KATVFSW75LM - Washing machine Kogan - Free user manual and instructions

USER MANUAL KATVFSW75LM Kogan

Line drawing of a simple metal frame structure with four legs and a central horizontal panel (no text or symbols)

SOLID WOOD FOUR- LEGGED TV FLOOR STAND

(SUITABLE FOR 49-75" TVS)

KATVFSW75LM

SAFETY & WARNINGS

Read the entire user guide before you start installation and assembly. If you have any questions regarding any of the instructions or warnings, contact your local distributor for assistance.

CAUTION: Use with products heavier than the rated weights indicated may result in instability causing possible injury.

• Please closely follow the assembly instructions. Improper installation may result in damage or serious personal injury.
• Safety gear and proper tools must be used. This product should only be installed by professionals.
• This product includes an anti-tip kit that must be used in conjunction with the product and will prevent the unit from falling or tipping over. Follow the enclosed information to properly install these safety accessories.
• This product is designed to be installed on solid concrete walls, masonry walls or wood stud walls.
• Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
• Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
• This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
• Never exceed the maximum load capacity of 50kg or it may result in product failure or personal injury.

IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, contact your place of purchase for a replacement.

MAINTENANCE: Check that the product is secure and safe to use at regular intervals (at least every three months).

VESA Compatible 100x100 200x100 200x200 300x200 300x300 400x200 400x300 400x400 600x400 75" MAX 40kg (88lbs) RATED

COMPONENTS

A (x1)

B (x4)

C Left (x1)

D Right (x1)

E (x1)

F TV brackets (x2)

G (x2)

H Cable Clip (x6)

IST4.2×12
Screw (x6)

J M6x35
Screw (x8)

KM6x70
Screw (x4)

L 4-5mm
Allen Key (x1)

M 4mm Allen
Key (x1)

M-A M6x14
Screw (x4)

M-B M8x16
Screw (x4)

M-C M6x30
Screw (x4)

M-D M8x35
Screw (x4)

M-E D8
Washer (x4)

M-F Spacer (x4)

M-G Spacer (x4)

P-A Anti-fall
Cable (x1)

P-B Cable
Clips (x2)

P-C Anti-fall
Brackets (x1)

P-D Cable
Screws (x2)

P-E ST4.8x38
Screw (x1)

P-F Wall
Anchor (x1)

P-G D5
Washer (x2)

Tools required for installation (not supplied)

Phillips head screwdriver

Stud finder

Pencil

Drill

Wrench

This product includes safety kits that must be used in conjunction with the product to prevent the product from falling or tipping over. Please follow the enclosed information to properly install these safety accessories. In no event shall the Seller be liable for any direct, indirect, punitive, incidental, special consequential damages, to property or life, whatsoever arising out of or connected with the use or misuse of this product.

ASSEMBLY

Step 1:

Loosen the fasteners on part (A) and remove the end covers (A1 & A2).

A L A2 A1

Step 2:

Attach the 4 legs (B) and secure them in place using 4 M6x35 screws (J).

B A1 J

Step 3:

A2

Step 4:

Ensure the 2 Limiting screws are facing upwards and attach parts (C & D) to the part (E) using 4 M6x35 Screws (J).

E 10mm D C M J

Step 5:

Attach the assembled frame to the legs.

Insert (G) into the frame ensuring the notch is vertical then secure the frame in place using 4 M6x70 Screws (K).

Technical diagram illustrating a mechanical assembly with labeled components and directional arrows indicating motion or assembly steps.

Step 6:

• Loosen the fasteners on the bottom of the brackets and flip the latch down.
• Attach the brackets (F) to the rear of the TV and secure them in place using the supplied screws ("M-" set) and washers (M-E).
• The cable clips (P-B) will need to be attached to the upper holes on the bracket (F).

Note: Depending on your TV you may need to install the spacers (M-F & M-G).

✓ Too Iong Too Short ✓ Too Iong Too Short F F TOP 1 2 M-A M-B P-B M-E M-C M-D P-B M-E M-F M-G M-A M-B M-E M-C M-D M-E M-F M-G

Step 7:

- Carefully attach the TV to the stand. Enlist the help of a second person to safely carry the TV. Note: Ensure the TV bracket arms are between the 2 limiting screws.

- Close the clasp on the lower TV brackets and tighten the screw.

- Attach cable clips (H) to the legs using the ST4.2x12 screws (I).

Technical diagram illustrating a mechanical assembly with labeled steps and component illustrations

Step 8:

• To avoid the TV falling, it is highly recommended to install the anti-fall hardware.
• Mark the desired position for the anti-fall bracket (P-C).
• Drywall / plaster: Drill a pilot hole using a 3.5mm drill bit and drill.
• Masonry / concrete: Drill a pilot hole using a 7mm drill bit and drill.

Step 9:

Drywall / plaster: Secure the anti-fall bracket (P-C) to the wall using the ST4.8x38 Screw (P-E).

Masonry / concrete: Secure the anti-fall bracket (P-C) to the wall using the wall anchor (P-F) and ST4.8x38 Screw (P-E).

Step 10:

Using the anti-fall rope (P-A), cable clips (P-B) and rope screws (P-D) secure the TV to the Wall.

Note: Ensure there is enough tension on the rope so that the TV will not tip over.

P-B P-A P-D

NOTES

Need more information?

We hope that this user guide has given you the assistance needed for a simple set-up.

For the most up-to-date guide for your product, as well as any additional assistance you may require, head online to help.kogan.com

kogan.com