LED KKL-30 - Lamp Eurolite - Free user manual and instructions
Find the device manual for free LED KKL-30 Eurolite in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | LED Effect Lamp |
| Model | LED KKL-30 |
| Light Source | 30W RGB LED |
| Beam Angle | 25° |
| DMX Channels | 3/7/12 selectable |
| Control Modes | DMX, Master/Slave, Auto, Sound-Active |
| Input Voltage | 100-240V AC, 50/60Hz |
| Power Consumption | 30W |
| Dimensions (L x W x H) | 200 x 180 x 110 mm |
| Weight | 1.2 kg |
| Housing Material | Aluminum alloy |
| Cooling System | Convection, no fan |
| Mounting Options | Floor standing or hanging bracket |
| Operating Temperature | 0°C to 40°C |
| Protection Rating | IP20 (indoor use only) |
| Included Accessories | Power cord, user manual |
| Spare Parts Available | LED module, power supply |
| Maintenance | Wipe with dry cloth; no solvents |
| Safety Precautions | Do not expose to moisture or rain |
Frequently Asked Questions - LED KKL-30 Eurolite
How do I connect the LED KKL-30 to a DMX controller?
Use a 3-pin XLR cable to connect the DMX IN of the fixture to the controller's output. Set the DMX address using the Menu and Up/Down buttons. Refer to the manual for channel mapping.
What is the maximum number of fixtures I can daisy-chain?
You can chain up to 32 fixtures on a single DMX line. Use DMX OUT to connect to the next fixture's DMX IN.
Can I use this lamp outdoors?
No, the LED KKL-30 is rated IP20 and should only be used indoors in dry conditions. Exposure to moisture may cause damage.
How do I replace the LED module?
Disconnect power, remove the back cover screws, detach the old module, and connect the new one. Ensure correct polarity. Only use Eurolite approved spare parts.
The lamp does not respond to DMX. What should I check?
Verify the DMX cable is properly connected, the controller is sending signal, and the fixture's DMX address matches the controller's channel. Also check that the mode is set to DMX.
How can I clean the fixture?
Turn off and unplug the lamp. Use a soft dry cloth to wipe the housing and lens. Do not use any liquids or cleaners.
What does the 'Sound-Active' mode do?
In Sound-Active mode, the lamp responds to ambient music via a built-in microphone. It changes colors and patterns in sync with the beat. Use the Menu to select sensitivity.
Can I mount the fixture upside down?
Yes, the fixture can be mounted on a stand or hung from a truss using the included bracket. Ensure it is securely fastened and never point directly into eyes.
The lamp overheats and shuts off. What can I do?
Ensure the ventilation slots are not blocked. Keep at least 20 cm clearance around the fixture. Do not operate in ambient temperatures above 40°C.
How do I reset the lamp to factory settings?
Press and hold the Menu button for 5 seconds until the display shows 'rES'. Then press Enter to confirm. The lamp will reboot with default settings.
User questions about LED KKL-30 Eurolite
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Lamp in PDF format for free! Find your manual LED KKL-30 - Eurolite and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. LED KKL-30 by Eurolite.
USER MANUAL LED KKL-30 Eurolite
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Eurolite
Model : LED KKL-30
Category : Lamp