HATS6DCS56B - Range hood HAIER - Free user manual and instructions

Product Type	Cooker Hood
Brand	Haier
Model	HATS6DCS56B
Width	60 cm
Depth	50 cm
Height	30 cm (min) - 40 cm (max)
Weight	12 kg
Power Supply	220-240 V, 50 Hz
Motor Power	150 W
Lighting Power	2 x 1.5 W LED
Maximum Airflow	650 m³/h
Noise Level (Max Speed)	65 dB(A)
Number of Speeds	3
Controls	Electronic Touch Buttons
Extraction Mode	Ducted / Recirculating
Grease Filter	Aluminum, washable
Charcoal Filter	Optional, replaceable
Energy Class	A
Annual Energy Consumption	45 kWh
Duct Diameter	150 mm
Installation Type	Under cabinet / Wall mount
Maintenance	Clean grease filter monthly; replace charcoal filter every 3-6 months
Safety Features	Auto shut-off timer, motor overheating protection
Spare Parts	Grease filters, charcoal filters, LED bulbs available from Haier service centers

Frequently Asked Questions - HATS6DCS56B HAIER

How do I install the Haier HATS6DCS56B cooker hood?

Installation should be done by a qualified professional. The hood must be mounted at least 65 cm above electric hobs and 75 cm above gas hobs. Ensure proper ducting for extraction mode or install charcoal filters for recirculation.

How often should I clean the grease filter?

The aluminum grease filter should be cleaned every month for normal usage. You can wash it in a dishwasher or by hand with warm soapy water. Ensure it is completely dry before reinstalling.

Can I use the hood without ducting?

Yes, you can use the hood in recirculation mode. You will need to install charcoal filters (purchased separately) to absorb odors. The filters should be replaced every 3-6 months.

What type of light bulbs does the hood use?

The hood uses LED bulbs (1.5 W each). They are integrated and should be replaced by a technician if faulty. Do not attempt to replace them yourself.

How loud is the Haier HATS6DCS56B?

The noise level reaches up to 65 dB(A) at maximum speed. At lower speeds, it is quieter, making it suitable for open-plan kitchens.

What is the warranty period for this hood?

Haier offers a standard 2-year warranty for manufacturing defects. Register your product on the Haier website to activate warranty. Extended warranty may be available.

How do I access the user manual?

The user manual is available for free download on notice-facile.com or the Haier official website. You can also request a printed copy from customer service.

What should I do if the hood stops working?

First, check the power supply and circuit breaker. If it still doesn't work, try resetting the hood by turning it off for a few minutes. If the issue persists, contact Haier customer service for technical support.

Can I wash the charcoal filter?

No, charcoal filters cannot be washed. They must be replaced every 3-6 months depending on usage. Washing them will damage the carbon and reduce effectiveness.

Is the hood suitable for a gas stove?

Yes, but ensure the distance between the hood and the gas hobs is at least 75 cm. Follow the installation guidelines to prevent fire hazards and ensure proper ventilation.

USER MANUAL HATS6DCS56B HAIER

INSTALLATION AND USER'S MANUAL

CONTENT

INTRODUCTION 02

SAFETY PRECAUTION 02

ELECTRICAL INSTALLATION 04

SPECIFICATION 05

INSTALLATION (VENT OUTSIDE) 06

INSTALLATION (VENT INSIDE) 13

DESCRIPTION OF COMPONENTS 14

OPERATION 14

MAINTENANCE 15

TROUBLESHOOTING 16

CONFORMITY WITH DIRECTIVES 16

ENVIRONMENTAL PROTECTION 17

INTRODUCTION

Thank you for choosing this cooker hood.

This instruction manual is designed to provide you with all required instructions related to the installation, use and maintenance of the appliance. In order to operate the unit correctly and safely, please read this instruction manual carefully before installation and usage.

The cooker hood uses high quality materials, and is made with a streamlined design. Equipped with large power electric motor and centrifugal fan, it also provides strong suction power, low noise operation, non-stick grease filter and easy assembly installation.

SAFETY PRECAUTION

☐ Never let the children operate the machine. ☐ The cooker hood is for home use only, not suitable for barbecue, roast shop and other commercial purpose. ☐ The cooker hood and its filter should be clean regularly in order to keep in good working condition. ☐ Clean the cooker hood according to the instruction manual and keep the unit from danger of burning. ☐ Forbid the direct baking from the gas cooker. ☐ Please keep the kitchen room a good convection. Before connecting this appliance check that the power supply cord is not damaged. A damage supply cord must be replaced by qualified service personnel only. There shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels; ☐ The air must not be discharged in fumes from appliances burning gas or other fuels; ☐ Regulations concerning the discharge of air have to be fulfilled. Children should be supervised to ensure that they do not play with the appliance. ☐ Do not flambé under the range hood. ☐ The range hood is not intended to be installed over a hob having more than four hob elements

• These shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels (not applicable to appliances that only discharge the air back into the room);
• the details concerning the method and frequency of cleaning.
• there is a fire risk if cleaning is not carried out in accordance with the instructions:
• do not flame under the range hood;
• CAUTION: Accessible parts may become hot when used with cooking appliances.

Electrical Shock Hazard

~ Only plug this unit into a properly earthed outlet. If in doubt seek advice from a suitably qualified engineer. ~ Failure to follow these instructions can result in death, fire, or electrical shock.

Electrical Installation

All installation must be carried out by a competent person or qualified electrician. Before connecting the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate.

Direct Connection

The appliance must be connected directly to the mains using an omnipolar circuit breaker with a minimum opening of 3mm between the contacts.

The installer must ensure that the correct electrical connection has been made and that it complies with the wiring diagram.

The cable must not be bent or compressed.

Regularly check the power plug and power cord for damage. If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.

WARNING: This is a Class I appliance and MUST be earthed.

This appliance is supplied with a 3 core mains cable coloured as follows:

Brown = L or Live

Blue = N or Neutral

Green and Yellow = E or Earth

The fuse must be rated at 3 Amps.

Standard Installation Accessories List

Spec. Qty	Illustration Picture
Casing 1
Upper Chimney 1
Lower Chimney 1
Lower chimney bracket 1
Upper chimney bracket 1
Hanging Board 1
φ8 rawl plugs φ8×φ6 white color		9
Screws ST4.0×30		9
φ7.2screws ST4.0×8		2
Air outlet 1
Carbon filter		2

If you have an outlet to the outside, your cooker hood can be connected as below picture by means of an extraction duct (enamel, aluminum, flexible pipe non flammable with an interior diameter of 150mm).

1. Before installation, turn the unit off and unplug it from the outlet.

1. The cooker hood should be placed at a distance of 65~75cm above the cooking plane for best effect.

1. Drill 3 x 8mm holes to accommodate the bracket. Screw and tighten the bracket onto the wall with the screws provided.

1. Lift the cooker hood and hang it onto the wall bracket hook.

1. Attach the one-way valve to the air outlet of the cooker hood. Then, connect the exhaust pipe onto the one-way valve as shown below.

Exhaust pipe

Cooker hood

6.

i. Place the glass in the appropriate position on top of the cooker hood.

ii. Fix it with 4 screws and washers. To avoid cracking the glass, do not tighten the screws too strongly.

i. Insert the inner chimney into the outer chimney. Then pull the inner chimney upwards. Adjust to reach the required height.

ii. Slide the chimney to adjust its height. When the required height is reached, hang the fixing hole onto the fixing screws as shown in the pictures below.

8.

i. Drill 2 x 8mm holes to accommodate plate II. Screw and tighten plate II onto the wall with the 2 screws provided. ii. Assemble the chimney onto the unit and fix it with 2 screws.

Standard Installation Accessories List

Spec. Illustration Picture Qty
Air Deflector		1
Bracket		1
φ8 rawl plugs φ8×φ6 white color		2
Screws ST4.0×30		2
Screws ST3.5×12		2

INSTALLATION (AIR DEFLECTOR):

The air deflector is mentioned as included and not optional.

1. Before installation, curve both ends of the bracket as shown below:

1. Fix the bracket to the T-shaped plastic outlet with 2 pcs ST3.5x12mm screws provided.

1. Drill 2 holes to accommodate the wall plugs, then screw and tighten the bracket onto the wall with 2 pcs ST4x30mm screws provided.

1. Attach the exhaust pipe onto the air outlet of the cooker hood as shown below:

1. Install the chimney to the unit and fix it.

Please kindly be noted: T-shaped plastic outlet and v-flaps cannot be used at the same time. You can use them in two ways: 1) Add v-flap on existing outlet; 2) Use T-shaped plastic outlet, no add v-flap.

Note: The product is provided with v-flap accessory. This accessory is not mandatory for installation, operation and use of the product.

INSTALLATION (VENT INSIDE)

If you do not have an outlet to the outside, exhaust pipe is not required and the installation is similar to the one shown in section "INSTALLATION (VENT OUTSIDE)".

Activated carbon filter can be used to trap odors.

In order to install the activated carbon filter, the grease filter should be detached first. Press the lock and pull it downward.

Plug the activated carbon filter into the unit and turn it in clockwise direction. Repeat the same on the other side.

NOTE:

Make sure the filter is securely locked. Otherwise, it would loosen and cause danger. When activated carbon filter is attached, the suction power will be lowered.

OPERATION

STANDBY MODE.

After plugging in, all lighting and the system are in STANDBY MODE.

1 Low Speed button

It is used for ventilation in the kitchen. It is suitable for simmering and cooking that do not produce much steam.

2 Medium Speed button

The airflow speed is ideal for ventilation during standard cooking operations.

3 High Speed button

When high density of smoke or steam is produced, press the high-speed button for effective ventilation.

B Booster function

This hood has a booster function. To activate the booster, press

B to speed 4, entering the highest speed while the hood is in use. It will increase speed for 5 minutes before slowing down again.

Light

Short press to turn the lighting on and off.

Quick timer: Long press the light button and hold for 3 seconds. The fan speed buttons will flash and enter a 5-minute countdown. After 5 minutes, the motor and light will turn off automatically with three buzzer sounds.

MAINTENANCE

Before cleaning switch the unit off and pull out the plug.

I. Regular Cleaning

Use a soft cloth moistened with hand-warm mildly soapy water or household cleaning detergent. Never use metal pads, chemical, abrasive material or stiff brush to clean the unit.

II. Monthly Cleaning for Grease Filter

ESSENTIAL: Clean the filter every month can prevent any risk of fire.

The filter collects grease, smoke and dust..... so the filter is directly affecting the efficiency of the cooker hood. If not cleaned, the grease residue (potential flammable) will saturate on the filter. Clean it with household cleaning detergent.

III. Annual Cleaning for Activated Carbon Filter

Apply SOLELY to unit that installed as a recirculation unit (not vented to the outside). This filter traps odors and must be replaced at least once a year

depending on how frequent the cooker hood used.

IV. Changing a light bulb

Remove the screws on the glass, take off the hood glass. Find the bulb that requires replacement, you will find it located in the light fixture which is inside the exposed section of the canopy.

Disconnect the light wiring point and remove the bulb holders and wiring from the hood. Important: It's not possible to replace the bulbs individually, it will be necessary to obtain the bulbs, bulb holders and wiring as a complete part. (LED light: MAX 1.5W)

Fit the replacement bulbs, bulb holders and wiring in the same manners as the originals. Then reconnect the light wiring point.

Refit the hood glass and fasten the glass screws. Make sure the screws are fully tightened.

TROUBLESHOOTING

Fault	Cause	Solution
Light on, but fan does not work	The fan blade is jammed.	Switch off the unit and repair by qualified service personnel only.
	The motor is damaged.
Both light and fan do not work	Halogen light bulb burn.	Replace the bulb with correct rating.
	Power cord looses.	Plug in to the power supply again.
Serious Vibration of the unit	The fan blade is damaged.	Switch of the unit and repair by qualified service personnel only.
	The fan motor is not fixed tightly.	Switch off the unit and repair by qualified service personnel only.
	The unit is not hung properly on the bracket.	Take down the unit and check whether the bracket is in proper location.
Suction performance not good	Too long distance between the unit and the cooking plane	Readjust the distance to 65-75cm

CUSTOMER ASSISTANCE SERVICE

If you cannot identify the cause of the operating anomaly, switch off the appliance and contact the Assistance Service.

PRODUCT SERIAL NUMBER. Where can I find it?

It is important you to inform the Assistance Service of your product code and its serial number (a 16 character code which begins with the number 3); this can be found on the guarantee certificate or on the data plate located on the appliance.

It will help to avoid wasted journeys to technicians, thereby (and most significantly) saving the corresponding callout charges.

This appliance is marked according to the European directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE).

WEEE contains both polluting substances (which can cause negative consequences for the environment) and basic components (which can be re-used). It is important to have WEEE subjected to specific

treatments, in order to remove and dispose properly all pollutants, and recover and recycle all materials.

Individuals can play an important role in ensuring that WEEE does not become an environmental issue; it is essential to follow some basic rules:

WEEE should not be treated as household waste;

WEEE should be handed over to the relevant collection points managed by the municipality or by registered companies. In many countries, for large WEEE, home collection could be present.

In many countries, when you buy a new appliance, the old one may be returned to the retailer who has to collect it free of charge on a one-to-one basis, as long as the equipment is of equivalent type and has the same functions as the supplied equipment.

INSTRUKCJA OBSŁUGI I INSTALACJI

SPIS TREŚCI

WPROWADZENIE 19

SAFETY PRECAUTIONS AND 19

6.

CLOSING DIRECTION

NOTE:

1. Fix the non-return valve to the air outlet of the extractor. Then attach the exhaust hose to the non-return valve, as shown below.

NOTE:

INSTALLATION (Wall mounting)

Range hood

6.

NOTE:

Absorber

6.

Close

NOTE:

Hood

6.

NOTE:

1. Before installation, turn off the unit and unplug it from the outlet.

1. The range hood should be installed at a distance of 65~75cm above the cooking surface for best results.

1. Drill holes 3 x 8 mm for mounting the brackets. Attach the bracket to the wall with screws.

1. Leave the range hood and hang it on the wall hook of the bracket.

Range hood

6.

i. Place the glass in the appropriate position on top of the range hood.

ii. Secure with 4 screws and washers. To avoid cracking the glass, do not overtighten the screws.

ii. Slide the chimney to adjust its height. When it reaches the desired height, insert the fixing screws into the fixing holes as shown in the figures below.

8.

i. Drill holes 2 x 8 mm for mounting plate II. Screw and tighten plate II to the wall with the 2 supplied screws. ii. Mount the chimney onto the unit and secure it with 2 screws.

List of standard installation equipment

Spec.	Slika ilustracije	Kol.
Zračni deflektor		1
nosač		1
ø8 zidni čepoviø8 × ø6 bijela boja		2
VijciST4.0x30		2
VijciST3.5x12		2

INSTALLATION (AIR DEFLECTOR):

1. Drill 2 holes to insert wall plugs, then screw and tighten the bracket to the wall using the supplied screws (2 pcs ST4x30mm).

1. Install the chimney on the unit and secure it.

Note: The plastic T-shaped outlet and the v-flap cannot be used at the same time. You can use them in two ways: 1) Add the v-flap to the existing outlet; 2) Use the plastic T-shaped outlet without adding the v-flap.

Note: The product is equipped with accessories for the v-flap. This accessory is not mandatory for installation, operation, and use of the product.

INSTALLATION (INDOOR VENT)

The activated carbon filter can be used to prevent the spread of unpleasant odors.

To install the activated carbon filter, you must first remove the grease filter. Press the latch and pull it downwards.

Connect the activated carbon filter to the unit and turn it clockwise. Repeat the same on the other side.

CLOSE

NOTE: