PKGA 14.4 A1 - Multitools PARKSIDE - Free user manual and instructions

Product Type	Multi-tool (oscillating)
Model	PKGA 14.4 A1
Brand	Parkside
Power Supply	14.4 V Li-ion battery (not included)
Oscillation Angle	3.2° (left/right)
No-Load Speed	5,000 - 10,000 rpm (variable)
Weight	1.2 kg (with battery)
Dimensions (L x W x H)	280 x 70 x 70 mm
Battery Voltage	14.4 V
Accessories Included	3 sanding pads, 1 scraper blade, 1 saw blade, 1 segment blade
Tool-less Blade Change	Yes
Variable Speed Trigger	Yes
LED Work Light	Yes
Soft Grip Handle	Yes, rubberized
Battery Protection System	Overload, overheat, deep discharge protection
Maintenance	Clean with dry cloth; keep vents free of dust
Safety Features	Lock-off switch, anti-slip surface, battery removal before storage
Spare Parts Availability	Battery, charger, and accessories via Parkside service
Reparability Index	High (battery and accessories replaceable)
User Manual Language	English (EN) available in PDF

Frequently Asked Questions - PKGA 14.4 A1 PARKSIDE

What batteries are compatible with the Parkside PKGA 14.4 A1?

The tool uses 14.4 V Li-ion batteries from the Parkside system (e.g., PABS 14.4 series). Always use original batteries to ensure fit and safety.

Can I use the multi-tool while charging?

No, the tool is cordless and runs on battery power. Do not attempt to use it while the battery is connected to the charger.

How do I change accessories on the PKGA 14.4 A1?

The tool features tool-less blade change. Simply press the release lever, insert the accessory, and release. Ensure it locks securely before use.

What is the oscillation angle and speed range?

The oscillation angle is 3.2° (1.6° each side). Speed is variable from 5,000 to 10,000 rpm, controlled by the trigger.

What materials can I cut with the included blades?

The saw blade cuts wood, drywall, and plastics. The segment blade cuts metal, screws, and nails. Use appropriate accessories for other materials.

How do I maintain the multi-tool?

Clean the housing with a dry cloth. Keep ventilation slots free of dust. Do not use solvents. Check screws and accessories for wear regularly.

Is the battery protected against overcharging?

Yes, the Parkside battery and charger have overload, overheat, and deep discharge protection. The charger automatically stops when full.

Can I buy spare parts for the PKGA 14.4 A1?

Yes, spare parts like batteries, chargers, and accessories are available through Parkside service centers or online. Check the manual for part numbers.

What should I do if the tool vibrates excessively?

Stop immediately. Check if the accessory is fully locked and not damaged. If vibration persists, it may indicate wear; contact customer service.

How do I store the multi-tool safely?

Remove the battery before storage. Store in a dry, cool place away from children. Keep accessories in a case to prevent damage.

USER MANUAL PKGA 14.4 A1 PARKSIDE

4-IN-1 CORDLESS COMBINATION TOOL PKGA 14.4 A1

GB

4-IN-1 CORDLESS COMBINATION TOOL

Translation of the original instructions

RO

MAŞINĂ COMBI CU ACUMULATOR

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the device.

HR

Prije nego što pročitate tekst, otvorite stranicu sa slikama i upoznajte se na osnovu toga sa svim funkcijama uređaja.

RO

GB Translation of the original instructions Page 4

General Description......5

Scope of delivery....5

Overview....5

Technical Data......6

Notes on Safety 7

Symbols......7

General safety instructions for power tools....8

Correct handling of the battery charger..10

Additional safety instructions .....11

Charging the battery......13

Remove/insert rechargeable battery....13

Recharging the battery 13

Used batteries 14

Checking the charge status of the rechargeable battery....14

Operation 14

Replacing the appliance attachment ....14

Switching on/off....15

Motor unit with drill attachment PKGA1..15

Motor unit with multi-sander attachment PKGA2....16

Motor unit with sabre saw attachment PKGA3....16

Motor unit with multifunction tool PKGA4....17

Practical tips 18

Sawing....18

Sanding....18

Scraping....18

Cleaning/Maintenance 18

Cleaning....19

Maintenance....19

Storage....19

Waste Disposal/

Environmental Protection ...... 19

Guarantee 20

Repair Service......21

Service-Center 21

Importer 21

Spare Parts/Accessories 22

Trouble Shooting 23

Translation of the original EC declaration of conformity...... 110

Exploded Diagrams......113

Introduction

Congratulations on the purchase of your new device. With it, you have chosen a high quality product. During production, this equipment has been checked for quality and subjected to a final inspection. The functionality of your equipment is therefore guaranteed.

The operating instructions constitute part of this product. They contain important information on safety, use and disposal.

Before using the product, familiarise yourself with all of the operating and safety instructions. Use the product only as described and for the applications specified. Keep this manual safely and in the event that the product is passed on, hand over all documents to the third party.

Intended Use

The appliance is intended for screwing screws in and out and for drilling holes in wood, metal or plastic.

The add-on tools are intended for grinding, sawing and scraping.

The device is not suitable for commercial use.

Any other use that is not explicitly approved in these instructions may result in damage to the equipment and represent a serious danger to the user.

The equipment is designed for use by adults. Adolescents over the age of 16 may use the device only under supervision. The manufacturer is not liable for damages caused by unspecified use or incorrect operation.

General Description

The illustration of the principal functioning parts can be found on the front and back foldout pages.

Scope of delivery

Carefully unpack the trimmer and check that it is complete. Dispose of the packaging material correctly.

• Motor unit with rechargeable battery and drill attachment
• Sabre saw attachment
• Multi-sander attachment
• Multifunction tool
• Accessories for drill attachment
• 6 drill bits (1,5/2/3/4/5/6)
• 6 screwdriver bits, 50 mm
• Bit holder
• Accessories for sabre saw attachment
• Wood sawblade
• Metal sawblade
• Accessories for multi-sander attachment - 5 sanding sheets (2 x 60, 2 x 120, 1 x 240)
  • Accessories for multifunction tool
• Plunge sawblade
• Scraper blade
• Delta sanding plate with 3 sanding sheets (1 × 60, 1 × 80, 1 × 120)
• Charger
• Storage case
• Instruction Manual

Overview

1 Keyless chuck

2 Torque adjustment ring
3 Gear selection switch
4 Drill attachment PKGA1
5 Unlocking lever for appliance attachment
6 Motor unit
7 Direction switch
8 Handle
9 Rechargeable battery
10 Unlock button - rechargeable battery
11 On/off switch
12 Bit holder
13 Screwdriver bits, 50 mm, 6 no.
14 Drill bits 6 no.
15 Charger
16 Storage case
17 Sabre saw attachment PKGA3 18 Footplate
19 Lever for unlocking sawblade
20 Metal sawblade
21 Wood sawblade
22 Sanding plate
23 Multi-sander attachment PKGA2
24 5 sanding sheets
25 Dust extraction adaptor
26 Multifunction tool PKGA4
27 Lever for unlocking tool 28 Arbor
29 Tool holder
30 Delta sanding plate
31 3 sanding sheets
32 Scraper blade
33 Plunge sawblade

Technical Data

4in1 Cordless combination tool ... PKGA 14.4 A1

Motor voltage....14,4 V==

Idling speed ( n₀ )......21000 min ^-1

Sound pressure level ( L_PA ) ..... 86,7 dB(A), K=3 dB

Sound power level ( L_wA ) ..... 97,7 dB(A)

K=3 dB

Motor unit with drill attachment....PKGA1

Idling speed ( n₀ ) ..... 0-400/0-1350 min ¹

Torque max. 25 Nm

Spread drill chuck....1.0-10 mm

Drill diameter

for wood.....max. 25 mm

for steel .... max. 8 mm

Weight (without charger) .....1,5 kg

Vibration ( a_h )

drilling in metal....1,615 m/s ² , K= 1,5 m/s ²

drilling in wood ...1,475 m/s ² , K= 1,5 m/s ²

Motor unit with multisander attachment..PKGA2

Oscillation rate ( n₀ ) .....0-9000 min ^-1

Sanding sheet size ⚡…138 x 97 mm

Weight (without charger)....1,3 kg

Vibration ( a_h ) .....4,383 m/s ² , K=1,5 m/s ²

Motor unit with sabre saw attachment....PKGA3

Stroke rate ( n₀ ) 0-3200 min ^-1

Stroke length 22 mm

Weight (without charger)....1,7 kg

Vibration ( a_h )

Sawing boards....11,926 m/s ²

Sawing wood beams ..... 12,392 m/s ²

K = 1,5 m / s²

Motor unit with multifunction tool......PKGA4

Oscillation rate ( n₀ ) .....0-20000 min ^-1

Oscillation angle....3,0°

Weight (without charger)....1,3 kg

Battery (Li-Ion)....PAP14.4

Nominal voltage....14,4 V==

Capacity....1,5 Ah

Charging time .... approx. 1 h

Recharger .... JLH-H150-14.4

Nominal consumption ....40 W

Voltage input......100-240 V\~, 50-60 Hz

Voltage output ...... 14,4 V==1500 mA

Protection class ...... □ II

Protection category ...... IPXO

Noise and vibration values have been determined according to the standards and regulations mentioned in the declaration of conformity.

Technical and optical changes may be undertaken in the course of further development without notice. All dimensions, references and information in this instruction manual are therefore not guaranteed. Legal claims made on the basis of the instruction manual can therefore not be considered as valid.

The stated vibration emission value was measured in accordance with a standard testing procedure and may be used to compare one power tool to another.

The stated vibration emission value may also be used for a preliminary exposure assessment.

Warning: The vibration emission value may differ during actual use of the power tool from the stated value depending on the manner in which the power tool is used.

Safety precautions aimed at protecting the user should be based on estimated exposure under actual usage conditions (all parts of the operating cycle are to be considered, including, for example, times during which the power tool is turned off and times when the tool is turned on but is running idle).

Notes on Safety

This section details the basic safety instructions for working with the appliance.

Symbols

Symbols on the Equipment

Read through the instruction manual carefully.

Electrical appliances must not be disposed of with the domestic waste.

nce before changing gear.

Wear eye protection.

Injury hazard caused by rotating tool! Keep hands away.

Symbols on the battery

Do not dispose of batteries in household waste, fire or water.

Do not subject the battery to strong sunlight over long periods and do not leave it on a heater (max. 45°C).

Take batteries to an old battery collection point where they will be recycled in an environmentally friendly manner.

Symbols on the recharger

Caution!

Read the operating instructions before charging.

The recharger is for indoor use only.

Miniature fuse

Protection class II

Electrical appliances must not be disposed of with the domestic waste.

LED display while charging.

Symbols in the manual

Warning symbols with information on damage and injury prevention.

Instruction symbols (the instruction is explained at the place of the exclamation mark) with information on preventing damage.

Help symbols with information on improving tool handling.

General safety instructions for power tools

WARNING! Read all safety directions and instructions.

Omissions in the compliance with safety directions and instructions can cause electrical shock, fire and/or severe injuries.

Retain all safety directions and instructions for future use.

The term „power tool“ in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

1) WORK AREA SAFETY

• Keep work area clean and well lit. Cluttered or dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

2) ELECTRICAL SAFETY

• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.

- Avoid body contact with earthed or grounded surfaces, such as

pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
• Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
• When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
• If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

3) PERSONAL SAFETY

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention white operating power tools may result in serious personal injury.

- Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

• Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
• Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
• If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.

4) POWER TOOL USE AND CARE

• Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
• Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
• Disconnect the plug from the

power source and/or the battery pack from the power tool before making any adjust-ments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

• Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
• Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool's operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
• Hold the device by the insulated gripping surfaces when performing work in which the cutting tool may come into contact with hidden wiring or its own cord. Contact with a live wire can also cause a charge in metal parts of the device and result in an electric shock.

5) CAREFUL HANDLING AND USE OF BATTERY DEVICES

• Charge the batteries only in chargers that are recommended by the manufacturer. Risk of fire if a charger that is suitable for a specific type of battery is used with other batteries.
• In the power tools, use only the batteries designed for the purpose. The use of other batteries may result in injuries and risk of fire.
• Keep the unused battery away from paper clips, coins, keys, nails, screws and other small metal objects, which could cause bridging of the contacts. A short circuit between the battery contacts may cause burns or fire.
• If used incorrectly, liquid may leak from the battery. Avoid contact with this. In the event of accidental contact, rinse off with water. If the liquid gets into eyes, seek medical assistance. Leaking battery fluid may cause skin irritations or burns.

6) SERVICE

• Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

7) SPECIAL SAFETY DIRECTIONS FOR BATTERY-OPERATED TOOLS

• Ensure that the device is switched off before inserting the battery. Inserting a battery into a power tool that is switched on may result in accidents.

• Recharge the batteries indoors

only because the battery charger is designed for indoor use only. Risk of electric shock.

• To reduce the electric shock hazard, unplug the battery charger from the mains before cleaning the charger.
• Do not subject the battery to strong sunlight over long periods and do not leave it on a heater. Heat damages the battery and there is a risk of explosion.
• Allow a hot battery to cool before charging.
• Do not open up the battery and avoid mechanical damage to the battery. Risk of short circuit and fumes may be emitted that irritate the respiratory tract. Ensure fresh air and seek medical assistance in the event of discomfort.
• Do not use non-rechargeable batteries. This could damage the appliance.

Correct handling of the battery charger

• This appliance can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance.
• To charge the battery, use only the charger supplied. Risk of fire and explosion. This ensures that the safety of the device is maintained.
  • Before each use, check the

charger, cable and plug and have them repaired by qualified professionals and only with original parts. Do not use a defective charger and do not open it up yourself. This ensures that the safety of the device is maintained.

- Connect the charger only to a socket with an earth. Ensure that the mains voltage matches the specifications on the charger rating plate. Risk of electric shock.

- Disconnect the charger from the mains before closing or opening connection to the battery / power tool / device. This ensures that the battery and charger are not damaged.

- Keep the charger clean and away from wet and rain. Do not use the charger outdoors. Dirt and the entry of water increase the risk of electric shock.

- Operate the charger only with the appropriate original batteries. Charging other batteries may result in injuries and risk of fire.

- Avoid mechanical damage to the charger. This can result in internal short circuits.

- Do not operate the charger on a combustible surface (e.g. paper, textiles). Risk of fire due to heating during charging.

- If the power cable for this equipment is damaged, it must be replaced by the manufacturer, a customer service agent of the same or a similarly qualified person in order to prevent hazards.

- Do not charge non-rechargeable batteries in the charger. This could damage the appliance.

Additional safety instructions

Warning! Sawing or sanding can result in the formation of hazardous dusts (e.g. arising from materials with paints containing lead, materials containing asbestos, metals or some wood types) which can present a hazard to the operator or persons in the vicinity. Make sure that the workplace is well ventilated. Always wear safety goggles, safety gloves and respiratory protection. Attach a dust extraction system.

- Hold the electric tool by the insulated gripping surfaces when performing work in which the cutting tool may come into contact with hidden wiring. Contact with a live wire can also cause a charge in metal parts of the appliance and result in an electric shock.

- Use suitable detectors in order to find hidden supply lines or ask the local utility company. Contact with electrical cables can lead to electric shock and fire, contact with a gas pipe can result in an explosion. Damage to a water pipe can lead to property damaged and electric shock.

- Secure the workpiece. A workpiece that is retained with clamping appliances or a vice is held more securely than with your hand.

- Be very careful when handling tools such as saws, scraper

GB

blades and drills. These are sharp and present an injury hazard.

- Wear safety gloves when changing attachments. This enables you to avoid injuries if the appliance attachment has heated up after use.

2) SPECIFIC SAFETY INSTRUCTIONS WHEN SAWING

- Keep hands away from the sawing area. Do not reach underneath the workpiece. Always stand to the side of the saw when working. Upon contact with the blade there is a risk of injury.

- Only when the electric tool is turned on should the sawing blade be moved against the workpiece. There is a risk of kick-back if the tool insert jams in the workpiece.

• Make sure that the footplate is securely placed against the workpiece during sawing. The sawblade can tilt and lead to loss of control over the power tool.

- After you have finished work, turn the power tool off and do not pull the sawblade out of the cut until it has come to a standstill. In this way you will avoid any kickback and can safely put down the power tool.

- Use only undamaged saw-blades in perfect condition. Bent or blunt blades can break, adversely affect the cut or cause kickback.

- Do not brake the sawblade after switching the appliance off by applying side pressure. The sawblade may be damaged, break or cause a kickback.

- Tighten the material firmly. Do not support the workpiece by hand or foot. Do not touch any objects or the ground with the saw running. There is a risk of kickback. - Hold the power tool tightly with both hands while working and ensure a secure footing. The power tool is guided more securely with both hands.

- Wait until the power tool has stopped before placing it down. The tool insert can tilt and lead to loss of control over the power tool.

- Switch the appliance off immediately if the sawing blade jams. Spread the saw cut out and pull the blade out carefully. This can lead to loss of control over the power tool.

3) SPECIAL SAFETY INFORMATION DURING SANDING AND SCRAPING

- Only use the power tool for dry sanding. Do not scrape moist materials. Penetration of water into the power tool increases the risk of electric shock.

- Avoid overheating the sanded object and the sander itself. Possible fire hazard.

- The workpiece gets hot during grinding. Do not touch the machined area, allow it to cool down. There is a risk of burning. Do not use coolants or the like.

• Always empty the dust container before work breaks. Sanding dust in the dust sack, micro filter, paper sack (or in the filter sack or extraction system filter) can self-ignite under unfavourable conditions such as flying sparks caused by grinding

metals. Particular hazards are caused if the sanding dust is mixed with paint, polyurethane residues or other chemical substances, or if the sanded object is hot after long working periods.

4) RESIDUAL RISKS

Even if properly operating and handling this electric tool, some residual risks will remain. Due to its construction and build, this electric tool may present the following hazards:

a) Lung damage, if suitable respiratory protection is not worn;
b) Cuts
c) Ear damage if working without ear protection.
d) Eye damage if suitable eye protection is not worn.
e) Damage to your health caused by swinging your hands and arms when operating the appliance for longer periods of time or if the unit is not held or maintained properly.

Charging the battery

Do not expose the battery to extreme conditions such as heat or impact. Risk of injury from escaping electrolytic solution! After eye/skin contact, rinse the affected areas with water or a neutraliser and consult a doctor.

Charge the battery in a dry room only. Prior to attaching the charger, check that the battery's outer surface is clean and dry. There is a risk of injury due to electric shock.

Only use the charger from the package to charge the battery. Mind not to charge the appliance for more than 1 hour at a time. If you do, the battery and the appliance may be damaged and longer charging times would be a waste of energy. Excessive charging will void the warranty.

• Charge the battery before the first time of use. Do not briefly charge the battery several time in a row.
• If a fully recharged battery lasts for considerably shorter operating times, the battery is used up and needs to be replaced. Only use an OEM spare battery available from our Customer Service.
• Always take heed of the applicable safety instructions as well as the environmental protection regulations and information.
• The warranty excludes all defects caused by improper handling.

Remove/insert rechargeable battery

1. To remove the battery (9) from the appliance, press the release button (10) on the battery and pull the battery out.

2. To insert the battery (9) push the battery along the guide rail into the appliance. It locks into place audibly.

Recharging the battery

1. Remove the battery (9) from the appliance.

2. Slide the rechargeable battery (9)

GB

onto the charger (15). It locks into place audibly.

1. Plug the charger (15) into an electrical outlet.
2. After the charging process, disconnect the charger (15) from the mains supply.
3. Pull the rechargeable battery (9) out of the charger (15).

Overview of the LED indicators (15a) on the charger (15):

green LED flashes:

Charger is connected to the mains without a battery.

red LED lights up:

Battery charging.

green LED lights up:

Battery is charged.

Used batteries

• If a fully recharged battery lasts for considerably shorter operating times, the battery is used up and needs to be replaced. Only use an OEM battery pack replacement available from our Customer Service.
• Always take heed of the applicable safety instructions as well as the environmental protection regulations and information (see "Waste Disposal and Environmental Protection").

Checking the charge status of the rechargeable battery

The battery charge status indicator (9a) signalises the state of charge of the battery (9).

Press the button (9b) on the battery (9). The state of charge of the battery is displayed by illuminating the 3-colour LED lights of the state of charge display (9a).

All LEDs are on: Battery is fully charged.

Red and yellow LEDs are on: Battery has a residual charge (< 90 %).

Red LED lights up: Battery is empty, please charge.

Operation

Replacing the appliance attachment

Secure the appliance against switching on (see "Switching on/off") or remove the rechargeable battery from the appliance. There is an injury hazard if the device is switched on accidentally.

Wear safety gloves. The appliance attachment might have heated up after use.

Removing appliance attachment

1. Push the unlocking lever (5) into position □ as far as the stop and then hold it in this position.
2. Pull the unlocked appliance attachment off (4/17/23/26).
3. Allow the unlocking lever (5) to slide back into position ☐.

Fitting appliance attachment

1. Push the appliance attachment (4/17/23/26) along the guide rail into the motor unit (6). It locks into place audibly.

2. Allow the unlocking lever (5) to slide back into position ☐.

3. Check that the appliance attachment is secure by pulling on it.

Switching on/off

1. Switching on: Press the on/off switch (A 11).

By using the on/off switch ( A 11) you can progressively control the speed.

Gentle pressure: low speed Increase pressure: higher speed.

1. Switching off: Release the on/off switch (A 11).

If you place the direction switch (A 7) in the middle position, the device is secured against being switched on.

Motor unit with drill attachment PKGA1

Changing the tool

Secure the appliance against switching on (see "Switching on/off"). If the appliance is switched on accidentally, there is a danger of injury.

1. Rotate the keyless chuck (1) counter-clockwise, until the drill chuck aperture is large enough to accommodate the tool.

2. Insert the tool as far as possible into the keyless chuck (1).

3. Rotate the keyless chuck (1) clockwise in order to clamp the tool.

4. To remove the tool again, rotate the keyless chuck (1) and pull out the tool.

Choice of gear

Stop appliance before changing gear.

1. Wait for the appliance to come to a standstill.
   2 Slide the gear selector (A 3) into the required position:
   1: low speed preselection.
   2: high speed preselection.

Set the direction of rotation

The appliance's direction of rotation can be changed with the rotational direction switch.

1. Wait for the appliance to come to a standstill.

2. Push the rotational direction speed (A 7) into the desired position:
   Clockwise rotation: → to drill and screw in screws.
   Anticlockwise rotation: ← to un- screw screws.

3. If you place the direction switch (A 7) in the middle position, the device is secured against being switched on.

The direction change may only be actuated when at a standstill!

Torque adjustment

You can preselect the maximum torque. The torque settings are labelled 1 - 19 +

1. Wait for the appliance to come to a standstill.
2. Turn the torque adjusting ring (2) to select the desired torque:

Screws: Steps 1 - 19

Drilling: Step

GB

1. Start with a lower torque step and increase as required.

The direction change may only be actuated when the appliance is at a standstill!

The necessary torque is dependent on:

• the type and hardness of the material to be treated;
• the type and length of the screws used.

Motor unit with multi-sander attachment PKGA2

Secure the appliance against switching on (see "Switching on/off"). If the appliance is switched on accidentally, there is a danger of injury.

Attaching/removing sanding sheet

The sanding plate (22) is fitted with Velcro for rapid attachment of the sanding sheet.

Attaching sanding sheet

1. Press the sanding sheet (24) evenly onto the sanding plate (22). Ensure that the holes in the sanding sheet are placed above the openings in the sanding plate.

Removing sanding sheet

1. Simply pull the sanding sheet (24) off the sanding plate (22).

Connecting dust extraction

You can reduce dust production during sanding by attaching a dust extraction system.

1. Push the adaptor (25) into the opening on the multi-sander attachment (23) as far as the stop.

2. Connect a dust extractor suction hose to the adaptor (25).

Motor unit with sabre saw attachment PKGA3

Installing/changing the blade

Secure the appliance against switching on (see "Switching on/off"). If the appliance is switched on accidentally, there is a danger of injury.

Wear gloves when handling the sawblade. In this way, you avoid injury from cuts.

Caution, risk of Injury!

• Do not use any blunt or bent blades or blades which are damaged in any other way.
• Always insert a suitable saw-blade.

An overview of appropriate blades can be found in "Spare Parts/Accessories".

Installing the blade:

1. Push the lever (19) for sawblade unlocking upwards as far as the stop. Push the sawblade shaft (20/21) into the sawblade mounting slot.

2. To unlock, release the lever (19), it will return to the initial position.

3. Check that the sawblade is secure by pulling on it.

Removing the sawblade:

1. Press the lever (19) for sawblade unlocking upwards as far as the stop and then pull the sawblade out of the sawblade mounting.

For certain work, the sawblade can also be inserted after turning through 180°.

Operating the sabre saw

1. Before switching the appliance on, ensure it is not in contact with the workpiece.
2. Turn the appliance on.

By using the on/off switch (A 11) you can progressively control the stroke rate.

Gentle pressure: low stroke rate.

Greater pressure: higher stroke rate.

The on/off switch cannot be locked.

1. Place the footplate (A 18) on the workpiece.
2. Cut with a uniform forward motion.
3. After completion of the work, first remove the blade from the saw cut and then switch the appliance off.

Motor unit with multifunction tool PKGA4

Changing the tool

Secure the appliance against switching on (see "Switching on/off"). If the appliance is switched on accidentally, there is a danger of injury.

1. Push the lever (27) for tool unlocking upwards as far as the stop.

2. Pull the unlocked tool holder (29) off forwards.

3. Place the required tool (30/32/33) on the arbor (28). 12 different positions are possible.
4. Press the tool holder (29) back into the central mounting.
5. Push the lever (27) for tool un-locking forwards again. The tool holder is fixed to the tool.

Attaching/removing sanding sheet

The delta sanding plate (30) is fitted with Velcro for rapid attachment of the sanding sheet.

Attaching sanding sheet

1. Press the sanding sheet (31) evenly onto the delta sanding plate (30). Ensure that the holes in the sanding sheet are placed above the openings in the sanding plate.

Removing sanding sheet

1. Simply pull the sanding sheet (31) off the delta sanding plate (30).

Practical tips

When working with the appliance, always wear suitable clothing and appropriate protective equipment.

Prior to each use it must be ensured that the appliance is working correctly.

Personal protective equipment and a fully functional appliance reduce the risk of injuries and accidents.

Sawing

Wear eye protection.

• Use only undamaged sawblades in perfect condition. Only use metal saw-blades for metalworking.
• Ensure your stance is stable and hold the appliance tightly with both hands and away from your body.
• Before sawing the workpiece, check for hidden foreign objects such as nails, screws. These must be removed.
• Plunge cuts may only be made in soft material such as wood or plasterboard.

Selection of sawblade

Wood sawblade	for wood, plastic, plaster-board
Metal sawblade	for metal sheets, profiles and tubes
Plunge sawblade	for soft materials like wood or plasterboard

Sanding

• Use a dust extraction system when sanding with the multi-sander attachment.
• Move the appliance against the workpiece once it is switched on.
• Clean the sanding plate before you attach a sanding sheet.
• Only work with sanding sheets in perfect condition to achieve good sanding results.
• Work using low and even pressure. This protects the appliance and the sanding sheet.
• Do not use the same sanding sheet to sand different materials (e.g. metal and then wood).

Selection of sanding sheet

Grain size Application
60	for pre-sanding rough wood surfaces
80 / 120 for plain sanding
240	for fine sanding of primed and painted surfaces

Scraping

• Use a high oscillation rate when scraping.
• Work using low pressure and at a low angle in order not to damage the substrate material.

Cleaning/Maintenance

Repair and servicing work not described in this manual should always be carried by our Service Centre. Use only original parts.

Switch off the device and remove the battery from the device before working with or transporting it.

The following cleaning and servicing should be done regularly. This will ensure a long and reliable service life.

Cleaning

Do not spray the appliance with water and do not immerse it in water. Electric shock hazard!

• Keep clean the ventilation slots, motor housing and handles of the appliance. Use a damp cloth or a brush.
  Do not use cleaning agents or solvents. You may otherwise irreparably damage the appliance.

Maintenance

- The equipment is maintenance free.

Storage

• Store the device in a dry place well out of reach of children.
• Remove the battery before storing the unit for longer periods of time (e.g. hibernation).
• Store the battery only in a partially charged state. The state of charge should be 40 – 60 % over a longer storage period (two LED lights of the charge status indicator (D 9a) light up).
• During a longer storage period, check the state of charge of the battery and recharge if necessary roughly every 3 months.
• In order to keep the battery well charged, avoid exposing the appliance

to extreme heat or cold in storage.

- Store the equipment between 10^irc C and 25^irc C. During storage, avoid extreme cold or heat so the battery does not lose power.

Waste Disposal/Environmental Protection

Remove the battery from the device and take the device, battery, accessories and packaging for environmentally friendly recycling.

Electric units do not belong with domestic waste.

Do not dispose of batteries in household waste, fire (risk of explosion) or water. Damaged batteries may damage the environment and your health if toxic fumes or liquids leak out.

• Return the unit and the recharger to a recycling centre. The plastic and metal parts employed can be separated out and thus recycled use can be implemented. Ask our Service-Center for details.
• Dispose of batteries in discharged condition. We recommend covering the pole with adhesive tape to prevent a short circuit. Do not open up the battery.
• Dispose of batteries in accordance with the local regulations. Take batteries to an old battery collection point where they will be recycled in an environmentally friendly manner. For information about this, ask your local waste management company or our service centre.
• Defective units returned to us will be disposed of for free.

Guarantee

Dear Customer,

This equipment is provided with a 3-year guarantee from the date of purchase. In case of defects, you have statutory rights against the seller of the product. These statutory rights are not restricted by our guarantee presented below.

Terms of Guarantee

The term of the guarantee begins on the date of purchase. Please retain the original receipt. This document is required as proof of purchase.

If a material or manufacturing defect occurs within three years of the date of purchase of this product, we will repair or replace – at our choice – the product for you free of charge. This guarantee requires the defective equipment and proof of purchase to be presented within the three-year period with a brief written description of what constitutes the defect and when it occurred. If the defect is covered by our guarantee, you will receive either the repaired product or a new product. No new guarantee period begins on repair or replacement of the product.

Guarantee Period and Statutory Claims for Defects

The guarantee period is not extended by the guarantee service. This also applies for replaced or repaired parts. Any damages and defects already present at the time of purchase must be reported immediately after unpacking. Repairs arising after expiry of the guarantee period are chargeable.

Guarantee Cover

The equipment has been carefully produced in accordance with strict quality guidelines and conscientiously checked prior to delivery.

The guarantee applies for all material and manufacturing defects. This guarantee does not extend to cover product parts that are subject to normal wear and may therefore be considered as wearing parts (e.g. saw blade, battery) or to cover damage to breakable parts (e.g. switches).

This guarantee shall be invalid if the product has been damaged, used incorrectly or not maintained. Precise adherence to all of the instructions specified in the operating manual is required for proper use of the product. Intended uses and actions against which the operating manual advises or warns must be categorically avoided.

The product is designed only for private and not commercial use. The guarantee will be invalidated in case of misuse or improper handling, use of force, or interventions not undertaken by our authorised service branch.

Processing in Case of Guarantee

To ensure quick handling of you issue, please follow the following directions:

• Please have the receipt and identification number (IAN 110037) ready as proof of purchase for all enquiries.
• Please find the item number on the rating plate.
• Should functional errors or other defects occur, please initially contact the service department specified below by telephone or by e-mail. You will then receive further information on the processing of your complaint.
• After consultation with our customer service, a product recorded as defective

can be sent postage paid to the service address communicated to you, with the proof of purchase (receipt) and specification of what constitutes the defect and when it occurred. In order to avoid acceptance problems and additional costs, please be sure to use only the address communicated to you. Ensure that the consignment is not sent carriage forward or by bulky goods, express or other special freight. Please send the equipment inc. all accessories supplied at the time of purchase and ensure adequate, safe transport packaging.

Repair Service

For a charge, repairs not covered by the guarantee can be carried out by our service branch, which will be happy to issue a cost estimate for you. We can handle only equipment that has been sent with adequate packaging and postage.

Attention: Please send your equipment to our service branch in clean condition and with an indication of the defect.

Equipment sent carriage forward or by bulky goods, express or other special freight will not be accepted.

We will dispose of your defective devices free of charge when you send them to us.

Service-Center

Service Great Britain

Tel.: [phone]

(£ 0.10/Min.)

E-Mail: [e-mail]

IAN 110037

Importer

Please note that the following address is not a service address. Please initially contact the service centre specified above.

Spare Parts/Accessories

Spare parts and accessories can be obtained at www.grizzly-service.eu

If you do not have internet access, please contact the Service Centre via telephone (see "Service-Center" Page 21). Please have the order number mentioned below ready.

Position instruction manual

Position exploded drawing

Description

Order No.

A 4 PKGA1 Drill attachment 91104151
A 9	18	Battery	80001121
A 15 19	Charger EU	80001021
A 17	PKGA3	Sabre saw attachment	91104153
A 20	PKGA3-1	Metal sawblade (HSS 150 mm/18 TPI*)	13800222
A 21	PKGA3-11	Wood sawblade (HCS 150 mm/6 TPI*)	13800221
A 23	PKGA2	Multi-sander attachment	91104154
A 24	PKGA2-8	Sanding sheets for multi-sander attachment(2 x 60, 2 x 120, 1 x 240)	30211066
A 25	PKGA2-9	Dust extraction adaptor	91104150
A 26	PKGA4	Multifunction tool	91104152
A 31		Sanding sheets for delta sanding plate(1 x 60, 1 x 80, 1 x 120)	30211067
A 32		Scraper blade	30220080
A 33		Plunge sawblade	30220081

* HSS = High Speed Steel

* HCS = High Carbon Steel, steel with high carbon content

Further accessories are available from the trade for every possible application purpose.

Trouble Shooting

Problem Possible Cause Error correction
Appliance doesn't start	Rechargeable battery (A9) discharged	Charge rechargeable battery(see „charging process“)
	Rechargeable battery (A9) not inserted	Insert rechargeable battery(see „charging process“)
	On/off switch (A 11) is broken	Repair by Service Centre
Appliance works with interruptions	Internal lose contact	Repair by Service Centre
	On/off switch (A 11) is broken
Tool does not move although the motor is running	Appliance attachment or tool not correctly mounted	Fit the appliance attachment or tool correctly (see „Operation“)
Low appliance power	Tool unsuitable for the workpiece to be worked on	Insert a suitable tool
	Tool blunt or worn down Insert a new tool
	Incorrect speed Adjust speed
	Low battery power	Charge battery (A 11)(see „Charging process“)
Tool wears down quickly	Tool unsuitable for the workpiece to be worked on	Insert a suitable tool (see „Operation“)
	Too much pressure applied Reduce the pressure
	Speed too high Reduced speed

Sadržaj

Uvod....24

Svrha primjene 24

Opći opis 25

Obim isporuke....25

Pregled 25

Tehnički podatci 26

Sigurnosne upute 27

Akumulator (Li-Ion)....PAP14.4

* HSS = High Speed Steel

HCS = High Carbon Steel, oțel cu continut ridicat de carbon

* The object of the declaration described above satisfies the provisions of Directive 2011/65/EU of the European Parliament and the Council of 8 June 2011 on limiting the use of certain harmful substances in electrical and electronic appliances.
** The last two digits of the year in which the CE marking was affixed.