Orbit 3 - Synthesizer Joranalogue - Free user manual and instructions
Find the device manual for free Orbit 3 Joranalogue in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Eurorack Synthesizer Module |
| Brand | Joranalogue |
| Model | Orbit 3 |
| Module Width | 8 HP (40.3 mm) |
| Module Depth | 29 mm (including power connector) |
| Weight | Approx. 100 g |
| Power Consumption | +12V: 60 mA, -12V: 60 mA |
| Oscillators | Three analog voltage-controlled oscillators |
| Waveforms | Sine, triangle, sawtooth, square (with PWM) |
| Modulation | Exponential and linear FM, sync, and waveform morphing |
| Output Level | 10 Vpp typical |
| Input Impedance | 100 kΩ typical |
| Frequency Range | 0.1 Hz to 10 kHz (max frequency depends on control voltage) |
| Cleaning | Use a dry, lint-free cloth. Do not use liquids or solvents. Disconnect power before cleaning. |
| Safety | This module is designed for use in a Eurorack case. Do not expose to moisture, extreme temperatures, or shock. Refer to the user manual for full safety instructions. |
| Spare Parts & Repairability | Contact Joranalogue or authorized distributors for spare parts. The module is not user-serviceable; repairs should be carried out by qualified technicians. |
| General Information | The Orbit 3 is a multifunctional analog oscillator/scanner module featuring three synchronized VCOs with extensive modulation capabilities. |
Frequently Asked Questions - Orbit 3 Joranalogue
What is the Joranalogue Orbit 3?
The Orbit 3 is an analog Eurorack synthesizer module featuring three voltage-controlled oscillators with waveform morphing and synchronization capabilities.
What are the power requirements for the Orbit 3?
The module requires +12V (60 mA) and -12V (60 mA) from the Eurorack power supply. It is reverse polarity protected.
Can the Orbit 3 be used as an LFO?
Yes, by setting the frequency controls to low ranges, the oscillators can function as LFOs down to 0.1 Hz.
How do I calibrate the Orbit 3?
Calibration is performed using the trimmer potentiometers on the rear PCB. Detailed steps are provided in the user manual. It is recommended to calibrate after initial setup or if pitch tracking is off.
What is the width of the Orbit 3?
The module occupies 8 HP (40.3 mm) in a standard Eurorack case.
Does the Orbit 3 support FM?
Yes, it supports both exponential and linear frequency modulation inputs for each oscillator.
How do I clean the module?
Use a dry, soft cloth to wipe the front panel and controls. Avoid liquids and never spray anything directly onto the module. Always disconnect power before cleaning.
What output level can I expect from the Orbit 3?
The typical output level is 10 Vpp, which is suitable for driving other Eurorack modules without additional amplification.
Is the Orbit 3 compatible with my Eurorack case?
It is compatible with any Eurorack case that provides standard +12V/-12V power rails and sufficient current. Ensure proper mounting depth (29 mm).
Where can I download the user manual?
The user manual is available for free download on the product page at notice-facile.com or the manufacturer's website.
User questions about Orbit 3 Joranalogue
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Synthesizer in PDF format for free! Find your manual Orbit 3 - Joranalogue and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Orbit 3 by Joranalogue.
USER MANUAL Orbit 3 Joranalogue
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Joranalogue
Model : Orbit 3
Category : Synthesizer