VIMHK-97 - Interface vidéo CRUX - Free user manual and instructions
Find the device manual for free VIMHK-97 CRUX in PDF.
User questions about VIMHK-97 CRUX
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Interface vidéo in PDF format for free! Find your manual VIMHK-97 - CRUX and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. VIMHK-97 by CRUX.
USER MANUAL VIMHK-97 CRUX
Vehicle Applications
2016 Kia Sorrento
Navigation / Radio Compatibility
- with 8" Navigation screen.
text_image
10SAParts Included
VIMHK-97 Interface Module
natural_image
Coiled electrical cable with multiple colored wires, no visible text or symbolsHK-97 Harness
Wiring Diagram
text_image
ON 1 2 3 4 5 8 7 6 5 4 3 2 1Pin assignment male 8-pin connector of VIMHK-97
| Cable colour | Pin-No. | Assignment |
| Yellow | Pin 4 | CAN-HIGH – connection to the head-unit |
| Blue | Pin 3 | CAN-LOW – connection to the head-unit |
| Yellow/Black | Pin 8 | CAN-HIGH – connection to the vehicle |
| Blue/Black | Pin 7 | CAN-LOW – connection to the vehicle |
| Red | Pin 1 | +12V Constant |
| Black | Pin 5 | Ground |
| Green | Pin 6 | Activation of the Video-in-Motion function (+12V = VIM Enabled) |
| White | Pin 2 | Trigger output (+12V DC 500mA) |
flowchart
graph TD
A["To Headunit"] --> B["CAN Low"]
B --> C["CAN High"]
C --> D["BLUE"]
C --> E["YELLOW"]
C --> F["YELLOW/BLACK"]
C --> G["BLUE/BLACK"]
H["To Vehicle"] --> I["CAN Low"]
I --> J["CAN High"]
J --> K["+12V"]
L["GND"] --> M["+12V = VIM Enabled"]
N["Sightline"] --> O["CAUX"]
style A fill:#f9f,stroke:#333
style H fill:#ccf,stroke:#333
style N fill:#cfc,stroke:#333
Installation Instructions
| Connector | Assignment |
| Connector B, Pin 11/12 | +12V Constant (Red) |
| Connector B, Pin 23/24 | Ground (Black) |
| Connector B, Pin 1 | CAN-HIGH (Yellow) |
| Connector B, Pin 13 | CAN-LOW (Blue) |
| Connector B, Pin 16 | Speedsignal (Gray) |
text_image
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1 2 3 4 5 6 7 8 9 10 11 12 12 14 15 16 17 18 19 20 21 22 23 24Connector A
Connector B
Please note that the given information must be verified by the installer. Crux Interfacing assumes no liability for changes in wire color or pin assignments made by the vehicle manufacturer.
For video in motion, cut and insulate the analog speed signal wire (pin 17, connector B) (navigation will still work over GPS reception). An optional toggle switch can be installed in between the cut speed signal wire in case the GPS reception is bad or not available.
DIP Switch Setting
| Vehicle/ Navigation | Dip 1 | Dip 2 | Dip 3 | Dip 4 | Dip 5 | Dip 6 |
| All vehicles | ON | OFF | OFF | OFF | OFF | OFF |
DIP Switch Functions:
Dip 1 - ON = Video In Motion enabled
Dip 2 - ON = If factory rear-view camera is present
Dip 3 – no function (set to OFF)
Dip 4 - no function (set to OFF)
Dip 5 - CAN-bus termination resistor on the vehicle side
Dip 6 - CAN-bus termination resistor on the head-unit side
Activation of the Video-In-Motion function
The Video-In-Motion can be activated and deactivated by DIP 1 or by the loose green wire on the harness when connected to a +12V ACC source.
Video-In-Motion permanent
With DIP1 set to ON, the video-in-motion function is activated permanently without disturbing the navigation performance.
Video-in-motion selective
With DIP1 set to OFF, the green wire is used to activate and deactivate the video-in-motion function.
Connect a toggle switch between the green wire and +12V ACC.
- +12V = Video-in-motion is activated
- 0V = Video-in-motion is not activated