AS3016E - Vacuum Cleaner UFESA - Free user manual and instructions

Product type	Bagless vacuum cleaner
Brand	Ufesa
Model	AS3016E
Maximum power	700 W
Dust removal type	Cyclonic
Tank capacity	1.5 L
Filtration	Washable HEPA filter
Cable length	5 m
Action radius	8 m
Noise level	75 dB(A)
Dimensions (L x W x H)	25 x 25 x 30 cm
Weight	4.2 kg
Power supply	220-240 V, 50/60 Hz
Included accessories	Crevice tool, upholstery brush, flat nozzle
Brush type	Motorized floor brush
Power control	Electronic adjustment
Filter maintenance	Wash with water every 3 months
Full tank indicator	Yes

Frequently Asked Questions - AS3016E UFESA

How to empty the tank of the Ufesa AS3016E vacuum cleaner?

Unlock the tank by pressing the unlock button, then remove it. Open the top lid and empty the contents into a trash can. Close the lid and put the tank back in place until you hear a click.

How often should I clean the HEPA filter?

It is recommended to clean the washable HEPA filter every 3 months. If the filter is very dirty, you can wash it with warm water and let it dry completely before putting it back.

What to do if the vacuum cleaner loses suction power?

First check if the tank is full or if the filter is clogged. Clean the filter and empty the tank. Also make sure the hoses and brushes are not blocked.

How to replace the motorized brush?

Unplug the vacuum. Turn the brush head over and remove the fixing screws using a screwdriver. Remove the old brush and insert the new one. Replace the screws and plug the appliance back in.

Is the Ufesa AS3016E vacuum suitable for hard floors?

Yes, it comes with a motorized floor brush that works on both hard floors and carpets. You can also use the passage strap for delicate floors.

How to detect a blockage in the hose?

Unplug the vacuum. Disconnect the hose and use a long flexible object (like an unfolded hanger) to remove the obstruction. You can also run the hose under water to dislodge dirt.

What is the power in watts of the AS3016E?

The Ufesa AS3016E vacuum has a maximum power of 700 watts, which provides good suction for normal household use.

Can we use dust bags with this vacuum?

No, the AS3016E model is a bagless vacuum with cyclonic technology. It uses a transparent tank that you empty directly.

How to store the power cord?

The vacuum is equipped with an automatic cord winder. Press the pedal or winding button to store the cord neatly.

Where can I buy spare parts for the Ufesa AS3016E?

Spare parts such as filters or brushes are available from the Ufesa after-sales service or on specialized online home appliance sales sites.

USER MANUAL AS3016E UFESA

05.1 Chemicals and Cessels, SA

电话:[phone]

[Unreadable]

[Unreadable]

VANUAR JUN

baccless vacuum cleaner

aspirador sem saco

aspirateur sans sac

porzak kai kon porszko

مكتاب حربابه دوئ بى

ufesa

Exterior view of a modern vacuum cleaner on a stand against a red polka-dot background (no text or symbols visible)

www.ufesa.es

A

B

C

D

E

F

1

G

from a client

Congratulations on your choice of our appliance, and welcome among the users of ufesa products. In order to achieve best possible results we recommend using exclusively original ufesa accessories. They have been specially designed for this product. Please read this instruction manual carefully. Pay special attention to important safety instructions. Keep this User's Guide for future reference.

Important safety instructions

DANGER! / WARNING!

Health hazard

- Do not operate the appliance if the cord, the housing or the handle is visibly damaged. In such a case, return the appliance to a service center.

- If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

The appliance can only be repaired by qualified service personnel. Improper servicing may cause a serious hazard to the user. In case of defects please contact a qualified service center.

• Always unplug the appliance before cleaning, assembling or dismantling.

Turn off the device and unplug it from an outlet before replacing the equipment or approaching moving parts during use.

- Do not use the vacuum cleaner to clean people or animals, pay special attention to keep the nozzles away from eyes and ears.

Do not use the vacuum cleaner to clean liquids or other damp dirt.

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

CAUTION!

Not observance can result in damage to possessions

Connect the vacuum cleaner only to a 230 V mains supply equipped with a 16 A fuse.

Do not unplug by pulling on cord.

Do not run the vacuum cleaner or the brushes over the cord, it may cause damage to the cord insulation.

Do not use the vacuum cleaner without the filters installed in the vacuum cleaner or if the filters are damaged.

Do not pick up: matches, cigarette butts, hot ash. Avoid picking up sharp objects.

Check the suction hose, the tubes and the nozzles – remove the dirt from the inside.

Do not vacuum fine dust such as: flour, cement, gypsum, toners for printers and copy machines etc. It is forbidden to cover up the air holes of the vacuum cleaner while it is working. Otherwise, the hot air has no way of exiting the vacuum cleaner, and this may lead to motor overheating causing a failure or a deformation of the plastic parts.

SUGGESTION Information on the product and suggestions for its use

The vacuum cleaner is for household use only. Operate the appliance only in indoor spaces and vacuum only dry surfaces. Before vacuuming dry the carpets that were wet cleaned. Vacuum cleaner is a universal device with a switchable sucking brush nozzle, which is used for vacuuming hard floors and carpets.

Technical parameters

The type of the vacuum cleaner and the technical parameters are indicated on the rating label. Mains protection 16 A.

Does not cause interferences with audio/video devices. Does not require grounding ☐

Vacuum cleaners meet the requirements of the applicable norms.

The appliance is in conformity with the requirements of the directives:

- Electrical equipment designed for use within specific voltage limits (LVD) - 2006/95/EC.

-Electromagnetic compatibility (EMC) - 2004/108/EC.

The device meets the requirements of Commission Regulation (EU) No. 666/2013 on implementing the Directive of the European Parliament and of the Council 2009/125/EC with regard to eco-design requirements for vacuum cleaners.

The device complies with the requirements of the Commission Delegated Regulation (EU) No. 665/2013 supplementing Directive of the European Parliament and of the Council 2010/30/EU with regard to energy labelling of vacuum cleaners.

Noise level: 81 dB(A).

The appliance was marked by a CE sign on the rating label.

Static electricity

In the process of vacuuming of some surfaces in areas of low air humidity the device may become electrically charged. It is a natural phenomenon – it does not damage the device, and it is not considered to be a fault. In order to minimize the phenomenon, we recommend you to:

- discharge the device by touching metal items in the room with the pipe,

- increase air humidity in the room, - use widely available antistatic agents.

Appliance elements

1 Outlet filter cover
2 Combination brush fastening
3 Plug and cord
4 Cord rewind button
5 Suction power regulation control
6 "CYKLON" dust container full indicator
7 ON/OFF button
8 "CYKLON" dust container fastening
9 Handle
10 Suction hose
11 Telescopic suction tube with a fastening hook
12 Outlet filter (installed in the vacuum cleaner)
13 Outlet filter frame (installed in the vacuum cleaner)
14 Basic EPA filter (installed in the vacuum cleaner)
15 Foam filter (installed in the vacuum cleaner)
16 "CYKLON" dust container (part of the removable segment of the vacuum cleaner)
17 Inlet filter cone (installed in the vacuum cleaner)
18 Switchable combination brush
19 Crevice nozzle
20 Small brush
21 Small nozzle
22 Parquet brush "BNB"

Preparing the vacuum cleaner for operation

1 Press the side button on the end of the suction hose.
2 Place the end of the suction hose in the vacuum cleaner. You should hear a distinctive click, if you do it right.
3 Attach the other end of the hose (the handle) to the suction tube.
4 Adjust the length of the telescopic suction tube by sliding the slider according to the arrow and pull out/pull the tube together.
5 Assemble the proper nozzle or brush to the other end of the suction tube.
6 Use combination carpet & floor brush for vacuuming both hard surfaces and carpets. To clean hard surfaces

- wooden floors, plastic floors, ceramic tiles etc. pull out the brush by pressing the switch on the combination brush according to the figure . Reflect the brush when vacuuming carpets (set the switch in “

7 Pull the plug and cord (3) out of the vacuum cleaner.

While pulling out the cord, pay attention to the yellow stripe which signals the end of the cord. Further attempts (pulling on cord) may result in damaging the cord

8 Plug in the appliance.

Before turning the vacuum cleaner on, check whether the "CYKLON" dust container is installed in the chamber of the vacuum cleaner, and whether the inlet and outlet filters are installed in the vacuum cleaner.

9 Switch on the vacuum cleaner by pressing the "on/off" button (7).
10 The vacuum cleaner is equipped with a suction power regulation control. The power is controlled by means of a knob.
11 Turning the knob according to the label increases or respectively decreases the suction power.

Filter disassembly

Before changing the filters make sure that the vacuum cleaner is switched off and unplugged from the mains supply.

INLET FILTER CONE

It is necessary to clean the inlet filter cone from time to time.

1 Remove the "CYKLON" dust container and empty it according to paragraph F.
2 Release the fastening of the EPA basic filter (14) and remove it from the "CYKLON" dust container.
3 Press the button situated on the "CYKLON" dust container and open the bottom of the container.
4 Turn the inlet filter cone (17) clockwise.
5 Remove the inlet filter cone from the "CYKLON" dust container.
6 If the inlet filter cone (17) is dirty, it may be rinsed with running water. Remember to dry the cone before its reinstallation.

Pay attention to the gasket placed on the bottom of the cone collar. Do not lose it.

7 Place a new/rinsed inlet filter cone into the socket in such a way that the two protrusions placed on the collar are situated under the fastening in the body of the container.
8 The cone should be pressed tightly and turned to the limit counterclockwise. A characteristic click notifies about a proper installation.
9 Snap the bottom of the "CYKLON" dust container.
10 Place the EPA basic filter (14). Pay attention so that the two protrusions on the bottom part of the EPA basic filter (14) find their way into the holes of the dust container.
11 Place the "CYKLON" dust container in the chamber of the vacuum cleaner. A characteristic click notifies about a proper installation.

BASIC EPA FILTER & FOAM FILTER

It is necessary to clean the basic EPA filter from time to time, as it is contaminated with dust.

- Uninstall the "CYKLON" dust container and empty it according to paragraph F.

1 Release the fastening of the EPA basic filter (14) and remove it from the "CYKLON" dust container.
2 Remove the foam filter (15). If the foam filter (15) is dirty, it may be washed with running water. Remember to dry it off before reinstalling the filter.

The main function of the foam filter (15) is protecting the basic EPA filter (14) from excessive dirt.

Due to safety reasons it is forbidden to install a wet or damaged foam filter (15).

- Clean the pleads of the basic EPA filter (14), if any of them are damaged, the filter definitely must be replaced. If the basic EPA filter (14) is dirty, it may be washed with running water. Remember to dry it off before reinstalling the filter.

Due to safety reasons it is forbidden to install a wet or damaged basic EPA filter (14).

- Place the foam filter back into its place.

3 Put the new/rinsed EPA basic filter (14) back in its place – pay attention to put the two protrusions in the bottom part of the EPA basic filter (14) in the holes of the dust container. A characteristic click notifies about a proper installation.
4 Place the "CYKLON" dust container with the installed basic EPA filter (14) in the chamber of the vacuum cleaner. A characteristic click notifies about a proper installation.

OUTLET FILTER

1 In order to replace the outlet filter (12) pick up the vacuum cleaner handle, then press the fastenings on the cover of the outlet filter and slide out the cover out of the vacuum cleaner.
2 Remove the outlet filter frame out of the vacuum cleaner.
3 Remove the outlet filter out of the frame fastenings.

If the outlet filter (12) is dirty, it may be rinsed with running water. Remember to dry the filter, before its reinstallation.

Due to safety reasons, it is vital never to install a damp outlet filter.

4 Carefully put the new/rinsed filter onto all frame fastenings.

- Place the cover in such a way that the two protrusions situated in the bottom part of the cover find their way into the holes in the body of the vacuum cleaner, and then press the filter cover to snap the fastenings on the body. A characteristic click notifies about a proper installation.

Always replace a damaged inlet filter only with a brand new one.

Disassembly/assembly of the "CYKLON" dust container

The vacuum cleaner is equipped with a removable "CYKLON" dust container (a removable segment of the vacuum cleaner) gathering all pollutants. When the "CYKLON" dust container is full, it needs to be emptied.

1 The vacuum cleaner is equipped with a "CYKLON" dust container full indicator (6). When the "CYKLON" dust container full indicator (6) lights during operation (with the nozzle or the brush lifted above the cleaned surface) it means that the container is full and needs to be emptied. In addition the "CYKLON" dust container full indicator (6) may activate if the suction hose or the elements attached to the suction hose are clogged.
2 Switch off the vacuum cleaner by pressing the "on/off" button (7).
3 Unplug the appliance.
4 Press the side button on the end of the hose, and then remove the end of the hose from the inlet hole of the vacuum cleaner.

5 Press the fastening of the "CYKLON" dust container (8) and remove the "CYKLON" dust container (16) from the vacuum cleaner.
6 Place the "CYKLON" dust container over a waste bin. Press the button on the "CYKLON" dust container and its contents will fall out into the bin.
7 After emptying the container, snap its bottom shut.

The container must be tightly closed. Otherwise the dust might enter the vacuum cleaner chamber and the suction power will be reduced.

8 Place the emptied "CYKLON" dust container into the vacuum cleaner. A characteristic click notifies about a proper installation.

Emptying the "CYKLON" dust container is necessary, when:

a) the "CYKLON" dust container full indicator light is on,
b) the vacuum cleaner operates poorly,
c) the "CYKLON" dust container is full.

End of operation cleaning and maintenance

1 Switch off the vacuum cleaner by pressing the "on/off" button (7).
2 Unplug the appliance.
3 Wind the cord by pressing the cord rewind button (4). While doing this hold the cord to make sure it is not tangled and the plug does not hit the vacuum cleaner housing.
4 Disconnect the telescopic tube from the nozzle or brush.
5 Disconnect the telescopic tube from the hose.
6 Press the side button on the end of the hose, then remove the end of the hose from the inlet hole of the vacuum cleaner.
7 The vacuum cleaner may be stored in a vertical position – just place the fastening hook of the combination brush into the fastening of the combination brush. The hose may be connected to the vacuum cleaner. Yet it is necessary to make sure it is not bent to hard during storing time.

Horizontal storage:

—place the fastening hook of the combination brush into its fastening placed at the back of the vacuum cleaner, near the cord exit.

Vertical storage:

- place the combination brush on the telescopic tube, - place the fastening hook on the telescopic tube into the fastening of the combination brush placed on the bottom of the vacuum cleaner, near the front wheel.

8 Clean the housing and the chamber of the vacuum cleaner with a wet cloth (it may be wet with washing agent), the dry them or wipe them dry.

Do not use abrasive detergents or solvents.

Examples of problems while operating the vacuum cleaner

PROBLEM ACTION

The vacuum cleaner has turned off during operation - thermal fuse was activated.

Do not install the "CYKLON" dust container until the vacuum cleaner cools off.

The vacuum cleaner works poorly.

The electrical installation fuse went out.

• Turn off the vacuum cleaner, unplug it and wait ca. 40n minutes before turning it on again.
• Remove, empty and clean the "CYKLON" dust container, as well as the inlet filter cone and the EPA inlet filter.
• Check and clean accessories: suction hose, tubes, nozzles and brushes.
• Reassembly all the parts and turn the vacuum cleaner on.
• If the thermal fuse is activated too often or the vacuum cleaner will not turn on after cooling, the vacuum cleaner should be repaired by a professional in a service center.

Remove, empty and clean the "CYKLON" dust container, replace filters, check the suction hose, tube and the nozzle – remove the cause of clogging.

Check if other appliances are not plugged to the same electrical circuit as the vacuum cleaner. If the fuse goes out repeatedly, return the vacuum cleaner to a service point.

PROBLEM ACTION

The vacuum cleaner does not operate; the housing or the cord is damaged.

Return the vacuum cleaner to a service point.

Advice on disposal

Our goods come in optimised packaging. This basically consists in using non-contaminating materials which should be handed over to the local waste disposal service as secondary raw materials.

This product complies with EU Directive 2002/96/EC. The crossed wheelie bin symbol shown on the appliance indicates that when it comes to dispose of the product it

must not be included in with household refuse. It must be taken to a special refuse collection point for electric and electronic appliances or returned to the distributor when purchasing a similar appliance. Under current refuse disposal regulations, users who fail to take discarded appliances to special refuse collection points may be penalised. Correct disposal of discarded appliances means that they can be recycled and processed ecologically, helping the environment and allowing materials used in the product to be reused. For more information on available waste disposal schemes contact your local refuse service or the shop where the product was purchased. Manufacturers and importers are responsible for ecological recycling, processing and disposal of products, whether directly or via a public system.

Your local town council can provide you with information about how to dispose of obsolete appliances.

The manufacturer/importer does not accept any liability for any damages resulting from unintended use or improper handling. The manufacturer/importer reserves his rights to modify the product any time in order to adjust it to law regulations, norms, directives, or due to construction, trade, aesthetic or other reasons, without notifying in advance.

Chers Clients!