height?

The recommended height between the hood and the cooking surface is 65 to 75 cm for optimal extraction.

How to clean the grease filters?

The metal grease filters can be washed in the dishwasher or by hand with mild detergent. Let them dry completely before reinstalling.

How often should the charcoal filter be replaced?

In recirculation mode, the charcoal filter should be replaced every 3 to 6 months depending on usage.

How to change the LED bulbs?

The LED bulbs are integrated and must be replaced by a professional. Contact Faber after-sales service.

The hood is noisy, what to do?

Check that the hood is properly installed and that the filters are clean. Unusual noise may indicate a motor or ventilation issue.

Can I use the hood in recirculation mode without duct?

Yes, the hood can operate in recirculation mode with a charcoal filter. The air is purified and returned to the kitchen.

How to reset the filter saturation indicator?

After cleaning or replacing the filters, press and hold the corresponding control button for 3 seconds to reset the indicator.

Where can I find spare parts?

Spare parts are available from Faber customer service or authorized dealers. Use your model reference.

How to contact Faber technical support?

You can contact Faber technical support by phone or via the contact form on the official website. Have your model number and purchase date ready.

USER MANUAL The Heaven 2.0 FABER

RECOMMENDATIONS AND SUGGESTIONS 13

CHARACTERISTICS 16

INSTALLATION....17

USE 18

MAINTENANCE 20

TABLE OF CONTENTS

EN

RECOMMENDATIONS AND SUGGESTIONS 22

CHARACTERISTICS....25

INSTALLATION....26

USE 27

MAINTENANCE 29

TABLE OF CONTENTS

DE

Control panel Remote control

Lighting

The Instructions for Use apply to several versions of this appliance.

Accordingly, you may find descriptions of individual features that do not apply to your specific appliance.

INSTALLATION

• The manufacturer will not be held liable for any damages resulting from incorrect or improper installation.
• The minimum safety distance between the cooker top and the extractor hood is 650 mm (some models can be installed at a lower height, please refer to the paragraphs on working dimensions and installation).
• Check that the mains voltage corresponds to that indicated on the rating plate fixed to the inside of the hood.
• For Class I appliances, check that the domestic power supply guarantees adequate earthing.

Connect the extractor to the exhaust flue through a pipe of minimum diameter 120 mm. The route of the flue must be as short as possible.

- Do not connect the extractor hood to exhaust ducts carrying combustion fumes (boilers, fireplaces, etc.).

- If the extractor is used in conjunction with non-electrical appliances (e.g. gas burning appliances), a sufficient degree of aeration must be guaranteed in the room in order to prevent the backflow of exhaust gas. The kitchen must have an opening communicating directly

with the open air in order to guarantee the entry of clean air. When the cooker hood is used in conjunction with appliances supplied with energy other than electric, the negative pressure in the room must not exceed 0.04 mbar to prevent fumes being drawn back into the room by the cooker hood.

- The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels (not applicable to appliances that only discharge the air back into the room).

- In the event of damage to the power cable, it must be replaced by the manufacturer or by the technical service department, in order to prevent any risks.

• If the instructions for installation for the gas hob specify a greater distance specified above, this has to be taken into account. Regulations concerning the discharge of air have to be fulfilled.
• Use only screws and small parts in support of the hood. Warning: Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards.
• Connect the hood to the mains through a two-pole switch having a contact gap of at least 3 mm.

USE

• The extractor hood has been designed exclusively for domestic use to eliminate kitchen smells.
• Never use the hood for purposes other than for which it has been designed.
• Never leave high naked flames under the hood when it is in operation.
• Adjust the flame intensity to direct it onto the bottom of the pan only, making sure that it does not engulf the sides.

- Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames.

- Do not flambè under the range hood; risk of fire.

- This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of

experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

- “CAUTION: Accessible parts may become hot when used with cooking appliances.”

MAINTENANCE

• Switch off or unplug the appliance from the mains supply before carrying out any maintenance work.
• Clean and/or replace the filters after the specified time period (fire hazard).
• The grease filters must be cleaned every 2 months of operation, or more frequently for particularly heavy usage, and can be washed in a dishwasher.
• The activated charcoal filter is not washable and cannot be regenerated, and must be replaced approximately every 4 months of operation, or more frequently for particularly heavy usage.
• Failure to carry out cleaning as indicated will result in a fire hazard.
• Clean the hood using a damp cloth and a neutral liquid detergent.

The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

Dimensions

Fixing the Hood

In all cases where the ceiling is not strong enough at the suspension point, the installer must provide strengthening using suitable plates and backing pieces anchored to the structurally sound parts.

ELECTRICAL CONNECTION

Connect the hood to the mains through a two-pole switch having a contact gap of at least 3 mm.

Control panel

Button	Led	Function
L	- Turns the	lights ON/OFF at maximum strength.
		Press and hold the button for approximately 5 seconds, with all the loads turned off (Motor and Lights), to turn the Activated Charcoal Filter alarm on. The 4 LEDs on the buttons flash twice to confirmTo turn the alarm off, press the button again and hold for at least 5 seconds. The 4 LEDs on the buttons flash once.
T1	Fixed Turns the motor on/off at speed one.
	Flashing	24h functionPress and hold the button for approx. 2 seconds to Activate/Deactivate the motor in 24h Air Circulation mode, a speed that allows ducting for 10 minutes every hour, for a 24 hour cycleCannot be activated if Intensive or Delay modes are active.
T2	Fixed Turns the Motor on at speed two.
	Flashing	Delay function:Press and hold the button for approx. 3 seconds to Activate/Deactivate the Delay function (automatic switching off of the Motor, the Fans and the Lighting with a 30' delay).Cannot be enabled when Intensive or 24h are on.
T3	Fixed Turns the Motor on at speed three.
		Press and hold the button for approximately 3 seconds, with all the loads turned off (Motor and Lights), to reset the Filter saturation alarm. The LED S1 flashes three times.
T4	Fixed Turns the Motor on at Intensive Speed.This speed is timed to run for 6 minutes. At the end of this time, the system returns automatically to the speed that was set before. If it is activated with the motor turned off, the hood will switch to OFF at the end of the time.
		Press and hold for 5 seconds to enable the remote control, indicated by the LED flashing twice.Press and hold for 5 seconds to disable the remote control, indicated by the LED flashing just once.
S1	Fixed Signals the Metal Grease Filter saturation alarm, indicating that it is necessary to wash the filters. The alarm is triggered after the Hood has been in operation for 100 working hours.
	Flashing	When this is activated, it signals the Activated Charcoal Filter saturation alarm, indicating that the filter must be changed; the Metal Grease Filters must also be washed. The Activated Charcoal Filter saturation alarm comes into operation after the Hood has been working for 200 hours.

REMOTE CONTROL

The appliance can be controlled using a remote control powered by 1.5 V carbon-zinc alkaline batteries of the standard LR03-AAA type (not included).

• Do not place the remote control near heat sources.
• Used batteries must be disposed of in the proper manner.

Remote control panel

➊	Motor Brief pressure: Motor On / Off
-		Decreases the working speed each time it is pressed.
+		Increases the working speed each time it is pressed.
➊	Intensive Activates/Deactivates Intensive operation.
➊	Delay / 24H	Brief pressure: Activates/Deactivates the Delay function: automatic switch-off with a 30' delay. The display shows the operating speed and the dot at the bottom right flashes once a second.Press for 2 seconds: Activates/Deactivates the 24h function: turns the suction motor on at speed one and effects one 10 minute extraction every hour. The display shows the number 24 and the dot at the bottom right flashes once a second.
➊	Light Brief pressure: Lights On / Off

Opening Panel

• Open the Panel by pulling it.
• Clean the outside with a damp cloth and neutral detergent.
• Clean the inside using a damp cloth and neutral detergent; do not use wet cloths or sponges, or jets of water; do not use abrasive substances.

Metal grease filters

These can be washed in the dishwasher, and need to be cleaned whenever the S1 LED comes on or at least once every 2 months of use, or more frequently if use is particularly intensive.

CLEANING THE FILTERS

Resetting the alarm signal

• Turn the Lights and the Suction Motor off.
• Press T3 and hold for at least 3 seconds, until LED flashes three times in confirmation.

Cleaning the Filters

• Open the doors.
• Remove the Filter, pushing it towards the back of the unit and at the same time pulling downward.
• Wash the filter without bending it, and leave it to dry thoroughly before replacing (if the surface of the filter changes colour over time, this will have absolutely no effect on its efficiency).
• Replace, taking care to ensure that the handle faces forwards.
• Close the doors again.

This cannot be washed or regenerated, and must be changed when LED S1 starts to flash, or at least once every 4 months. The alarm signal, if it has been activated, only appears when the suction motor is turned on.

Activating the alarm signal

• In recirculation version hoods, the filter saturation alarm must be activated on installation or at a later date.
• Turn the lights and the suction motor off.
• Press button T2 and hold it for 5 seconds until the LED flashes twice in confirmation:

CHANGING

Resetting the alarm signal

• Turn the lights and the suction motor off.
• Press T3 and hold for at least 3 seconds, until LED flashes three times in confirmation.

Changing the filter

• Open the doors.
• Remove the metal grease filter.
• Fit the new Filters, as indicated (B).
• Replace the Metal grease filters.
• Close the doors.

- Remove the saturated Activated Charcoal Filters, as indicated (A).

Lighting unit

- For replacement contact technical support ("To purchase contact technical support").

Lighting

Metal grease filters

Lighting

LED spotlight

Metal grease filters

Lighting

Lighting

Control panel – Remote control

Metal grease filters

Cleaning the filters

Lighting

Lighting

Control panel – Remote control

Metal grease filter

Cleaning the filters

Lighting

Control panel – Remote control

➊	Motor Raskt	trykk: Motoren slås på eller av.
-		Reduserer driftshastigheten hver gang det trykkes på knappen.
+		∅ker driftshastigheten hver gang det trykkes på knappen.
➊	Intensiv	Aktiverer/deaktiverer den intensive hastigheten.
➊	24H/Delay	Raskt trykk: Aktiverer/deaktiverer Delay-funksjonen: den automatiske slukkingen med en forsinkelse på 30 minutter. På displayet vises driftshastigheten. Punktet nede til høyre på displayet blinker en gang i sekundet.Trykk på knappen i 2 sekunder for å aktivere/deaktivere 24h-funksjonen: Slår motoren på ved den første hastigheten og tillater en utsuging i 10 minutter pr. time. På displayet vises tallet 24. Punktet nede til høyre på displayet blinker en gang i sekundet.
➊	Belysning	Raskt trykk: Belysningen slås på eller av.

Opening the panel

Lighting

- Contact customer service for replacement ("Contact customer service for purchase").

Remote control panel

Cleaning the filters

Lighting

Remote control panel

Lighting