MM-TAC1 - Aide pour plancher Helder - Free user manual and instructions

USER MANUAL MM-TAC1 Helder

Abstract red logo design with curved shapes inside a rounded square (no text or symbols)

HELDER®

Pure white mechanical linkage diagram on red background, no text or symbols present

mm-TAC 1

Triple-Monitor Tabletop Clamp Mount

for 13 to 27 in. Computer Monitors

Thank you for choosing Helder

Helder's Triple-Monitor Tabletop Mount provides customizable articulating support for three monitors and offers adjustable height, tilt and swivel angles for optimal viewing. The sturdy steel construction accommodates computer monitors with screen sizes measuring 13 to 27 inches and weighing up to 15.4 pounds per mount, and features easy to remove VESA mounts. This stand offers nonpermanent clamp and grommet attachments for tabletops 0.39 to 3.46 inches thick, so you can easily install and remove your monitors.

If you have safety concerns about installing this product, contact a qualified professional or installation contractor. If this product is missing hardware or there are defective parts, call Customer Service at 212-594-2353.

Product Specifications

Compatible Computer

Monitor Sizes:

13 to 27 in. (33 to 68.6 cm)

Max Height:

17 in. (43.2 cm)

Max Weight Capacity:

15.4 lb. (7 kg) per arm

VESA Mounting

Patterns:

75×75 mm

100×100 mm

Weight:

11.2 lb. (5.1 kg)

Clamp Width:

0.39 × 3.46 in. (1.0 × 8.8 cm)

Material:

Steel, plastic

Grommet Width:

0.39×2.95 in.(1.0×7.5 cm)

Steel, plastic ±90° +45° -45° 17.4 in. (44.3 cm) 100 75 75 100 11.5 in. (29.3 cm) 1.45 in. (3.7 cm) 11.5 in. (29.3 cm) 1.4 in. (3.5 cm) 3.5 in. (9 cm) 3.3 in. (8.3 cm) 49.1 in. (124.6 cm) ±180° 0.39 × 3.46 in. (1.0 × 8.8 cm) 0.39 × 2.95 in. (1.0 × 7.5 cm) 3

Safety Warnings

When installing this product, be sure to refer to the assembly instructions detailed in this manual; failure to abide by the assembly instructions may void the product's warranty.

Do not use this product for any computer monitor other than what it is intended for; the exact specification, size parameters, and weight limits are found both on the product box and in the instruction manual.

It is recommended that at least 2 people perform the installation process to prevent injury from mishandling or dropping the product and/or flat-screen device.

Make sure your fingers are protected and support the display when raising or lowering the riser mount.

Do not use the monitor mount on an uneven surface.

This product may contain small parts which can pose a choking hazard; keep out of reach of children and pets.

Excessive exposure to liquids may damage the finish of this product; when cleaning this product, use only a mild detergent solution, and quickly wipe dry with a soft cloth.

Helder takes no responsibility for any product damage or personal injury resulting from mishandling, incorrect mounting, faulty assembly, or improper use of this product.

All images are for illustrative purposes only.

Parts List

A. (×3) B. (×1) C. (×1) D. (×1) E. (×1) F. (×1) G. (×1) H. (×3) I. (×5) J. (×3) K. (×1) L. (×1) m. (×1) n. (×1) m-A (×12) m-B (×12) m-C (×12) m-D (×12) m-E (×12) m-F (×12) M4×12 mm M4×16 mm M5×12 mm M5×16 mm D5

Assembling the Clamp

D C J L

C. (×1) D. (×1) I. (×5) J. (×3) L. (×1)

Technical line drawing of a mechanical device with no visible text or symbols

Assembling the Grommet

C F I

C. (×1) D. (×1) F. (×1) I. (×5) K. (×1)

D K

Attaching the Monitor Mount G B. E. G. m. (×1) (×1) (×1) (×1) B. E. m 7

Installing the VESA Mounts

A. A. m-B. m-C. m-D. m-FE. (×12)(×3)12 (×12) (×12) (×12)

m-E m-A m-C m-E m-B m-D m-F For Displays with a Curve 8

Too short / too long / crooked

✓ × TV TV TV

Red Back

Attaching the Monitors

H. (×3) n. (×1)

graph TD
    A["Step 1"] --> B["Step 2"]
    B --> C["Step 3"]
    C --> D["n"]
    style A fill:#f9f,stroke:#333
    style B fill:#f9f,stroke:#333
    style C fill:#f9f,stroke:#333
    style D fill:#ccf,stroke:#333

Monitor Adjustment

Tilt

+45°

-45°

Pure mechanical diagram showing a rotating shaft and housing assembly without any text or symbols

Swivel

+90°

-90°

Diagram showing a mechanical assembly inside a frame with red arrows indicating motion or flow (no text or symbols)

Rotation

+180°

-180°

Height

Technical diagram illustrating mechanical assembly with labeled components and directional arrows, showing motor and gear assembly.

Arm Height

m. (×1)

Technical diagram of a mechanical assembly with labeled components and an inset showing a close-up of a motor mechanism.

Arm Articulation

Correct Alignment Options

Pure mechanical diagram showing a lever system with pivot point and pivot supports (no text or symbols)

Warning

Weight Distribution of each monitor should be balanced across the center line

graph TD
    A["Component 1"] --> B["Component 2"]
    B --> C["Component 3"]
    C --> D["Component 4"]
    D --> E["Component 5"]
    E --> F["Component 6"]
    F --> G["Component 7"]
    G --> H["Component 8"]
    H --> I["Component 9"]
    I --> J["Component 10"]
    J --> K["Component 11"]
    K --> L["Component 12"]
    L --> M["Component 13"]
    M --> N["Component 14"]
    N --> O["Component 15"]
    O --> P["Component 16"]
    P --> Q["Component 17"]
    Q --> R["Component 18"]
    R --> S["Component 19"]
    S --> T["Component 20"]
    T --> U["Component 21"]
    U --> V["Component 22"]
    V --> W["Component 23"]
    W --> X["Component 24"]
    X --> Y["Component 25"]
    Y --> Z["Component 26"]
    Z --> AA["Component 27"]
    AA --> AB["Component 28"]
    AB --> AC["Component 29"]
    AC --> AD["Component 30"]
    AD --> AE["Component 31"]
    AE --> AF["Component 32"]
    AF --> AG["Component 33"]
    AG --> AH["Component 34"]
    AH --> AI["Component 35"]
    AI --> AJ["Component 36"]
    AJ --> AK["Component 37"]
    AK --> AL["Component 38"]
    AL --> AM["Component 39"]
    AM --> AN["Component 40"]
    AN --> AO["Component 41"]
    AO --> AP["Component 42"]
    AP --> AQ["Component 43"]
    AQ --> AR["Component 44"]
    AR --> AS["Component 45"]
    AS --> AT["Component 46"]
    AT --> AU["Component 47"]
    AU --> AV["Component 48"]
    AV --> AW["Component 49"]
    AW --> AX["Component 50"]

Cable Management

14

Tool Storage

L. (×1) n. (×1)

n L

One-Year Limited Warranty

This Helder product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of One (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later. The warranty provider's responsibility with respect to this limited warranty shall be limited solely to repair or replacement, at the provider's discretion, of any product that fails during normal use of this product in its intended manner and in its intended environment. Inoperability of the product or part(s) shall be determined by the warranty provider. If the product has been discontinued, the warranty provider reserves the right to replace it with a model of equivalent quality and function.

This warranty does not cover damage or defect caused by misuse, neglect, accident, alteration, abuse, improper installation or maintenance. EXCEPT AS PROVIDED HEREIN, THE WARRANTY PROVIDER MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. This warranty provides you with specific legal rights, and you may also have additional rights that vary from state to state.

To obtain warranty coverage, contact the Helder Customer Service Department to obtain a return merchandise authorization ("RMA") number, and return the defective product to Helder along with the RMA number and proof of purchase. Shipment of the defective product is at the purchaser's own risk and expense.

For more information or to arrange service, visit www.clearashelder.com or call Customer Service at 212-594-2353.

Product warranty provided by the Gradus Group.

www.gradusgroup.com

Helder is a registered trademark of the Gradus Group.

© 2024 Gradus Group LLC. All Rights Reserved. GG1

HELDER®

A Gradus Group Brand