Lullaby Zip - Baby product CHICCO - Free user manual and instructions

USER MANUAL Lullaby Zip CHICCO

Line drawing of a baby care station with a baby bed, tray, and infant stand (no text or symbols)

Lullaby® Zip

3-in-1: Bassinet, Playard, Changing Table

Owner's Manual

WARNING

Failure to follow these warnings and the instructions could result in serious injury or death

• PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFETY OF YOUR CHILD.
  • ALWAYS PROVIDE THE SUPERVISION NECESSARY FOR THE CONTINUED SAFETY OF YOUR CHILD. WHEN USED FOR PLAYING, NEVER LEAVE CHILD UNATTENDED.
• Playard MUST be fully assembled with all top rails and center floor hub locked into position prior to use or attaching bassinet. Make sure latches are secure.
• DO NOT place child in playard unless all top rails and center floor hub are securely locked into position and floor pad is in proper place. Infant may roll into space between pad and loose mesh sides causing suffocation.
• Stop using this product when your child reaches 35 inches (89 cm) in height, weighs more than 30 lbs (14 kg), or is able to climb out.
• DO NOT use the bassinet when a child is in the playard.
• FALL HAZARD - To help prevent falls, do not use bassinet when infant begins to push up on hands and knees or weighs over 15 lbs (6.8 kg), whichever comes first.

• Child can become entrapped and die when improvised netting or covers are placed on top of product. Never add such items to confine child in product.

• DO NOT use bassinet on a bed, floor or other surfaces.
  • The bassinet is designed for use ONLY with this Chicco Lullaby Zip Playard.

• Stop using the changing table when your child reaches 25 lbs (11.4 kg).
• Never use this product if there are any loose or missing fasteners, loose joints, broken parts, or torn mesh/fabric. Check before assembly and periodically during use. Contact Chicco for replacement parts and instruction if needed. Never substitute parts.
• Although Chicco DOES NOT RECOMMEND refinishing this product, if you choose to refinish, use a nontoxic finish specified for children's products.

SUFFOCATION HAZARDS - Infants can suffocate:

• In gaps between extra padding and product side, and
• On soft bedding.
• Use ONLY the mattress provided by Chicco. Never add a pillow, comforter, or another mattress for padding.

- If a sheet is used with the pad, use only a fitted playard sheet specifically designed to fit snug with at least 2" (5 cm) under all sides of the mattress. The sheet must allow proper use of the mattress retention straps.

WARNING

Failure to follow these warnings and the instructions could result in serious injury or death

• DO NOT leave child in product with any side lowered. Be sure all sides are raised and locked in position whenever child is in product.
• NEVER use plastic shipping bags as mattress covers. Do not use plastic film as mattress cover unless sold and intended for that purpose. They can cause suffocation.
• DO NOT use a water mattress with this product.

STRANGULATION HAZARDS:

• NEVER use additional mattresses, padding, sheets, or other objects that will permit your child to climb out, fall and/or be injured. If you choose to ignore this warning, then remove additional padding, large toy, and other objects that could serve as steps for climbing out when your child is able to pull to a standing position.
• STOP using Bassinet when child can roll over or push up on hands and knees or reaches 15 lbs (6.8 kg), whichever comes first.
• Strangulation Hazard: Child can lift changing table and get neck trapped between changing table and playard frame.

• Never leave changing table in place when child is in the playard.

• Strings can cause strangulation! DO NOT place items with a string around child's neck (hood strings, pacifier cords,etc.) or attach strings to toys.

• DO NOT suspend strings into the bassinet or playard.
• DO NOT place the playard near a window where cords from blinds or drapes can strangle a child.

OTHER HAZARDS:

• Keep bassinet and playard away from stoves, heaters, fireplaces and other hazards which can cause injury to your child.
  • To reduce the risk of SIDS (Sudden Infant Death Syndrome), pediatricians recommend healthy infants be placed on their back to sleep unless otherwise advised by a physician.
• DO NOT place more than one child in bassinet or playard.
• DO NOT move or fold bassinet or playard with child in it - child could be injured.

Parts List

A.

Line drawing of a children's seat with wheels and seatbelt (no text or symbols)

A. - Lullaby Zip Frame

B.

Simple rectangular outline with dashed internal lines, no text or symbols present

B. - Mattress Pad

C.

Line drawing of a folded or layered object resembling a newspaper or document (no text or symbols)

C. - Bassinet

D.

Two technical line drawings of rectangular components with dotted outlines and corner holes (no text or symbols)

D. - Changing Pad w/ Removable insert

Parts List

E.

Line drawing of three identical mechanical clamps or brackets (no text or symbols)

E. - Changing Table Frame Ends

F.

Line drawing of three identical cylindrical objects with curved ends, no text or symbols present

F. - Changing Table Frame Sides

G.

Line drawing of a matching bag with patterned front panel and side pockets (no text or symbols)

G. - Parent Organizer

H.

Line drawing of a curved tool with a circular inset showing a pointer (no text or symbols)

H. - Toy Mobile and Canopy

Parts List

1. 

Three stylized elephant-shaped figures with visible internal patterns and no text or symbols

I. - Toys

J.

Simple line drawing of a rectangular object with internal curved lines and two triangular shapes (no text or symbols)

J. - Carry Bag

Setting Up the Playard

WARNING

Before use remove and dispose of any plastic bags and keep them out of reach of children to avoid the danger of suffocation. Failure to follow these warnings and instructions could result in serious injury or death. Make sure top rails and center floor hub are locked and secure before use. This product requires adult assembly. Keep fingers clear of top corners during setup.

1

1. Remove Lullaby Zip Frame from the Carry Bag.

Setting Up the Playard

2

1. With the Lullaby Zip Frame standing upright, pull the corners apart as shown.

If needed, pull up on the center floor hub release strap to lift the floor.

Setting Up the Playard

3

"CLICK!" "CLICK!"

1. The center floor hub must be pulled up to allow the top rails to lock.

With the center hub even (or level) with the 4 corners. Pull up on the top rail center joint to "Click" lock them into their open position. Both sides of the center joint must lock for the top rail to stay open. Repeat for all four top rails.

This step is very important for the safety of your child. Make sure the center hub is still pulled up during this step or the side rails will not be able to be latched.

"CLICK!" "CLICK!"

Setting Up the Playard

4

1. Push down on the center floor hub until the bottom of the playard is flat.

For Use as a Playard continue to the next step.

For Use as a Bassinet go to step 9 on page 15.

Diagram of a 3D container with mesh pattern and red directional arrows indicating flow or movement (no text or symbols)

Line drawing of a baby crib with patterned backrest and wheels (no text or symbols)

Setting Up the Playard

5

1. Install Mattress Pad, padded side up. Do not use playard without Mattress Pad and make sure to fold hook and loop strap underneath Mattress Pad.

Line drawing of a baby crib with mesh backrest and wheels (no text or symbols)

Setting Up the Playard

6 0 1 1 0

1. Locate 4 Mattress Pad strap holes on the floor of the playard. Thread the 4 hook and loop straps through to the floor of the playard as shown.

Diagram of a mechanical or structural component with two curved elements and red directional arrows indicating rotation (no text or symbols)

Setting Up the Playard

7

Line drawing of a hand holding a red tab near a mechanical component (no text or symbols)

1. Turn the playard on its side and pull the straps through the floor of the playard. Thread the straps through the slot on the playard foot as shown. Pull hook and loop strap tight and then attach together to secure Mattress Pad. Do this for all 4 mattress corners. Pull up on mattress pad to make sure it is secure.

Line drawing of a hand holding a tool over a mechanical component (no text or symbols)

Diagram of a mechanical assembly with a tool inserted into a component (no text or labels)

Pure mechanical linkage diagram with four red circular components and connecting rods (no text or symbols)

Setting Up the Bassinet

8

1. Undo the hook and loop straps from the frame and remove Mattress Pad from playard.

Setting Up the Bassinet

9A

A

9A. Unfold the Bassinet sides as shown.

Setting Up the Bassinet

9B

9B. Unfold the Bassinet ends over the playard frame. Fit the 4 corners of the Bassinet over the 4 corner Bassinet Supports on the Lullaby playard, as shown 9C. Once the Bassinet is resting on the supports push down on the center joints on the long sides of the Bassinet 9D. This will secure the Bassinet into place. Push down on Bassinet to be sure it is secure.

9c Bassinet Supports

9D

Setting Up the Bassinet

WARNING

Do not place Bassinet on unit if a child is in the playard. Make sure playard is fully assembled.

Illustration of a person folding a folded garment into a rectangular drawer (no text or symbols)

1. The Mattress Pad is slightly larger than the opening of the Bassinet. Do not fully open the Mattress Pad. Insert the Mattress Pad on an angle and slide it towards the side opposite of you. Adjust the mattress to fit the opposite corners before inserting the end closest to you. When the Mattress Pad is fully inserted on the bottom push it firmly into place. This will make the sides taut and remove any slack in the fabric. Always check to make sure the hook and loop straps are folded under the Mattress Pad.

Diagram of a baby crib with two red arrows indicating measurement or movement (no text or symbols present)

WARNING

Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries. Remove batteries before storing this product.

WARNING - Recommended use from birth to 5 months. The Mobile cannot be attached to the playard corner. The Bassinet has to be attached to the playard to use the Mobile. The mobile is intended for visual stimulation and is not intended to be grasped by the child. Always attach the provided fasteners (strings, straps, clamps, etc.) tightly to mobile and playard according to the instructions. Check frequently for loose or damaged parts. Possible entanglement or strangulation injury. DO NOT add additional strings or straps to mobile or playard. Remove toy when baby begins to push up on hands and knees.

Operate Mobile

Line drawing of a handheld device with a screwdriver inserted, labeled with number 11 (no text or symbols on the device itself)

1. Before attempting to operate the Mobile unit, install 3 "AA" batteries. Use a Phillips screwdriver to unfasten battery cover and remove the battery compartment. Insert the batteries and match the polarity indicated inside battery compartment.

Line drawing of a handheld device with a handle and internal components (no text or symbols)

Two 3D mechanical parts: a red box with internal channels and a black housing with internal compartments (no text or symbols)

Diagram of three cylindrical tanks inside a rectangular enclosure with plus and minus signs at the top (no text or symbols on the tanks themselves)

Assembling Toy Mobile

12

Abstract red and black line drawing of a symmetrical fan-like shape with a central dot (no text or symbols)

1. Insert the 3 canopy support sections into the fabric sleeve, as shown.

Illustration of hands performing a medical procedure on a curved mechanical component, with a red arrow indicating direction (no text or symbols present)

Illustration of a hand performing a medical or therapeutic procedure on a face, with a red arrow indicating the point of pressure (no text or symbols present)

Assembling Toy Mobile

1. Press in on the center of the canopy support to flip it into the fabric sleeve.

Assembling Toy Mobile

14

14

1. Insert the knot at the end of the Toy Mobile canopy string through the opening at the top of the Toy Mobile Arm, as shown. Pull on the fabric to secure the string.

Assembling Toy Mobile

15

1. Slide the Toy strap through the opening on one of the sides of the Toy Mobile. Fold the hook and loop strap together to secure the toy. Repeat for the remaining 2 Toys.

Assembling Toy Mobile

16

1. Attach the Mobile by sliding the base down over any of the playard corners with the Bassinet attached. Line up the post with corresponding Bassinet corner slot and push down until the Mobile base is completely seated around the corner of playard.

Assembling Toy Mobile

17

1. The curve of the Mobile Toy bar can be adjusted as shown. To remove the Mobile base pull out to release the bottom edge of the Mobile base and pull up.

Diagram of a mechanical device with directional arrows indicating motion or force (no text or symbols)

Operate Mobile

18

Simple line drawing of a semi-circular device with five icons: speaker, lightbulb, leaf, and musical note (no text or symbols)

1. Slide the switch to the left to turn the mobile "ON". Slide the switch to the right to turn "OFF" the mobile.

VOLUME: Press the Volume (◀) button to cycle through 3 volume settings: Low, Medium, High.

LIGHT: Press the LIGHT (💡) button to turn the Lights "ON" or "OFF". When the light is "ON" it will automatically turn off in 10 minutes.

NATURE SOUNDS: Press the Nature Sounds (💡) to cycle through 4 different sounds of nature. The selected Nature Sound will play for a 10 minutes then automatically turn off.

MUSIC: Press the Music (button to cycle through 8 different melodies. Select a starting melody, all 8 melodies will cycle through twice, starting with the first melody selected. To Lock in a melody and have it repeat 10 times, select a melody and press and hold the Music (Button for 2 seconds.

Attaching Parent Organizer

19A

Diagram showing a device with a handle and a side panel, illustrating a mechanical or electrical assembly (no text or symbols present)

19A. Attach the Parent Organizer to the side top rail of the playard as shown.

Parent organizer can be attached to either side. For greater convenience, we recommend the side nearest to the changing table latches.

Line drawing of a baby crib with mesh backrest and side arm (no text or symbols)

19B

Line drawing of a baby crib with red arrows indicating measurement or adjustment points (no text or symbols)

19B. To easily access the top compartments, unzip the top of the Parent Organizer. Fold and tuck the fabric behind the Parnet Organizer, as shown.

Diagram of a baby seatbelt with a red arrow indicating the seatbelt area (no text or symbols present)

Changing Table Warnings

WARNING

FALL HAZARD : Children have suffered serious injuries after falling from changing tables. Falls can happen quickly.

• STAY within arm's reach of your child.
- ALWAYS secure this changing table to the playard frame by attaching to the playard receptacles. See instructions.

SUFFOCATION HAZARD: Babies have suffocated while sleeping on changing tables. Changing table is not designed for safe sleep.

- NEVER allow baby to sleep on changing table.

- Stop using the changing table when your child reaches 25 lbs (11.4 kg).

• Always remove the changing table when your child is in the playard.

- Do not use changing unit if it is damaged or broken.

Assembling Changing Table

20

Tab

"CLICK!"

Technical line drawing of a car rear bumper component (no text or symbols)

Pure technical line drawing of a vertical mechanical component (no text or symbols)

Line drawing of a mechanical frame structure with no text or symbols

1. Slide the end of the Changing Table Frame Side into the groove of the Changing Table Frame End until it clicks into place. Make sure the tab is on the inside when assembling.

Repeat for the other Changing Table Frame Side as shown.

Do NOT Snap the other end onto the changer frame. Move to step 21 to install softgoods before finishing the changer frame assembly.

Assembling Changing Table

21A

Diagram of a container with an upward arrow inside, no text or symbols present

21A. Insert the Changing Table Frame Sides into the openings on the back of the Changing Pad and slide up.

21B "CLICK!"

21B. Attach the Changing Table Frame End to the Changing Table Frame Sides as shown making sure it clicks into place.

Assembling Changing Table

22

1. Locate the fabric tabs along the outside of the Changing Pad. Thread the fabric tabs through the corresponding openings on the frame and pull the fabric tabs through. Flatten the fabric tabs out to secure them into place. Repeat for both sides.

Diagram of a hand holding a car seatbelt with a red arrow indicating the left side (no text or symbols present)

Diagram of a car interior showing two red-circled areas of the dashboard and seat brackets (no text or symbols present)

Assembling Changing Table

23

Diagram showing a container with four red circles highlighting specific areas, likely indicating locations or zones within the container.

1. Flip the Changing Table right side up. Arrange the Zipper insert so that all 4 of the hook and loop tabs are lined up and connected. Then zip closed both sections of the Zipper Insert.

Abstract diagram of a rectangular container with internal wavy lines and two red-circled highlights (no text or symbols)

Simple line drawing of a rectangular frame with dashed border (no text or symbols)

Attaching Changing Table

24

"CLICK!"

1. IMPORTANT: The Changing Table can only be attached to one end of the playard. Locate the changing table receptacles on the side of the playard. Assemble the Changing Table by lining up the corners of the changing table frame with the corners of the playard. Press down until the changing table latches into the playard receptacles. Pull up on Changing Table to check for attachment. Never use the changer on another surface or playard.

Diagram of a car front panel with two red circles highlighting the side panels (no text or symbols present)

Removing Changing Table

25

Line drawing of a car interior with a seatbelt and side panel, showing red directional arrows indicating movement or force (no text or symbols)

1. Remove the Changing Table by pushing in on the release buttons and lifting up.

Packing Up the Playard

26

1. Remove the Bassinet, Toy Mobile, Parent Organizer, Changing Table and Mattress Pad. Pull up on the center floor hub release strap and lift the center hub up as far as possible.

Diagram of a mechanical component with a red arrow indicating direction, no text or symbols present

Diagram of a container with a handle and arrow indicating upward motion (no text or symbols)

Packing Up the Playard

27

1. Lift and squeeze the Top Rails center release lock, then push down. Release all of the Top Rail locks on all 4 sides. If the Top Rail does not unlock pull up on the center hub to release the floor locks. Center floor hub must be even with top rails.

Diagram of a furniture component with red arrows indicating downward force or movement, no text or symbols present

Line drawing of a garment pattern piece with measurement arrows indicating measurement points (no text or symbols)

Packing Up the Playard

28

Diagram of a V-shaped mechanical device with red arrows indicating force or movement, showing internal components and motion direction (no text or symbols)

1. Pull up on the center floor hub release strap and pull the playard legs towards the center.

Line drawing of a stroller with four seats and wheels, no text or symbols present

Packing Up the Playard

29

Diagram of a mechanical component with dashed lines indicating internal structure (no text or symbols)

1. Place the Mattress Pad into the Carry Bag, making sure the padded side of the mattress is facing up. Then place the folded playard into the Mattress Pad and all other accessories on top. Use the hook and loop straps to keep the accessories from sliding around. Tuck in the Changer on either side of the Mattress Pad.

Anatomical line drawing of a human head and neck region showing internal organs (no text or labels)

Line drawing of a person wearing a vest with straps and a seatbelt (no text or symbols)

Line drawing of a mechanical device with no visible text or symbols

Packing Up the Playard

30

Line drawing of a rectangular object with internal cavity and two curved cutouts (no text or symbols)

1. Pull up the sides of the Carry Bag and close the zipper.

Packing Up the Playard

31

clicks

1. To keep instructions for future use: Place the manual in the storage sleeve located on the underside of the Mattress Pad.

WARNING

The Electronic Play Tray requires 3 x "AA" 1.5 Volt alkaline type batteries (not included).

• Batteries must only be fitted by an adult.
• To fit and/or replace batteries: Loosen the screw on the battery compartment cover with a suitable screwdriver, press the tab and remove the battery compartment cover. Then remove the spent batteries and fit new ones, ensuring that they have been fitted in the correct polarity, as shown inside the battery compartment. Replace the battery cover and tighten the screw.
  • Always keep batteries and tools out of reach of children.
  • Always remove spent batteries from the Mobile to avoid the danger of possible leakage from the battery.
  • Always remove the batteries if the Mobile will not be used for a long period.
• Only use alkaline batteries of the same type or equivalent to the type recommended for the correct function of this product.
• Never mix new and old batteries, or different types of batteries.
• Do not burn or dispose of spent batteries into the environment. Dispose of spent batteries at an appropriate differentiated collection point.
• Do not short-circuit the battery terminals.
• Do not attempt to recharge non-rechargeable batteries: they might explode.
• The use of rechargeable batteries is not recommended, since they could impair the functionality of the Mobile.
• If rechargeable batteries are used, take them out of the toy before recharging them. Batteries must always be recharged under adult supervision.

Trouble Shooting Guide

TOP RAILS FAIL TO LOCK INTO AN UPRIGHT POSITION :

Before top rails can be locked, the center floor hub must be pulled up as high as the 4 corners. If needed, pull up on the center floor hub release strap. If necessary, pull the release strap up with one hand and lock rails one at a time. If you are still unable to lock the top rails, call Chicco Customer Service (pg. 45).

THE FLOOR JOINTS DO NOT FLATTEN:

Turn playard upside down and make sure joints are free from foreign objects.

TOP RAILS DO NOT UNLOCK TO FOLD:

Lift top rail first, then squeeze to release. Before top rails can be unlocked, the center floor hub must be pulled up. If needed pull up on the center floor hub release strap as high as the 4 corners.

FLOOR JOINTS DO NOT UNLOCK:

Pull up on the center floor hub release strap to unlock floor joints.

FOLDED PLAYARD DOES NOT FIT INTO MATTRESS PAD:

Pull up on the center floor hub release strap and gather playard legs towards the center to make the playard more compact. If necessary, shift playard lower on pad or turn slightly and try again.

BASSINET DOES NOT FIT ONTO PLAYARD:

Playard top rails must be fully upright and locked. Playard floor must be flat.

LULLABY ZIP MOBILE DOES NOT FIT INTO CORNER SLOT:

Make sure fabric is not covering the slot in the bassinet corner. The mobile will fit onto any of the corners - Try another corner.

Cleaning and Maintenance

This product requires regular maintenance. The cleaning and maintenance of the playard must only be carried out by an adult.

The mattress cover and changer insert can be washed, remove the boards from the mattress cover as shown.

Line drawing of hands holding a rectangular object on a table (no text or symbols)

Locate the zipper on the mattress cover and unzip. Remove all of the floor boards and set them aside.

Simple line drawing of a rectangular frame with rounded corners and no text or symbols

Undo the zippers and remove the Changer Insert.

Do not immerse the wooden boards in water. Wipe clean with a damp cloth and mild detergent (do not use bleach).

CLEANING

Please refer to the care label for instructions on cleaning the fabric parts of the playard.

Periodically wipe clean plastic parts with a soft damp cloth. Always dry the metal parts to prevent the formation of rust if the playard has come into contact with water.

MAINTENANCE

Periodically check the playard for loose screws, worn parts, torn material or stitching. Replace or repair the parts as needed. Use only Chicco replacement parts. Keep the playard in a dry place. If playard becomes wet open playard and allow to dry completely. Prolonged exposure to direct sunlight may cause the fabric to fade and plastic parts to warp.

FCC Information

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or experienced radio/TV technician for help.

For More Information

If you have any questions or comments about this product, or are missing any of the parts please do not return this product to the store. Contact us in one of the following ways:

(877)-424-4226

[e-mail]

www.chiccousa.com

1826 William Penn Way

Lancaster, PA 17601

chicco®

www.chiccousa.com