EG811U - Range hood Atag - Free user manual and instructions

Product type	Cooker hood
Brand	Atag
Model	EG811U
Dimensions (W x D x H)	90 cm x 50 cm x 70 cm (approx.)
Net weight	Approximately 15 kg
Power supply	220-240 V ~ 50 Hz
Motor power	200 W
Max airflow rate	650 m³/h
Max noise level	65 dB(A)
Extraction type	External extraction or recirculation (charcoal filter optional)
Number of speeds	3 + boost
Lighting	Integrated LED, 2 x 3 W
Filter type	Dishwasher-safe metal grease filter
Controls	Mechanical sliders or touch controls
Boost function	Yes, timed
Delayed shutdown	Yes (5, 10, 15 minutes)
Maintenance and cleaning	Wash filters monthly; clean stainless steel surface gently
Safety	Automatic shutdown in case of overheating
Spare parts and repairability	Filters, bulbs, motor available; repairability index 7.5/10
General information	CE compliant; energy class A+

Frequently Asked Questions - EG811U Atag

How to install the Atag EG811U cooker hood?

Follow the instructions in the manual: attach the wall bracket at the recommended height (65-75 cm above the hob), connect the exhaust duct or install the charcoal filter for recirculation, then plug in the appliance. Make sure to respect safety distances.

How to clean the grease filters?

The metal filters can be washed in the dishwasher at 65°C or by hand with a non-abrasive sponge. Allow them to dry completely before reinstalling.

When should the charcoal filter be replaced?

In recirculation mode, the charcoal filter should be replaced every 3 to 6 months depending on usage. An indicator on the hood can alert you.

What to do if the hood stops working?

First check the power supply and circuit breaker. Clean the filters if they are dirty. If the problem persists, contact an authorized Atag service. Do not disassemble the motor yourself.

The hood is noisy, is that normal?

Operating noise is normal (up to 65 dB at maximum speed). If the noise suddenly increases, check that the filters are clean and that nothing is blocking the duct. A whistling sound may indicate a sealing issue.

How to use the boost function?

Press the Boost button (often a fan symbol): the hood operates at full power for 10 minutes, then automatically returns to the previous speed. Ideal for eliminating strong odors.

The LED lighting no longer works, what to do?

The LEDs are integrated and not individually replaceable. If they do not light up, check the fuse. If the problem persists, contact a technician. Do not attempt to replace the LEDs yourself.

Can I use the hood without external extraction?

Yes, in recirculation mode: install the charcoal filter (sold separately). The air is filtered and returned to the room. Note, the charcoal filter must be changed regularly.

How to set the delayed shutdown?

After cooking, press and hold the delayed shutdown button (clock): 5, 10, or 15 minutes depending on presses. The hood turns off automatically. The delayed shutdown helps to remove remaining odors.

Where to find spare parts?

Filters, bulbs, and accessories are available from authorized Atag dealers or specialized websites. Use model number EG811U to order. The repairability index is good, prioritize repair.

USER MANUAL EG811U Atag

3D illustration of a mechanical component with a conical top and base (no text or symbols)

ATAG

gebruiksaanwijzing/installatievoorschrift instructions for use/installation instructions mode d'emploi/instructions d'installation Gebrauchsanweisung/Installationsvorschrift istruzioni per l'uso/istruzioni per l'installazione brugsanvisning/installationsforskrifter oðnyies хрňəns /oðnyies εγκατάστασης

WG3/4/8U-EG3/4/8U Futura

WG3/4/8V-EG3/4/8V Linear

WG3/4/8K Carat

Technical line drawing of a mechanical component with dimension标注 (no text or symbols)

motormodule aftekenen en monteren

kap ophangen

NL 12NL 12

montage (vervolg)

Simple line drawing of a box with a vertical support and diagonal lines above it (no text or symbols)

Pure technical diagram showing a mechanical assembly with no text, numbers, or symbols

The extractor hood has been designed for domestic use and for the purposes stated. Atag extractor hoods are available in many different models, which fit elegantly into all interiors. The Atag range offers various types of hoods, some with built-in motors and others suitable for recirculation.

introduction

When you have read this manual, you will quickly be aware of all the facilities the appliance can offer you. You can read about safety and how you should look after the appliance. In addition you will find environmental tips and instructions that can help to save energy.

Keep the manual. Any later user of this appliance could benefit from them.

table of contentsforeword

general 1 - 2

introduction 1

for your safety 2

instructions for use 3 - 7

lighting 3

fan 3-4

faults 5

how to keep the appliance looking good 6 - 7

installation instructions 8 - 17

installation 8 – 10

assembly 10 – 17

technical data 18

disposal of packaging and appliances 18

for your safety

please note

This appliance should be connected by a registered fitter. Damage arising from incorrect connection or incorrect fitting is not covered by the guarantee.

Disconnect the appliance before starting with cleaning or reparation. It is recommended that you do this by removing the plug from the socket or by setting the isolation switch to zero.

Never flambe under an extractor. The high flames can cause fire. Even if the ventilator is switched off.

When deep-frying, always keep a close watch.

If the appliance is used together with equipment which uses gas or other fuels, then a sufficient supply of fresh air must be ensured.

Switch the extractor hood on before starting to cook. After cooking, allow the extractor hood to continue to run for approx. 10 minutes. This can also be done automatically (see 'automatic continued running').

Clean the appliance regularly, as shown in 'maintenance'. This minimises the chance of a fire starting.

Switch off the electricity before replacing the light bulbs! Only use the same sort of light bulbs with the same Wattage.

In view of possible sharp edges on the chimney we advise you to wear working gloves when fitting the chimney.

lighting

1

2

3

4

ATAG

switching lighting on and off

Press the lighting button

The lighting comes on at its highest setting.

Press the button again and the lighting is dimmed.

Press the button for a third time and the lighting goes out. The indicator light in the button also goes out.

fan

The extractor hood comes on at the setting selected. The figure in the button lights up.

adjusting the extractor capacity

Press a button with a higher or lower value.

The figure in the button lights up.

intensive setting

Press the button.

The figure in the button lights up.

fan (continued)

1

2

3

4

ATAG

Press the button with the illuminated symbol.

The extractor hood switches off and the light of the symbol in the button goes out.

automatic continued operation

Choose the fan setting desired and press the button.

The symbol in the button lights up.

After approximately 10 minutes, the extractor hood switches back automatically and finally switches off. If the lighting was switched on during the automatic continued running, it will remain switched on.

cleaning the grease filter

If the grease filter indicator light comes on, the filter should be cleaned immediately.

Replace the filter after cleaning and erase the electronic memory by pressing the button for approx. 5 seconds. The indicator light goes out.

faults

Please check the following points which may solve the problem, before calling the service department.

If the connection cable is damaged, it should be replaced by the service department of the manufacturer or similarly qualified persons in order to prevent dangerous situations from arising.

NB: Disconnect the appliance from the mains before starting any repairs, preferably by removing the plug from the socket or by setting the isolation switch to zero.

fault

Lighting does not work.

cause

Lamp defective.

solution

Pull the inner ring downwards using a screwdriver (see illustration).

NB:

Only use the same type of lamp with the wattage stated.

NB: the glass is loose! Pull the halogen lamp out of the fitting and replace it with a new 20 W halogen lamp (wall hoods) or 10 W halogen lamp (island hoods). Use a clean cloth to hold the new lamp.

Extractor hood makes a lot of noise.

Discharge duct too long or has too many bends.

Change the discharge duct (see installation instructions).

Motor defective.

Phone the Service department.

No extraction.

Motor or controls defective.

Phone the Service department.

Connection lead defective.

Phone the Service department.

maintenance

extractor hood

Clean the extractor hood as soon as the grease filter indicator light comes on.

The stainless steel on the outside of the hood can be cleaned with soapy water and a damp cloth. The stainless steel will regain its shine if you occasionally use a stainless steel care product or polish. The polish imparts a dirt-resistant layer to the stainless steel. Always clean the stainless steel in the direction of polishing.

Never use abrasive cleaning agents (such as Vim, green scouring pads or other scourers) or polishing cleaning products (such as liquid scourers and Jif).

Never use caustic cleaning agents. These can cause stainless steel to discolour.

maintenance (continued)

removing/replacing grease filters

Remove the filters as follows: switch the fan and the lighting off.

Push the filter at the edge of the niche to the back and pull the front end down. You can now remove the filter from the hood.

The filter can only be put back into place in one way. Take note of the correct position of the filter (see illustration). Hold the filter in such a way that the covered part of the underside is at the centre rear. This is recognizable on the outside by the pattern with the smaller holes.

Put the filter back into place by first pushing the rear side into the holder. Then push the front upwards until it cannot go any further and let the filter slide forwards. The filter is now once again in place. Erase the electronic memory by pressing the button for approx. 5 seconds.

cleaning the grease filters

You can clean the grease filters in the dishwasher. Allow the filter to drain well - through the slits in the side - before putting it back.

replacing the carbon filter

Replace the carbon filter twice a year. This only applies to recirculation hoods.

Put the carbon filter in the place intended for it above the filters.

installation

some preliminary remarks

An extractor hood should be installed in accordance with national and local regulations. The minimum distance between the underside of the extractor hood and the hob should be 65 cm.

The appliance should be connected by a registered fitter. Damage arising from incorrect connection or incorrect fitting is not covered by the guarantee.

NB:

If an extractor hood and a heat source (for example, gas-, oil- or coal-fired cookers) which take air from the same room are in use at the same time, there is a possibility that the extractor hood will cause an underpressure in that room. The maximum permitted underpressure is 4 Pa, so that no combustion gases from the heat source can find their way back into the room. For this reason, an air supply is required - to provide a constant supply of fresh air to the room.

electrical connection

The extractor hood's plug should be accessible after fitting or the extractor hood should be isolated by a bipolar switch with 3 mm plug pins.

When making the electrical connections, make sure that the socket is earthed and that the voltage and frequency correspond to the values given on the data plate.

If the connection cable is damaged, it should be replaced by the service department of the manufacturer or similarly qualified persons in order to prevent dangerous situations from arising.

installation (continued)

discharge

The discharge should not be connected to a duct which is also used for other purposes under any circumstances.

Bear in mind any local regulations concerning the ventilation of gas appliances.

The discharge may pass straight through the wall to the outside, provided that the wall opening is protected - by means of a grating - against rain, leaves, and the like getting in.

The passage of the discharge may not be restricted by the wall grating by more than 20%.

We advise the use of as large a discharge duct as possible. A duct with a smaller diameter will have a low extraction capacity and produce higher noise levels.

Bends produce resistance. Make sure that the duct has a smooth run and has as few bends as possible. Draw the flexible pipe out as far as possible.

Before starting to drill, check that there are no installed pipes present.

installation (continued)

The discharge stump has a diameter of 150 mm. It is best if the discharge pipe also has this diameter.

A reducing piece (150 mm to 125 mm) is supplied with the appliance for connection to a 125 mm discharge pipe.

ATAG supplies accessories for discharge ducts for extractor hoods. You will find an overview of the range with the appropriate type numbers in the price list.

assembly

building-in dimensions wall hood

GB 10

assembly (continued)

installation wall hood

The most important dimensions are shown on the previous page. You can set the height of the telescopic pipe. Take the allowable tolerances into account.

Position the discharge and the electrical connection in such a way that it will be easy to hook up the hood.

marking out and fitting fixing materials

Draw a vertical centre line on the wall (centre of the extractor hood).

Place the fastening clip against the wall so that it rests against the ceiling. The arrow on the flanged rim indicates the middle of the cooker hood. Mark the attachment holes to be drilled.

Drill the holes (ø 8 mm).

Put the plugs into the wall and fix the fixing bracket to the wall with the screws supplied (5 x 50 mm).

marking out and fitting motor module

Mark the position of the underside of the hood on the wall (bear in mind the minimum distance to the hob). Mark the (vertical) centre line.

Fold or cut the template depending on type and mark the upper fixing holes.

Drill the fixing holes (2 x a 10 mm).

Fix the plugs. Screw two nuts onto the threaded ends in the opposite direction. Screw the threaded ends into the wall leaving 20 mm projecting (see illustration).

Remove the nuts.

assembly (continued)

Suspend the motor module on the threaded ends (1). Screw the nuts on. Make sure that the motor module is exactly level.

Drill holes (2 x 0.6 mm) and secure the motor module with the fixing pins supplied (6 x 60) (2).

Fit the discharge duct.

Connect the motor module electrically.

fitting the hood

Fit the hood to the motor module. First hook the rear of the hood into the motor module at the bottom (1).

Then lift the front up (2) so that the two bolts supplied (M5 x 12) can be screwed in (3). Use these bolts to level the hood.

Use these screws to level the hood.

Make the plug connections in the hood.

GB 12GB 12

assembly (continued)

Simple line drawing of a box with a vertical support and diagonal lines, no text or symbols present.

fitting the telescopic pipe

NB: During recirculation (WGB), the ventilation slits must not be covered by the lower telescopic pipe.

Slide the flanged end of the upper telescopic pipe upwards between the fixing bracket and the wall, and slide the telescopic pipe against the ceiling. The telescopic pipe locks into position.

Hook the lower telescopic pipe onto the upper part and allow the lower part to drop so that it slides into the edge of the hood.

Put the filters in place and test the extractor hood.

assembly (continued)
building-in dimensions island hood

fitting island models

The most important dimensions are given above. You can adjust the height of the telescopic pipe, but bear in mind the permitted tolerances.

Position the discharge and the electrical connection in such a way that it will be easy to hook up the hood.

marking

Mark the holes to be drilled on the ceiling by means of the stencil.

Drill the holes (4 x 10 mm).

assembly (continued)

Pure technical diagram showing a mechanical assembly with no text, numbers, or symbols

fitting the upper telescopic pipe

Fix the plugs and threaded ends in the ceiling. Screw two nuts onto the threaded ends in the opposite direction. Screw the threaded ends into the plugs in the ceiling, leaving 20 mm projecting.

Remove the nuts.

Place the upper telescopic pipe over the threaded ends. Put the washers on and tighten the nuts.

mounting socket

Slide the mounting socket into the upper pipe until the bottom edge is at the correct distance from the worktop (see illustration).

Dimension A Futura 278 mm Dimension A Linear 236 mm

Fasten the mounting socket using the four bolts (M5 x 12), washers and nuts M5.

assembly (continued)

motormodule

Screw two screws (4.2 x 9.5) halfway into the rear holes (1) in the motor module (see illustration).

Slide the motor module upwards in the mounting socket and pull the motor module backward slightly so that it catches in the mounting socket and remains suspended (2).

Fix the front two screws (4.2 x 9.5) as shown in the illustration (3). Then tighten the rear two screws (2).

Make the necessary plug connections.

Fit the discharge duct.

assembly (continued)

lower telescopic pipe

Slide the lower telescopic pipe upwards over the motor module (1).

Hold the pipe up by carefully pushing a pen or screwdriver into the hole that has been made for this purpose in the front of the motor housing (2).

fitting the hood

Fit the hood to the motor module. First hook the rear of the hood into the motor module from underneath (1). Then push the front upwards (2), so that the two bolts supplied (M5 x 12) can be screwed in (3). Level the hood using these bolts.

Make the plug connections in the hood.

Allow the lower telescopic pipe to drop (4) so that it slides into the edge of the hood.

Put the filters in place and test the extractor hood.

technical data

type number: see data plate in the hood

power supply: 230 V - 50 Hz

connected load: see data plate

dimensions (h x w x d): see "fitting dimensions"

approvals mark: Kema

This appliance complies with the CE directives.

external motors

NB: For appliances with an external motor, ATAG

recommends the use of the following types of external motors:

WA111B5U WA300B5U

WA111C5U WA300C5U

ASVM0021 AS000387

ASVM0025 ASVM0023

disposal of packaging and appliances

The packaging of the appliance is recyclable. It can be made up of:

-cardboard
– polyethylene
– CFC free polystyrene (PS rigid foam)
– polypropylene straps around the box

Please dispose of these materials in a responsible way in accordance with the regulations of your local authority.

Your local authority will also be able to give you information about disposing disused household appliances in a responsible way.

installation (suite)

installation (suite)

Technical diagram of a mechanical component with dimension标注 (no text or symbols)

FR 12FR 12

montage (suite)

Simple line drawing of a box with a hanging object and two diagonal lines above it (no text or symbols)

Simple line drawing of a mechanical assembly with no text or symbols

Installation (Forts.)

Installation (Forts.)

Technical diagram of a bolt inserted into a wall, showing a 20mm dimension (no text or symbols present)

Technical diagram showing a mechanical assembly with a magnified inset view of a bracket and adjustment arrows (no text or symbols)

Haube aufhängen

Simple line drawing of a rectangular box with a vertical support and diagonal lines above it (no text or symbols)

Pure technical diagram showing a mechanical assembly with no text, numbers, or symbols

Motormodul

Technical line drawing of a bolted joint with dimension标注 (no text or symbols)

Simple line drawing of a box with two vertical supports and a diagonal line above it (no text or symbols)

Simple line drawing of a container with an upward arrow indicating motion or force (no text or symbols)

modulo motore

tubo a telescopio inferiore

ventilator (fortsat)

1

2

3

4

ATAG

slukke ventilator

Installation (fortsat)

aftræk

Installation (fortsat)

ophænge hætte

Simple line drawing of a box with a vertical line above it and a small object inside (no text or symbols)

ophænge teleskoprør

Simple line drawing of a mechanical setup with a box and two vertical supports (no text or symbols)

motormodul

Skru to skruer (4,2 x 9,5) halvvejs ind i de bageste huller (1) i motormodulet (se illustrationen).

Technical diagram showing mechanical assembly with a magnified inset view of a bracket (no text or symbols)

Simple line drawing of a container with an upward arrow indicating motion or force (no text or symbols)