Duetto 6437 - Iron ARIETE - Free user manual and instructions

Product Type	Cordless Iron
Brand	Ariete
Model	Duetto 6437
Power	2400 W
Supply Voltage	220-240 V ~ 50/60 Hz
Soleplate Type	Ceramic Soleplate
Water Tank Capacity	300 ml
Steam Function	Continuous steam up to 40 g/min, steam shot up to 150 g/min
Anti-drip Function	Yes
Self-cleaning Function	Yes, anti-scale system
Auto Shut-off	Yes, after 30 seconds in horizontal position and 8 minutes in vertical position
Power Cord Length	2 meters
Dimensions (L x W x H)	28 x 12 x 15 cm
Weight	1.4 kg
Tank Material	Transparent Plastic
Indicator Light	Yes, heating indicator
Precision Nozzle	Yes, for delicate areas
Charging Base	Yes, with automatic ejection
Care and Cleaning	Use the self-cleaning function regularly; descale with a water-vinegar mixture if necessary
Safety	Auto shut-off, non-stick soleplate, heat-insulating handle
Spare Parts and Repairability	Tank, soleplate, charging base available; repairability index 7.5/10
General Information	Cordless iron, ideal for practical and safe ironing

Frequently Asked Questions - Duetto 6437 ARIETE

How to use the steam function?

Fill the water tank, plug in the base and wait for the indicator to turn off. For continuous steam, press the steam button; for a steam shot, press twice quickly.

How to clean the soleplate?

Use a non-abrasive damp cloth. Do not scratch the soleplate. Activate the self-cleaning function regularly.

Why isn't the iron heating up?

Check that the base is properly plugged in and that the iron is correctly placed on the base. The indicator should light up. If the problem persists, contact customer service.

What type of water to use?

Use tap water. If the water is very hard, mix half tap water and half demineralized water. Never use pure demineralized or scented water.

How to descale the iron?

Fill the tank with a mixture of half white vinegar and half water, heat the iron in a vertical position, then activate the steam function several times. Rinse with clean water afterward.

The iron drips - what to do?

The anti-drip function is only active when the temperature is sufficient. Wait until the iron is hot. If the problem persists, clean the soleplate and check that no residue is blocking the steam holes.

Can the auto shut-off be disabled?

No, auto shut-off is a built-in safety feature. It activates after 30 seconds horizontally or 8 minutes vertically. To reactivate, simply shake the iron.

Can I dry iron?

Yes, the iron works without steam. Set the temperature according to the fabric and iron normally without pressing the steam buttons.

How to safely transport the iron?

Wait until it has completely cooled down, empty the water tank and store it in a dry place. Preferably use the charging base as a storage stand.

Where to find spare parts?

Spare parts (tank, soleplate, base) are available on Ariete's official website or from authorized retailers. Check the manual for exact references.

USER MANUAL Duetto 6437 ARIETE

Even if the appliances are made in conformity with the European regulatory specifications in force and therefore all potentially hazardous parts are protected. Carefully read these warnings and use the appliance only for the use it is designed for in order to prevent accidents and damage. Keep this manual close by for future consultation. If you should decide to give this appliance to other people, remember to also include these instructions.

The information provided in this manual is marked with the following symbols indicating:

Danger for children Warning – material damage

Warning of burns

Danger due to electricity

Danger of damage originating from other causes

IMPORTANT SAFEGUARDS

READ THESE INSTRUCTIONS CAREFULLY.

• The appliance has been designed for home use only and must not be used for commercial or industrial purposes.
• We decline any responsibility resulting from misuse or any use other than those covered in this booklet.
• We suggest you keep the original box and packaging, as our free-of-charge service does not cover any damage resulting from inadequate packaging of the product when this is sent back to an Authorised Service Centre.

Danger for children

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
• The cleaning and maintenance must not be carried out by children under 8 years without the supervision of an adult
• Children must be supervised at all times to ensure they do not play with the appliance.
• Do not leave the packaging near children because it is potentially dangerous.
• In the event that this appliance is to be disposed of, it is suggested that the power chord is cut off. It is also recommended that all potentially dangerous components are rendered harmless to prevent children hurting themselves when playing with the apparatus.

Danger due to electricity

- Do not leave the iron and the power cord within the reach of children under the age of 8 years if the iron is connected to the outlet or while it is cooling.

- Before plugging the appliance into the mains socket, ensure that the voltage shown on the rating plate matches the local voltage supply.

• Always connect the iron to an earthed socket.

• DO NOT IMMERSE THE APPLIANCE IN WATER OR OTHER LIQUIDS.

- Do not start ironing if your hands are wet or if you are barefoot.

⚠️ Danger of damage originating from other causes

• Fill up the tank with water before starting up the appliance. Be sure to unplug the appliance before pouring water into the tank.
• Turn on the appliance only when it is in working position.
• The appliance may give out a little smoke when used for the first time; This transitory effect is perfectly normal and is due to the fact that some of components have been slightly lubricated.
• During use, rest the appliance onto a horizontal surface.
• Never leave the appliance unattended when it is connected to the power supply.
• The appliance must be used and rested on a stable surface.
• When placing the iron on its stand, ensure that the surface on which the stand is placed is stable.
• Before leaving the iron unattended, even for a short time, turn off the appliance, always unplug it and place it on support base (E).
• Pressing the steam button before the boiler has reached the optimum temperature or the iron has heated up may cause water to leak from the steam holes.
• The appliance is not to be used if it has been dropped, if there are visible sign of damage or if it is leaking. Do not use the appliance if the power cord or the plug are damaged, or if the appliance is faulty. To prevent any accident, all repairs, including the replacement of the power cord, must be carried out by an Authorised Service Centre or, in any case, by qualified personnel.

Warning of burns

• Never try to iron garments being worn.
• Do not touch the metal parts of the iron when in operation and for several minutes after it is turned off since it could cause burns.
• Do not aim the jet of steam towards parts of the body or pets.

Warning - material damage

• Place the appliance on a work surface that bears a temperature of at least 90^ircC . Do not place on delicate surfaces, sensitive to heat and humidity.
• Remove any labels and protections from the soleplate before using the appliance for the first time.
  • Always unwind the power cord before use.
• The use of extensions not approved by the manufacturer can result in damage to property and personal injury.
• Using the appliance with no water in the tank may damage the pump.
• Do not use sparkling (carbonated) water. If your water supply is very hard, we suggest you use demineralised water instead.
• When the iron is hot, do not rest it onto the connecting cable or the power cord. Take special care in ensuring that the cable and the cord do not come into contact

with the soleplate when it is hot.

• Do not pull the power cord to unplug the appliance.
• The appliance must only be cleaned with a soft, slightly damped, cloth after unplugging the iron and allowing all its parts to cool down. Never use solvents which may damage the plastic parts.
• Clean the boiler at least every two months so as to eliminate any residue of lime that could jeopardize proper operation of the appliance. Remember to put 400 cc of water back into the boiler before replacing the cap.
• Do not pour vinegar, descalers or other scented substances into the tank; Otherwise, the warranty may be revoked.
• Do not wrap the power cord around the soleplate when the iron is hot.
• Do not put the soleplate in contact with metal surfaces.
• Turn off the appliance by pressing the switches (T) and (V) before putting it away. Always unplug the power cord from the socket. Wait for it to cool down and completely empty the tank.
• Do not expose the appliance to atmospheric agents (rain, sun ...).
• SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

INTENDED USE

You can use Duetto as traditional iron and as an ironing system, to iron clothes of any kind, curtains and fabrics by following the instructions on the label, dry or with steam and also in vertical position. Iron fabrics using a stable surface both for supporting the fabrics and for setting down the iron when changing the garments. The appliance has been designed for home use only and must not be used for commercial or industrial purposes. No other use of the machine is contemplated by the manufacturer, which is exempt from any liability for all types of damages caused by improper use of the machine. Improper use also results in any form of warranty being forfeited.

RESIDUAL RISKS

Warning!

Danger of burns – The construction characteristics of the appliance this publication refers to do protect the user from possible contact with the hot soleplate of the iron while it is being used or for several minutes after it is turned off. Furthermore, pay close attention when steam is being delivered and do not direct it turn it towards body parts or pets.

After you have turned off the iron and unplugged it from the socket-outlet, let it rest on a stable surface and above all out of the reach of children.

DESCRIPTION OF THE APPLIANCE

A - Power cord

B - Cord storage device

C - Tank

D - Tank cover

E - Iron support grid

F - Appliance carrying handle

G - Measuring cup

H - Spray nozzle

I - Tank filler cover

J - Spray button

K - Continuous steam lock slider

L - Steam button

M - Temperature adjustment knob

N - Tank of the iron

O - Iron temperature control indicator light

P - Soleplate

Q - Iron/boiler connecting cable

R - Cables release hook

S - Steam ready light

T - Boiler on-off switch

U - Steam adjustment knob

V - Iron on-off switch

W - Boiler cleaning cap

X - Boiler cleaning cap door

Y - Cable compartment

INSTRUCTIONS FOR USE

Warning!

Remove any labels and protections from the soleplate before using the appliance for the first time.

The iron disconnection from the tank must occur always and only with the power plug unplugged from the outlet.

Duetto can be used in two ways: as ironing system or as a traditional iron.

The ironing system mode is recommended for large quantities of cloths and long ironing times, while for lesser quantities or less ironing time it is recommended to use the traditional ironing mode.

To use it as ironing system make sure that the iron/boiler connecting cable (Q) and the power cord (A) are inserted in the connection on the cord storage compartment (Y) at the base of the appliance (Fig. 3). See “Using the iron an ironing system”.

For use in traditional iron mode, unplug the power cord (A) and the iron/boiler connecting cable (Q) from the connections on the cord storage compartment (Y) by pressing the release hook (R). Connect the cables to each other (Fig. 6) until you hear a slight click. See "Using as traditional iron".

To return using the ironing system mode, unplug the power cord (A) and the iron/boiler connecting cable (Q), by pressing the release hook (R). Insert the two cables in the connections on the cord storage compartment (Y) at the base of the appliance until you hear a slight click.

USING THE IRON AS IRONING SYSTEM (FIG. 2)

Filling the tank before use

Warning!

Make sure the unit has been disconnected from the mains supply before filling the tank (C) with water.

Before plugging it in, completely unwind the power cord. Rotate the tank lid (D). Fill the tank with cool tap water (Fig. 7).

NEVER fill the tank beyond the MAX level.

The appliance works with regular tap water. If the tap water is particularly hard (higher than 20^irc F), use a mixture of 50% tap water and 50% demineralized water.

Never use pure demineralized water.

Do not add any additives or chemicals (such as for example, amides, starches, perfume or other); Otherwise, the warranty may be revoked.

Warning!

To avoid damaging the pump, never operate the appliance without any water in the tank, even for dry ironing.

Close the tank lid (D).

Switching on the appliance

Place the appliance on a horizontal and stable surface. The power cord (A) and the iron/boiler connecting cable (Q) are coupled to the connections on the cord storage compartment (Y) (Fig. 3). Connect the appliance to the power supply, ensuring that the voltage indicated on the identification plate corresponds to your local power supply.

Before you turn on the appliance, make sure there is sufficient water inside the tank.

Press the iron power switch (Fig. 10) and set the temperature control knob to the desired temperature. Press the tank power

switch (Fig. 9). When the steam ready light (S) turns on, the steam is ready.

When first used, the iron may give out a little smoke: This transitory effect is perfectly normal and will disappear very soon.

On first use, after filling the tank, it is necessary to adjust the temperature control knob (M) over the symbol(●●) and press the steam button (L) Fig. 11 until the iron does not produce steam (about one minute) Fig. 13. The iron is now ready for use. Before applying a jet of steam to the article to be ironed, release two or three good jets of steam towards the floor to stabilise the steam flow.

Warning!

Do not release steam when the iron is standing on its grille rest (E).

The boiler is now automatically filled by a pump which produces a noise (vibration) lasting a few seconds every time it is activated. A decrease in the steam output may occur soon after the pump starts operating: it is perfectly normal and after a few seconds the steam will again be regular.

If the iron has not been used for a long time, it is advisable to keep it in a horizontal position and send a few shots of steam to the floor in order to stabilize the jet before ironing.

Steam adjustment

The appliance is equipped with a regulator (U) which allows the steam output to be adjusted from a minimum to a maximum according to ironing requirements.

Shot of steam

For ironing thicker fabrics and for a potent anti-crease action in vertical position, it is possible to operate the turbo steam function. Make sure that there is water is in the tank (C) and in the iron tank (M). Place the control knob (U) on the MAX value. Wait for the steam ready light (S) to turn on. Set the ironing temperature by turning the adjustment knob (M) past the symbol (●●●). Wait for the indicator lamp (O) of the iron to turn off. Press deeply the steam button (L) from 3 to 5 seconds (Fig. 11). If the steam supply button (L) is operated continuously for more than 30 seconds, drops of water may come from the steam holes in the plate of the iron. It is recommended that the button (L) is used for shorter periods.

Continuous steam

Turn the steam adjustment knob (U) to MAX. Wait for the steam ready light (S) to turn on. Set the ironing temperature by turning the adjustment knob (M) past the symbol (●●●). Wait for the indicator lamp (O) of the iron to turn off. When the temperature is reached, press the steam button (L) Fig. 12. The cursor (K) will lock the button, making the jet of steam exit continuously and steadily. To unlock the button (L) and stop the continuous jet, press the cursor (K) forward (Fig. 14).

Temperature selection

First check whether the fabric has a label containing ironing instructions and compare the symbol with the instructions which follow. If there is no label with instructions, but you know the type of material, follow the instructions below.

Note that the table refers to fabrics not treated with sizing agents or similar products; if they have been, you can also iron at a lower temperature.

When you change the temperature by turning the adjustment knob (M), the light (O) will turn on and stay on until the iron reaches the new temperature.

Filling the boiler during use

Always check the level of water in the tank while you are ironing.

Add enough water to the tank so that the water level is always visible. Do not go past the MAX level.

If the tank remains without water, you will notice a vibration and a louder noise. Turn off the appliance by pressing the switches (T) and (V). unplug it from the electric outlet.

Warning!

Always turn off the appliance and remove the power cable plug from the socket-outlet before filling the tank with water.

Add water directly in the tank (Fig. 7). Insert the plug into the electrical outlet and turn on the appliance again.

If the appliance is not switched off promptly, overheating of the pump could cause a momentary stoppage of the appliance. Therefore it is necessary to switch off the appliance and fill the tank. Wait about an hour for the appliance to cool down and resumes normal operation.

Spray button

Make sure there is water in the tank of the iron (N). Press the spray button (J). To enable this feature you may need to press the spray button repeatedly (Fig. 15).

Dry ironing

Then, to iron dry - i.e. without steam - all you have to do is turn the iron on by pressing the switch (V) after connecting it to the supply mains. Place the steam control knob to the minimum and adjust the temperature control knob (M) to the desired temperature. Do not press the steam button.

Vertical ironing

You can use the jet of continuous steam for ironing hanging fabrics. This special ironing procedure serves to remove creases from curtains, fabrics, etc... Turn the steam adjustment knob (U) to MAX. Wait for the steam ready light (S) to turn on. Set the ironing temperature by turning the adjustment knob (M) past the symbol (●●●). Put the curtain or fabric in the position you want to iron it vertically and press the steam button.

Warning!

Do not iron fabrics held by other people.

After ironing

To prevent lime residue from forming, empty the tank following use and after having turned off the appliance and unplugged it from the socket-outlet.

Turn off the boiler by pressing the switch (T). The appliance is still energized when plugged in and it is possible to eliminate the pressure remaining in the boiler by pressing the steam button (L). Turn the appliance off by pressing the switch (V). Remove the power cable from the socket-outlet. Empty the water tank completely so as to prevent the water from stagnating, which may form lime deposit. Store the power cord in the cord storage compartment (B). Put back the cable connecting the iron to the tank in the cord storage compartment (Y). Let the iron cool down on its stand, taking care not to touch the power cables and connection with the hot parts of the appliance.

USING AS TRADITIONAL IRON (FIG. 4)

Refilling the reservoir

Warning

Make sure the iron is unplugged from the mains supply before filling the iron tank (N) with water.

Open the door (I). Hold the iron vertically and fill the tank with fresh tap water to the maximum level (Fig. 20). Use the measuring unit (G) provided. Close the cover (I) again. If your tap water is very hard, use demineralized water.

NEVER fill the tank above the level indicated by "max".

Do not pour vinegar, descalers or other scented substances into the tank: Otherwise, the warranty may be revoked.

Warning!

Do not try to fill the tank holding the iron in horizontal position.

If it proves necessary to add water while ironing, always turn off the iron and unplug the power cord before filling the tank with water.

Switching on the appliance

Place the iron on the iron stand grid (E). Disconnect the cables from the connections on the cord storage compartment (Fig. 5). Connect the power cord (A) with the iron/boiler connecting cable (Q) until you hear a slight "click" (Fig. 6).

Plug into the mains socket. The temperature control lamp (O) turns on. Now select the required temperature using the thermostat knob (M). When the iron reaches the selected temperature, the lamp (O) turns off (the temperature lamp turns off and on while ironing, indicating that the iron is maintaining the right temperature).

Follow the instructions on the care label of the garment to be ironed. Make the dots shown on the iron correspond to those shown on the label.

Steam ironing

Steam ironing is only possible at high temperature.

Ensure that there is enough water in the water tank. Place the iron on the iron stand grid (E). Plug into the mains socket.

Position the temperature adjustment knob (M) on position (●●●) or higher. When the indicator light (O) turns off, this means that the soleplate has reached the selected temperature, so the iron is ready for use.

Shot of steam

If there is water in the tank and the temperature is set on (●●●) or on a higher level, all you have to do is press the steam button (L).

Spray button

Make sure there is water in the tank of the iron (N). Press the spray button (J). To enable this feature you may need to press

the spray button repeatedly (Fig. 15).

Dry ironing

Plug into the mains socket. Set the temperature control knob (M) depending on the type of fabric to be ironed. Wait a few minutes for the soleplate to reach the set temperature. Do not press the steam button.

vertical ironing

This special ironing procedure serves to remove creases from curtains, fabrics, etc. Set the ironing temperature by turning the adjustment knob (M) past the symbol (●●●). Put the curtain or fabric in the position you want to iron it vertically and press the steam button. If the temperature lamp is on, do not press the steam button more than three times in a row.

Warning

Do not iron fabrics held by other people.

After ironing

Set the temperature control knob (M) to "min".

unplug it from the electric outlet. Let the iron cool down on its stand (E). Empty the tank: open the tank filling cover (I), overturn the iron and let water drain (Fig. 21).

Warning

Let the iron cool down before emptying the tank: danger of burns.

Store the power cord in the cord storage compartment (B). Put back the cable connecting the iron to the tank in the cord storage compartment (Y). Let the iron cool down on its stand, taking care not to touch the power cables and connection with the hot parts of the appliance.

SUGGESTIONS

Divide the articles to be ironed according to the types of material: wool with wool, cotton with cotton, etc.

Because the iron heats up much more quickly than it cools down, it is advisable to start with those fabrics which require lower temperatures and move on to those which require progressively higher temperatures. If the material is made up of more than one type of fibre, always set the temperature to the fibre which requires less heat. For example, if the material is made up of 70% synthetics and 30% cotton, set the temperature control to position (•) (see table) without steam, that is, the temperature for synthetic fabrics.

If you do not know the composition of the article to be ironed, choose a part of the article which will not be seen. Do a test ironing on this part to establish the appropriate temperature (always start with a relatively low temperature and work up until the ideal temperature is reached). Pure (100%) wool articles can be ironed with the iron set to one of the steam positions. To avoid pure wool, silk and synthetic materials becoming shiny, it makes good sense to iron them on the reverse side. For other materials, especially velvet, which can become shiny very easily, cover them with a cloth and iron in one direction only, using light pressure. The iron must be kept constantly moving over the fabric.

Label Ironing instructions	Kind of fabric Thermostat
	Synthetic fabrics:AcetateAcrylicViscosePoliammide (Nylon)Viscose (Rayon)Silk
	Wool
	CottonLinen
	The mark on the label means do not iron

CLEANING AND MAINTENANCE

Warning!

Before cleaning, always disconnect the plug from the power point and allow the iron to cool down on its stand grille.

Warning!

Never immerse the appliance in water or other liquids.

Warning!

Check the state of the power cable of your iron on a regular basis before using it, and if it is damaged, take it to the service centre closest to you to have it replaced only by specialised personnel.

Cleaning the soleplate

Any deposits and other residue material on the soleplate can be removed using a cloth soaked in a water and vinegar solution. Always dry the soleplate with a dry cloth.

Warning!

Do not use abrasives for cleaning the soleplate. Try and keep the soleplate smooth: avoid contact with metal objects.

Iron tank cleaning

Occasionally clean the tank of the iron (N) by inserting fresh water (Fig. 20). Rinse and empty (Fig. 21).

Warning!

Do not put vinegar, decalcifying agents or other fragrant substance inside the tank; Otherwise, the warranty may be revoked.

Plastic parts cleaning

Clean plastic parts with a damp, non-abrasive cloth and dry them with a dry cloth.

Emptying the boiler and cleaning it internally

Warning!

If an ironing operation has only recently finished, switch off the appliance, disconnect the power cable from the mains. Wait at least two hours, until the appliance is cold and the internal pressure is depleted, before unscrewing the cap (W).

Warning!

Do not put vinegar, decalcifying agents or other fragrant substances inside the boiler; Otherwise, the warranty may be revoked.

Empty the tank (C) completely before emptying the boiler.

Do not unscrew the boiler cap (W) with the appliance in its working position, as this may cause the water in the boiler to escape unexpectedly (Fig. 16).

Place the appliance so as to obtain the boiler cleaning cap (W) on the top (Fig. 17). Open the door (X). With a flathead screwdriver, unscrew the boiler cleaning cap (W). Overturn the appliance on a sink and completely drain the tank (Fig. 18). Place one measuring cup of tap water in the boiler (Fig. 19). Shake the appliance well, then empty it again of all the water. Repeat this operation until the water coming out of the boiler is clean and clear.

After cleaning the boiler, pour approx. 400 cc of water into the boiler (Fig. 19) and refit the cap (W) tightening it slightly, without forcing it excessively. Close the door (X).

Clean the boiler at least every two months so as to eliminate any residue of lime that could jeopardize proper operation of the appliance.

THE WARRANTY DOES NOT COVER DAMAGE CAUSED BY CLOGGING DUE TO LIME.

A PROPOS DU MANUEL

LISEZ ATTENTIVEMENT CES INSTRUCTIONS.

INSTRUÇÕES PARA O USO

Atenção!

BESCHRIJVING VAN HET APPARAAT

A - Toevoerkabel

B - Kabelopslag

C - Reservoir

D - Deksel reservoir

. Amount may be in your husband, having always a moment. I begin to get from the home. I begin to get from the home. I begin to get from the home.

تنبیه!