KATWM70TLMA - Washing machine Kogan - Free user manual and instructions

USER MANUAL KATWM70TLMA Kogan

Technical line drawing of a mechanical assembly with two vertical supports and a central oval component (no text or symbols)

TILT ADJUSTABLE TV WALL MOUNT FOR

(SUITABLE FOR 32-70" TVS)

KATWM70TLMA

SAFETY & WARNINGS

Read the entire user guide before you start installation and assembly. If you have any questions regarding any of the instructions or warnings, contact your local distributor for assistance.

CAUTION: Use with products heavier than the rated weights indicated may result in instability causing possible injury.

• Please closely follow the assembly instructions. Improper installation may result in damage or serious personal injury.
• Safety gear and proper tools must be used. This product should only be installed by professionals.
• This product is designed to be installed on solid concrete walls, masonry walls or wood stud walls.
• Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
• Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
• This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
• Never exceed the maximum load capacity of 45kg or it may result in product failure or personal injury.

IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, contact your place of purchase for a replacement.

MAINTENANCE: Check that the product is secure and safe to use at regular intervals (at least every three months).

VESA Compatible 75x75 100x100 100x150 100x200 150x100 150x150 200x100 200x200 300x200 300x300 400x200 400x300 400x400 70" MAX FLAT/CURVED 45kg (99lbs) RATED

COMPONENTS

Technical line drawing of a rectangular mechanical component with bolt holes and internal oval cutouts (no text or symbols)

A Wall mount (x1)

B Spirit level (x1)

C TV bracket (x1)

D TV bracket (x1)

M-A M6x30 Screw (x4)

M-B M8x30 Screw (x4)

M-C D8 Washer (x4)

M-D Spacer (x4)

W-A ST6.3x55 Screw (x4)

W-B Wall Anchors (x4)

W-C D6 Washer (x4)

Tools Required

Stud Finder

Pen/pencil

Drill & Drill Bit

Ratchet & Sockets

Phillips head screwdriver

ASSEMBLY

Step 1:

Step 1: Using a pencil and spirit level (B), mark the desired position for the mount on your wall, using the Wall Mount (A) as a template for the hole positions. Note: When using spirit level, ensure the bubble is centred as per the image shown below.

If mounting on dry wall or plaster-board, use a stud finder first to check positions of wall studs and ensure the position is free from electrical wiring. Using a drill, create the pilot holes.

Drywall / plaster: Use a 4.5mm or 3/16" drill bit, drilling 55mm deep – 4 holes

Masonry / concrete: Use a 10mm or 3/8'' drill bit, drilling 60mm deep - 4 holes

Step 2:

Drywall / plaster: Attach the wall mount (A) to the wall using the 4 ST6.3x55 screws (W-A) and D6 washers (W-C). Do not use wall anchors.

Masonry / concrete: Insert wall anchors (W-B) into all 4 drilled holes. Attach the wall mount (A) to the wall using the 4 ST6.3x55 screws (W-A) and D6 washers (W-C).

W-C W-A

W-B W-C W-A

Step 3:

Align the brackets (C) & (D) with your TV's VESA holes and secure using supplied screws ("M-" set), Washer (M-C) and spacers (M-D) depending on required length.

Technical diagram showing three types of bolt and nut assembly symbols: checkmark, bolt, and washer

X Too long Too Short

M-A M-B M-C C D M-D TOP

Step 4:

- Hook the TV with brackets installed onto the wall mount. 2 people should carry the TV to prevent damage. Note: The TV can be mounted in 2 different positions depending on your requirements. Pay attention to ensure it is properly positioned before proceeding.

- Once in place, close the safety latches and fastens the safety screws to secure the brackets in place.

Diagram showing two people interacting with a wall-mounted panel, one holding a rectangular object and the other with an arrow indicating rotation (no text or symbols present)

Technical illustration showing a mechanical assembly with a screwdriver inserted and rotating the component (no text or symbols present)

Step 5:

Adjust to the desired angle and tighten the knobs as shown.

Technical line drawing of a mechanical assembly with rotating components and mounting brackets (no text or symbols)

Illustration of a hand pressing down on a tablet screen with a curved arrow indicating rotation (no text or symbols)

NOTES

Need more information?

We hope that this user guide has given you the assistance needed for a simple set-up.

For the most up-to-date guide for your product, as well as any additional assistance you may require, head online to help.kogan.com

kogan.com