Water Computer C 1030 plus - Irrigation timer GARDENA - Free user manual and instructions

Product Type	Water Computer / Irrigation Timer
Dimensions (approx.)	120 x 80 x 60 mm
Weight	200 g
Power Supply	9 V battery (alkaline recommended)
Battery Life	Up to 6 months with normal use
Number of Programs	1 program with multiple start times
Watering Duration Range	1 minute to 99 minutes per cycle
Interval Watering	Every 1 to 7 days
Rain Delay Function	Yes, adjustable 1-7 days
Manual Watering Override	Yes
Display	LCD with time and settings
Hose Connection	G1" female thread (standard garden hose)
Maximum Water Pressure	10 bar (145 psi)
Waterproof Rating	IPX4 (splash-proof)
Operating Temperature	5°C to 40°C
Storage Temperature	-10°C to 50°C
Maintenance	Clean filter regularly; remove battery during winter storage
Safety	Designed for outdoor use; do not immerse in water
Spare Parts	Replacement filter, battery cover, and o-rings available
Warranty	2 years (check local terms)

Frequently Asked Questions - Water Computer C 1030 plus GARDENA

How do I set the current time on the Water Computer C 1030 plus?

Press the Time button and use the + and - buttons to adjust hours and minutes. Confirm with the OK button.

How do I program a watering schedule?

Press the Program button to enter programming mode. Set the start time, duration (1-99 minutes), and frequency (daily or interval days). Press OK to save.

What type of battery does the device use?

It uses a standard 9V alkaline battery. A fresh battery typically lasts an entire watering season.

Can I manually water without affecting the programmed schedule?

Yes, press the Manual button to start watering for a specific duration (1-99 minutes). The programmed schedule will resume automatically.

How does the rain delay function work?

Press the Rain Delay button and set a delay period (1-7 days). The device will skip all watering cycles during that time and resume automatically.

What should I do if the display is blank?

Check if the battery is correctly installed or replace it. If the problem persists, remove the battery for 30 seconds and reinsert it to reset the device.

How do I clean the water computer?

Disconnect the device from the hose. Remove the filter and rinse it under running water. Wipe the exterior with a damp cloth. Do not use solvents.

Can I use the water computer with a drip irrigation system?

Yes, it is compatible with most garden irrigation systems, including drip lines, soaker hoses, and sprinklers. Ensure the flow rate does not exceed the device's capacity.

What should I do in winter to protect the device?

Remove the battery and store the device indoors at a frost-free location. Also, disconnect it from the hose to prevent freeze damage.

Where can I find spare parts or replacements?

Spare parts such as filters, o-rings, and battery covers are available from Gardena authorized dealers or online. Use the model number C 1030 plus when ordering.

USER MANUAL Water Computer C 1030 plus GARDENA

GB Operating Instructions

Water Computer

F Mode d'emploi

Welcome to the Garden of GARDENA...

Translation of the original instructions from German. Please read these operating instructions carefully and observe the notes given. Use these instructions to familiarise yourself with the Water Computer and its proper use as well as the notes on safety.

For safety reasons, children and young people under 16 as well as anyone who is not familiar with these operating instructions should not use the Water Computer.

→Please keep these operating instructions in a safe place.

Contents

1. Where to Use Your GARDENA Water Computer ....2
2. Safety Instructions .... 2
3. Function 3
4. Putting Your Water Computer into Operation ....5
5. Programming 6
6. Putting Your Water Computer out of Operation 10
7. Maintenance .... 10
8. Troubleshooting .... 11
9. Available Accessories 11
10. Technical Data 12
11. Service / Warranty 12

1. Where to Use Your GARDENA Water Computer

Intended use:

The GARDENA Water Computer is intended for private use in domestic and hobby gardens, exclusively for outdoor use, to control sprinklers and watering systems.

The Water Computer can be used for automatic watering during holidays.

Please note:

The GARDENA Water Computer must not be used for industrial purposes or in conjunction with chemicals, foodstuffs, easily flammable and explosive materials.

2. Safety Instructions

Battery:

To ensure the Water Computer runs safely, only a 9V alkaline manganese battery (alkaline) type IEC 6LR61 must be used.

In order to stop the Water Computer from failing because of a weak battery if you are away for a long time, the battery must be replaced when the battery display still shows only 1 bar.

Setting up

Warning!

The Water Computer must not be used indoors.

Only use the Water Computer outdoors.

The Water Computer may only be set up vertically with the sleeve nut to the top to prevent water from penetrating into the battery compartment.

The minimum water output to ensure that the Water Computer functions correctly is 20 - 30 l/h.

For example, at least 10 x 2-litre Drip Heads are required to control the Micro-Drip-System.

At high temperatures (over 60 °C at the display) the LCD display may extinguish. This does not affect the program in any way. When the computer cools down the LCD display illuminates again.

The max. temperature for the water flow is 40 °C.

Only use clear fresh water.

The minimum operating pressure is 0.5 bar, the maximum operating pressure is 12 bar.

Avoid tensile strain.

Do not pull the hose connected to the Water Computer.

Programming

Program the Water Computer with the tap turned off.

In this way you can avoid getting wet when trying out the manual On / Off function (man. On/Off). You can remove the control unit from the housing to program the Water Computer.

If the controller is removed when the valve is open, the valve remains open until the controller is fitted again.

3. Function

Controls:

Display levels:

With the Water Computer, the garden can be watered fully automatically up to 3 times a day at any time of day (every 8 hours). Sprinklers, a sprinkler system or a drip head watering system can be used for watering.

The Water Computer carries out watering fully automatically according to the set program and can therefore also be used during holidays. Early in the morning or late in the evening, evaporation and therefore water consumption is lowest.

The watering programme is easily entered using the controls.

Control Function

① Rotary button Changes the adjustable values. ② OK button Applies the values set with the rotary button. ③ Menu button Changes to the next programme level. ④ Man. button For switching the water throughput on or off manually.

The 6 display levels,

• Level 1: Normal display • Level 2: Current time and day of the week • Level 3: Watering start time • Level 4: Watering duration • Level 5: Watering frequency • Level 6: Switches programme on and off

can be selected one after the other by pressing the Menu key.

You can change the display level at any time, even during programming. All the programme data which have been confirmed up to that point with the O.K. key are stored.

Display

Display	Description
5 Weekdays Current weekday or programmed (Mo), (Tu), ... watering days.
6 Time Flashes when in input mode for the current data (hours, minutes, day of the week).
7 am / pm Display for 12 hour clock (e. g. in USA, Canada).
8 Start Flashes when in input mode for watering start time.
9 Run Time Watering duration (flashes when in input mode).
10 8h, 12h, 24h, 2nd, 3rd, 7th	Watering cycle (with drop symbol activated). Every 8 / 12 / 24 hours; every 2nd / 3rd / 7th day.
11 Prog ON / OFF	Watering programme on (ON) / off (OFF).
12 Automatic mode sensor	Watering is controlled automatically via the sensor.
13 Sensor ON / OFF	Sensor ON (watering) / Sensor OFF (watering is not carried out).
14 Battery [11]	Indicates 5 battery levels:3 bars: Battery fully charged2 bars: Battery half full1 bar: Battery low1 bar flashing: Battery almost flat0 bar: Battery flat

If no bars are displayed, the valve is no longer opened. A valve opened by the programme will also close again if the battery is flat. The battery display is reset when the battery is changed.

2 Bars	1 Bar	1 Bar flashing	0 Bar
Battery half full	Battery low	Battery almost flat	Battery flat
Valve opens.	Valve opens.	Valve still opens.	Valve does not open.
The Water Computer is guaranteed to work for a minimum of 4 more weeks.	The Water Computer will continue to work for no more than 4 weeks.	The Water Computer stops working soon.	The Water Computer stops working.
	It is advisable to change the battery.	The battery must be changed soon.	The battery must be changed.
	→ Replace battery (see 4. Putting Your Water Computer into Operation “Inserting battery”).

4. Putting Your Water Computer into Operation

Insert battery:

The Water Computer must only be operated with a 9 V alkali-manganese (alkaline) battery type IEC 6LR61.

1. Remove controller ⑮ from the housing of the Water Computer.
2. Insert battery in the battery compartment ⑯. Observe correct polarity Ⓟ. The display shows all the LCD-symbols for 2 seconds and then moves to the time / day of week level.
3. Install controller ⑮ on the housing again.

Connect Water Computer:

The Water Computer is fitted with a sleeve nut ⑰ for taps with (G 1") (33.3 mm) thread. The adaptor supplied ⑱ allows the Water Computer to be connected to taps with a (G 3/4") thread (26.5 mm).

1. For tap with a G 3/4" (26.5 mm) thread: Screw adaptor ⑱ on to the tap manually (do not use pliers).
2. Screw sleeve nut ⑰ of the Water Computer on to the adaptor thread by hand (do not use pliers).
3. Screw tap connector ⑲ on to the Water Computer.

Connect soil moisture or rain sensor (optional):

Apart from scheduled watering there is also the option of including how damp the soil is or rainfall into the watering programme.

If the soil is damp enough, the programme will be stopped, or a programme will be prevented from starting. Manual operation via Man. On / Off is unaffected by this.

The "Soil moisture sensor-controlled watering" mode can only be selected when using a soil moisture sensor.

1. Remove controller ⑮ from the housing of the Water Computer.
2. Place soil moisture sensor in the watered area
3. or - place rain sensor (with extension cable if necessary) outside the watered area.
4. Insert the sensor in the sensor connection ⑳ of the Water Computer.

An adapter cable may be required to connect older sensors, which can be purchased from GARDENA Service, GARDENA Adapter cable Art. No. 1189-00.600.45.

Fit anti-theft device (optional):

To secure your Water Computer against theft, you can obtain the GARDENA Anti-theft device Art. No. 1815-00.791.00 from GARDENA Service.

1. Screw clamp ② with screw ② firmly to the back of the Water Computer.
2. Use clamp ② e.g. for fixing a chain.

It is no longer possible to remove the screw after it has been screwed in.

5. Programming

Set current time and day of week: [Level 2]

To set the programme, the controller can be removed and mobile programming can be carried out (see 4. Putting Your Water Computer into Operation "Inserting battery").

1. Press the Menu key (not necessary if the battery has just been inserted). The hours display and time flash.
2. Set the time in hours with the rotary button (example: 9 hours) and confirm with the OK key. Time and the minutes display flash.
3. Set the time in minutes with the rotary button (example: 300 minutes) and confirm with the OK key. Time and the day of the week display flash.
4. Set the day of the week with the rotary button (example: Sa for Saturday) and confirm with the OK key. The display moves to the message "Insert watering programme." Start and the hour display will flash on the screen.

4. Watering modes:

The water computer has 2 watering modes:

• Scheduled watering using the input programmes (watering starts depending on the watering start time) - or -
• Soil moisture sensor-controlled watering using a GARDENA soil moisture sensor (watering begins when the soil moisture sensor registers dry).

Entering watering programme:

[Level 3]

1.

2.

3.

[Level 4]

4.

5.

[Level 5]

6.

7.

Scheduled watering:

1. Press Menu-key twice (not necessary if the current time and day of the week has been entered).

Start Prog and the hours section flash on the display.

1. Set the watering start time hours with the rotary button (e.g., 6) and confirm with the OK-key.

Start Prog and the minute display flashes on the screen.

1. Set the minutes for starting the watering time with the rotary button (example: 20 minutes) and confirm with the OK-key.

Run Time and the hours for the watering time flash on the display.

1. Set the hours for the watering time with the rotary button (example: 0 hours) and confirm with the OK-key.

Run Time and minutes for the watering time flash on the display.

1. Set watering time minutes with the rotary button (example: 17 minutes) and confirm with the OK-key.

Watering cycle ♦ 8h flashes on the display.

The watering frequency can be selected by:

- the (6.) watering cycle (right hand column of the display) – or –

• the (7.) watering days (left hand column of the display).

1. Select watering cycle with the rotary button (E.g. 2nd) and confirm by pressing OK.

8h / 12h / 24 h: Watering every 8 / 12 / 24 hours

2nd / 3rd / 7th: Watering every 2nd / 3rd / 7th day

The display jumps to the watering programme on the screen.

-or-

7. Select each watering day with the rotary button

(E.g. ♦ Mo, ♦ Fr Monday and Friday) and confirm by pressing OK. Press the Menu button.

The display jumps to the watering programme on the screen.

Starting watering programmes: [Level 6]

The Prog 00N must be selected so that the watering programme can start.

1. Press the Menu button 5 times (not necessary if the programme has been created before).
2. Select the Prog 80 with the rotary button and confirm by pressing OK.

The Prog 00 appears for 2 seconds and then the Normal display returns.

The water computer has now been programmed, i.e. the inbuilt valve opens and closes completely automatically and thus waters at the programmed time.

Even if Prog OFF is selected, watering can be done manually.

Soil moisture sensor-controlled watering

Condition: the GARDENA Soil Moisture Sensor Art. 1188 is connected.

A previously set scheduled watering programme is retained but not carried out.

1. Hold the Menu button down for 5 seconds. The watering cycle flashes.
2. Select the required watering cycle with the rotary button (e.g. play) and confirm with the OK-key.

Day

Watering during the day (6 a.m. - 8 p.m.) when the soil moisture sensor registers dry.

Night

Watering during the night (8 p.m. - 6 a.m.) when the soil moisture sensor registers dry.

Day & Night

Watering when the soil moisture sensor registers dry.

1. Set the watering duration in minutes (0 – 59 minutes) with the rotary button (E.g. 40 minutes) and confirm by pressing OK. Watering starts in the set watering cycle as soon as the soil moisture sensor registers dry (Sensor ON).

The watering duration set in the sensor-controlled watering mode also applies to manual watering.

In the case of soil moisture sensor-controlled watering, a two-hour watering pause is triggered after every watering cycle in order for the soil moisture sensor to record the soil moisture.

Example:

Watering cycle = (Day), watering duration = 40 minutes.

Watering begins when the sensor registers dry (Sensor ON) during the day (between 6 a.m. and 8 p.m.) and ends up to 40 minutes later depending on the amount of moisture in the soil.

The watering duration is preset to 30 minutes at the factory.

Emergency programme: If no sensor is inserted in sensor-controlled watering mode or if the connection cable is faulty, watering will take place every 24 hours. The watering duration depends on the run time but is limited to a maximum of 30 minutes.

Read / modify watering programmes:

If a value in the programme is to be changed, this can be changed without changing the other values in the programme.

1. Press the Menu key twice. Start and the hours flash on the display.
2. Press the Menu button to jump to the next programme level - or - change the programme data with the rotary button and confirm by pressing the OK button.

When the watering duration is changed while a program is running, the current watering cycle is ended.

Manual operation:

The valve can be opened or closed manually at any time.

A program-controlled open valve can also be closed early without changing the program data (watering start time, watering duration and watering frequency).

The controller must be fitted.

1.

1. Press the Man. key to open the valve manually (or to close an open valve).

Run Time and the watering time in minutes (set to 300 minutes in the factory) flash for 10 seconds on the display.

1. While the watering time in minutes is flashing, the watering duration can be modified with the rotary button (between 0800 and 0855) (example: 170 minutes) and confirm with the OK key.
2. Press the Man. key to close the valve early. The valve is closed.

The amended manual opening period is stored, i.e., each time the valve is opened manually in the future, the modified opening period is preset. If the manual opening period is amended to 0800, the valve is closed and also remains closed after the Man. key is pressed (child lock).

If the valve has been opened manually and a programmed start of a watering period overlaps the manual opening period, the programmed starting time is suppressed.

Example:

The valve is opened at 9:00 a.m. manually, the opening period is 30 minutes. A program with a start time (START) between 9:00 and 9:30 a.m. will not be undertaken in this case.

Reset:

The factory settings are restored.

→ Press the Man. key and Menu key simultaneously for 3 seconds. All the LCD symbols are displayed for 2 seconds and the display moves to the normal display.

• All the program data are set to zero. •The manual watering period is set to 0030 again. •The time and day of the week are retained.

Important information:

If no entry is made during programming for a period of more than 60 seconds, the normal display reappears. In this case all changes made up till now will be applied.

When a sensor installed in the water computer registers damp (OFF), the programmed watering is not carried out.

6. Putting Your Water Computer out of Operation

Storage / Overwintering:

1. Press Menu-key 5 times, select Prog. OFF with the rotary button and confirm with the OK-key. The watering program is not run.
2. Store your Water Computer in a dry place where it is protected from frost.

Disposal: (in accordance with RL2002/96/EC)

The product must not be added to normal household waste. It must be disposed of in line with local environmental regulations.

→Important: Make sure that the unit is disposed of via your municipal recycling collection centre.

Disposing of flat batteries:

→Please return flat batteries to a GARDENA dealer or dispose of them properly at your nearest recycling centre.

Only dispose of batteries when they are flat.

7. Maintenance

Clean filter :

The filter ②3 should be checked regularly and cleaned when necessary.

1. Unscrew sleeve nut ⑰ of the Water Computer by hand from the tap thread (do not use pliers).
2. If necessary unscrew the adaptor ⑱.
3. Remove filter ②3 from sleeve nut ⑰ and clean.
4. Fit the Water Computer again (see 4. Putting Your Water Computer into Operation "Connecting Water Computer").
5. Troubleshooting

Fault	Possible	Cause
No display appears	Battery inserted incorrectly.	→ Check polarity markings match (+/-).
	Flat battery. →Insert new (alkaline) battery.
	Temperature on the display Display appears after is higher than 60 °C. temperature has dropped.
Manual watering is not possible using the Man. button	Battery flat (1 bar flashes).	→ Insert new (alkaline) battery.
	Manual watering period is set to 0:00.	→Set manual watering period to a figure greater than 0:00 (see 5. Programming).
	Tap turned off.	→Turn tap on.
Watering program is not being undertaken (no watering)	Watering program has not been entered completely.	→ Read off watering program and modify if necessary.
	Programs deactivated (Prog. OFF).	→ Activate program (Prog. ON).
	Program entry/modification during or just before the start pulse.	→ Make program entry/ modification outside the programmed start times.
	Valve was opened manually →Avoid previously.	→ Avoid possible program overlaps.
	Tap turned off.	→Turn tap on.
	Soil moisture or rain sensor registers damp.	→If dry, check setting/ location of soil moisture/ rain sensor.
	Battery flat (1 bar flashing).	→ Insert new (alkaline) battery.
Water Computer does not close	Minimum quantity of water drawn is less than 20 l/h.	→ Connect more drip heads.
All 3 watering cycle symbols flash (※ ▶ ▷)	Sensor not correctly connected.	→ Check connection cable and sensor.

In the event of other faults please contact GARDENA Service. Repairs should only be carried out by GARDENA service centres or dealers authorised by GARDENA.

1. Available accessories

GARDENASoil Moisture Sensor	Art. No.
GARDENARain Sensor electronic	Art. No. 1189
GARDENA Anti-theft device	Art. No. 1815-00.791.00From GARDENA Service

GARDENA For simultaneous connection of From GARDENA Service

Cable Adapter rain and soil moisture sensor

10. Technical Data

Min./max. operating pressure: 0.5 bar / 12 bar

Flow medium: Clear fresh water

Max. liquid temperature: 40 °C

Number of program-controlled watering cycles per day: 3 x (every 8 hrs.), 2 x (every 12 hrs.), 1 x (every 24 hrs.)

Number of program-controlled watering cycles per week: Every day, every 2, 3 or 7 days; or individual selection of weekdays

Watering duration: 1 min. to 7 hours 59 min.

Battery required: 1 × 9V alkaline manganese (alkaline) battery type IEC 6LR61

Operating time of the battery: approx. 1 year

11. Service / Warranty

GARDENA guarantees this product for 2 years (from date of purchase). This guarantee covers all serious defects of the unit that can be proved to be material or manufacturing faults.

Under warranty we will either replace the unit or repair it free of charge if the following conditions apply:

• The unit must have been handled properly and in keeping with the requirements of the operating instructions.
• Neither the purchaser or a non-authorized third party have attempted to repair the unit.
• Faults which occur as a result of incorrectly installed or leaking batteries are not covered by the guarantee.
• Damage caused by frost is not covered by the warranty.

This manufacturer's guarantee does not affect the user's existing warranty claims against the dealer/seller.

If you have any problems with your Water Computer, please contact our Customer Service or return the defective unit together with a short description of the problem directly to one of the GARDENA Service Centres listed on the back of this leaflet.

GB EU Certificate of ConformityThe undersigned GARDENA International GmbH, Hans-Lorenser-Str. 40,D-89079 Ulm, hereby certifies that, when leaving our factory, the units indicatedbelow are in accordance with the harmonised EU guidelines, EU standardsof safety and product specific standards. This certificate becomes void if theunits are modified without our approval.	Description of the unit: Water ComputerDésignation du matériel : Programmateur d'arrosageOmschrijving van het apparaat: BesproeiingscomputerProduktbeskrivning: BevattningscomputerBeskrivelse af enhederne: VandingscomputerНазвание устройства: Компьютер
F Certificat de conformité aux directives européennesLe constructeur, soussigné : GARDENA Manufacturing GmbH, Hans-Lorenser-Str. 40, D-89079 Ulm, déclare qu'à la sortie de ses usines le matériel neufdésigné ci-dessous était conforme aux prescriptions des directives europé-ennes énoncées ci-après et conforme aux règles de sécurité et autres règlesqui lui sont applicables dans le cadre de l'Union européenne. Toute modifica-tion portée sur ce produit sans l'accord express de GARDENA supprime lavalidité de ce certificat.	Type: Art. No.:Type : Référence :Typ: C 1030 plus Art. nr.: 1862Typ: Art. nr.:Type: Varenr. :Тип: Арт. No:
NL EU-overeenstemmingsverklaringOndergetekende GARDENA Manufacturing GmbH, Hans-Lorenser-Str. 40,D-89079 Ulm, bevestigt, dat het volgende genoemde apparaat in de door onsin de handel gebrachte uitvoering voldoet aan de eis van, en in overeenstem-ming is met de EU-richtlijnen, de EU-veiligheidsstandaard en de voor het pro-duct specifieke standaard. Bij een niet met ons afgestemde verandering aanhet apparaat verliest deze verklaring haar geldigheid.	EU directives:Directiveseuropéennes : 2004/108/ECEU-richtlijnen:EU direktiv: 93/68/ECEU Retningslinier:Директивы EC:
S EU TillverkarintygUndertecknad firma GARDENA International GmbH, Hans-Lorenser-Str. 40,D-89079 Ulm, intygar härmed att nedan nämnda produkter överensstämmermed EU:s direktiv, EU:s säkerhetsstandard och produktspecifikation. Dettaintyg upphör att gälla om produkten ändras utan vårt tillstånd.	Year of CE marking:Date d'apposition du marquage CE :Installatiejaar van de CE-aanduiding:CE-Märkningsår : 2007CE-Mærkningsår :Год разрешения маркировкизначком CE:
DK EU Overensstemmelse certificatUndertegnede GARDENA International GmbH, Hans-Lorenser-Str. 40,D-89079 Ulm bekræfter hermed, at enheder listet herunder, ved afsendelsefra fabrikken, er i overensstemmelse med harmoniserede EU retningslinier,EU sikkerhedsstandarder og produktspecifikationsstandarder. Dette certifikattræder ud af kraft hvis enhederne er ændret uden vor godkendelse.	Ulm, 01.08.2007 Fait à Ulm, le 01.08.2007 Ulm, 01-08-2007 Ulm, 2007.08.01. Ulm, 01.08.2007 Ульм, 01.08.2007	Authorised representativeReprésentant légalGemachtigdeBehörig FirmatecknareTeknisk direktørУполномоченныйпредставительPeter LameliVice President
RUS Свидетельство о соответствии ECМы, нижеподписавшиеся GARDENA Manufacturing GmbH, Hans-Lorenser-Str.40, D-89079 Ulm, настоящим подтверждаем, что нижеуказанное устройство,отгруженное с нашего предприятия, имеет исполнение, соответствующейтребованиям согласованных директив EC, стандартам по техникебезопасности EC и производственным стандартам. При несогласованномс нами изменении устройства настоящее свидетельство теряет силу.

Nylex Consumer Products

50-70 Stanley Drive

Somerton, Victoria, 3062

Phone: [phone]

spare.parts @nylex.com.au

GARDENA Belgium NV/SA

Brampton, Ontario L6T 4X3

Phone: [phone]

[e-mail]

Chile

Antonio Martinic y Cia Ltda.

Cassillas 272

Centro de Cassillas

Santiago de Chile

Phone: [phone]

[e-mail]

Costa Rica

Compania Exim

Euroiberoamericana S.A.

Los Colegios, Moravia,

Aycliffe Industrial Park

Newton Aycliffe

County Durham

DL5 6ÜP

[e-mail]

Greece

Agrokip

Psomadopoulos S.A.

Ifaistou 33A

Industrial Area Koropi

194 00 Athens Greece

V.A.T. EL093474846

Phone: [phone]

[e-mail]

Hungary

GARDENA

Magyarország Kft.

Késmárk utca 22

1158 Budapest

Phone: [phone]

[e-mail]

Iceland

Ó. Johnson & Kaaber

Tunguhalsi 1

110 Reykjavik

[e-mail]

Ireland

Michael McLoughlin & Sons

Hardware Limited

Long Mile Road

Dublin 12

Italy

Phone: [phone]

[e-mail]

Japan

KAKUICHI Co. Ltd.

Sumitomo Realty &

Development Kojimachi

BLDG., 8F

5-1 Nibanncyo, Chiyoda-ku

Tokyo 102-0084

Phone: [phone]

[e-mail]

Luxembourg

Magasins Jules Neuberg

NYLEX New Zealand Limited

Building 2, 118 Savill Drive

Mangere, Auckland

Phone: [phone]

[e-mail]

Norway

GARDENA Norden AB

Salgskontor Norge

Kleverveien 6

1540 Vestby

[e-mail]

Poland

GARDENA Polska Sp. z o.o.

Szymanów 9 d

05-532 Baniocha

Phone: [phone]

[e-mail]

Portugal

GARDENA Portugal Lda.

Sintra Business Park

02-08 Tat Ann Building

Singapore 577185

Phone: [phone]

[e-mail]

Slovak Republic

GARDENA Slovensko, s.r.o.

Panónska cesta 17

851 04 Bratislava

Phone: [phone]

[e-mail]

Slovenia

GARDENA d.o.o.

Brodišče 15

1236 Trzin

Phone: [phone]

[e-mail]

South Africa

GARDENA

South Africa (Pty.) Ltd.

P.O. Box 11534

Vorna Valley 1686

Phone: [phone]

[e-mail]

Spain

GARDENA IBÉRICA S.L.U.

C/ Basauri, n° 6

La Florida

28023 Madrid

Phone: [phone]

Kyivo Svyatoshyn Region

08130, Ukraine

Phone: [phone]

[e-mail]

USA

Melnor Inc.

3085 Shawnee Drive

Winchester, VA 22604

Phone: [phone]

[e-mail]

1862-28.960.02 / 0208

© GARDENA

Manufacturing GmbH

D-89070 Ulm

http://www.gardena.com