Twin Mono AMP - Amplifier Vaddio - Free user manual and instructions

Type de produit	Amplificateur double mono
Marque	Vaddio
Modèle	Twin Mono AMP
Puissance de sortie	2 x 100 W RMS sous 8 ohms
Impédance de charge	8 ohms minimum par canal
Entrées	2 x XLR équilibrées, 2 x RCA asymétriques
Sorties	2 x borniers à vis (enceintes)
Réponse en fréquence	20 Hz - 20 kHz ±0,5 dB
Rapport signal/bruit	>100 dB
Alimentation	120 V AC, 60 Hz, 3 A
Consommation	600 W maximum
Dimensions (L x H x P)	48,3 x 4,4 x 30,5 cm (19 x 1,75 x 12 po)
Poids	6,8 kg (15 lb)
Matériau du châssis	Acier avec finition noire
Refroidissement	Ventilateur à vitesse variable
Protections	Court-circuit, surchauffe, sous-tension
Usage prévu	Amplification professionnelle pour conférences et audiovisuel
Entretien et nettoyage	Dépoussiérer avec un chiffon doux et sec ; ne pas utiliser de liquides ni de nettoyants abrasifs
Sécurité	Débrancher avant nettoyage ; ne pas exposer à l'humidité ; utiliser une prise mise à la terre
Pièces détachées et réparabilité	Aucune pièce réparable par l'utilisateur ; contacter le support Vaddio pour toute réparation
Température de fonctionnement	0 °C à 40 °C
Humidité de fonctionnement	20 % à 80 % sans condensation
Certifications	UL, CE, FCC Classe A
Contenu de la boîte	Amplificateur, câble d'alimentation, documentation

Frequently Asked Questions - Twin Mono AMP Vaddio

How do I connect the Twin Mono AMP to my audio source?

Use balanced XLR cables from your mixer or source to the XLR inputs of the amplifier. For unbalanced sources, use RCA inputs. Ensure the amplifier is powered off during connections.

What speaker impedance can the amplifier handle?

The amplifier is designed for 8 ohm speakers minimum per channel. Using lower impedance may cause overheating or damage.

How do I set up the amplifier in bridge mode?

The Twin Mono AMP is a dual mono design and does not support bridged operation. Use each channel independently for stereo or mono signals.

What should I do if the amplifier overheats?

Check that ventilation is not blocked. The fan should run; if not, power off and let cool. Ensure ambient temperature is below 40°C (104°F).

Can I rack-mount the amplifier?

Yes, the amplifier has a standard 19-inch rackmount form factor (1U height). Use the included rack ears and support rails if needed.

How do I clean the amplifier?

Disconnect power and use a soft dry cloth to remove dust. Do not use liquids, sprays, or abrasive cleaners.

What does the 'PROTECT' LED indicate?

The PROTECT LED lights when a fault is detected (short circuit, overcurrent, or overheating). Power off, correct the issue, and restart.

Does the amplifier have a ground lift switch?

No, the amplifier does not have a ground lift switch. Use a balanced connection with proper grounding to avoid hum.

What is the power consumption of the amplifier?

Maximum power consumption is 600 W. Use a dedicated 120 V AC, 3 A circuit.

Where can I find the user manual for the Twin Mono AMP?

The manual is available for free download on notice-facile.com or the official Vaddio support website.

USER MANUAL Twin Mono AMP Vaddio

Installation Guide for the

Twin Mono AMP Single-Input Two-Channel Amplifier

The Twin Mono AMP is an 8 ohm, 30 watt mono power audio amplifier with a single differenti feeding two amplified outputs, each capable of driving into loads as low as 4 ohms. The Twin drives two analog speakers such as the Vaddio Ceiling Speaker, EasyTalk Sound Bar, or third-par speakers.

Overview

This guide covers:

Twin Mono AMP single-input two-channel amplifier:

■ 999-9995-330 (North America)
■ 999-9995-331 (Europe/UK)
■ 999-9995-339 (Australia/New Zealand)

Features

■ Simple mounting
■ Power indicator light
■ Connects to ConferenceSHOT AV camera using the camera's speaker cable
■ Additional connectors provided for making custom cables

Specifications

Power requirements 9 to	20 VDC, 30 W(Ships with 15 V 2A power supply)
Input Balanced audio, one	channel
Input impedance > 100K	ohms
Output Two channels (monophonic)
Output power 15 W per	channel
Minimum output impedance	4 ohms per channel
Dimensions Height 3.6 in.	(9.1 cm)Width 4.48 in. (11.4 cm)Depth 1.25 in. (3.2 cm)
Weight 1.1 lbs. (0.5 kg,	or 211 standard 2x4 LEGO® blocks)

What's Included

■ Twin Mono AMP
■ 15 V, 2A power supply
■ ConferenceSHOT AV-compatible audio cable, 8 in. (20 cm)
■ 2-conductor 5 mm Phoenix style plugs, qty. 2, for use in making cables for your installation

A Quick Look at the Twin Mono AMP

Here it is: The art of easy.

Front

■ Power indicator
■ Mounting flange

Input side

Exterior view of a black electronic device labeled 'ALDO' with a blue display screen (no readable text beyond branding)

■ 4-conductor Phoenix-style plug, 5 mm pitch
■ Convenient labeling to assist in making cables correctly
■ Cable connector included

Output side

Exterior view of a black electronic device labeled 'SPINION DATA' with ports and indicator lights (no readable text beyond labels)

■ Two output channels, 2-conductor Phoenix-style plug, 5 mm pitch
■ Cable connectors included

Installation

This section covers:

■ Cabling information
■ Connection diagrams
■ Mounting information

Don't Void Your Warranty!

Caution

This product is for indoor use. Do not install it outdoors or in a humid environment without the protective enclosure. Do not allow it to come into contact with any liquid.

Caution

Do not install or operate this product if it has been dropped, damaged, or exposed to liquids. These things happen, return it to Vaddio for safety and functional testing.

Cabling Notes

Use the connectors provided with the Twin Mono AMP to make cables for your installation.

We recommend shielded cabling if the cables will be coiled, run tightly with other cables, or rou sources of electromagnetic interference such as power lines or fluorescent light fixtures.

Caution

Check your cables. Connecting a cable to the wrong port or using the wrong pin-out can result equipment damage and will void the warranty.

Pro Tip

Label all cables at both ends.

Connector Pin-Outs

Input connector:

Pin 1 Audio	+
Pin 2 Audio	-
Pin 3 Ground
Pin 4 +12 VDC

Output connectors:

Pin 1 Audio	-
Pin 2 Audio	+

Exterior view of a black electronic device labeled 'ALDQ IN' with a blue indicator screen (no readable text beyond branding)

Exterior view of a black electronic device labeled 'SPARK-OUTS' with a blue logo (no readable text beyond branding)

Mounting the Twin Mono Amp

When installing the Twin Mono AMP with the ConferenceSHOT AV camera, mount the device dire under the camera.

Technical line drawing of a mechanical assembly with a circular component and a rectangular base (no text or symbols)

The Twin Mono AMP can also be mounted to an undermount bracket under a table.

Basic Connections

The Twin Mono AMP is compatible with unpowered analog speakers.

Connections for ConferenceSHOT AV Camera and Ceiling Speakers

This diagram shows the Twin Mono AMP used with a ConferenceSHOT AV camera and ceiling speakers. The ConferenceSHOT AV camera provides power and audio to the Twin Mono AMP.

graph LR
    A["Speaker"] --> B["TWIN MOND AMP"]
    C["Speaker"] --> B
    B --> D["Camera"]

The Twin Mono AMP chassis can be mounted to the ConferenceSHOT AV camera mount.

Connections for ConferenceSHOT ePTZ Camera and Sound Bar

This diagram shows the Twin Mono AMP powering a pair of speakers receiving audio from a ConferenceSHOT ePTZ camera. Other cameras with audio outputs connect the same way.

In this configuration, the Twin Mono AMP requires its own power supply. Use the 4-position conr from the included cable and one of the audio connectors shipped with the camera to build the that you will need.

graph TD
    A["TWIN MONO AMP"] -->|Power| B["15 VDC"]
    B --> C["15 V 2A"]
    C --> D["Audio Out"]
    B -->|GND▼| E["Output"]
    B -->|Audio In| F["Ground"]
    style A fill:#99ccff,stroke:#333
    style B fill:#99ccff,stroke:#333
    style C fill:#99ccff,stroke:#333
    style D fill:#99ccff,stroke:#333
    style E fill:#99ccff,stroke:#333
    style F fill:#99ccff,stroke:#333

Connections for AV Bridge Mini and Speakers

This diagram shows the Twin Mono AMP powering a pair of speakers receiving audio from an Mini. Other AV Bridge series devices connect the same way.

In this configuration, the Twin Mono AMP requires its own power supply. Use the 4-position conr from the included cable and one of the audio connectors shipped with the AV Bridge series dev build the adapter that you will need.

graph TD
    A["Speaker 1"] --> B["Speaker 2"]
    C["TWIN MONO AMP"] --> D["Power"]
    D --> E["Audio In"]
    E --> F["Audio Out"]
    F --> G["15 VDC"]
    G --> H["15 V 2A"]
    H --> I["GND"]
    I --> J["Output Device"]

Operation, Storage, and Care

For smears or smudges on the product, wipe with a clean, soft cloth. Use a lens cleaner on not use any abrasive chemicals.

Keep this device away from food and liquids.

Do not operate or store the device under any of the following conditions:

■ Temperatures above 104^ F ( 40^ C) or below 32^ F ( 0^ C)
■ High humidity, condensing or wet environments
■ Inclement weather
■ Severe vibration
■ Mounted to the frame of a Formula 1 vehicle
■ Dry environments with an excess of static discharge

Do not attempt to take this product apart. There are no user-serviceable components inside.