Lullaby - Baby product CHICCO - Free user manual and instructions

USER MANUAL Lullaby CHICCO

Line drawing of a baby crib with mesh bedding and side compartments (no text or symbols)

Lullaby®

3-in-1: Bassinet, Playard, Changing Table

Owner's Manual

WARNING

Failure to follow these warnings and the instructions could result in serious injury or death

• PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFETY OF YOUR CHILD.
  • ALWAYS PROVIDE THE SUPERVISION NECESSARY FOR THE CONTINUED SAFETY OF YOUR CHILD. WHEN USED FOR PLAYING, NEVER LEAVE CHILD UNATTENDED.
• Playard MUST be fully assembled with all top rails and center floor hub locked into position prior to use or attaching bassinet. Make sure latches are secure.
• DO NOT place child in playard unless all top rails and center floor hub are securely locked into position and floor pad is in proper place. Infant may roll into space between pad and loose mesh sides causing suffocation.
• Stop using this product when your child reaches 35 inches (89 cm) in height, weighs more than 30 lbs (14 kg), or is able to climb out.
• DO NOT use the bassinet when a child is in the playard.
• FALL HAZARD - To help prevent falls, do not use bassinet when infant begins to push up on hands and knees or weighs over 15 lbs (6.8 kg), whichever comes first.

• Child can become entrapped and die when improvised netting or covers are placed on top of product. Never add such items to confine child in product.

• DO NOT use bassinet on a bed, floor or other surfaces.

• The bassinet is designed for use ONLY with this Chicco Lullaby Playard.
• Stop using the changing table when your child reaches 25 lbs (11.4 kg).
• Never use this product if there are any loose or missing fasteners, loose joints, broken parts, or torn mesh/fabric. Check before assembly and periodically during use. Contact Chicco for replacement parts and instruction if needed. Never substitute parts.
• Although Chicco DOES NOT RECOMMEND refinishing this product, if you choose to refinish, use a nontoxic finish specified for children's products.

SUFFOCATION HAZARDS - Infants can suffocate:

• In gaps between extra padding and product side, and
• On soft bedding.
• Use ONLY the mattress provided by Chicco. Never add a pillow, comforter, or another mattress for padding.

- If a sheet is used with the pad, use only a fitted playard sheet specifically designed to fit snug with at least 2" (5 cm) under all sides of the mattress. The sheet must allow proper use of the mattress retention straps.

WARNING

Failure to follow these warnings and the instructions could result in serious injury or death

• DO NOT leave child in product with any side lowered. Be sure all sides are raised and locked in position whenever child is in product.
- NEVER use plastic shipping bags as mattress covers. Do not use plastic film as mattress cover unless sold and intended for that purpose. They can cause suffocation.
- DO NOT use a water mattress with this product.

STRANGULATION HAZARDS:

• NEVER use additional mattresses, padding, sheets, or other objects that will permit your child to climb out, fall and/or be injured. If you choose to ignore this warning, then remove additional padding, large toy, and other objects that could serve as steps for climbing out when your child is able to pull to a standing position.
• STOP using Bassinet when child can roll over or push up on hands and knees or reaches 15 lbs (6.8 kg), whichever comes first.
• Strangulation Hazard: Child can lift changing table and get neck trapped between changing table and playard frame.

• Never leave changing table in place when child is in the playard.

• Strings can cause strangulation! DO NOT place items with a string around child's neck (hood strings, pacifier cords,etc.) or attach strings to toys.

• DO NOT suspend strings into the bassinet or playard.
• DO NOT place the playard near a window where cords from blinds or drapes can strangle a child.

OTHER HAZARDS:

• Keep bassinet and playard away from stoves, heaters, fireplaces and other hazards which can cause injury to your child.
  • To reduce the risk of SIDS (Sudden Infant Death Syndrome), pediatricians recommend healthy infants be placed on their back to sleep unless otherwise advised by a physician.
• DO NOT place more than one child in bassinet or playard.
• DO NOT move or fold bassinet or playard with child in it - child could be injured.

Parts List

A.

Line drawing of a person wearing a backpack (no text or symbols)

A. - Lullaby Frame

B.

Simple geometric shape with a rounded rectangle and three vertical dashed lines inside (no text or symbols)

B. - Mattress Pad

C.

Line drawing of a folded or folded object resembling a bag or fabric (no text or symbols)

C. - Bassinet

D.

Simple line drawing of a rectangular tray or container with no text or symbols

D. - Changing Pad

Parts List

E.

Line drawing of two mechanical clips or tools with no text or symbols

E. - Changing Table Frame Ends

F.

Line drawing of three identical cylindrical mechanical components with flanges (no text or symbols)

F. - Changing Table Frame Sides

G.

Line drawing of a mesh basket with two handles and a side panel (no text or symbols)

G. - Parent Organizer

H.

Simple line drawing of a rectangular object with internal curved lines and two triangular cutouts (no text or symbols)

H. - Carry Bag

Setting Up the Playard

WARNING

Before use remove and dispose of any plastic bags and keep them out of reach of children to avoid the danger of suffocation. Failure to follow these warnings and instructions could result in serious injury or death. Make sure top rails and center floor hub are locked and secure before use. This product requires adult assembly. Keep fingers clear of top corners during setup.

1. Remove Lullaby Frame from the Carry Bag.

Setting Up the Playard

Line drawing of a person wearing a suit jacket, with red arrows indicating movement or direction (no text or symbols)

1. With the Lullaby Frame standing upright, pull the corners apart as shown.

If needed, pull up on the center floor hub release strap to lift the floor.

Setting Up the Playard

3

"CLICK!" "CLICK!"

"CLICK!" "CLICK!"

1. The center floor hub must be pulled up to allow the top rails to lock.

With the center hub even (or level) with the 4 corners. Pull up on the top rail center joint to "Click" lock them into their open position. Both sides of the center joint must lock for the top rail to stay open. Repeat for all four top rails.

This step is very important for the safety of your child. Make sure the center hub is still pulled up during this step or the side rails will not be able to be latched.

Setting Up the Playard

4

1. Push down on the center floor hub until the bottom of the playard is flat.

For Use as a Playard continue to the next step.

For Use as a Bassinet go to step 9 on page 14.

Diagram of a container with mesh pattern and a red arrow indicating a point of interest (no text or symbols present)

Line drawing of a baby crib with mesh pattern and side supports (no text or symbols)

Setting Up the Playard

5

1. Install Mattress Pad, padded side up. Do not use playard without Mattress Pad and make sure to fold hook and loop strap underneath Mattress Pad.

Line drawing of a baby crib with mesh pattern and red stitching (no text or symbols)

Setting Up the Playard

6 0 1 0 0 0 0

1. Locate 4 Mattress Pad strap holes on the floor of the playard. Thread the 4 hook and loop straps through to the floor of the playard as shown.

Setting Up the Playard

7

Line drawing of a hand holding a tool with a red tab, no text or symbols present

1. Turn the playard on its side and pull the straps through the floor of the playard. Thread the straps through the slot on the playard foot as shown. Pull hook and loop strap tight and then attach together to secure Mattress Pad. Do this for all 4 mattress corners. Pull up on mattress pad to make sure it is secure.

Line drawing of a hand holding a tool over a mechanical component (no text or symbols)

Technical line drawing of a mechanical component with a handle and lever (no text or symbols)

Pure structural diagram of a frame with four red circular annotations highlighting specific components (no text or symbols)

Setting Up the Bassinet

Line drawing of a furniture box with a red arrow indicating upward motion (no text or symbols)

1. Undo the hook and loop straps from the frame and remove Mattress Pad from playard.

Setting Up the Bassinet

9A

9A. Unfold the Bassinet sides as shown.

Setting Up the Bassinet

9B

9B. Unfold the Bassinet ends over the playard frame. Fit the 4 corners of the Bassinet over the 4 corner Bassinet Supports on the Lullaby playard as shown 9C. Once the Bassinet is resting on the supports push down on the center joints on the long sides of the Bassinet 9D. This will secure the Bassinet into place. Push down on Bassinet to be sure it is secure.

9c Bassinet Supports

9D

Setting Up the Bassinet

WARNING

Do not place Bassinet on unit if a child is in the playard. Make sure playard is fully assembled.

Illustration of a person folding a folded garment into a rectangular tray (no text or symbols)

1. The Mattress Pad is slightly larger than the opening of the Bassinet. Do not fully open the Mattress Pad. Insert the Mattress Pad on an angle and slide it towards the side opposite of you. Adjust the mattress to fit the opposite corners before inserting the end closest to you. When the Mattress Pad is fully inserted on the bottom push it firmly into place. This will make the sides taut and remove any slack in the fabric. Always check to make sure the hook and loop straps are folded under the Mattress Pad.

Diagram of a baby crib with two red arrows indicating downward pressure or movement (no text or symbols present)

Attaching Parent Organizer

11

Line drawing of a baby crib with a side panel and a red arrow indicating rotation (no text or symbols)

1. Attach the Parent Organizer to the side top rail of the playard as shown.

Parent organizer can be attached to either side. For greater convenience, we recommend the side nearest to the changing table latches.

Technical line drawing of a mechanical component with red annotation lines indicating features (no text or symbols present)

Changing Table Warnings

WARNING

FALL HAZARD : Children have suffered serious injuries after falling from changing tables. Falls can happen quickly.

• STAY within arm's reach of your child.
- ALWAYS secure this changing table to the playard frame by attaching to the playard receptacles. See instructions.

SUFFOCATION HAZARD: Babies have suffocated while sleeping on changing tables. Changing table is not designed for safe sleep.

- NEVER allow baby to sleep on changing table.

- Stop using the changing table when your child reaches 25 lbs (11.4 kg).

• Always remove the changing table when your child is in the playard.

- Do not use changing unit if it is damaged or broken.

Assembling Changing Table

12

Tab

"CLICK!"

Technical line drawing of a car rear bumper component (no text or symbols)

1. Slide the end of the Changing Table Frame Side into the groove of the Changing Table Frame End until it clicks into place. Make sure the tab is on the inside when assembling.

Pure mechanical component diagram without any text, numbers, or symbols

Repeat for the other Changing Table Frame Side as shown.

Do NOT Snap the other end onto the changer frame. Move to step 13 to install softgoods before finishing the changer frame assembly.

Line drawing of a mechanical frame structure with no text or symbols

Assembling Changing Table

13A

Diagram of a container with an upward arrow inside, no text or symbols present

13A. Insert the Changing Table Frame Sides into the openings on the back of the Changing Pad and slide up.

13B "CLICK!"

13B. Attach the Changing Table Frame End to the Changing Table Frame Sides as shown making sure it clicks into place.

Assembling Changing Table

14 ①

1. Locate the fabric tabs along the outside of the Changing Pad. Thread the fabric tabs through the corresponding openings on the frame and pull the fabric tabs through. Flatten the fabric tabs out to secure them into place. Repeat for both sides.

Diagram of a hand holding a car seatbelt with a red arrow indicating the left side (no text or symbols present)

Technical line drawing of a car interior with two red-circled annotations highlighting specific components (no text or symbols present)

Assembling Changing Table

1. IMPORTANT: The changing table can only be attached to one end of the playard. Locate the changing table receptacles on the side of the playard. Assemble the changing table by lining up the corners of the changing table frame with the corners of the playard. Press down until the changing table latches into the playard receptacles. Pull up on changing table to check for attachment. Never use the changer on another surface or playard.

Storing Changing Table

16

Diagram of a mechanical component with red arrows indicating direction, no text or symbols present

1. Remove the changing table by pushing in on the release buttons and lifting up. The changing table can be stored by hanging on the Parent Organizer as shown.

Technical line drawing of a car interior showing seat, frame, and guardrail (no text or symbols)

Packing Up the Playard

Line drawing of a furniture cabinet with a lid and mesh pattern, no text or symbols present

1. Remove the Bassinet, Parent Organizer, Changing Table, and Mattress Pad. Pull up on the center floor hub release strap and lift the center hub up as far as possible.

Diagram of a funnel-shaped structure with a red arrow indicating upward motion, no text or symbols present

Line drawing of a baby crib with mesh backrest and red arrow indicating upward motion (no text or symbols)

Packing Up the Playard

1. Lift and squeeze the Top Rails center release lock, then push down. Release all of the Top Rail locks on all 4 sides. If the Top Rail does not unlock pull up on the center hub to release the floor locks. Center floor hub must be even with top rails.

Packing Up the Playard

19

Diagram of a V-shaped mechanical component with red arrows indicating force or movement, showing internal structure and mounting points (no text or symbols)

Line drawing of a person wearing a hooded garment, viewed from above (no text or symbols)

1. Pull up on the center floor hub release strap and pull the playard legs towards the center.

Packing Up the Playard

20

20. Place the Mattress Pad into the Carry Bag - Make sure the padded side of the mattress pad is facing up. Then place the folded playard into the Mattress Pad. Place all other accessories on top.

Packing Up the Playard

Line drawing of a rectangular object with internal channels and a looped base, labeled with number 21 (no text or symbols on the object itself)

1. Pull up the sides of the Carry Bag and close the zipper.

Packing Up the Playard

22

clicka

1. To keep instructions for future use: Place the manual in the storage sleeve located on the underside of the Mattress Pad.

Trouble Shooting Guide

TOP RAILS FAIL TO LOCK INTO AN UPRIGHT POSITION :

Before top rails can be locked, the center floor hub must be pulled up as high as the 4 corners. If needed, pull up on the center floor hub release strap. If necessary, pull the release strap up with one hand and lock rails one at a time. If you are still unable to lock the top rails, call Chicco Customer Service (pg. 32).

THE FLOOR JOINTS DO NOT FLATTEN:

Turn playard upside down and make sure joints are free from foreign objects.

TOP RAILS DO NOT UNLOCK TO FOLD:

Lift top rail first, then squeeze to release. Before top rails can be unlocked, the center floor hub must be pulled up. If needed pull up on the center floor hub release strap as high as the 4 corners.

FLOOR JOINTS DO NOT UNLOCK:

Pull up on the center floor hub release strap to unlock floor joints.

FOLDED PLAYARD DOES NOT FIT INTO MATTRESS PAD:

Pull up on the center floor hub release strap and gather playard legs towards the center to make the playard more compact. If necessary, shift playard lower on pad or turn slightly and try again.

BASSINET DOES NOT FIT ONTO PLAYARD:

Playard top rails must be fully upright and locked. Playard floor must be flat.

Cleaning and Maintenance

This product requires regular maintenance. The cleaning and maintenance of the playard must only be carried out by an adult.

The mattress cover and changer insert can be washed, remove the boards from the mattress cover as shown.

Line drawing of hands holding a red rectangular object on a table with geometric shapes (no text or symbols)

Locate the zipper on the mattress cover and unzip. Remove all of the floor boards and set them aside.

Do not immerse the wooden boards in water. Wipe clean with a damp cloth and mild detergent (do not use bleach).

CLEANING

Please refer to the care label for instructions on cleaning the fabric parts of the playard.

Periodically wipe clean plastic parts with a soft damp cloth. Always dry the metal parts to prevent the formation of rust if the playard has come into contact with water.

MAINTENANCE

Periodically check the playard for loose screws, worn parts, torn material or stitching. Replace or repair the parts as needed. Use only Chicco replacement parts. Keep the playard in a dry place. If playard becomes wet open playard and allow to dry completely. Prolonged exposure to direct sunlight may cause the fabric to fade and plastic parts to warp.

For More Information

If you have any questions or comments about this product, or are missing any of the parts please do not return this product to the store. Contact us in one of the following ways:

(877)-424-4226

[e-mail]

www.chiccousa.com

1826 William Penn Way

Lancaster, PA 17601

chicco®

www.chiccousa.com